Synthesis of sawtooth-like Li4Ti5O12 nanosheets as anode materials for Li-ion batteries

Hierarchical layered hydrous lithium titanate and Li₄Ti₅O₁₂ microspheres assembled by nanosheets have been successfully synthesized via a hydrothermal process and subsequent thermal treatment. The electrochemical properties of the two samples have been investigated by galvanostatic methods. The former, with the obvious layered structure and a large surface area, delivers a reversible capacity of 180 mA h g⁻¹ after 200 cycles at 200 mA g⁻¹. As for Li₄Ti₅O₁₂, with the intriguing and unique sawtooth-like morphology, it presents exceptional high rate performance and excellent cycling stability. Up to 132 mA h g⁻¹ is obtained after 200 cycles at 10,000 mA g⁻¹ (57 C), proving itself promising for high-rate applications.     

Li4Ti5O12 hollow microspheres assembled by nanosheets as an anode material for high-rate lithium ion batteries

In this paper, Li₄Ti₅O₁₂ (LTO) hollow microspheres with the shell consisting of nanosheets have been synthesized via a hydrothermal route and following calcination. Because of the favorable transport properties of this hollow structure, it is the rate performance at high current densities which is exceptional. When the LTO hollow microspheres were used as the anode material in lithium ion battery, they exhibited superior rate performance and high capacity even at a very high rate (131 mAh g⁻¹ at 50 C).     

Synthesis and electrochemical properties of Li2ZnTi3O8 fibers as an anode material for lithium-ion batteries

Li₂ZnTi₃O₈ fibers are synthesized by thermally treating electrospun Zn(CH₃COO)₂/LiOAc/TBT/PVP fibers and utilized as an energy storage material for rechargeable lithium-ion batteries. The material is characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and thermal analysis. Scanning electron microscopy results show that the Li₂ZnTi₃O₈ fibers have an average diameter of 200 nm. Electrochemical properties of the material are evaluated using cyclic voltammetry, galvanostatic cycling and electrochemical impedance spectroscopy. The results show that as-prepared Li₂ZnTi₃O₈ has a high specific discharge capacity of 227.6 mAh g⁻¹ at the 2nd cycle. Its electrochemical performance at subsequent cycles shows good cycling capacity and rate capability. The obtained results thus strongly support that the electrospinning method is an effective method to prepare Li₂ZnTi₃O₈ anode material with higher capacity and rate capability.     

Hematite nanoflakes as anode electrode materials for rechargeable lithium-ion batteries

Hematite (α-Fe₂O₃) nanoflakes and nanocubes were synthesized by liquid-solid-solution method and their properties as anode electrode materials for rechargeable Li⁺-ion batteries were measured. When changing the water to ethanol volume ratio in the synthesis system, the nanocrystals can be changed from α-Fe₂O₃ to α-FeOOH, with shapes being tuned from nanoflakes to nanocubes, non-uniform particles and nanowires. When assembled as the anode electrode materials in rechargeable Li⁺-ion batteries, the hematite nanoflakes showed one more plateau in the first discharge progress of the voltage-composition curves than hematite nanocrystals with other shapes in the literature. X-ray diffraction, high-resolution transmission electron microscope and electrochemical data showed that this extra plateau came from the formation of Li₂Fe₃O₄ nanoclusters and amorphous Li₂O. This experiment showed that like sizes, shapes of nanocrystals may also affect the detailed electrochemical progress.     

An investigation of polypyrrole-LiFePO4 composite cathode materials for lithium-ion batteries

A series of polypyrrole-LiFePO₄ (PPy-LiFePO₄) composites were synthesised by polymerising pyrrole monomers on the surface of LiFePO₄ particles. AC impedance measurements show that the coating of polypyrrole significantly decreases the charge-transfer resistance of LiFePO₄ electrodes. The electrochemical reactivity of polypyrrole and PPy-LiFePO₄ composites for lithium insertion and extraction was examined by charge/discharge testing. The PPy-LiFePO₄ composite electrodes demonstrated an increased reversible capacity and better cyclability, compared to the bare LiFePO₄ electrode.     

Preparation and characterization of three dimensionally ordered macroporous Li4Ti5O12 anode for lithium batteries

Three dimensionally ordered macroporous (3DOM) Li₄Ti₅O₁₂ membrane (80 μm thick) was prepared by a colloidal crystal templating process. Colloidal crystal consisting of monodisperse polystyrene particles (1 μm diameter) was used as the template for the preparation of macroporous Li₄Ti₅O₁₂. A precursor sol consisting of titanium isopropoxide and lithium acetate was impregnated into the void space of template, and it was calcined at various temperatures. A macroporous membrane of Li₄Ti₅O₁₂ with inverse-opal structure was successfully prepared at 800 °C. The interconnected pores with uniform size (0.8 μm) were clearly observed on the entire part of membrane. The electrochemical properties of the three dimensionally ordered Li₄Ti₅O₁₂ were characterized with cyclic voltammetry and galvanostatic charge and discharge in an organic electrolyte containing a lithium salt. The 3DOM Li₄Ti₅O₁₂ exhibited a discharge capacity of 160 mA h g⁻¹ at the electrode potential of 1.55 V versus Li/Li⁺ due to the solid state redox of Ti^3+/4+ accompanying with Li⁺ ion insertion and extraction. The discharge capacity was close to the theoretical capacity (167 mA h g⁻¹), which suggested that the Li⁺ ion insertion and extraction took place at the entire part of 3DOM Li₄Ti₅O₁₂ membrane. The 3DOM Li₄Ti₅O₁₂ electrode showed good cycle stability.     

Hydrothermal synthesis of Co3O4 microspheres as anode material for lithium-ion batteries

Co₃O₄ microspheres were synthesized in mass production by a simple hydrothermal treatment. One micrometer-sized spherical particles with well-crystallization could be obtained by XRD and SEM. Higher specific surface area (93.4 m² g⁻¹) and larger pore volume (78.4 cm³ g⁻¹) by BET measurements offered more interfacial bondings for extra sites of Li⁺ insertion, which resulted in the anomalous large initial irreversible capacity and capacity cycling loss due to SEI film formation. The capacity retention of Co₃O₄ microspheres involved first forming acted as Li-ion anode material is almost above 90% from 12th cycle and it retain lithium storage capacity of 550.2 mAh g⁻¹ after 25 cycles, which show good long-life stability. The electrochemical impedance spectroscopy (EIS) tests before and after cyclic voltammetry measurements and charge-discharge experiments were carried out and the corresponding D_Li values were also calculated. The relationship of the ac impedance spectra and the cycling behaviors was discussed. It is found that the decrease of capacity results from the larger Li⁺ charge-transfer impedance and the lower lithium-diffusion processes on cycling, which is in very good agreement with the electrochemical behaviors of Co₃O₄ electrode.     

Microstructure effect on the electrochemical property of Li4Ti5O12 as an anode material for lithium-ion batteries

Porous (P-) and dense (D-) lithium titanate (Li₄Ti₅O₁₂) powders as an anode material for lithium-ion batteries have been synthesized by spray drying followed by solid-state calcination. Electrochemical testing results showed that the discharge capacities of P-Li₄Ti₅O₁₂ are 144 mAh/g, 128 mAh/g and 73 mAh/g at the discharging rate of 2C, 5C and 20C, respectively (cut-off voltages: 0.5-2.5 V). The corresponding values for D-Li₄Ti₅O₁₂ are 108 mAh/g, 25 mAh/g and 17 mAh/g. The higher capacity of the P-Li₄Ti₅O₁₂ at high charge/discharge rates was attributed to the shorter transport path of Li ions and higher electronic conductivity in the P-Li₄Ti₅O₁₂ as a result of its smaller primary particle size and higher surface area compared with those of the D-Li₄Ti₅O₁₂.     

Electrochemical and spectroscopic characterization of lithium titanate spinel Li4Ti5O12

Herein we describe electrochemical and spectroscopic properties of lithium titanate spinel as well as an easy method based on colorimetry to determine the lithium content of electrodes containing lithium titanate spinel as active material. Raman microspectrometry measurements have been performed to follow lithium insertion into and extraction from the active material, respectively. The Raman signals display a pronounced fading of intensity already at low levels of lithium intercalation and disappear at a SOC higher than ∼10%. However, the colorimetric method can be used up to a SOC of 50%.     

Hydrothermal synthesis of flower-like Zn2SnO4 composites and their performance as anode materials for lithium-ion batteries

Flower-like Zn₂SnO₄ composites had been prepared through a green hydrothermal synthesis. The structural, morphological and electrochemical properties were investigated by means of XRD, BET, SEM, TEM, and electrochemical measurement. The results show that the as-prepared sample is in high purity phase and of good crystallinity; meanwhile it has a particular 3-D structure and large surface area. Electrochemical measurement suggests that flower-like Zn₂SnO₄ composites exhibit better cycling properties and lower initial irreversible capacities than the solid Zn₂SnO₄ cubes. The first discharge and charge capacities of the material are 1750 mA h g⁻¹ and 880 mA h g⁻¹ respectively. A higher reversible capacity of 501 mA h g⁻¹ was obtained after 50 cycles at a current density of 300 mA g⁻¹. The higher reversible capacity and good stability can be related to the special nanostructural features of the material. Such Zn₂SnO₄ structures synthesized by the simple and cheap method are expected to have potential application in energy storage.     

Large reversible capacity of high quality graphene sheets as an anode material for lithium-ion batteries

High quality graphene sheets were prepared from graphite powder through oxidation followed by rapid thermal expansion in nitrogen atmosphere. The preparation process was systematically investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy and Brunauer-Emmett-Teller (BET) measurements. The morphology and structure of graphene sheets were characterized by scanning electron microscope (SEM) and high-resolution transmission electron microscopy (HRTEM). The electrochemical performances were evaluated in coin-type cells versus metallic lithium. It is found that the graphene sheets possess a curled morphology consisting of a thin wrinkled paper-like structure, fewer layers (∼4 layers) and large specific surface area (492.5 m² g⁻¹). The first reversible specific capacity of the prepared graphene sheets was as high as 1264 mA h g⁻¹ at a current density of 100 mA g⁻¹. Even at a high current density of 500 mA g⁻¹, the reversible specific capacity remained at 718 mA h g⁻¹. After 40 cycles, the reversible capacity was still kept at 848 mA h g⁻¹ at the current density of 100 mA g⁻¹. These results indicate that the prepared high quality graphene sheets possess excellent electrochemical performances for lithium storage.     

Structural and electrochemical characteristics of Li4−xAlxTi5O12 as anode material for lithium-ion batteries

Al-doped Li₄Ti₅O₁₂ in the form of Li_4−xAl_xTi₅O₁₂ (x = 0, 0.05, 0.1 and 0.2) was synthesized via solid state reaction in an Ar-flowing atmosphere. Al-doping does not change the phase composition and particle morphology, but easily results in the lattice distortion and thus the poor crystallinity of Li₄Ti₅O₁₂. Al-doping decreases the specific capacity of Li₄Ti₅O₁₂, while improves remarkably its cycling stability at high charge/discharge rate. The substitution of Al for Li site can enhance the electronic conductivity of Li₄Ti₅O₁₂ via the generation of mixing Ti⁴⁺/Ti³⁺, whereas impede the Li-ion diffusion in the lattice. Excessive Al causes large electrode polarization due to the lower Li-ion conductivity, and thus leads to low specific capacity at high current densities. Li_3.9Al_0.1Ti₅O₁₂ exhibits a relatively high specific capacity and an excellent cycling stability.     

Hollow CuFe2O4 spheres encapsulated in carbon shells as an anode material for rechargeable lithium-ion batteries

We report here a polymer-templated hydrothermal growth method and subsequent calcination to achieve carbon coated hollow CuFe₂O₄ spheres (H–CuFe₂O₄@C). This material, when used as anode for Li-ion battery, retains a high specific capacity of 550 mAh g⁻¹ even after the 70th cycle, which is much higher than those of both CuFe₂O₄@C (∼300 mAh g⁻¹) and H–CuFe₂O₄ (∼120 mAh g⁻¹). And galvanostatic cycling at different current densities reveals that a capacity of 480 mAh g⁻¹, 91% recovery of the specific capacity cycling at 100 mA g⁻¹, can be obtained even after 50 cycles running from 100 to 1600 mA g⁻¹. The significantly enhanced electrochemical performances of H–CuFe₂O₄@C with regard to Li-ion storage are ascribed to the following factors: (1) the hollow void, which could mitigate the pulverization of electrode and facilitate the lithium-ion, electron and electrolyte transport; (2) the conductive carbon coating, which could enhance the conductivity, alleviate the agglomeration problem, prevent the formation of an overly thick SEI film and buffer the electrode. Such a structural motif of H–CuFe₂O₄@C is promising, for electrode materials of LIBs, and points out a general strategy for creating other hollow-shell electrode materials with improved electrochemical performances.     

Carbon-coated Bi5Nb3O15 as anode material in rechargeable batteries for enhanced lithium storage

Bismuth can alloy with lithium to generate Li₃Bi with the volumetric capacity of about 3765 mAh cm^?3 (386 mAh g^?1), rendering bismuth-based materials as attractive alloying-type electrode materials for rechargeable batteries. In this work, bismuth-based material Bi₅Nb₃O₁₅ @C is fabricated as anode material through a traditional solid-state reaction with glucose as carbon source. Bi₅Nb₃O₁₅ @C composite is well dispersed, with small particle size of 0.5–2.0?µm. The electrochemical performance of Bi₅Nb₃O₁₅ @C is reinforced by carbon-coated layer as desired. The Bi₅Nb₃O₁₅ @C exhibits a high specific capacity of 338.56 mAh g^?1 at a current density of 100?mA?g^?1. And it also presents an excellent cycling stability with a capacity of 212.06 mAh g^?1 over 100 cycles at 100?mA?g^?1. As a comparison, bulk Bi₅Nb₃O₁₅ without carbon-coating only remains 319.62 mAh g^?1 at 100?mA?g^?1, revealing poor cycle and rate performances. Furthermore, in-situ X-ray diffraction experiments investigate the alloying/dealloying behavior of Bi₅Nb₃O₁₅ @C. These insights will benefit the discovery of novel anode materials for lithium-ion batteries.     

SnO2-coated multiwall carbon nanotube composite anode materials for rechargeable lithium-ion batteries

SnO₂-coated multiwall carbon nanotube (MWCNT) nanocomposites were synthesized by a facile hydrothermal method. The as-prepared nanocomposites were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). The SnO₂/MWCNT composites, when combined with carboxymethyl cellulose (CMC) as a binder, show excellent cyclic retention, with the high specific capacity of 473 mAh g⁻¹ beyond 100 cycles, much greater than that of the bare SnO₂ which was also prepared by the hydrothermal method in the absence of MWCNTs. The enhanced capacity retention could be mainly attributed to good dispersion of the tin dioxide particles in the matrix of MWCNTs, which protected the particles from agglomeration during the cycling process. Furthermore, the usage of CMC as a binder is responsible for the low cost and environmental friendliness of the whole electrode fabrication process.     

Isothermal calorimetry investigation of Li1+xMn2−yAlzO4 spinel

The heat generation of LiMn₂O₄, Li_1.156Mn_1.844O₄, and Li_1.06Mn_1.89Al_0.05O₄ spinel cathode materials in a half-cell system was investigated by isothermal micro-calorimetry (IMC). The heat variations of the Li/LiMn₂O₄ cell during charging were attributed to the LiMn₂O₄ phase transition and order/disorder changes. This heat variation was largely suppressed when the stoichiometric spinel was doped with excess lithium or lithium and aluminum. The calculated entropy change (dE/dT) from the IMC confirmed that the order/disorder change of LiMn₂O₄, which occurs in the middle of the charge, was largely suppressed with lithium or lithium and aluminum doping. The dE/dT values obtained did not agree between the charge and the discharge at room temperature (25 °C), which was attributed to cell self-discharge. This discrepancy was not observed at low temperature (10 °C). Differential scanning calorimeter (DSC) results showed that the fully charged spinel with lithium doping has better thermal stability.     

Hydrothermal synthesis of Zn-doped Li4Ti5O12 with improved high rate properties for lithium ion batteries

Hydrothermal method has been successfully used to synthesize a spheroidic zinc doped Li₄Ti₅O₁₂ (Li_3.95Zn_0.05Ti₅O₁₂) with large specific surface area. X-ray diffraction (XRD) and scanning electron microscope (SEM) are used to characterize the structure and morphology. The electrochemical properties are measured by the galvanostatic method and the results demonstrate that the Li₄Ti_3.95Zn_0.05O₁₂ has a large discharge capacity of 182.45 mAh/g at 0.1C. With the favorable transport channel caused by the doped Zn²⁺, the Li_3.95Zn_0.05Ti₅O₁₂ exhibits an enhanced high rate capacity of 122.38 mAh/g and better cyclic stability at 10C, which is promising for application in lithium ion batteries.     

Graphene as a conductive additive to enhance the high-rate capabilities of electrospun Li4Ti5O12 for lithium-ion batteries

Spinel Li₄Ti₅O₁₂ (LTO) is a promising candidate anode material for Li-ion batteries due to its well-known zero-strain merits. To improve the electronic properties of spinel LTO, which are intrinsically poor, we processed the material into a nanosized architecture to shorten the distance for Li-ion and electron transport using the versatile electrospinning method. Graphene was chosen as an effective carbon coating to improve the surface conductivity of the nanocomposites. The as-prepared graphene-embedded LTO anode material showed improved discharging/charging and cycling properties, particularly at high rates, such as 22 C, which makes the nanocomposite an attractive anode material for applications in electric vehicles.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

Electrochemical properties of SnO2/carbon composite materials as anode material for lithium-ion batteries

SnO₂/carbon composite anode materials were synthesized from SnCl₄·5H₂O and sucrose via a hydrothermal route and a post heat-treatment. The synthesized spherical SnO₂/carbon powders show a cauliflower-like micro-sized structure. High annealing temperature results in partial reduction of SnO₂. Metallic Sn starts to emerge at 500 °C. High Sn content in SnO₂/carbon composite is favorable for the increase of initial coulombic efficiency but not for the cycling stability. The SnO₂/carbon annealed at 500 °C exhibits high specific capacity (∼400 mAh g⁻¹), stable cycling performance and good rate capability. The generation of Li₂O in the first lithiation process can prevent the aggregation of active Sn, while the carbon component can buffer the big volume change caused by lithiation/delithiation of active Sn. Both of them make contribution to the better cycle stability.