Synthesis and characterization of yttrium and antimony codoped SnO2 conductive nanoparticles

Y was used as a dopant in preparing conductive powder to improve its performance. Y and Sb co-doped SnO₂ conductive nanoparticles were prepared by the complexation-coprecipitation method with Sn, Sb₂O₃ and Y₂O₃ as the raw materials. Crystal phase, thermal behavior and structure of the prepared conductive nanoparticles were characterized by X-ray diffraction (XRD), thermal analysis (TG-DSC), Fourier transform infrared (FTIR) and transmission electron microscopy (TEM) techniques, respectively. The Y and Sb co-doped SnO₂ conductive nanoparticles with a structure of tetragonal rutile had intense absorption in 4000-2500 cm^?1, and the diameter ranged from 10 to 30 nm. The resistivity of Y and Sb co-doped SnO₂ conductive nanoparticles was as low as 0.09 Ω·cm which was 4.6 times lower than that of Sb doped SnO₂ conductive nanoparticles.     

Re-determination of the crystal structure of Ca₂Y₈Si₆O₂₆ and study on the luminescent properties of Ca₂Y₈Si₆O₂₆:Tb³⁺

The crystal structure of silicate oxyapatite Ca2Y8Si6O26 was indexed as hexagonal,space group P63/m,a=0.93515 nm,c=0.67872 nm,α=β=90°,γ=120°,V=0.5138692 nm3.Three strong peaks located at 32.079o,32.595o,and 50.104o with d=2.7903,2.74649,1.8194 was in accordance with,(112),and(213) planes.The optimum concentration of Tb3+ in Ca2Y8Si6O26 to yield highest photoluminescence intensity was 10 mol.% of Y3+.The corresponding excitation spectrum consisted of an intense broad band from 220 to 260 nm.The photoluminescence measurements showed that the green emission originated from 5D4-7F5 was predominant in the measured range with strong doublet lines at 543 and 549 nm.     

Complexation-Coprecipitation Synthesis and Characterization of Erbium and Antimony Doped SnO2 Conductive Nanoparticles

Er was used as a dopant for the first time in preparing conductive powder to improve its performance. Er and Sb doped SnO₂ conductive nanoparticles were prepared by the complexation-coprecipitation method with Sn, Sb₂O₃ and Er₂O₃ as the raw materials. Thermal behavior, crystal phase, and structure of the prepared conductive nanoparticles were characterized by TG/DSC, FTIR, XRD and TEM techniques, respectively. The resistivity of the prepared conductive nanoparticles was 0.29 Ω·cm; TG/DSC curves showed that the precursors lost weight completely before 750 °C; FTIR spectrum showed that the vibration peak were wide peak in 711 × 600 cm⁻¹; the Er and Sb doped SnO₂ conductive nanoparticles had intense absorption in 4000 × 1600 cm⁻¹; Er and Sb doped SnO₂ had a structure of tetragonal rutile; complex doping was achieved well by complexation-coprecipitation method and was recognized as replacement doping or caulking doping; TME showed that the particles were weakly agglomerated, the size of the particles calcined at 800 °C ranged approximately from 10 to 30 nm.     

La-doped SnO₂:synthesis and its electrochemical property

Tin dioxide(SnO2) and La-doped(1%,5%,10% in mass ratio) SnO2 samples were prepared via a hydrothermal method. The as-prepared powders were characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM) . Results showed that the particle size of SnO2 decreased gradually with the increase of the doped La element. When used as anode materials of Li ion battery,the La-doped samples exhibited better cycling performance than the pure SnO2,and the cycling performance of the La-doped samples got better and better with the increase of the doped La. The better electrochemical performance of the doped material could be attributed to the doping of La element,which not only enabled SnO2 powders to have a good dispersivity but also reduced their particle size.     

Study on analysis of crystal structure in CeO₂ doped with Er₂O₃ or Gd₂O₃

To simulate the effects of burnable poison doping in nuclear fuel UO2,Er2O3(or Gd2O3)-doped CeO2 pellets were prepared. Changes in lattice constant and atomic disordering for CeO2 due to the Er2O3 and Gd2O3 doping were measured by means of XRD and XAFS. By the Er2O3 doping,the lattice constant decreased,and a disordering of lattice structure was induced in the samples. The doping with Er2O3 also induced the disordering of atomic arrangement around Er atoms,which was observed through the change in XAFS spectra. In contrast,the effect of Gd2O3 doping was smaller than that of Er2O3 doping. The result was discussed in terms of ionic size of dopants in CeO2 crystal.     

Photoluminescence study of SiO₂ coated Eu³⁺:Y₂O₃ core-shells under high pressure

Uniform core-shell Eu3+:Y2O3/SiO2 spheres were synthesized via precipitation and the Stber method.The structural transition of core-shell Eu3+:Y2O3/SiO2 was studied by using high pressure photoluminescence spectra.With pressure increasing,the emission intensities of 5D0→7F0,1,2 transitions of Eu3+ ions decreased and the transition lines showed a red shift.The relative luminescence intensity ratio of 5D0→7F2 to 5D0→7F1 transitions decreased with increasing pressure,indicating lowering asymmetry around Eu3+ ions.During compression,structural transformation for cores in the present core-shell Eu3+:Y2O3/SiO2 sample from cubic to monoclinic took place at 7.5 GPa,and then the monoclinic structure turned into hexagonal above 15.2 GPa.After the pressure was released,the hexagonal structure transformed back to monoclinic and the monoclinic structure was kept stable to ambient pressure.     

Synthesis and photocatalytic property of Ce-doped SnO₂

Pure SnO2 and Ce-doped(1%,4%,7%,10% in mass ratio) SnO2 powders were prepared by a simple sol-gel method.The as-prepared samples were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),and Brunauer-Emmett-Teller(BET) specific surface area analyzers.Results showed that the 7% Ce-doped sample has a particle size of 0.1-0.3 μm with a narrow particle size distribution while the pure SnO2 was consisted of large agglomerated particles with a diameter up to several micrometers.When used as the catalyst to degrade methyl orange(MO),the 7% Ce-doped sample showed best photocatalytic property.These properties can be attributed to the large surface area and small particle size of the 7% Ce-doped sample.     

Electrospinning synthesis and luminescent properties of Lu₂O₃:Eu³⁺ nanofibers

One-dimensional Lu2O3:Eu3+ nanofibers were prepared by electrospinning followed by high-temperature calcinations.Thermogravimetric and differential thermal analysis,X-ray powder diffraction,Fourier transform infrared spectroscopy,scanning electron microscopy,photoluminescent spectra and decay curves were used to characterize the samples.Results showed that samples began to crystallize at ～500 oC and crystallized completely around 1000 oC.The average diameter of nanofibers(1000 oC annealed) was about 55 nm and the particle size of Lu2O3:Eu3+ increased with increasing annealing temperature.Under ultraviolet excitation,nanofibers exhibited typical red emission of Eu3+ in Lu2O3.The effect of heat-treatment temperature on luminescent properties of nanofibers was also discussed.     

Nd-doped SnO₂:characterization and its gas sensing property

Nd-doped(2%,5%,10% in mass ratio) SnO2 powders were prepared via a facile hydrothermal procedure.The as-prepared samples were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),and Brunauer-Emmett-Teller(BET) specific surface area analyzers.Results showed that the Nd-doped SnO2 samples had more uniform and smaller primary particles compared with the pure sample,the particle size of the doped SnO2 decreased gradually with the increase of Nd,and the specific surface area also increased with the increase of the doped Nd.When used as gas sensing materials,the 5% and 10% Nd-doped sample showed high sensitivity and selectivity to ethanol.Furthermore,the Nd-doped sample showed fast response and recovery time to ethanol gas.This could be attributed to their small diameter,large surface area and Nd element doping.     

Ultraviolet-shielding and conductive double functional films coated on glass substrates by sol-gel process

Ultraviolet-shielding and conductive double functional films were composed of CeO2-TiO2 film and SnO2:Sb film deposited on glass substrates using sol-gel process.Ce(NO3)3·6H2O and Ti(C4H9O4),SnCl4 and SbCl3 were used as precursors of the two different functional films respectively.The CeO2-TiO2 films were deposited on glass substrates by sol-gel dip coating method,and then the SnO2:Sb films with different thickness were deposited on the pre-coated CeO2-TiO2 thin film glass substrates,finally,the substrates coated with double functional films were annealed at different temperatures.The optical and electrical properties of the CeO2-TiO2 films and the double films were measured by UV-Vis spectrometer and four probe resistance measuring instrument.The crystal structures and surface morphology of the films were characterized using XRD and optical microscope,respectively.The obtained results show that the ultraviolet-shielding rate of the glass substrates with CeO2-TiO2 films is not less than 90%,and transmittance in visible lights can reach 65%.With the thickness of the SnO2:Sb film increasing,its conductivity became better,and the surface resistance is about 260 Ω/ when the SnO2:Sb films were deposited 11 cycles of the dip on the pre-coated CeO2-TiO2 glass.The ultraviolet-shielding rate of the glass substrates with double functional films is higher than 97%,and the peak transmittance in the visible lights is 72%.Additionally,with increasing the heat treatment time,the Na+ of the glass substrates diffuses into the films,resulting in the particle size of SnO2 crystal smaller.     

Preparation and Characterization of Sol-Gel Derived Au Nanoparticle Dispersed Y2O3：Eu Films

Gold nanoparticles dispersed Y2O3 films were prepared through a sol-gel method by using yttrium acetate and Au nanoparticles colloid as precursors. The films were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM） and UV-VIS absorption spectra. XRD patterns and TEM images of Y2O3 ＋ Au films give the same resuits on structure and particle size as that of pure Y2O3 films. The surface plasma resonance （SPR） of Au nanoparticles in Y2O3 ＋ Au film was observed around 550 nm in the absorption spectrum and its position shifts to red with increasing annealing temperature is caused by the increase of dielectric constant of Y2O3 matrix and the size of Au nanoparticles. The second and third order nonlinear optical effects of Y2O3 ＋ Au films were also observed. The photoluminescent properties of Y2O3 ： Eu ＋ Au films were investigated and results indicate that there exist an energy transfer from Eu^3 ＋ to Au nanoparticles and this energy transfer decreases the emission of Eu^3 ＋ in Y2O3 ： Eu ＋ Au film.     

Low-temperature electrochemical synthesis and characterization of ultrafine Y（OH）_3 and Y_2O_3 nanoparticles

Ultrafine Y(OH)3 nanoparticles were successfully deposited from an additive-free 0.005 mol/L YCl3 low-temperature bath on the steel cathode at the current density of 0.5 mA/cm2 and bath temperature of 10 oC. Heat treatment of the prepared Y(OH)3 nanoparticles at 600 oC in air led to the formation of Y2O3 nanoparticles. Thermal behavior and phase transformation during the heat treatment of Y(OH)3 were investigated by differential scanning calorimetry (DSC) and thermogramimetric analysis (TGA). The morphologies, crystal structures and compositions of the prepared materials were examined by means of scanning and transmission electron microscopy (SEM and TEM) as well as X-ray diffraction (XRD) and FT-IR spectroscopy. The results showed that the prepared Y(OH)3 nanoparticles was essentially amorphous and composed of well dispersed ultrafine particles with size of 4 nm. After heat treatment, the obtained oxide product was well crystallized cubic phase of Y2O3 nanoparticles with the grain size of around 5 nm. It was concluded that low-temperature cathodic electrodeposition offered a facile and feasible way for preparation of ultrafine Y(OH)3 and Y2O3 nanoparticles.     

Mechanical properties of UHMWPE/Sm₂O₃ composite shielding material

UHMWPE have good effect to slow down fast neutrons and Sm2O3 can absorb the thermal neutrons.A new style UHMWPE/ Sm2O3 composite shielding material was manufractured by hot-press moulding method.The microstructure and mechanical properties were characterized by IR and SEM.The results indicate that Sm2O3 distributed continuously,evenly in UHMWPE,and the interface was combined closely.Hardness of UHMWPE/Sm2O3 composites increased at first and decreased and tensile strength decreased with the increasing of Sm2O3 mass fraction.     

Preparation and performance of electrodeposited Ni-TiB₂-Sm₂O₃ composite coatings

Sm2O3 and TiB2 were used as codeposited particles in electrodeposition Ni-TiB2-Sm2O3 composite coatings to improve its performance. Ni-TiB2-Sm2O3 composite coatings were electrodeposited in the nickel sulfate,hexadecylpyridinium bromide and cetyltrimethylammonium bromide solution containing TiB2 and Sm2O3 particles. The content of codeposited Sm2O3 in the composite coating was controlled by changing the concentrations of Sm2O3 particles in the solution. The composite coatings were characterized with X-ray diffraction(XRD) and inductively coupled plasma-atomic emission spectrometer(ICP-AES) . The effects of Sm2O3 content on microhardness,wear weight loss and friction coefficient of composite coatings were investigated,respectively. The microhardness of the Ni-TiB2-Sm2O3 composite coatings was 19.35%,16.58%,2.03% higher than that of the Ni coating,Ni-Sm2O3 and Ni-TiB2 composite coatings,respectively. The wear weight loss of the Ni-TiB2-Sm2O3 composite coatings was 7,2.33,1.22 times lower than that of the Ni coating,Ni-Sm2O3 and Ni-TiB2 composite coatings,respectively. The friction coefficient of the Ni coating,Ni-Sm2O3,Ni-TiB2 and Ni-TiB2-Sm2O3 composite coatings were 0.712,0.649,0.850 and 0.788,respectively. The loading-bearing capacity and the wear-reducing effect of the Sm2O3 particles were closely related to the content of Sm2O3 particles in the composite coatings.     

Preparation of Y2O3 Nanoparticles Organosol by Microemulsion Method

Y2O3 nanoparticles organosol coated with DBS was prepared by microemulsion method. The optimum preparative conditions of Y2O3 nanoparticles organosol were obtained. TEM analysis indicates that the prepared Y2O3 nanoparticles are spherical in shape. The size is about 5 nm. The size distribution is in the narrow range and no agglomerates are observed. Y2O3 nanoparticles coated with DBS are easy to dissolve in weak polar solvents.     

Hydrothermal synthesis,structure study and luminescent properties of YbPO₄:Tb³⁺ nanoparticles

YbPO4:Tb3+ were synthesized by mild hydrothermal method.The luminescent properties,morphologies and structure of the obtained powders were characterized by photoluminescence(PL) spectra,FESEM,X-ray diffractometer(XRD) and FTIR.The results showed that the prepared YbPO4:Tb3+ nanoparticles were pure tetragonal phase and the average grain size varied with increasing of Tb3+ concentration.Hydrothermal temperature was revealed to be the key factor to enhance the emission intensity of YbPO4:Tb3+ phosphors.The spherical nanoparticles could be effectively excited by near UV(369 nm) light and exhibited green performance at 543 nm(5D4→7F5),489 nm(5D4→7F6) and 586 nm(5D4→7F4).The CIE chromaticity was calculated to be x=0.298,y=0.560.The YbPO4:Tb3+ nanoparticles exhibited potential to act as UV absorber for solar cells to enhance the conversion efficiency.     

A white long-lasting phosphor Y2O2S:Tb3+, Sm3+: an improvement of Y2O2S:Tb3+

As an improvement of reported Y202S:Tb3 , a white-light long-lasting phosphor: Y2O2S:Tb3 , Sm3 was prepared by the solid-state reaction. The photo-luminescence spectra showed that the position and shape of Th3 and Sm3 emissions under UV excitation were similar in this host, which ensured a stable white emission color (daylight standard of IEC) under different excitations. The decay curves of co-doped samples indicated that the decay times of emissions of the two ions were close. The thermo-luminescence measurement suggested that the traps created by the doped Sm3 ions were helpful to postpone the white afterglow of co-doped samples. Therefore, thefunction of co-doped Sm3 ions was confirmned as improving the white emission colors of samples and acting as new trap centers.     

Synthesis and characterization of CaAl_xO_y:Eu²⁺ phosphors prepared using solution-combustion method

Europium-doped calcium aluminate(CaAlxOy:Eu2+) phosphors were obtained at low temperatures(500 oC) by the solution-combustion of corresponding metal nitrate-urea solution mixtures.The particle size and morphology and the structural and luminescent properties of the as-synthesized phosphors were examined by means of scanning electron microscopy(SEM),X-ray diffraction(XRD),Auger spectroscopy,transmission electron spectroscopy(TEM) and photoluminescence(PL).It was found that the Ca:Al molar ratios showed greatly influence not only on the particle size and morphology,but also on their PL spectra and structure.With the Ca:Al molar ratios increasing from 6:100 to 26:100,the structure of as-synthesized phosphor changed from CaAl12O19 to monoclinic CaAl2O4 and the dominant emitting light from red to blue,implying that the oxidation state of doped europium ions changed from trivalent to divalent due to the structure variation of host lattice.A blue phosphor with almost pure phase can be easily prepared by solution combustion method with suitable Ca:Al molar ratio.     

Synthesis of La3+ and Nd3+ co-doped yttria nanopowder for transparent ceramics by oxalate precipitation method

Polycrystalline Nd3+ and La3+ co-doped yttria nanopowder Nd3+:Y1.90La0.10O3 for transparent ceramics was synthesized by co-precipitation method using oxalate acid as the precipitant and(NH4)2SO4 as the electrical stabilizer under ultrasonic radiation.Nanopowders calcined at different temperatures were characterized with thermal gravimetric-differential thermal analysis(TG/DTA),X-ray diffraction(XRD),transmitting electron microscopy(TEM),energy dispersive spectrometry(EDS) and spectral analysis techniques.Th...     

Preparation and Properties of Orthogonal Piezoelectric Composite Materials

. PZT piezoelectric ceramic with La2O3, SrCO3, BaO and Sb2O5 was prepared. It has high value of the piezoelectric strain constant d33 ( -681 PC/N) and high value of-d33/d31 (2.65). Orthogonal piezoelectric composite materials was designed and prepared by PZT, DAD- 40 electric conductive adhesive and E51 epoxy resin. The OPCM shows obvious orthogonal anisotropy. The matching property of the interface between piezoelectric ceramic and polymer of OPCM relies on the defects of interface. The proper conductive mid-layer could improve the matching property of the interface.