Effect of hydrodynamic conditions on the inhibition performance of l-methionine as a “green” inhibitor

Influence of hydrodynamic conditions on the behavior of l-methionine (l-MTI) as a green organic inhibitor was studied using mild steel rotating disc electrode. Electrochemical impedance spectroscopy (EIS) and polarization measurements were carried out in the absence and presence of inhibitor in 1 M H₂SO₄ solution under static conditions and at different rotation speeds; the inhibitor concentration was 5 × 10⁻³ M in all tests. The open circuit potentials (OCP) were measured versus time in all studied rotation speeds; it was found that the OCP shifted toward more positive potentials as the rotation speed increased. It was also found that the inhibition efficiencies for still electrode and low speed rotations did not have noticeable changes, but in much higher rotation speeds, increased efficiencies were observed. This behavior could be attributed to the enhanced mass transport of inhibitor molecules from bulk to the metal surface in high rotation rates.     

Electrochemical reduction of Zn(II) ions on l-cysteine coated gold electrodes

Zn(II) ions have been selectively bound to the l-cysteine coated gold electrode in the form of a four-coordinated complex. Voltammograms of the Zn complex on the l-cysteine coated gold electrode showed a cathodic wave at ca. 0.05 V in the pH 7.54 phosphate buffered saline. The charge transfer coefficient and rate constant for the reduction of this Zn complex were 0.65 and 0.003 s⁻¹, respectively. The complexation of Zn(II) ions with l-cysteine on the gold electrode resulted in the maximum surface coverage of the Zn complex of 0.35 nmol cm⁻² and the Gibbs energy change of −27.6 kJ mol⁻¹. The cathodic peak current, influenced by the types of the end functional groups in thiols, the preconcentration time, and pH values of the supporting electrolyte, was linear with the concentration of Zn(II) ions in the range of 5.0 nM to 5 μM with a detection limit of 2.1 nM. The proposed voltammetric method was utilized successfully to detect the concentration of Zn(II) ions in hairs.     

Electrocatalytic oxidation of some amino acids on a nickel-curcumin complex modified glassy carbon electrode

This study investigated the electrocatalytic oxidation of alanine, l-arginine, l-phenylalanine, l-lysine and glycine on poly-Ni(II)-curcumin film (curcumin: 1,7-bis [4-hydroxy-3-methoxy phenyl]-1,6-heptadiene-3,5-dione) electrodeposited on a glassy carbon electrode in alkaline solution. The process of oxidation and its kinetics were established by using cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy techniques. Voltammetric studies indicated that in the presence of amino acids the anodic peak current of low valence nickel species increased, followed by a decrease in the corresponding cathodic current. This indicates that amino acids were oxidized on the redox mediator which was immobilized on the electrode surface via an electrocatalytic mechanism. Using Laviron's equation, the values of α and k_s for the immobilized redox species were determined as 0.43 ± 0.03 and 2.47 ± 0.02 × 10⁶ s⁻¹, respectively. The rate constant, the electron transfer coefficient and the diffusion coefficients involved in the electrocatalytic oxidation of amino acids were determined.     

Towards the conception of an amperometric sensor of l-tyrosine based on Hemin/PAMAM/MWCNT modified glassy carbon electrode

A novel amperometric sensor was fabricated based on the immobilization of hemin onto the poly (amidoamine)/multi-walled carbon nanotube (PAMAM/MWCNT) nanocomposite film modified glassy carbon electrode (GCE). Electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and ultraviolet visible (UV-vis) adsorption spectroscopy were used to investigate the possible state and electrochemical activity of the immobilized hemin. In the Hemin/PAMAM/MWCNT nanocomposite film, MWCNT layer possessed excellent inherent conductivity to enhance the electron transfer rate, while the layer of PAMAM greatly enlarged the surface average concentration of hemin (Γ) on the modified electrode. Therefore, the nanocomposite film showed enhanced electrocatalytical activity towards the oxidation of l-tyrosine. The kinetic parameters of the modified electrode were investigated. In pH 7.0 phosphate buffer solution (PBS), the sensor exhibits a wide linear range from 0.1 μM to 28.8 μM l-tyrosine with a detection limit of 0.01 μM and a high sensitivity of 0.31 μA μM⁻¹ cm⁻². In addition, the response time of the l-tyrosine sensor is less than 5 s. The excellent performance of the sensor is largely attributed to the electro-generated high reactive oxoiron (IV) porphyrin (O = Fe^IV-P) which effectively catalyzed the oxidation of l-tyrosine. A mechanism was herein proposed for the catalytic oxidation of l-tyrosine by oxoiron (IV) porphyrin complexes.     

A novel DNA biosensor based on ssDNA/Cyt c/l-Cys/GNPs/Chits/GCE

A novel DNA biosensor was fabricated by modified multilayer of ssDNA, cytochrome c, l-cysteine, metal gold nanoparticles and Chitosan (denoted as ssDNA/Cyt c/l-Cys/GNPs/Chits/GCE). The behavior of the DNA biosensor was then investigated by voltammetry, impedance spectrum and atomic force microscope (AFM), and the morphologic differences among each layer of the DNA biosensor were also observed. Results revealed that two well-defined redox peaks exhibited at 0.120 V and 0.362 V, and the amount of adsorbed DNA was 1.672 × 10⁻¹⁰ mol cm⁻². We concluded that the modified electrode could be used to detect DNA with the indicator daunomycin.     

Electrochemical detection of l-cysteine using a boron-doped carbon nanotube-modified electrode

A boron-doped carbon nanotube (BCNT)-modified glassy carbon (GC) electrode was constructed for the detection of l-cysteine (L-CySH). The electrochemical behavior of BCNTs in response to l-cysteine oxidation was investigated. The response current of L-CySH oxidation at the BCNT/GC electrode was obviously higher than that at the bare GC electrode or the CNT/GC electrode. This finding may be ascribed to the excellent electrochemical properties of the BCNT/GC electrode. Moreover, on the basis of this finding, a determination of L-CySH at the BCNT/GC electrode was carried out. The effects of pH, scan rate and interferents on the response of L-CySH oxidation were investigated. Under the optimum experimental conditions, the detection response for L-CySH on the BCNT/GC electrode was fast (within 7 s). It was found to be linear from 7.8 × 10⁻⁷ to 2 × 10⁻⁴ M (r = 0.998), with a high sensitivity of 25.3 ± 1.2 nA mM⁻¹ and a low detection limit of 0.26 ± 0.01 μM. The BCNT/GC electrode exhibited high stability and good resistance against interference by other oxidizable amino acids (tryptophan and tyrosine).     

Crystallization behavior of linear 1-arm and 2-arm poly(l-lactide)s: Effects of coinitiators

Linear 1-arm and 2-arm poly(l-lactide) [i.e., poly(l-lactic acid) (PLLA)] polymers having relatively low number-average molecular weights (M_n) (≤5 × 10⁴ g mol⁻¹) were synthesized by ring-opening polymerization of l-lactide initiated with tin(II) 2-ethylhexanoate (i.e., stannous octoate) and coinitiators of l-lactic acid, 1-dodecanol (i.e., lauryl alcohol), and ethylene glycol (these PLLA polymers are abbreviated as LA, DN, and EG, respectively). For M_n below 1.5 × 10⁴ g mol⁻¹, non-isothermal crystallization during heating and isothermal spherulite growth were disturbed in linear 2-arm PLLA (EG) compared to those in linear 1-arm PLLA (LA and DN). This finding indicates that the chain directional change, the incorporation of the coinitiator moiety as an impurity in the middle of the molecule, and their mixed effect disturbed the crystallization of linear 2-arm PLLA compared to that of linear 1-arm PLLA, in which the chain direction is unvaried and the coinitiator moiety is incorporated in the chain terminal. Also, the finding strongly suggests that the reported low crystallizability of multi-arm PLLA (arm number ≥ 3) compared to that of linear 1-arm PLLA is caused not only by the presence of branching points but also by the chain directional change, the incorporation of the coinitiator moiety in the middle of the molecule, and their mixed effect. The effects of the chain directional change and the position of the incorporated coinitiator moiety on the crystallization and physical properties of linear 1-arm and 2-arm PLLA decreased with an increase in M_n.     

Self-assembled monolayers (SAMs) of cobalt tetracarboxylic acidchloride phthalocyanine covalently attached onto a preformed mercaptoethanol SAM: A novel method

A feasible method of fabricating phthalocyanine sensor was developed by covalent attachment of cobalt tetracarboxylic acidchloride phthalocyanine (CoTCACIPc) onto a preformed 2-mercaptoethanol (2-ME) self-assembled monolayer (SAM) modified gold electrode (designated as CoTCACIPc-2-ME-SAM). The surface concentration of the CoTCACIPc was found to be 4.58 × 10⁻¹⁰ mol/cm². The sensor gave a linear response to l-cysteine over the concentration range 0.28-20 μM with a detection limit of 5 × 10⁻⁷ M and best response time of 2 s.     

Glass transition behavior and dynamic fragility in polylactides containing mobile and rigid amorphous fractions

The segmental dynamics of polylactide chains covering the T_g − 30 °C to T_g + 30 °C range was studied in absence and presence of a crystalline phase by dynamic mechanical analysis (DMA) using the framework provided by the WLF theory and the Angell's dynamic fragility concept. An appropriate selection of stereoisomers combined with a thermal conditioning strategy to promote crystallization (above T_g) or relaxation of chains (below T_g) was revealed as an efficient method to tune the ratio of the rigid and mobile amorphous phases in polylactides. A single bulklike mobile amorphous phase was taken for poly(d,l-lactide) (PDLLA). In turn three phases, comprising a mobile amorphous fraction (MAF, X_MA), a rigid amorphous fraction (RAF, X_RA) and a crystalline fraction (X_c) were determined in poly(l-lactide) (PLLA) by modulated differential scanning calorimetry (MDSC) according to a three-phase model. The analysis of results confirms that crystallinity and RAF not only elevate the T_g and the breadth of the glass transition region but also yields an increase in dynamic fragility parameter (m) which entails the existence of a smaller length-scale of cooperativity of polylactide chains in confined environments. Consequently it is proposed that crystallinity is acting in polymeric systems as a topological constraint that, preventing longer range dynamics, provides a faster segmental dynamics by the temperature dependence of relaxation times according to the strong-fragile scheme.     

Detection of NADH via electrocatalytic oxidation at single-walled carbon nanotubes modified with Variamine blue

Screen-printed electrodes (SPEs) modified with Variamine blue (VB), covalently attached to the oxidized single-walled carbon nanotubes (SWCNTs-COOH), were developed and used as chemical sensors for the detection of the reduced nicotinamide adenine dinucleotide (NADH). The Variamine blue redox mediator was covalently linked to the SWCNTs-COOH by the N,N′-dicyclohexylcarbodiimide (DCC) and N-hydroxysuccinimide (NHS) chemistry. Infrared Fourier transform (FT-IR) spectroscopy revealed the presence of the amide bands situated at 1623 cm⁻¹ (I band), 1577 cm⁻¹ (II band) and 1437 cm⁻¹ (III band) demonstrating the covalent linkage of Variamine blue to SWCNTs-COOH. The heterogeneous electron transfer rate, k_obs., was 13,850 M⁻¹ s⁻¹, and the k_s and α were 0.8 s⁻¹ and 0.56, respectively. The pH dependence was also investigated. SPEs modified with Variamine blue by using the DCC/NHS conjugation method, showed a variation of −36 mV per pH unit.A successful application was the development of a lactate biosensor obtained by the immobilization of the l-lactate dehydrogenase on the NADH sensor.     

Spherulite growth of l-lactide copolymers: Effects of tacticity and comonomers

The spherulite growth behavior and mechanism of l-lactide copolymers, poly(l-lactide-co-d-lactide) [P(LLA-DLA)], poly(l-lactide-co-glycolide) [P(LLA-GA)], and poly(l-lactide-co-ε-caprolactone) [P(LLA-CL)] have been studied using polarization optical microscopy in comparison with poly(l-lactide) (PLLA) having different molecular weights to elucidate the effects of incorporated comonomer units. The incorporation of comonomer units reduced the radius growth rate of spherulites (G) and increased the induction period of spherulite formation (t_i), irrespective of the kind of comonomer unit. Such effects became remarkable with the content of comonomers. At a crystallization temperature (T_c) of 130 °C, the disturbance effects of comonomers on the spherulite growth decreased in the following order: d-lactide>glycolide>ε-caprolactone, when compared at the same comonomer unit or reciprocal of averaged l-lactyl unit sequence length (l_l). The t_i estimation indicated that the glycolide units have the lowest disturbance effects on the formation of spherulite (crystallite) nuclei. The PLLA having the number-average molecular weight (M_n) exceeding 3.1×10⁴ g mol⁻¹ showed the transition from regime II to regime III at T_c=120 °C, whereas PLLA with the lowest M_n of 9.2×10³ g mol⁻¹ crystallized solely in regime III kinetics and the copolymers excluding P(LLA-DLA) with 3% of d-lactide units crystallized solely according to regime II kinetics. The nucleation and front constant for regime II and III [K_g(II), K_g(III), G₀(II), and G₀(III), respectively] estimated with each (not with a fixed for high-molecular-weight PLLA) decreased with increasing the amount of defects per unit mass of the polymer for crystallization, i.e. with increasing the comonomer content and the density of terminal group through decreasing the molecular weight.     

A DNA electrochemical sensor with poly-l-lysine/single-walled carbon nanotubes films and its application for the highly sensitive EIS detection of PAT gene fragment and PCR amplification of NOS gene

A sensitive and novel DNA electrochemical biosensor for the detection of the transgenic plants gene fragment by electrochemical impedance spectroscopy (EIS) was presented. The well-dispersed carboxylic group-functionalized single-walled carbon nanotubes (SWNTs) were dripped onto the carbon paste electrode (CPE) surface firstly, and poly-l-lysine films (pLys) were subsequently electropolymerized by cyclic voltammetry (CV) to prepare pLys/SWNTs/CPE. The morphology of pLys/SWNTs films was examined using a field emission scanning electron microscope (SEM). The pLys/SWNTs films modified electrode exhibited very good conductivity. DNA probes were easily immobilized on the poly-l-lysine films via electrostatic adsorption. The hybridization events were monitored with electrochemical impedance spectroscopy using [Fe(CN)₆]^3−/4− as indicator. The PAT gene fragment from phosphinothricin acetyltransferase gene was detected by this DNA electrochemical sensor. The dynamic detection range of this sensor to the PAT gene fragment was from 1.0 × 10⁻¹² to 1.0 × 10⁻⁷ mol/L. A detection limit of 3.1 × 10⁻¹³ mol/L could be estimated. The PCR amplification of NOS gene from the sample of a kind of transgenic modified bean was also detected satisfactorily by EIS.     

Amperometric glutamate biosensor based on chitosan enzyme film

A simple method for enzyme immobilization in electrochemical biosensors for monosodium glutamate (MSG) was developed. The method relied on the precipitation of complexes of polyanionic enzyme l-glutamate oxidase (GmOx) with polycationic chains of chitosan (CHIT) on the surface of platinum electrode. Such ionotropic gelation allowed the CHIT matrix to retain ∼57% of applied GmOx (0.30-3.0 units). The CHIT + GmOx based biosensor displayed a low detection limit of 1.0 × 10⁻⁷ M MSG (S/N = 3, E = 0.400 V), linear range up to 2 × 10⁻⁴ M (R² = 0.991), sensitivity of 85 mA M⁻¹ cm⁻², and a short response time (t_90% = 2 s). The biosensors maintained ∼80% of the MSG signal even after 11 h of continuous use, which indicated good operational stability. Stability studies revealed that a majority of signal loss was due to a slow transformation of glutamate in a solution into the redox inactive pyroglutamate. After 4 months of storage in water at 4 °C, the CHIT + GmOx films retained ∼80-90% of their original activity toward the MSG. The CHIT + GmOx films are promising candidates for the development of simple and reliable chromatographic detectors for glutamate.     

Electrochemically oxidized carbon anode in direct l-ascorbic acid fuel cells

The activity of electrochemically oxidized carbon electrode was investigated in the operation of a direct l-ascorbic acid fuel cell anode. The surface oxygen species placed on electrochemically oxidized carbon electrode were analyzed by X-ray photoelectron spectroscopy and cyclic voltammetry. The electrochemical oxidation process of carbon electrode can facilitate the pore-filling process (i.e., wetting) of the electrolyte into the microstructure of the carbon electrode by increasing the number of more polar functional groups on the electrode surface. The electrochemically oxidized carbon electrode exhibited significantly enhanced electro-catalytic oxidation activity of l-ascorbic acid compared to an unmodified carbon electrode. Moreover, the simplified electrode structure using carbon paper without an additional powder-based precious catalyst layer is very favorable in creating percolation network and generates power density of 18 mW/cm² at 60 °C.     

Ring-opening polymerization of six-membered cyclic esters catalyzed by tetrahydroborate complexes of rare earth metals

Catalytic behavior of tetrahydroborate complexes of rare earth metals, Ln(BH₄)₃(THF)_x (1: Ln = La, x = 3; 2: Ln = Pr, x = 2; 3: Ln = Nd, x = 3; 4: Ln = Sm, x = 3; 5: Ln = Y, x = 2.5; 6: Ln = Yb, x = 3), for ring-opening polymerization (ROP) of six-membered cyclic esters, δ-valerolactone (VL) and d,l-lactide (d,l-LA), was studied. The controlled polymerization of VL with 1-6 proceeded in THF at 60 °C. The catalytic activities of these complexes for the ROP of VL were observed to be in order of the ionic radii of the metals: 1(La) ≥ 2(Pr) ≥ 3(Nd) > 4(Sm) > 5(Y) > 6(Yb). The obtained polymers were demonstrated to be hydroxy-telechelic by ¹H NMR and MALDI-TOF MS spectroscopy. The controlled ROP of d,l-LA also proceeded by these complexes. The activities of these complexes for the d,l-LA ROP were also in order of the ionic radii of the metals.     

Raman microspectroscopy study of structure, dispersibility, and crystallinity of poly(hydroxybutyrate)/poly(l-lactic acid) blends

The structure, dispersibility, and crystallinity of poly(3-hydroxybutyrate) (PHB) and poly(l-lactic acid) (PLLA) blends are investigated by using Raman microspectroscopy. Four kinds of PHB/PLLA blends with a PLLA content of 20, 40, 60, and 80 wt% were prepared from chloroform solutions. Differences in the Raman microspectroscopic spectra between the spherulitic and nonspherulitic parts in the blends mainly lie in the CO stretching band and C-O-C and C-C skeletal stretching bands of PHB and PLLA. In addition to such bands, the Raman spectra of spherulitic structure in the blends show a band due to the CH₃ asymmetric stretching mode at an unusually high frequency (3009 cm⁻¹), suggesting the existence of a C-H?OC hydrogen bond of PHB in the spherulite. The existence of C-H?OC hydrogen bond is one of the unambiguous evidence for the crystallization of PHB component in the blends. Therefore, it is possible to distinguish Raman bands due to each component in the spectra of blends. Raman spectra of the spherulitic structure in the blends are similar to a Raman spectrum of pure crystalline PHB, while those of the nonspherulitic parts in the blends have each component peak of PHB and PLLA. The present study reveals that the PHB component is crystallized in the blends irrespective of the blend ratio, and that both components are mixed in the nonspherulite parts. The crystalline structure of PHB and the nonspherulitic parts of PLLA in the blends are characterized, respectively, by the unique band of C-H?OC hydrogen bond at 3009 cm⁻¹ and CCO deformation bands near 400 cm⁻¹.     

Facile direct electron transfer in glucose oxidase modified electrodes

Glucose oxidase (GOx) is widely used in the glucose biosensor industry. However, mediatorless direct electron transfer (DET) from GOx to electrode surfaces is very slow. Recently, mediatorless DET has been reported via the incorporation of nanomaterials such as carbon nanotubes and nanoparticles in the modification of electrodes. Here we report GOx electrodes showing DET without the need for any nanomaterials. The enzyme after immobilization with poly-l-lysine (PLL) and Nafion^® retains the biocatalytic activities and oxidizes glucose efficiently. The amperometric response of Nafion-PLL-GOx modified electrode is linearly proportional to the concentration of glucose up to 10 mM with a sensitivity of 0.75 μA/mM at a low detection potential (−0.460 V vs. Ag/AgCl). The methodology developed in this study will have impact on glucose biosensors and biofuel cells and may potentially simplify enzyme immobilization in other biosensing systems.     

Surface chemistry and electrocatalytic behaviour of tetra-carboxy substituted iron, cobalt and manganese phthalocyanine monolayers on gold electrode

Surface chemistry and electrocatalytic properties of self-assembled monolayers of metal tetra-carboxylic acid phthalocyanine complexes with cobalt (Co), iron (Fe) and manganese (Mn) as central metal ions have been studied. These phthalocyanine molecules are immobilized on gold electrode via the coupling reaction between the ring substituents and pre-formed mercaptoethanol self-assembled monolayer (Au-ME SAM). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy confirmed chemisorption of mercaptoethanol via sulfur group on gold electrode and also coupling reaction between phthalocyanines and Au-ME SAM. Electrochemical parameters of the immobilized molecules show that these molecules are densely packed with a perpendicular orientation. The potential applications of the gold modified electrodes were investigated towards l-cysteine detection and the analysis at phthalocyanine SAMs. Cobalt and iron tetra-carboxylic acid phthalocyanine monolayers showed good oxidation peak for l-cysteine at potentials where metal oxidation (M^III/M^II) takes place and this metal oxidation mediates the catalytic oxidation of l-cysteine. Manganese tetra-carboxylic acid phthalocyanine monolayer also exhibited a good catalytic oxidation peak towards l-cysteine at potentials where Mn^IV/Mn^III redox peak occurs and this redox peak mediates l-cysteine oxidation. The analysis of cysteine at phthalocyanine monolayers displayed good analytical parameters with good detection limits of the orders of 10⁻⁷ mol L⁻¹ and good linearity for a studied concentration range up to 60 μmol L⁻¹.     

pH affected migrational transport of ferrocene derivative of l-cysteine in aqueous solutions: Voltammetric studies

The mass transport of biologically-active l-cysteine derivatized with the ferrocenyl group (FcCH₂Cys) was investigated voltammetrically at a microelectrode in aqueous solutions under the conditions of varying content of supporting electrolyte and at different pH values. By varying the pH conditions one could obtain samples containing differently ionized forms of the l-cysteine derivative, from a monovalent cation via a neutral form (zwitterion) to a monovalent anion. Due to the acid-base equilibrium the obtained solutions were, in fact, mixtures composed predominantly of either anionic or cationic, or neutral species of FcCH₂Cys, respectively. Under the conditions of low ionic support the mass transport of these forms is differently affected by the migrational contribution. The results obtained experimentally were in good agreement with the theoretical predictions. In the calculations it was assumed that the FcCH₂Cys forms, coexisting in the solution, contribute independently to the steady-state transport-limited current. It was also assumed that the diffusion coefficients of the FcCH₂Cys forms were equal. This was validated by the voltammetric measurements at the supporting electrolyte excess (purely diffusional conditions). The diffusion coefficients of different forms of FcCH₂Cys are very similar and the average diffusion coefficient is (5.35 ± 0.05) × 10⁻¹⁰ m²/s.The studies clearly show that the variation in the conditions of pH or/and concentration of electrolyte can change the transport rate of l-cysteine even by several tens percent.     

A-B-A-Triblock and multiblock copolyesters prepared from ε-caprolactone, glycolide and l-lactide by means of bismuth subsalicylate

Bismuth (III) subsalicylate, a commercial drug, was used as catalyst for 1,4-butanediol-initiated copolymerizations of ε-caprolactone (εCL) and glycolide (GL). Telechelic copolyesters having two OH-endgroups and predominantly alternating sequences were obtained. These copolyesters are amorphous with glass transition temperatures (T_gs) below −30 °C. In a second series of polymerizations, in situ chain extension with l-lactide (LLA) was performed, whereby A-B-A triblock copolymers were obtained without significant transesterification between A- and B-blocks. Finally, these A-B-A triblock copolymers were transformed into multiblock copolymers by chain extension with 1,6-hexamethylene diisocyanate. The block copolymers were characterized by ¹H and ¹³C NMR spectroscopy, by viscosity, SEC and DSC measurements.