Physicochemical properties of poly(ethylene oxide)-based composite polymer electrolytes with a silane-modified mesoporous silica SBA-15

Mesoporous silica SBA-15 was surface-modified by γ-glycidoxypropyltrimethoxy silane (GPTMS), and novel poly(ethylene oxide) (PEO)-based composite polymer electrolytes (CPE) using the silane-modified SBA-15 (SBA-15-GPTMS) as filler were prepared and characterized. The results of the low-angle X-ray diffraction (XRD) patterns and Fourier-transform infrared (FT-IR) spectroscopy indicated that GPTMS has been successfully attached to the surface of SBA-15 with a high degree of mesoscopic hexagonal pore structure. The incorporation of SBA-15-GPTMS in the PEO-LiClO₄ matrix effectively reduced the PEO crystallinity and obviously improved the conductivity and electrochemical stability of the CPEs. The CPE with 10 wt.% SBA-15-GPTMS provided the highest conductivity among all the tested CPEs, about 2-3 orders of magnitude higher than that of the PEO-LiClO₄ matrix below the melting temperature of PEO. The reasons that the CPEs using SBA-15-GPTMS as filler showed higher conductivity than that with SBA-15 were discussed.     

Effect of surface modified porous inorganic-organic hybrid polyphosphazene nanotubes on the properties of polyethylene oxide based solid polymer electrolytes

2-(2-methyloxyethoxy)ethanol modified poly (cyclotriphosphazene-co-4,4′-sufonyldiphenol) (PZS) nanotubes were synthesized and solid composite polymer electrolytes based on the surface modified polyphosphazene nanotubes added to PEO/LiClO₄ model system were prepared. Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM) were used to investigate the characteristics of the composite polymer electrolytes (CPE). The ionic conductivity, lithium ion transference number and electrochemical stability window can be enhanced after the addition of surface modified PZS nanotubes. The electrochemical investigation shows that the solid composite polymer electrolytes incorporated with PZS nanotubes have higher ionic conductivity and lithium ion transference number than the filler SiO₂. Maximum ionic conductivity values of 4.95 × 10⁻⁵ S cm⁻¹ at ambient temperature and 1.64 × 10⁻³ S cm⁻¹ at 80 °C with 10 wt % content of surface modified PZS nanotubes were obtained and the lithium ion transference number was 0.41. The good chemical properties of the solid state composite polymer electrolytes suggested that the inorganic-organic hybrid polyphosphazene nanotubes had a promising use as fillers in solid composite polymer electrolytes and the PEO₁₀-LiClO₄-PZS nanotubes solid composite polymer electrolyte can be used as a candidate material for lithium polymer batteries.     

Ionic conductivities of solid polymer electrolyte/salt systems for lithium secondary battery

We establish a new ionic conductivity model based on the Nernst-Einstein equation in which the diffusion coefficient is derived from modified double lattice-nonrandom-Pitzer-Debye-Hückel (MDL-NR-PDH) model. The proposed model takes into account the mobility of the salt and the motion of the polymer host simultaneously by expressing the effective chemical potential as the sum of chemical potentials of the salt and the polymer. To describe the segmental motion of the polymer chain, which is the well-known conduction mechanism for solid polymer electrolyte (SPE) systems, the effective co-ordinated unit parameter is introduced. The obtained co-ordinated unit parameter for each state is used to describe the behavior of the ionic conductivities of the given systems. Good agreement is obtained upon comparison with experimental data of various PEO and salt systems in the interested ranges.     

Study of a new polymer electrolyte poly(ethylene oxide): NaClO3 with several plasticizers for battery application

Sodium ion conducting thin film polymer electrolytes based on poly(ethylene oxide) (PEO) complexed with NaClO₃ were prepared by a solution‐casting method. Characterization by XRD, IR spectroscopy and AC conductivity has been carried out on these thin film electrolytes to analyse their properties. The conductivity studies show that the conductivity value of PEO:NaClO₃ complex increases with the increase in salt concentrations. Increase in conductivity was found in the electrolyte system by the addition of low molecular weight polymer poly(ethylene glycol) (PEG) and the organic solvents dimethylformamide (DMF) and propylene carbonate (PC). Using these electrolyte systems, cell parameters were measured from the discharge study with the application of load 100 kΩ at room temperature with common cell configuration Na|electrolyte|C:I₂:electrolyte. The open circuit voltage (OCV) ranges from 2.81 to 3.23 V and the short circuit current (SCC) ranges from 340 to 1180 µA. © 2001 Society of Chemical Industry     

Composite polymer electrolyte incorporating WO3 nanofillers with enhanced performance for dendrite-free solid-state lithium battery

All solid-state lithium batteries (ASS-LBs) with polymer-based solid electrolytes are a prospective contender for the next-generation batteries because of their high energy density, flexibility, and safety. Among all-polymer electrolytes, PEO-based solid polymer electrolytes received huge consideration as they can dissolve various Li salts. However, the development of an ideal PEO-based solid polymer electrolyte is hindered by its insufficient tensile strength and lower ionic conductivity due to its semi-crystalline and soft chain structure. In order to lower the crystallization and improve the performance of PEO-based solid polymer electrolyte, tungsten trioxide (WO₃) nanofillers were introduced into PEO matrix. Herein, a PEO₂₀/LiTFSI/x-WO₃ (PELI-xW) (x = 0%, 2.5%, 5%, 10%) solid composite polymer electrolyte was prepared by the tape casting method. The solid composite polymer electrolyte containing 5 wt% WO₃ nanofillers achieved the highest ionic conductivity of 7.4 × 10^-4 S cm^-1 at 60 °C. It also confirms a higher Li-ion transference number of 0.42, good electrochemical stability of 4.3V, and higher tensile strength than a PEO/LiTFSI (PELI-0W) fillers-free electrolyte. Meanwhile, the LiFePO₄│PELI-xW│Li ASS-LBs demonstrated high performance and cyclability. Based on these findings, it can be considered a feasible strategy for the construction of efficient and flexible PEO-based solid polymer electrolytes for next-generation solid-state batteries.     

Gel-based composite polymer electrolytes with novel hierarchical mesoporous silica network for lithium batteries

In the present work, novel gel-based composite polymer electrolytes for lithium batteries were prepared by introducing a hierarchical mesoporous silica network to the poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP)-based gel electrolytes. As compared with the PVDF-HFP-based gel electrolytes with/without conventional nano-sized silica fillers, the novel electrolytes have shown more homogeneous microstructure, higher ionic conductivity and better mechanical stability, which could be caused by the strong silica network and the effective interactions among the polymer, the liquid electrolytes and the silica. Moreover, the cell with this kind of electrolytes could achieve a discharge capacity as much as 150 mAh g⁻¹ at room temperature (LiCoO₂ as the cathode active material), with high Coulomb efficiency.     

New boron compounds as additives for lithium polymer electrolytes

A new class of difluoroalkoxyborane compounds ([R_nOBF₂]₂) containing oligooxyethylene groups of various molecular weight in the form of a methyl monoether (R_n = CH₃(OCH₂CH₂)_n, n = 1, 2, 3 and 7) has been obtained in the reaction of BF₃ etherate with appropriate glycols. ¹H, ¹¹B and ¹⁹F NMR spectral analysis of the derivatives obtained was carried out and the properties as Lewis acids of these derivatives have been compared with that of corresponding trialkoxyboranes and boron trifluoride in reaction with pyridine. The strength of the interaction of [R₂OBF₂]₂ with the differing in “hardness” anions of various lithium salts has been analyzed on the basis of NMR spectra. The [R_nOBF₂]₂ obtained were used as additives for polymer electrolytes containing PEO as polymer matrix and various lithium salts at an equimolar ratio of the boron compound to salt. The highest ionic conductivities, in the order 10⁻⁵ to 10⁻⁴ S cm⁻¹ at 20-70 °C, were achieved for systems containing LiI and LiN(CF₃SO₂)₂. The lithium transference number (t₊) values, determined by the electrochemical method by steady-state technique for LiF and LiCF₃SO₃ are in the 0.6-0.8 range.     

Nanocomposite polymer electrolytes containing silica nanoparticles: Comparison between poly(ethylene glycol) and poly(ethylene oxide) dimethyl ether

Nanocomposite polymer electrolytes consisting of low molecular weight poly(ethylene oxide) (PEO), iodine salt MI (M = K⁺, imidazolium⁺), and fumed silica nanoparticles have been prepared and characterized. The effect of terminal group in PEO, i.e., hydroxyl (? OH) and methyl (CH₃) using poly(ethylene glycol) (PEG) and PEO dimethyl ether (PEODME), respectively, was investigated on the interactions, structures, and ionic conductivities of polymer electrolytes. Wide angle X‐ray scattering (WAXS), differential scanning calorimetry (DSC), and complex viscositymeasurements clearly showed that the gelation of PEG electrolytes occurred more effectively than that of PEODME electrolytes. It was attributed to the fact that the hydroxyl groups of PEG participated in the hydrogen‐bonding interaction between silica nanoparticles, and consequently helped to accelerate the gelation reaction, as confirmed by FTIR spectroscopy. Because of its interaction, the ionic conductivities of PEG electrolytes (maximum value ～ 6.9 × 10^?4 S/cm) were lower than that of PEODME electrolytes (2.3 × 10^?3 S/cm). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

A highly conductive organic-inorganic hybrid electrolyte based on co-condensation of di-ureasil and ethylene glycol-containing alkoxysilane

Organic-inorganic hybrid electrolytes based on di-ureasil backbone structures by reacting poly(propylene glycol)-block-poly(ethylene glycol)-block-poly(propylene glycol) bis(2-aminopropyl ether) (ED2000) with 3-(triethoxysilyl)propyl isocyanate (ICPTES), followed by co-condensation with methoxy(polyethylenoxy)propyl trimethoxysilane (MPEOP) in the presence of LiClO₄ were prepared and characterized by a variety of techniques. The hybrid electrolytes showed good resistance to crystallization and excellent conductivity for use in lithium-ion batteries, as determined by differential scanning calorimetry (DSC) and impedance measurements, respectively. The temperature dependence of the ionic conductivity exhibited a VTF (Vogel-Tamman-Fulcher)-like behavior for all the compositions studied and a maximum ionic conductivity value of 6.9 × 10⁻⁵ S cm⁻¹, a relatively high value for solid polymer electrolytes, was achieved at 30 °C for the hybrid electrolyte with a [O]/[Li] ratio of 16. A microscopic view of the dynamic behavior of the polymer chains (¹³C) and the ionic species (⁷Li) was provided by the ¹H and ⁷Li line widths measured from 2D ¹H-¹³C WISE (Wideline Separation) and variable temperature ⁷Li static NMR, respectively, to elucidate the influence of the mobility of the polymer chains and the charge carriers on the observed ionic conductivity. The present salt-free hybrid electrolyte after plasticization with 1 M LiClO₄ in EC/PC solution exhibited a swelling ratio of 275% and reached an ionic conductivity value up to 8.3 × 10⁻³ S cm⁻¹ at 30 °C, which make it a good candidate for the further development of advanced rechargeable lithium-ion batteries.     

Improved photovoltage and performance by aminosilane-modified PEO/P(VDF-HFP) composite polymer electrolyte dye-sensitized solar cells

A PEO/P(VDF-HFP) composite polymer electrolyte was modified by different amounts of NH₂-end functional silane (3-amonopropyltriethoxysilane, APTS). Fourier transform infrared (FT-IR), X-ray diffraction (XRD) and differential scanning calorimetry (DSC) were carried out to examine the configuration changes of the polymer electrolyte. The newly formed Si-O-Si network and interactions influenced the ionic conductivity of the APTS-modified polymer electrolyte and also enhanced the connection of the polymer electrolyte with the electrodes of the dye sensitized solar cells (DSSCs). The cyclic voltammograms and electrochemical impedance measurements indicated that the APTS deprotonated the TiO₂ photoanode surface and negatively changed the Fermi energy level and the conduction band edge to the vacuum level. This effectively reduced the interface recombination in the DSSC and improved the open circuit voltage. With moderate APTS content (0.1 M) modification, the DSSC exhibited a 58 mV improvement of photovoltage and an improved performance of 5.08% compared with 3.74% of the original DSSC.     

Ionic liquid mediated magnesium ion conduction in poly(ethylene oxide) based polymer electrolyte

Magnesium ion conduction in poly(ethylene oxide) (PEO) based polymer electrolyte incorporated with room temperature ionic liquid (RTIL) is reported. The electrolyte films comprise the PEO complexed with magnesium trifluoromethanesulfonate (or magnesium triflate) added with different amount of ionic liquid, 1-ethyl-3-methylimidazolium trifluoromethanesulfonate (EMITf). The polymer electrolyte with ∼50 wt.% of ionic liquid offers a maximum electrical conductivity of ∼5.6 × 10⁻⁴ S cm⁻¹ at room temperature (∼25 °C) with improved thermal and electrochemical stabilities. The Mg²⁺ ion conduction in the PEO-complex is confirmed from cyclic voltammetry, impedance and transport number measurements. A significant increase in the Mg²⁺ ion transport number (tMg2+) is observed with increasing content of the ionic liquid in PEO–Mg salt complex and the maximum value is obtained to be ∼0.45 for ∼50 wt.% of ionic liquid. The interaction of imidazolium cations with ether oxygen of PEO, as evidenced from FTIR and Raman studies, play an important role in the substantial enhancement in the tMg2+ value.     

Electrochemical characteristics of phase-separated polymer electrolyte based on poly(vinylidene fluoride-co-hexafluoropropane) and ethylene carbonate

A polymer electrolyte based on microporous poly(vinylidene fluoride-co-hexafluoropropane) (PVdF-HFP) film was studied for use in lithium ion batteries. The microporous PVdF-HFP (Kynar 2801) matrix was prepared from a cast of homogeneous mixture of PVdF-HFP and solvents such as ethylene carbonate (EC), dimethyl carbonate (DMC), and ethyl methyl carbonate (EMC). After evaporation of DMC and EMC, a sold film of the PVdF-HFP and the EC mixture was obtained. EC-rich phase started its formation in the PVdF-HFP/EC film at EC content of about 60 wt.% based on the total weight of PVdF-HFP and EC. The formation of the new phase resulted in the abrupt increase of the porosity of the PVdF-HFP matrix from 32 to 62%. The ionic conductivity of the film soaked in 1 M LiPF₆-EC/DMC=1/1 was significantly increased from order of 10⁻⁴ S/cm to order of 10⁻³ S/cm at the EC content of 60 wt.%. Thermal and spectroscopic investigations showed that most of the EC interact with PVdF-HFP with the EC content being below 60 wt.%. MCMB/polymer electrolyte/LiCoO₂ cells employing the microporous PVdF-HFP polymer film showed stable charging/discharging characteristics at 1C rate and good rate capability.     

Effect of zwitterionic salt on the electrochemical properties of a solid polymer electrolyte with high temperature stability for lithium ion batteries

In this study, we prepare a kind of solid polymer electrolyte (SPE) based on N-ethyl-N′-methyl imidazolium tetrafluoroborate (EMIBF₄), LiBF₄ and poly(vinylidene difluoride-co-hexafluoropropylene) [P(VdF-HFP)] copolymer. The resultant SPE displays high thermal stability above 300 °C and high room temperature ionic conductivity near to 10⁻³ S cm⁻¹. Its electrochemical properties are improved with incorporation of a zwitterionic salt 1-(1-methyl-3-imidazolium)propane-3-sulfonate (MIm3S). When the SPE contains 1.0 wt% of the MIm3S, it has a high ionic conductivity of 1.57 × 10⁻³ S cm⁻¹ at room temperature, the maximum lithium ions transference number of 0.36 and the minimum apparent activation energy for ions transportation of 30.9 kJ mol⁻¹. The charge-discharge performance of a Li₄Ti₅O₁₂/SPE/LiCoO₂ cell indicates the potential application of the as-prepared SPE in lithium ion batteries.     

Enhancement of electrochemical properties of hot-pressed poly(ethylene oxide)-based nanocomposite polymer electrolyte films for all-solid-state lithium polymer batteries

PEO₁₆-LiClO₄-ZnAl₂O₄ nanocomposite polymer electrolyte (NCPE) films prepared by hot-pressing method have been investigated. In order to compare with the hot-pressed NCPEs, the NCPE films have also been prepared using the conventional solution-casting method. Field emission scanning electron microscopy (FESEM), differential scanning calorimetry (DSC), conductivity (σ) and interface property studies have been carried out on above two kinds of films. The results show that the NCPE film prepared by hot-pressing method has smoother surface, higher interface stability, lower crystallization and melting temperature values than that prepared by solution-casting method. An all-solid-state lithium polymer battery using the hot-pressed NCPE film as electrolyte, lithium metal and LiFePO₄ as anode and cathode respectively, shows high discharge specific capacity, good rate capacity, high coulombic efficiency, and excellent cycling stability as revealed by galvanostatical charge/discharge cycling tests.     

Effect of the addition of hydrophobic clay on the electrochemical property of polyacrylonitrile/LiClO4 polymer electrolytes for lithium battery

In this study, an organoclay, ALA-MMT, was prepared by the ionic exchange reaction of montmorillonite (MMT) with 12-aminododecanoic acid (ALA). ALA-MMT was then used as a filler to prepare a series of composite polymer electrolytes based on polyacrylonitrile (PAN) and LiClO₄. The effect of the addition of ALA-MMT on the properties of the composite polymer electrolytes (CPEs) was investigated by XRD, FT-IR, DSC, tensile strength, AC impedance, and cyclic voltammetry measurements. It was found that the ALA-MMT particles were well dispersed in the CPEs. Owing to the incorporation of ALA-MMT, a higher fraction of the free anions was obtained, indicating that the lithium salt dissolved in the PAN matrix more effectively for the CPE than in the PAN/LiClO₄ polymer electrolyte. Moreover, the glass-transition temperature was reduced, benefiting the ion transport. The best ionic conductivity at room temperature was obtained from the CPE with 7 wt% of the modified clay and 0.6 M LiClO₄ per PAN repeat unit (CPE-7) and was more than seven times higher than that from the corresponding PAN/LiClO₄ polymer electrolyte (CPE-0). The mechanical property and the cation transference number, t₊, of CPE-7 are largely increased compared to that of CPE-0. Besides, the CPEs were electrochemically stabilized up to 4.75 V and the corresponding cell exhibited excellent electrochemical stability and cyclability over the potential range between 0 V and 4.0 V vs. Li/Li⁺.     

New polymer electrolytes based on ether sulfate anions for lithium polymer batteries: Part II: Conductivity and transport properties of blended and cross-linked ionomers

Multifunctional ionomers based on poly(oxyethylene)-co-poly(epichlorohydrin) random copolymers were blended with poly(oxyethylene) or cross-linked through urethane curing. Their conductivities, transference numbers and electrochemical stability were investigated. The cross-linked materials exhibited good mechanical properties. Gelled by liquid organic electrolytes they provided conductivities very close to that of the liquid electrolyte. A thorough comparative investigation of the cationic transference numbers of cross-linked and uncross-linked ionomers was performed. From these data it may be assumed that the cell electrical polarization is enough to induce chain disentanglements, which result in a significant anionic transference number.     

Novel polymer electrolyte composed of poly(ethylene oxide), lithium triflate,and benzimidazole

This work has demonstrated that the incorporation of benzimidazole derivatives, 2,2′‐p‐phenylene‐bisindole (PPBI), enhances the ionic conductivity of a poly(ethylene oxide) (PEO)–based electrolyte by 20 times more than the plain system. Specific interactions among amino group, ethyl oxide, and lithium cation were investigated using differential scanning calorimetry (DSC), FTIR, and alternating current impedance. The DSC characterization confirms that the initial addition of PPBI is able to enhance the PEO crystallinity attributed to the interaction between the negative charge from the amino group and the lithium cation. Three types of complexes are present: complex I is present in the PEO phase, complex II resides at interphase, and complex III is located within the PPBI domain. Complex II plays the key role in stabilizing these two microstructure phases. FTIR spectra confirm that because of the presence of PPBI one is able to dissolve lithium salts more easily than in the plain electrolyte system and thus increase the fraction of free ions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 719–725, 2004     

Utilization of poly(ethylene terephthalate) waste for preparing disodium terephthalate and its application in a solid polymer electrolyte

A widespread application and nonbiodegradability of the poly(ethylene terephthalate) (PET) have created a huge amount of waste, which is imposing a serious life-threatening environmental problem. In this study, we have utilized the PET waste to synthesize disodium terephthalate (DST), an organic salt having two Na⁺ ions per molecule. The purity of the DST phase was confirmed by Fourier transform infrared spectroscopy, X-ray diffractometry (XRD), and thermogravimetric analysis (TGA). A new poly(ethylene oxide)–DST polymer electrolyte was synthesized for utilizing Na⁺ ions of the DST. The electrical conductivity of the electrolyte was optimized by varying the [O]/[Na⁺] mole ratio with temperature and the results were explained using the XRD and differential scanning calorimetry studies. The TGA study showed that the electrolyte is thermally stable up to 200 °C. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47612.     

Vanadium doped ceramic matrix Li6.7La3Zr1.7V0.3O12 enabled PEO-based solid composite electrolyte with high lithium ion transference number and cycling stability

Solid polymer electrolytes (SPEs) have attracted much attention because of their potential in improving energy density and safety. Vanadium doped ceramic matrix Li_6.7La₃Zr_1.7V_0.3O₁₂ (LLZVO) was synthesized by high-temperature annealing, and formed a composite electrolyte with polyethylene oxide (PEO). Compared with pure PEO electrolyte membrane, the composite electrolyte membrane exhibited better ionic conductivity (30 °C: 3.2 × 10^?5 S cm^?1; 80 °C: 3.6 × 10^?3 S cm^?1). The combination of LLZVO was beneficial to improve the lithium ion transference number (t_Li⁺) of SPE, which was as high as 0.81. The Li/SPE/LiFePO₄ battery shows good cycling ability, with a specific capacity of 142 mAh g^?1 after a stable cycle of 150 cycles. Meanwhile, the symmetrical lithium battery with composite electrolyte can work continuously for 1200 h without short circuit at the current density of 0.1 mA cm^?2 at 50 °C, and the capacity is 0.176 mAh. Vanadium doped ceramic matrix LLZVO as an active ionic conductor, improved the overall performance of solid electrolyte.     

Polyterthiophene/CNT composite as a cathode material for lithium batteries employing an ionic liquid electrolyte

A polyterthiophene (PTTh)/multi-walled carbon nanotube (CNT) composite was synthesised by in situ chemical polymerisation and used as an active cathode material in lithium cells assembled with an ionic liquid (IL) or conventional liquid electrolyte, LiBF₄/EC-DMC-DEC. The IL electrolyte consisted of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF₄) containing LiBF₄ and a small amount of vinylene carbonate (VC). The lithium cells were characterised by cyclic voltammetry (CV) and galvanostatic charge/discharge cycling. The specific capacity of the cells with IL and conventional liquid electrolytes after the 1st cycle was 50 and 47 mAh g⁻¹ (based on PTTh weight), respectively at the C/5 rate. The capacity retention after the 100th cycle was 78% and 53%, respectively. The lithium cell assembled with a PTTh/CNT composite cathode and a non-flammable IL electrolyte exhibited a mean discharge voltage of 3.8 V vs Li⁺/Li and is a promising candidate for high-voltage power sources with enhanced safety.