Effect of Mn content on the structure and electrochemical characteristics of La0.7Mg0.3Ni2.975−xCo0.525Mnx (x = 0-0.4) hydrogen storage alloys

The effect of Mn content on the crystal structure and electrochemical characteristics of La_0.7Mg_0.3Ni_2.975−xCo_0.525Mn_x (x = 0, 0.1, 0.2, 0.3, 0.4) alloys has been studied systematically. The results of the Rietveld analyses show that all these alloys mainly consist of two phases: the La(La,Mg)₂Ni₉ phase with the rhombohedral PuNi₃-type structure and the LaNi₅ phase with the hexagonal CaCu₅-type structure. The pressure-composition isotherms shows that the partial substitution of Mn for Ni results in lower desorption plateau pressure and steeper pressure plateau of the alloy electrodes. For a Mn content of x = 0.3, the electrochemical performances, including specific discharge capacity, high rate chargeability (HRC) and high rate dischargeability (HRD), of the alloy are preferable. Moreover, the data of the polarization resistance R_p and the exchange current density I₀ of the alloy electrodes is consistent with the results of HRC and HRD. The hydrogen diffusion coefficient D increases with increasing Mn content, and thereafter increases the low temperature dischargeability (LTD) of the alloy electrodes.     

Microstructures and electrochemical properties of Mg0.9Ti0.1Ni1−xMx (M = Co, Mn; x = 0, 0.1, 0.2) hydrogen storage alloys

Mg-Ni-Ti-based hydrogen storage alloys Mg_0.9Ti_0.1Ni_1−xM_x (M = Co, Mn; x = 0, 0.1, 0.2) were prepared by means of mechanical alloying (MA). The effects of partial substitution of Ni with Co or Mn on the microstructures and electrochemical performance of the alloys were investigated. The result of X-ray diffraction (XRD) shows that the alloys exhibit dominatingly amorphous structures. The electrochemical measurements indicate that the substitution of Ni can dramatically enhance the cycle stability of Mg-Ni-Ti-based alloys. After 50 charge/discharge cycles, the capacity retention rate of the alloy electrodes increases from 30% (Mg_0.9Ti_0.1Ni) to 59% (Mg_0.9Ti_0.1Ni_0.9Co_0.1), 58% (Mg_0.9Ti_0.1Ni_0.9Mn_0.1), 46% (Mg_0.9Ti_0.1Ni_0.8Co_0.2) and 53% (Mg_0.9Ti_0.1Ni_0.8Mn_0.2), respectively. Among these alloys, the Mg_0.9Ti_0.1Ni_0.9Mn_0.1 alloy presents better overall electrochemical performance. The cyclic voltammograms (CV) and anti-corruption test reveal that the electrochemical cycle stability of these alloys is improved by substituting Ni with Co or Mn.     

Study on phase structure and electrochemical properties of Ml1−xMgxNi2.80Co0.50Mn0.10Al0.10 (x = 0.08, 0.12, 0.20, 0.24, 0.28) hydrogen storage alloys

Phase structure and electrochemical properties of the Ml_1−xMg_xNi_2.80Co_0.50Mn_0.10Al_0.10 (x = 0.08, 0.12, 0.20, 0.24, 0.28) (Ml = La-rich mixed lanthanide) alloys were studied. X-ray diffraction (XRD) analysis and Rietveld refinement show that the alloys consist mainly of LaNi₅ and (La,Mg)Ni₃ phase. Due to variation in phases of the alloys, the maximum discharge capacity, the high rate dischargeability (HRD), and the low temperature dischargeability increase first and then decrease. The maximum discharge capacity increases from 322 mAh g⁻¹ (x = 0.08) to 375 mAh g⁻¹ (x = 0.12), and then decreases to 351 mAh g⁻¹ (x = 0.28) with increasing x. As the case of x = 0.20, HRD at 1200 mA g⁻¹ and discharge capacity at 233 K reaches 41.7% and 256 mAh g⁻¹, respectively. The cycling stability is improved by substituting La with Ml and B-site multi-alloying, and the capacity retention of Ml_0.72Mg_0.28Ni_2.80Co_0.50Mn_0.10Al_0.10 at the 200th cycle is 71%.     

Electrochemical hydrogen storage in (Ti1−xVx)2Ni (x = 0.05-0.3) alloys comprising icosahedral quasicrystalline phase

For (Ti_1−xV_x)₂Ni (x = 0.05, 0.1, 0.15, 0.2 and 0.3) ribbons, synthesized by arc-melting and subsequent melt-spinning techniques, an icosahedral quasicrystalline phase was present, either in the amorphous matrix or together with the stable Ti₂Ni-type phase. With increasing x values, the maximum discharge capacity of the alloy electrodes increased until reached 271.3 mAh/g when x = 0.3. The cycling capacity retention rates for these electrodes were approximately 80% after a preliminary test of 30 consecutive cycles of charging and discharging. Ti_1.7V_0.3Ni alloy electrode displayed the best high-rate discharge ability of 82.7% at the discharge current density of 240 mA/g.     

Structure and electrochemical characteristics of TiV1.1Mn0.9Nix (x = 0.1-0.7) alloys

The structure and electrochemical properties of TiV_1.1Mn_0.9Ni_x (x = 0.1-0.7) solid solution electrode alloys have been investigated. It is found that these alloys mainly consist of a solid solution phase with body centered cubic (bcc) structure and a C14 Laves secondary phase. The solid solution alloys show easy activation behavior, high temperature dischargeability, high discharge capacity and favorable high-rate dischargeability as a negative electrode material in Ni-MH battery. The maximum discharge capacity is 502 mAh g⁻¹ at 303 K when x = 0.4. Electrochemical impedance spectroscopy (EIS) test shows that the charge-transfer resistance at the surface of the alloy electrodes decreases obviously with increasing Ni content.     

Structure and electrochemical performances of Mg2Ni1−xMnx (x = 0-0.4) electrode alloys prepared by melt spinning

The melt-spinning technique is applied to the preparation of the nanocrystalline and amorphous Mg₂Ni-type alloys with nominal compositions of Mg₂Ni_1−xMn_x (x = 0, 0.1, 0.2, 0.3, 0.4). The as-spun alloy ribbons possessing a continuous length, a thickness of about 30 μm and a width of about 25 mm were prepared. The structures of the as-spun alloy ribbons are characterized by XRD and TEM. The electrochemical performances of the as-spun alloy ribbons are measured by an automatic galvanostatic system. The results show that no amorphous structure is detected in the as-spun Mg₂Ni alloy, whereas the as-spun Mg₂Ni_0.6Mn_0.4 alloy displays a nanocrystalline and amorphous structure, confirming that the substitution of Mn for Ni notably intensifies the amorphous forming ability of the Mg₂Ni-type alloy. The amorphization degree of the as-spun alloys containing Mn increases with increasing spinning rate. The melt spinning also significantly enhances the electrochemical performances such as the discharge capacity and the electrochemical cycle stability of the Mn-containing alloys. Furthermore, the high rate dischargeability (HRD) of the (x ≤ 0.1) alloys increases with an increase in the spinning rate, while for the (x ≥ 0.2) alloys, the HRD exhibits a maximum value at a particular spinning rate, and it varies with the change in Mn contents of the alloys.     

Quantitative study of pH change during LaNi5−xAlx (x = 0, 0.3) discharge process by SECM

Oxygen reduction reaction (ORR) on Pt microelectrode was used for developing a micro pH sensor for scanning electrochemical microscopy (SECM) study in this work. When the potential of Pt microelectrode was held constant in ORR region, the ORR current (cathodic current) increased with decreasing solution pH and vice versa. The response time of the ORR current to pH changes was measured to be ca. 30 ms which implies that the pH response is fast enough for monitoring the temporal pH changes. Furthermore, a fine linear relationship was found to exist between the half wave potential of ORR (E_1/2) and the solution pH value, and the slope is −46 mV/pH. The Pt micro pH sensor was located 1 μm above the LaNi_5−xAl_x (x = 0, 0.3) substrate electrode surface in pH = 9 KOH solution to perform the tip-substrate voltammetry of SECM. In tip voltammogram, the ORR tip current qualitatively reflects the transit solution pH changes during LaNi_5−xAl_x discharge reaction. Also, the minimum values of the solution pH near LaNi₅ and LaNi_4.7Al_0.3 surface during the discharge reaction were quantitatively detected; they were 7.17 and 7.57, respectively. The result indicates that Al partial substitution for Ni degrades the maximum discharge ability of the alloy and decreases the hydrogen diffusion coefficient in alloy bulk.     

Synthesis and characterization of abundant Ni-doped LiNixMn2−xO4 (x = 0.1-0.5) powders by spray-drying method

The structure and electrochemical properties of LiNi_xMn_2−xO₄ cathode materials for lithium ion batteries were studied by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), cyclic voltammetry, and galvanostatic charge-discharge tests. The cathodes with different Ni contents (LiNi_xMn_2−xO₄, x = 0.1, 0.2, 0.3, 0.4, and 0.5) were synthesized by a spray-drying method and showed a single-phase spinel structure without any impurity. The amount of Ni has a large effect on the electrochemical characteristics. Capacity values of different voltage ranges (4- and 5-V ranges) change obviously with amount of Ni-doped. Also, the total discharge capacities increase with the Ni content, and all of them have good cycle stability.     

Properties of Ni1−xFex (0.1 < x < 0.9) and Invar (x = 0.64) alloys obtained by electrodeposition

Electrodeposition of Ni_1−xFe_x (x = 0.1-0.9) films was carried out from a chloride plating solution containing saccharin as an organic additive at a constant current density (5 mA/cm²) and a controlled pH of 2.5. X-ray diffraction studies revealed the existence of an fcc, or γ phase, in the range of 10-58 wt.% Fe, a mixed fcc/bcc phase in the range of 59-60 wt.% Fe, and a bcc, or α phase in the range of 64-90 wt.% Fe. The saturation magnetization, B_s, of electrodeposited Ni_1−xFe_x alloys at the room temperature was found to increase with the increase of Fe-content and follows the Slater-Pauling curve, but deviates from as-cast bulk NiFe alloys. The coefficient of thermal expansion, CTE, of electrodeposited alloys at room temperature also deviates from as-cast bulk NiFe alloys. Annealing of α-Ni₃₆Fe₆₄ alloy results in a martensitic α → γ phase transformation, which takes place between 300 and 400 °C. It was demonstrated that thermal treatment above 400 °C was necessary to obtain magnetic and mechanical properties similar to those to conventional Invar alloy. Annealing of α-Ni₃₆Fe₆₄ alloy at 700 °C brings about a decrease of B_s from 1.75 to 0.45 T. By controlling the annealing conditions of α → γ martensitic transformation, it is possible to adjust the CTE of Ni₃₆Fe₆₄ alloy over the broad limits from 2.7 to 8.7 × 10⁻⁶/°C.     

Stress evolution in CoxFe1−x (x = 0.33-0.87) electrodeposited films

Electrodeposition of 0.5 μm thick Co_xFe_1−x (x = 0.33-0.87) films was carried out from a sulfate/chloride plating solution containing saccharin as an organic additive at constant current density and a controlled pH 2.3. The increase of Fe²⁺ concentrations in plating solution resulted in an increase of Fe-content and tensile stress in Co_xFe_1−x films, which is accompanied by a decrease of plating rate. Several possible origins for generation of tensile stress include the following: interfacial stress between CoFe films and Cu-substrate, crystal texture and grain size, coalescence and stress evolution during film growth, and hydrogen adsorption/desorption. The adsorption/desorption mechanism of hydrogen seems to be the most likely dominant stress mechanism. The relationship between increase of the tensile stress and decrease of plating rate was discussed.     

Zr-doped Li[Ni0.5−xMn0.5−xZr2x]O2 (x = 0, 0.025) as cathode material for lithium ion batteries

Layered Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) have been prepared by the mixed hydroxide and molten-salt synthesis method. The individual particles of synthesized materials have a sub-microsize range of 200-500 nm, and LiNi_0.475Mn_0.475Zr_0.05O₂ has a rougher surface than that of LiNi_0.5Mn_0.5O₂. The Li/Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) electrodes were cycled between 4.5 and 2.0 V at a current density of 15 mA/g, the discharge capacity of both cells increased during the first ten cycles. The discharge capacity of the Li/LiNi_0.475Mn_0.475Zr_0.05O₂ cell increased from 150 to 220 mAh/g, which is 50 mAh/g larger than that of the Li/LiNi_0.5Mn_0.5O₂ cell. We found that the oxidation of oxygen and the Mn³⁺ ion concerned this phenomenon from the cyclic voltammetry (CV). Thermal stability of the charged Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) cathode was improved by Zr doping.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Characterization of MgxM2 − xP2O7 (M = Cu and Ni) solid solutions

In this study, Mg_xM_2 − xP₂O₇ (M = Cu, Ni; 0 ≤ x ≤ 2) and Mg_3 − yNi_y(PO₄)₂ (0 ≤ y ≤ 3) compositions were synthesized by the chemical coprecipitation method and characterized by X-ray diffraction, UV-vis-NIR spectroscopy and CIE L* a* b* (Commission Internationale de l’Eclairage L* a* b*) parameters measurements.Solid solutions with α-Cu₂P₂O₇ and α-Ni₂P₂O₇ structures and solid solutions with Ni₃(PO₄)₂ structure were obtained from diphosphate and orthophosphate compositions respectively. Isostructurality of α-Ni₂P₂O₇ and α-Mg₂P₂O₇ structures enlarges the compositional range of solid solution formation respect to the Mg_xCu_2 − xP₂O₇ solid solutions one.The CIE L* a* b* parameters in Mg_xNi_2 − xP₂O₇ samples were obtained comparable with these parameters in others yellow materials suitable for ceramic pigments. Mg_0.5Ni_1.5P₂O₇ composition fired at 800 °C or 1000 °C is the optimal composition to obtain yellow materials with α-diphosphate structure in conditions of this study.     

Improved electrochemical properties of Li1+x(Ni0.3Co0.4Mn0.3)O2−δ (x = 0, 0.03 and 0.06) with lithium excess composition prepared by a spray drying method

Layered Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ (x = 0, 0.03 and 0.06) materials were synthesized through the different calcination times using the spray-dried precursor with the molar ratio of Li/Me = 1.25 (Me = transition metals). The physical and electrochemical properties of the lithium excess and the stoichiometric materials were examined using XRD, AAS, BET and galvanostatic electrochemical method. As results, the lithium excess Li_1.06(Ni_0.3Co_0.4Mn_0.3)O_2−δ could show better electrochemical properties, such as discharge capacity, capacity retention and C rate ability, than those of the stoichiometric Li_1.00(Ni_0.3Co_0.4Mn_0.3)O_2−δ. In this paper, the effect of excess lithium on the electrochemical properties of Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ materials will be discussed based on the experimental results of ex situ X-ray diffraction, transmission electron microscopy (TEM) and galvanostatic intermittent titration technique (GITT)     

Electrochemical properties of La1−xSrxFeO3 (x = 0.2, 0.4) as negative electrode of Ni-MH batteries

La_(1−x)Sr_xFeO₃ (x = 0.2,0.4) powders were prepared by a stearic acid combustion method, and their phase structure and electrochemical properties were investigated systematically. X-ray diffraction (XRD) analysis shows that La_(1−x)Sr_xFeO₃ perovskite-type oxides consist of single-phase orthorhombic structure (x = 0.2) and rhombohedral one (x = 0.4), respectively. The electrochemical test shows that the reaction at La_(1−x)Sr_xFeO₃ oxide electrodes are reversible. The discharge capacities of La_(1−x)Sr_xFeO₃ oxide electrodes increase as the temperature rises. With the increase of the temperature from 298 K to 333 K, their initial discharge capacity mounts up from 324.4 mA h g⁻¹ to 543.0 mA h g⁻¹ (when x = 0.2) and from 147.0 mA h g⁻¹ to 501.5 mA h g⁻¹ (when x = 0.4) at the current density of 31.25 mA g⁻¹, respectively. After 20 charge-discharge cycles, they still remain perovskite-type structure. Being similar to the relationship between the discharge capacity and the temperature, the electrochemical kinetic analysis indicates that the exchange current density and proton diffusion coefficient of La_(1−x)Sr_xFeO₃ oxide electrodes increase with the increase of the temperature. Compared with La_0.8Sr_0.2FeO₃, La_0.6Sr_0.4FeO₃ electrode is a more promising candidate for electrochemical hydrogen storage because of its higher cycle capacity at various temperatures.     

Structural and magnetic properties of NiFe2−xBixO4 (x = 0, 0.1, 0.15) nanoparticles prepared via sol-gel method

NiFe_2−xBi_xO₄ (x = 0, 0.1, 0.15) nanopowders were synthesized via sol-gel method. The precursor gels were calcined at 773 K in air for 1 h to obtain the pure nanostructured NiFe_2−xBi_xO₄ spinel phase. The crystal structure and magnetic properties of the substituted spinel series of NiFe_2−xBi_xO₄ have been investigated by means of ⁵⁷Fe Mössbauer spectroscopy, transmission electron microscopy and alternating gradient force magnetometry. Mössbauer spectroscopic measurements revealed that Bi³⁺ cations tend to occupy octahedral positions in the structure of the substituted ferrite, i.e., the crystal-chemical formula of the as-prepared nanoparticles may be written as: (Fe)[NiFe_1−xBi_x]O₄ (x = 0, 0.1, 0.15), where parentheses and square brackets enclose cations on sites of tetrahedral and octahedral coordination, respectively. Selective area electron diffraction studies provided evidence that the samples of the NiFe_2−xBi_xO₄ series, independently of x, exhibit the cubic spinel structure. The values of the saturation magnetization and the coercive field of NiFe_2−xBi_xO₄ nanoparticles were found to decrease with increasing degree of bismuth substitution.     

Perovskite-type La2−xSrxNiO4 (0 ≤ x ≤ 1) as active anode materials for methanol oxidation in alkaline solutions

Perovskite-type ternary oxides with molecular formulae, La_2−xSr_xNiO₄ (0 ≤ x ≤ 1), were prepared by a modified citric acid sol-gel route at 600 °C for their possible use in a direct methanol fuel cell (DMFC). The study was conducted by cyclic voltammetry, chronoamperometry, impedance and anodic Tafel polarization techniques. The results showed that the electrocatalytic activity of the base oxide (x = 0) in 1 M KOH plus 1 M CH₃OH at 25 °C increases with x, the observed current densities being 23.6, 47.3, 43.2 and 50.9 mA cm⁻² at a scan rate of 10 mV s⁻¹ and E = 0.6 V versus Hg/HgO for oxides with x = 0, 0.25, 0.5 and 1.0, respectively. All the four perovskite anodes used in this study did not indicate any poisoning by the methanol oxidation intermediates/products. The methanol electro-oxidation reaction followed a Tafel slope of ∼2 × 2.303RT/3F (=40 mV decade⁻¹) on each oxide catalyst, regardless of Sr content.     

Assessment of Ba0.5Sr0.5Co1−yFeyO3−δ (y = 0.0-1.0) for prospective application as cathode for IT-SOFCs or oxygen permeating membrane

The influence of iron doping level in Ba_0.5Sr_0.5Co_1−yFe_yO_3−δ (y = 0.0-1.0) (BSCF) oxides on their phase structure, oxygen nonstoichiometry, electrical conductivity, performance as symmetrical cell electrode and oxygen permeating membranes was systematically investigated. A cubic perovskite structure was observed for all the compositions with the presence of iron. The increase of iron doping level resulted in the decrease of the lattice constant, room-temperature oxygen nonstoichiometry, total electrical conductivity, and the increase of area specific resistance (ASR) as cathode with samaria doped ceria electrolyte. However, promising cathode performance with an ASR as low as 0.613 Ω cm² was still obtained at 600 °C for Ba_0.5Sr_0.5FeO_3−δ (BSF). The ceramic membranes composing of BSCF with various iron doping level are all oxygen semi-permeable at elevated temperatures. The increase of iron doping level resulted in the decrease of oxygen permeation flux from JO₂ = 2.28 μmol cm⁻² s⁻¹ (STP) for Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCF5582) to ∼0.45 μmol cm⁻² s⁻¹ (STP) at 900 °C for BSF (y = 1.0) with the same membrane thickness of 1.1 mm, alongside with the change of the rate-determination step from the oxygen surface exchange to the slow oxygen bulk diffusion. The formation of composite oxide with a proper electronic conducting phase and the thin film technology are important for their prospective application as cathode in IT-SOFCs and oxygen permeating membrane, respectively.     

Double channel electrode flow cell application to the study of HO2 production on MnxCo3−xO4 (0 ≤ x ≤ 1) spinel films

We conducted a study on the electroreduction of O₂ in alkaline solution at room temperature on pure thin oxide electrodes of composition Mn_xCo_3−xO₄ (0 ≤ x ≤ 1) using the double channel electrode flow cell (DCEFC). The oxides were prepared at 150 °C and deposited by spray pyrolysis onto titanium substrates. The oxygen reduction reaction (orr) occurs through “interactive” and “parallel” pathways, and the ratio of O₂ molecules reduced to OH⁻ ions with respect to those reduced to HO₂⁻ ions depends on the oxide stoichiometry and on the applied overpotential. The formation of HO₂⁻ increases when the manganese concentration increases. The results obtained for the orr show that the number of electrons transferred per O₂ molecule decreases from 3 to 2 and the ratio k₁/k₂ (the rate constants for direct reduction to OH⁻ and indirect reduction to HO₂⁻) increases, respectively, in the overpotential studied range (−0.05 to −0.6 V). The Mn³⁺ ions placed in the B-sites of the spinel structure seem to be the active centres, where hydrogen peroxide is formed.     

Low temperature electrochemical properties of LaNi4.6−xMn0.4Mx (M = Fe or Co) and effect of oxide layer on EIS responses in metal hydride electrodes

Iron is a key element in the development of Co-free AB₅-type hydrogen storage alloys. The aim of this work is to systematically investigate the effects of Fe and Co on the electrochemical properties of LaNi_4.6−xMn_0.4M_x (M = Fe or Co, x = 0, 0.25, 0.5 and 0.75) hydrogen storage alloys under relatively low temperatures (273, 253 and 233 K). The results showed that substitution of Fe for Ni reduced the low temperature electrochemical performance much more seriously than that of Co. Exchange current density (I₀), charge-transfer resistance (R_ct) and hydrogen diffusion coefficient (D) were determined based on the study of linear polarization, electrochemical impedance spectrum (EIS) and galvanostatic discharge, respectively. Both the hydrogen diffusion in the bulk of alloy particles and the electrochemical reaction at the alloy electrolyte interface were found to be greatly limited as the decrease of temperature. During the EIS analysis, interestingly, we found that the semicircle in the high frequency region increased dramatically with the decrease of temperature. The electrochemical process corresponding to this semicircle was proposed to be related to the oxide layer on the surface of alloy particles. Novel explanations of EIS response in metal hydride electrodes were proposed accordingly.