Sliding friction and wear performance of Ti6Al4V in the presence of surface-capped copper nanoclusters lubricant

The friction and wear properties of Ti₆Al₄V sliding against AISI52100 steel ball under different lubricative media of surface-capped copper nanoclusters lubricant—Cu nanoparticles capped with O,O′-di-n-octyldithiophosphate (Cu-DTP), rapeseed oil and rapeseed oil containing 1 wt% Cu-DTP was evaluated using an Optimol SRV oscillating friction and wear tester. The wear mechanism was examined using scanning electron microscopy (SEM) and X-ray photoelectron spectrosmeter (XPS). Results indicate that Cu-DTP can act as the best lubricant for Ti₆Al₄V as compared with rapeseed oil and rapeseed oil containing 1 wt% Cu-DTP. The applied load and sliding frequency obviously affected the friction and wear behavior of Ti₆Al₄V under Cu-DTP lubricating. The frictional experiment of the Ti₆Al₄V sliding against AISI52100 cannot continue under the lubricating condition of rapeseed oil or rapeseed oil containing 1 wt% Cu-DTP when the applied load are over 100 N. Surprisingly, the frictional experiment of Ti₆Al₄V sliding against AISI52100 steel can continue at the applied load of 450 N under Cu-DTP lubricating. The tribochemical reaction film containing S and P is responsible for the good wear resistance and friction reduction of Ti₆Al₄V under Cu-DTP at the low applied load. However, a conjunct effect of Cu nanoparticle deposited film and tribochemical reaction film containing S and P contributes to the good tribological properties of Ti₆Al₄V under Cu-DTP at the high-applied load.     

Effect of ZrO2 Nanoparticles Additive on the Tribological Behavior of Multialkylated Cyclopentanes

Monodisperse ZrO₂ nanoparticles with a particle size of about 6–7 nm and low volatile multialkylated cyclopentanes (MACs) lubricant were prepared and characterized. The effect of ZrO₂ nanoparticles as additive on the friction and wear behavior of MACs base oil was investigated. The friction and wear performance of 2 wt% ZrO₂ nanoparticles + MACs was evaluated using an Optimal SRV oscillating friction and wear tester, with a steel ball sliding against the same steel counterpart disc. Results indicate that the wear resistance and load-carrying capacity of MACs base oil were markedly raised and its friction coefficient changed little when 2 wt% ZrO₂ nanoparticles were added to it.     

Comparison of wear properties of tool steels AISI D2 and O1 with the same hardness

Two commercial cold work tool steels, AISI D2 and O1, were heat treated in order to obtain the same hardness 700 HV (60 HRc) and were subsequently tested in three different modes of wear, namely in adhesion, three-body and two-body abrasion, by using pin-on-disk, dry sand/rubber wheel apparatus and pin abrasion on SiC, respectively. Even though AISI O1 and D2 steel are heat treated to the same hardness, they perform differently under the three modes of wear examined. The results show that the steel microstructures play the most important role in determining the wear properties. For relatively low sliding speeds AISI O1 steel performs up to 12 times better than AISI D2 steel in adhesive wear. For higher sliding speeds, however, this order is reversed due to oxidation taking place on the surface of the AISI D2 steel. The wear rate of both tool steels in three-body and two-body abrasion wear is proportional to the applied load. In three-body abrasive wear, AISI D2 exhibits a normalised wear rate about two times lower than the AISI O1 tool steel, and this is due to the presence of the plate-like hard carbides in its microstructure. Both tool steels perform 3–8 times better in three-body abrasive wear conditions than in two-body abrasive wear.     

Steel machining chips as reinforcements to improve sliding wear resistance of metal alloys: Study of a model Zn-based alloy system

Two new steel-reinforced, metal-matrix composites (MMCs), Kirksite+1080 and Kirksite+M2 are developed by adding 25 wt% of AISI 1080/AISI M2 steel machining chips to a zinc-based alloy, Kirksite (4% Al and 3% Cu). The sliding wear resistance of the Zn alloy and the two MMCs, against AISI 52100 steel, is determined under increasing normal load (1–10 N) and temperature (25–150 °C), using a pin-on-disc configuration. The MMCs are found to exhibit superior wear performance under all test conditions. At room temperature, a maximum wear reduction in excess of 70% is obtained for the composites relative to the Zn-alloy at the highest load of 10 N. This reduction is as much as 86% at 150 °C and 1 N for the Kirksite+M2. The wear-reducing ability of the steel reinforcements is generally greater at the more severe contact conditions. The stability of the MMC matrices and recommended limits to the MMC operating temperatures are established using deformation measurements made via dynamic mechanical analysis. The principal wear mechanisms are analysed based on the sliding wear measurements, complemented by optical microscopy and SEM observations, and EDX microanalysis. The results show that the steel chip reinforcements are effective in improving the wear resistance of Zn alloys under severe conditions. Implications for use of low-cost machining chips as reinforcements to create MMCs for improved wear performance, and for recycling/reuse of these chips in advanced structural material systems are discussed.     

Sliding contacts for the pharmaceutical industry: failure analysis and dry sliding tests for the replacement of hard Cr on AISI 316L steel

Several alternatives were compared for the replacement of hard electroplated Cr coating to improve the tribological properties of the AISI 316L austenitic stainless steel for pharmaceutical packaging applications, including low temperature carburizing (LTC), thermal spray coatings (Al₂O₃-13TiO₂, WC-17Co), substitution of the AISI 301 reference counterface with polymeric materials (PTFE, UHMWPE, PEEK). In dry sliding block on ring tests, the LTC AISI 316L cylinders lead to the lowest wear rates of the AISI301 sliders under low loads (up to 10 N). When considering the polymer vs. uncoated AISI 316L couple, PEEK and UHMWPE lead to lower friction and comparable wear rates with respect to the reference couple (AISI 301 vs. Hard Cr coated-AISI 316L) in the whole range of tested loads.     

Tribological properties of γ-Y2Si2O7 ceramic against AISI 52100 steel and Si3N4 ceramic counterparts

Reciprocating ball-on-flat dry sliding friction and wear experiments have been conducted on single-phase γ-Y₂Si₂O₇ ceramic flats in contact with AISI 52100 bearing steel and Si₃N₄ ceramic balls at 5–15 N normal loads in an ambient environment. The kinetic friction coefficients of γ-Y₂Si₂O₇ varied in the range over 0.53–0.63 against AISI 52100 steel and between 0.51–0.56 against Si₃N₄ ceramic. We found that wear occurred predominantly during the running-in period and it almost ceased at the steady friction stage. The wear rates of γ-Y₂Si₂O₇ were in the order of 10^?4 mm³/(N m). Besides, wear debris strongly influenced the friction and wear processes. The strong chemical affinity between γ-Y₂Si₂O₇ and AISI 52100 balls led to a thick transfer layer formed on both contact surfaces of the flat and counterpart ball, which changed the direct sliding between the ball and the flat into a shearing within the transfer layer. For the γ-Y₂Si₂O₇/Si₃N₄ pair, a thin silica hydrate lubricant tribofilm presented above the compressed debris entrapped in the worn track and contact ball surface. This transfer layer and the tribofilm separated the sliding couple from direct contact and contributed to the low friction coefficient and wear rate.     

Influence of Steel Type on the Propensity for Tribochemical Wear in Boundary Lubrication with a Wind Turbine Gear Oil

Tribochemical wear may occur at the interface between a surface and a lubricant as a result of chemical and mechanical interactions in a tribological contact. Understanding the onset of tribochemical wear damage on component surfaces requires the use of high resolution techniques such as transmission electron microscopy (TEM). In this study, two steel types, case carburized AISI 3310 and through-hardened AISI 52100, were wear tested using a ball-on-disk rolling/sliding contact tribometer in fully formulated commercial wind turbine gearbox oil under boundary lubrication conditions with 10% slip. With the exception of steel type, all other test conditions were held constant. Conventional tribofilm analysis in the wear tracks was performed using X-ray photoelectron spectroscopy, and no significant composition differences were detected in the tribofilms for the different steel disk types. However, TEM analysis revealed significant tribochemical wear differences between the two steel types at multiple length scales, from the near-surface material microstructure (depth < 500 nm) to the tribofilm nanostructure. Nanometer-scale interfacial cracking and surface particle detachment was observed for the AISI 52100 case, whereas the tribofilm/substrate interface was abrupt and undamaged for the AISI 3310 case. Differences in tribofilm structure, including the location and orientation of MoS₂ single sheet inclusions, were observed as a function of steel type as well. It is suggested that the tribochemical wear modes observed in these experiments may be origins of macroscopic surface-initiated damage such as micropitting in bearings and gears.     

A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

The friction and wear properties of the polyetheretherketone (PEEK) based composites filled with 5 mass% nanometer or micron Al₂O₃ with or without 10 mass% polytetrafluroethylene (PTFE) against the medium carbon steel (AISI 1045 steel) ring under the dry sliding condition at Amsler wear tester were examined. A constant sliding velocity of 0.42 m s⁻¹ and a load of 196 N were used in all experiments. The average diameter 250 μm PEEK powders, the 15 or 90 nm Al₂O₃ nano-particles or 500 nm Al₂O₃ particles and/or the PTFE fine powders of diameter 50 μm were mechanically mixed in alcohol, and then the block composite specimens were prepared by the heat compression moulding. The homogeneously dispersion of the Al₂O₃ nano-particles in PEEK matrix of the prepared composites was analyzed by the atomic force microscopy (AFM). The wear testing results showed that nanometer and micron Al₂O₃ reduced the wear coefficient of PEEK composites without PTFE effectively, but not reduced the friction coefficient. The filling of 10 mass% PTFE into pure PEEK resulted in a decrease of the friction coefficient and the wear coefficient of the filled composite simultaneously. However, when 10 mass% PTFE was filled into Al₂O₃/ PEEK composites, the friction coefficient was decreased and the wear coefficient increased. The worn scars on the tested composite specimen surfaces and steel ring surfaces were observed by scanning electron microscopy (SEM). A thin, uniform, and tenacious transferred film on the surface of the steel rings against the PEEK composites filled with 5 mass% 15 nm Al₂O₃ particles but without PTFE was formed. The components of the transferred films were detected by energy dispersive spectrometry (EDS). The results indicated that the nanometer Al₂O₃ as the filler, together with PEEK matrix, transferred to the counterpart ring surface during the sliding friction and wear. Therefore, the ability of Al₂O₃ to improve the wear resistant behaviors is closely related to the ability to improve the characteristics of the transfer film.     

Tribological behaviour and wear mechanism of MoS2–Cr coatings sliding against various counterbody

MoS₂–Cr coatings with different Cr contents have been deposited on high speed steel substrates by closed field unbalanced magnetron (CFUBM) sputtering. The tribological properties of the coatings have been tested against different counterbodies under dry conditions using an oscillating friction and wear tester. The coating microstructures, mechanical properties and wear resistance vary according to the Cr metal-content. MoS₂ tribological properties are improved with a Cr metal dopant in the MoS₂ matrix. The optimum Cr content varies with different counterbodies. Showing especially good tribological properties were MoS₂–Cr8% coating sliding against either AISI 1045 steel or AA 6061 aluminum alloy, and MoS₂–Cr5% coating sliding against bronze. Enhanced tribological behavior included low wear depth on coating, low wear width on counterbody, low friction coefficients and long durability.     

Tribocorrosion behavior of Ni-17.5Si-29.3Cr alloy in sulfuric acid solution

The tribocorrosion property of a Ni-17.5Si-29.3Cr alloy against a Si₃N₄ ball was studied in comparison with AISI321 stainless steel using a ball-on-disk reciprocating tribotester in 1 M sulfuric acid (H₂SO₄) solution. The effects of load and sliding speed on the tribocorrosion properties of the alloy were investigated. The results indicated that the wear rate of the alloy increased while the friction coefficient decreased with increasing load. The wear rate of the alloy increased linearly with increasing sliding speed and the friction coefficient increased in the initial stages and then remained constant with increasing sliding speed. The wear mechanisms were mainly microploughing, uniform corrosion and pitting corrosion. Under the experimental conditions of the present study, the Ni-17.5Si-29.3Cr alloy showed excellent corrosion-resistence and anti-wear ability compared with AISI321 stainless steel.     

Friction and wear behaviour of plasma-sprayed Cr2O3 coatings against steel in a wide range of sliding velocities and normal loads

This study investigates the influence of sliding speed and normal load on the friction and wear of plasma-sprayed Cr₂O₃ coatings, in dry and lubricated sliding against AISI D2 steel. Friction and wear tests were performed in a wide speed range of 0.125–8 m/s under different normal loads using a block-on-ring tribometer. SEM, EDS and XPS were employed to identify the mechanical and chemical changes on the worn surfaces. A tangential impact wear model was proposed to explain the steep rising of wear from the minimum wear to the maximum wear. The results show that the wear of Cr₂O₃ coatings increases with increasing load. Secondly, there exist a minimum-wear sliding speed (0.5 m/s) and a maximum-wear sliding speed (3 m/s) for a Cr₂O₃ coating in dry sliding. With the increase of speed, the wear of a Cr₂O₃ coating decreases in the range 0.125–0.5 m/s, then rises steeply from 0.5 m/s to 3 m/s, followed by a decrease thereafter. The large variation of wear with respect to speed can be explained by stick-slip at low speeds, the tangential impact effect at median speeds and the softening effect of flash temperature at high speeds. Thirdly, the chemical compositions of the transfer film are a-Fe₂O₃ in the speed range 0.25–2 m/s, and FeO at 7 m/s. In addition, the wear mechanisms of a Cr₂O₃ coating in dry sliding versus AISI D2 steel are adhesion at low speeds, brittle fracture at median speeds and a mixture of abrasion and brittle fracture at high speeds. Finally the lubricated wear of Cr₂O₃ coating increases sharply from 1 to 2.8 m/s.     

Direct laser cladding of SiC dispersed AISI 316L stainless steel

The present study concerns development of SiC dispersed (5 and 20 wt%) AISI 316L stainless steel metal-matrix composites by direct laser cladding with a high power diode laser and evaluation of its mechanical properties (microhardness and wear resistance). A defect free and homogeneous composite layer is formed under optimum processing condition. The microstructure consists of partially dissociated SiC, Cr₃C₂ and Fe₂Si in grain refined stainless steel matrix. The microhardness of the clad layer increases to a maximum of 340 VHN (for 5% SiC dispersed) and 800 VHN (for 20% SiC dispersed) as compared to 150 VHN of commercially available AISI 316L stainless steel. Direct laser clad SiC dispersed AISI 316L stainless steel has shown an improved wear resistance against diamond surface with a maximum improvement in 20% SiC dispersed AISI 316L stainless steel. The mechanism of wear was predominantly abrasive in nature.     

Study of tribological performance of ECR-CVD diamond-like carbon coatings on steel substrates: Part 1. The effect of processing parameters and operating conditions

Diamond-like carbon (DLC) coatings were prepared on AISI 440C steel substrates at room temperature by electron cyclotron resonance chemical vapor deposition (ECR-CVD) process in C₂H₂/Ar plasma. Using the designed Ti/TiN/TiCN/TiC interfacial transition layers, relatively thick DLC coatings (1-2 μm) were successfully prepared on the steel substrates. The friction and wear performance of the DLC coatings was evaluated by ball-on-disk tribometry using a steel counterbody at various normal loads (1-10 N) and sliding speeds (2-15 cm/s). By optimizing the deposition parameters such as negative bias voltage, DLC coatings with hardness up to 30 GPa and friction coefficients lower than 0.15 against the 100Cr6 steel ball could be obtained. The friction coefficient was maintained for 100,000 cycles (∼2.2 km) of dry sliding in ambient environments. In addition, the specific wear rates of the coatings were found to be extremely low (∼10⁻⁸ mm³/Nm); at the same time, the ball wear rates were one order of magnitude lower. The influences of the processing parameters and the sliding conditions were determined, and the frictional behavior of the coatings was discussed. It has been found that higher normal loads or sliding speeds reduced the wear rates of the coatings. Therefore, it is feasible to prepare hard and highly adherent DLC coatings with low friction coefficient and low wear rate on engineering steel substrates by the ECR-CVD process. The excellent tribological performance of DLC coatings enables their industrial applications as wear-resistant solid lubricants on sliding parts.     

Sliding wear resistance of reactive plasma sprayed Ti–TiN coatings

The reactive plasma spraying (RPS) of titanium powders in a nitrogen containing plasma gas produces thick coatings characterised by microdispersed titanium nitride phases in a titanium matrix. In this paper, the wear resistance properties of Ti–TiN coatings deposited on carbon steel substrates by means of RPS technique are studied. Wear tests were performed in block-on-ring configuration and dry sliding conditions, at different applied loads (45 and 100 N) and sliding velocities (in the range 0.4–2.0 m s⁻¹) by using hardened and stress relieved AISI O2 disks as counterpart. At low applied load the wear volumes are low, and tend to slightly increase as the sliding velocity increases. At high applied load and low sliding velocities the highest wear volumes for the coated samples are observed, due to adhesion in the contact area with the tool steel counterpart and decohesion of coating particles. As the sliding velocity is increased, the wear volume of the coated samples tends to decrease owing to oxidation phenomena.     

Comparison of the tribological behavior of columnar-grained polycrystalline copper with vertical/horizontal orientation sliding against AISI 1045 steel

The unlubricated tribological behavior of columnar-grained polycrystalline copper with vertical orientation (VO) and horizontal orientation (HO) in sliding against AISI 1045 steel is investigated in room air. The friction coefficient and wear rate of HO Cu in sliding against AISI 1045 steel are lower than that of the VO Cu. The friction-induced layers are distinct. The friction-induced layer on HO Cu is composed of metallic Cu, Fe₂O₃, and Fe₃O₄. The wear debris is agglomerated fine particles. The friction-induced layer on VO Cu presents characteristics of plastic deformation and flow. The wear debris is plate-like. The grain orientations and boundaries of VO/HO Cu sample are contributed to the different friction-induced layer and wear mechanism. For VO Cu, the grain boundary perpendicular to the sliding direction makes the slip motion activate difficultly. For HO Cu, the grain boundary parallel to the sliding direction makes the slip motion activate easily.     

Relations of counterface materials with stability of tribo-oxide layer and wear behavior of Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy

Dry sliding wear tests of Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy (TC11 alloy) sliding against AISI 52100 and AISI M2 steels were performed under the load of 50–250 N at 25–600 °C. For two kinds of counterface materials, the titanium alloy presented totally different wear behaviours as the function of temperature. The appreciable variations of the titanium alloy sliding against different counterface materials were attributed the fact that a hard counterface caused unstable existence of tribo-layers by its microcutting action, thus resulting in the increase of wear rate. It is suggested that the hard counterface must be avoided as the counterface for the titanium alloy/steel sliding system.     

Laser composite surfacing of AISI 304 stainless steel with titanium boride for improved wear resistance

The present study concerns development of a hard in situ boride-dispersed composite layer on the surface of AISI 304 stainless steel substrate to improve the wear resistance property. Laser processing was carried out by melting the surface of sand-blasted AISI 304 stainless steel substrate using a continuous wave CO₂ laser and simultaneous deposition of a mixture of K₂TiF₆ (potassium titanium hexafluoride) and KBF₆ (potassium hexafloroborate) (in the weight ratio of 2:1) using Ar as shrouding environment. Powder feed rate was maintained constant at 4 g/min. Irradiation results in dissociation of a pre-deposited mixture along with a part of the stainless steel substrate, intermixing and rapid solidification to form the composite layer on the surface. The micro-structure of composite layer consists of dispersion of titanium boride particles in AISI 304 stainless steel matrix. Volume fraction of particles is found to be uniform throughout the composite layer, though varied with laser parameters. The micro-hardness of the surface was improved 250–350 VHN as compared to 220 VHN of the AISI 304 stainless steel substrate with a significant improvement in wear resistance property. The mechanism of wear was found to be a combination of adhesive and abrasive in as-received stainless steel. However, it was predominantly abrasive for laser composite surfaced stainless steel.     

The Tribological Behaviour of Fe–28Al–5Cr/TiC Under Liquid Paraffine Lubrication

The tribological behaviour of Fe–28Al–5Cr and its composites containing 15, 25 and 50 wt% TiC (corresponding to 19.3, 31.2 and 57.6 vol%), produced by hot-pressing process, was investigated under liquid paraffine lubrication against an AISI 52100 steel ball in ambient environment at varied applied loads and sliding speeds. It was found that the wear resistance increased and friction coefficient decreased with increasing of TiC content. The coefficients of friction are in the range of 0.09–0.14 at the given testing conditions. The wear rates of all the materials except the 50% composite are on the order of 10⁻⁶–10⁻⁵ mm³ m⁻¹, the wear rate for the 50% composite is too low to quantify under the two sliding conditions, (50 N, 0.04 m/s) and (100 N, 0.02 m/s). The wear rates of all the materials increase as applied load increases and the increasing extent diminishes with the increase of TiC content, but first increase slightly and then nearly remains steadiness with increasing sliding speed. The 50 wt% composite has wear resistance about 7–20 times better than pure Fe–28Al–5Cr at different sliding parameters. The enhanced wear resistance by TiC addition is attributed to the high hardness of the composites, as well as support of the oil lubrication film/layer by the hard TiC phase. The worn surfaces of all the materials are analyzed by a scanning electron microscope. The dominant wear mechanism of the Fe–28Al–5Cr and 15% composite is grooving and flaking-off, but those of the 25 and 50% composites are mainly shallow grooving.     

Tribological characterization of tungsten nitride coatings deposited by reactive magnetron sputtering

The structure, hardness, friction and wear of tungsten nitrides prepared by d.c. reactive magnetron sputtering were investigated. The coatings were deposited with different nitrogen to argon ratios; the total pressure was kept constant. The tribological tests were performed on a pin-on-disc tribometer in terrestrial atmosphere with 100Cr6 steel, Al₂O₃ and Si₃N₄ balls as sliding counter-bodies. The wear tracks, the ball-wear scars and the wear debris were analysed by scanning electron microscopy in order to characterize the dominant wear mechanisms.The coatings exhibited different phases as a function of the nitrogen content: films with low N content exhibited the α-W phase; β-W phase was dominant for nitrogen contents from 12 to 15 at.% and β-W₂N was observed for nitrogen content higher that 30 at.%. The mechanical and tribological properties of the tungsten nitride coatings were strongly influenced by the structure. The hardness and the Young's modulus values were in the ranges (29–39 GPa) and (300–390 GPa), respectively; the lowest values correspond to the coatings with the highest nitrogen content. Generally, the friction and wear rate of tungsten nitride coatings sliding against ceramic balls increased with nitrogen content reaching a maximum at 12 at.%; further increase of the nitrogen content led to a decrease of the friction and wear. The sliding with the steel balls did not wear the coatings under the selected testing conditions.     

The tribological properties of bronze–SiC–graphite composites under sea water condition

Bronze–SiC–nickel coated graphite composites were fabricated by powder metallurgy technique (P/M). The tribological properties of composites sliding against AISI321 stainless steel pin were studied under sea water condition. The graphite is an effective solid lubricant in sea water environment. The SiC improved the hardness and tribological properties of composites. The friction coefficient of bronze–SiC–graphite composites increased with the increase of SiC. However, the specific wear rate of bronze–SiC–graphite composites decreased with increasing SiC. Bronze-2 wt% SiC-11.7 wt% nickel coated graphite composite showed the best tribological properties due to the synergistic effects of reinforcements.