Protective effect of bioactive ceramics on liver injury: regulation of pro-inflammatory cytokins expression

Aim of study A bioactive ceramics has been reported to regulate the expression of inflammatory cytokines in macrophage cells activated by lipopolysaccharides (LPS). In present study, we investigated the anti-inflammatory effect of bioactive ceramics using liver injury model in mouse. Materials and Methods Mice were divided into three groups: Normal group, LPS group (LPS and no ceramics treatment), Ceramics group (LPS and ceramics treatment). Results LPS administration induced the increase of plasma aspartate aminotransferase (AST) and alanine aminotransferase (ALT) in mouse. The losses of cytoplasm of hepatocytes due to LPS caused the increase of AST and ALT in mouse plasma. In Ceramics group, however, the concentration of AST and ALT were much lower than LPS group until 6 weeks. And the losses of cytoplasm were rarely seen in Ceramics group. RT-PCR results showed that the decrease of proinflammatory cytokines such as IL-1β and IL-6 was observed in Ceramics group. Moreover, TGF-β1 and VEGF expression was increased in Ceramics group. Conclusion Bioactive ceramics effectively protected endotoxin-induced liver injury by attenuation of inflammatory processes in mice.     

Correlative analyses of nitric oxide generation rates and nitric oxide synthase levels in individual cells using a modular cell-retaining device

Nitric oxide (NO) is recognized as one of the major immune system agents involved in the pathogenesis and control of various diseases that may benefit from novel drug development, by exploiting NO signaling pathways and targets. This calls for detection of both intracellular levels of NO and expression of its synthesizing enzymes (NOS) in individual, intact, living cells. Such measurements are challenging, however, due to short half-life, low and fluctuating concentrations of NO, cellular heterogeneity, and inability to trace the same cells over time. The current study presents a device and methodology for correlative analysis of NO generation rates and NOS levels in the same individual cells, utilizing fluorescent imaging followed by immunohistochemistry (IHC). U937 promonocyte cell populations demonstrated significant heterogeneity in their baseline levels, in NO-generation kinetics, and in their response rates to stimuli. Individual cell analysis exposed cell subgroups which showed enhanced NO production upon stimulation, concomitantly with significant up-regulation of inducible NOS (iNOS) levels. Exogenous NO modulated the expression of iNOS in nondifferentiated cells within 1 h, in a dose-dependent manner, while treatment with lysophosphatidylcholine (LPC) enhanced the expression of iNOS, demonstrating a nondependence on NO production.     

Computation of non covalent interactions in iNOS proteins: A gene expressed by phagocytosis by macrophage cells in prosthetic particulate debris

Nitric oxide is known to be one of the principal mediators of action of many cytokines. The possibility of inducible nitric oxide (iNOS) synthase expression from macrophage is widely studied. This work comprises of numerical computation of the non-covalent interactions in 15 iNOS proteins from the Protein Data Bank (PDB) through the cation–π interactions in them. It was observed that among all the 15 iNOS proteins studied Arg has a higher composition than Lys but the cation–π interaction was almost similar in all the 15 iNOS proteins studied. Also, all the 15 iNOS protein had a higher electrostatic energy than the van der Waals energy. Moreover, there was no Lys–Tyr pair involved in the cation–π interaction in any of the iNOS protein studied. On the other hand the Arg–Trp pair had the strongest contribution towards cation–π interactions as compared to other pairs. The long range interactions among residues were predominant in all the 15 iNOS studied in this work. These results may be of great significance in the correlation of the non-covalent interaction in the inflammatory genes /cytokines with the aseptic loosening of implants. Ours is the first report on this kind of a non-covalent interaction studies on such inflammatory genes, generally expressed by macrophage during interaction with the prosthetic wear debris.     

Dose-dependent effects of Ni (II) ions on production of three inflammatory cytokines (TNF-α, IL-1β and IL-6), superoxide dismutase (SOD) and free radical NO by murine macrophage-like RAW264 cells with or without LPS-stimulation

The effect of Ni (II) ions on macrophages is not well understood. The purpose of this study was to examine the dose-dependent effects of Ni (II) ions up to 1,000 μmol/L on production of three inflammatory cytokines (TNF-α, IL-1β and IL-6), superoxide dismutase (SOD) and nitric oxide (NO) by murine macrophage-like RAW264 cells with (+) or without (−) lipopolysaccharide (LPS) -stimulation. Ni (II) ions caused LPS (−) RAW264 cells to slightly increase production of TNF-α and IL-6, proportionally to the Ni (II) ion concentration while IL-1β was not produced, and to slightly increase production of SOD and NO. It can be concluded that Ni (II) ions dose-dependently increased the inflammatory and oxidative stress conditions of LPS (−) RAW264 cells. LPS-stimulation caused RAW264 cells to produce in abundance the three inflammatory cytokines, SOD and NO. Ni (II) ions dose-dependently reduced the three cytokine quantities and NO amounts in LPS (+) RAW264 cells, while dose-independently increasing SOD amounts. It was noted that Ni (II) ions dose-dependently reduce the resistance power against bacteria of LPS (+) macrophages, because the production of volatile NO—bacteria killer is diminished proportionally to the Ni (II) ion concentration.     

Differential Regulation of cGMP Signaling in Human Melanoma Cells at Altered Gravity: Simulated Microgravity Down-Regulates Cancer-Related Gene Expression and Motility

Altered gravity is known to affect cellular function by changes in gene expression and cellular signaling. The intracellular signaling molecule cyclic guanosine-3^′,5^′-monophosphate (cGMP), a product of guanylyl cyclases (GC), e.g., the nitric oxide (NO)-sensitive soluble GC (sGC) or natriuretic peptide-activated GC (GC-A/GC-B), is involved in melanocyte response to environmental stress. NO-sGC-cGMP signaling is operational in human melanocytes and non-metastatic melanoma cells, whereas up-regulated expression of GC-A/GC-B and inducible NO synthase (iNOS) are found in metastatic melanoma cells, the deadliest skin cancer. Here, we investigated the effects of altered gravity on the mRNA expression of NOS isoforms, sGC, GC-A/GC-B and multidrug resistance-associated proteins 4/5 (MRP4/MRP5) as selective cGMP exporters in human melanoma cells with different metastatic potential and pigmentation. A specific centrifuge (DLR, Cologne Germany) was used to generate hypergravity (5 g for 24 h) and a fast-rotating 2-D clinostat (60 rpm) to simulate microgravity values ≤?0.012 g for 24 h. The results demonstrate that hypergravity up-regulates the endothelial NOS-sGC-MRP4/MRP5 pathway in non-metastatic melanoma cells, but down-regulates it in simulated microgravity when compared to 1 g. Additionally, the suppression of sGC expression and activity has been suggested to correlate inversely to tumor aggressiveness. Finally, hypergravity is ineffective in highly metastatic melanoma cells, whereas simulated microgravity down-regulates predominantly the expression of the cancer-related genes iNOS and GC-A/GC-B (shown additionally on protein levels) as well as motility in comparison to 1 g. The results suggest that future studies in real microgravity can benefit from considering GC-cGMP signaling as possible factor for melanocyte transformation.     

Chitosan/hyaluronic acid/plasmid-DNA nanoparticles encoding interleukin-1 receptor antagonist attenuate inflammation in synoviocytes induced by interleukin-1 beta

Synovial inflammation mainly resulting from interleukin-1 beta (IL-1β) plays a crucial role in the early and late stage of osteoarthritis. Recent progress in therapeutic gene delivery systems has led to promising strategies for local sustained target gene expression. The aim of this study was to design a nanoparticle made of chitosan (CS)/hyaluronic acid (HA)/plasmid-DNA (pDNA) encoding IL-1 receptor antagonist gene (pIL-1Ra) and furtherly use it to transfect the primary synoviocytes, and then investigate whether CS/HA/pIL-1Ra nanoparticles could make the synoviocytes overexpress functional IL-1Ra to attenuate inflammation induced by IL-1β. In this study, CS was modified with HA to generate CS/HA nanoparticles and then combined with pIL-1Ra to form CS/HA/pIL-1Ra nanoparticles. The physicochemical characteristics results showed that CS/HA nanoparticles exhibited an appropriate particle size (144.9?±?2.8?nm) and positive zeta potential (?+?28?mV). The gel retardation assay revealed that pDNA was effectively protected and released in a sustained manner more than 15 days. Cytotoxicity results showed that CS/HA/pIL-1Ra nanoparticles had a safe range (0-80?μg/ml) for the application to synoviocytes. RT-qPCR and western blot analysis demonstrated that CS/HA/pIL-1Ra nanoparticles were able to increase IL-1Ra expression in primary synoviocytes, and reduce the mRNA and protein levels of matrix metalloproteinase-3 (MMP-3), matrix metalloproteinase-13 (MMP-13), cyclooxygenase-2 (COX-2) and inducible nitric oxide synthase (iNOS) in IL-1β-induced synoviocytes. Our findings indicated that CS/HA/pIL-1Ra nanoparticles efficiently transfected synoviocytes and attenuated synovitis induced by IL-1β, which will provide a potential strategy for OA synovitis.

Open image in new window

     

Anti‐inflammatory Properties of Cerium Oxide Nanoparticles

The valence and oxygen defect properties of cerium oxide nanoparticles (nanoceria) suggest that they may act as auto‐regenerative free radical scavengers. Overproduction of the free radical nitric oxide (NO) by the enzyme inducible nitric oxide synthase (iNOS) has been implicated as a critical mediator of inflammation. NO is correlated with disease activity and contributes to tissue destruction. The ability of nanoceria to scavenge free radicals, or reactive oxygen species (ROS), and inhibit inflammatory mediator production in J774A.1 murine macrophages is investigated. Cells internalize nanoceria, the treatment is nontoxic, and oxidative stress and pro‐inflammatory iNOS protein expression are abated with stimulation. In vivo studies show nanoceria deposition in mouse tissues with no pathogenicity. Taken together, it is suggested that cerium oxide nanoparticles are well tolerated in mice and are incorporated into cellular tissues. Furthermore, nanoceria may have the potential to reduce ROS production in states of inflammation and therefore serve as a novel therapy for chronic inflammation.     

Detection of nitric oxide release from single neurons in the pond snail, Lymnaea stagnalis

Multiple film-coated nitric oxide sensors have been fabricated using Nafion and electropolymerized polyeugenol or o-phenylenediamine on 30-microm carbon fiber disk electrodes. This is a rare study that utilizes disk electrodes rather than the widely used protruding tip microelectrodes in order to measure from a biological environment. These electrodes have been used to evaluate the differences in nitric oxide release between two different identified neurons in the pond snail, Lymnaea stagnalis. These results show the first direct measurements of nitric oxide release from individual neurons. The electrodes are very sensitive to nitric oxide with a detection limit of 2.8 nM and a sensitivity of 9.46 nA microM-1. The sensor was very selective against a variety of neurochemical interferences such as ascorbic acid, uric acid, and catecholamines and secondary oxidation products such as nitrite. Nitric oxide release was measured from the cell bodies of two neurons, the cerebral giant cell (CGC) and the B2 buccal motor neuron, in the intact but isolated CNS. A high-Ca2+/high-K+ stimulus was capable of evoking reproducible release. For a given stimulus, the B2 neuron released more nitric oxide than the CGC neuron; however, both cells were equally suppressed by the NOS inhibitor l-NAME.     

Biomechanical regulation of vascular smooth muscle cell functions: from in vitro to in vivo understanding

Vascular smooth muscle cells (VSMCs) have critical functions in vascular diseases. Haemodynamic factors are important regulators of VSMC functions in vascular pathophysiology. VSMCs are physiologically active in the three-dimensional matrix and interact with the shear stress sensor of endothelial cells (ECs). The purpose of this review is to illustrate how haemodynamic factors regulate VSMC functions under two-dimensional conditions in vitro or three-dimensional co-culture conditions in vivo. Recent advances show that high shear stress induces VSMC apoptosis through endothelial-released nitric oxide and low shear stress upregulates VSMC proliferation and migration through platelet-derived growth factor released by ECs. This differential regulation emphasizes the need to construct more actual environments for future research on vascular diseases (such as atherosclerosis and hypertension) and cardiovascular tissue engineering.     

Porous alumina ceramics prepared by slurry infiltration of expanded polystyrene beads

To produce highly porous MgO-doped alumina (Al₂O₃) ceramics, expanded polystyrene (EPS) beads were packed as a pore former and well-dispersed alumina slurry was used to infiltrate the pore space in the EPS bead compacts. The alumina particle-EPS bead green compacts were then heated to 1550°C in air to burn out the pore former and subsequently densify the MgO-doped alumina struts. The porous Al₂O₃ ceramics were featured with uniformly distributed open pore structures with porosities ranging from 72 to 78% and a pore interconnectivity of about 96%. The macropore size and the pore window size could be controlled by adjusting the size of the EPS beads and the contacting area between the EPS beads. The compressive strengths of the porous Al₂O₃ ceramics were in the range of 5.5–7.5 MPa, similar to those of cancellous bones (2–12 MPa). The porous alumina ceramics were further made bioactive after the dip coating of a sol-gel derived 58 S bioglass powder, followed by sintering at 1200°C.     

Solid-phase extractants based on taunit carbon nanotubes for actinide and REE preconcentration from nitric acid solutions

The sorption properties of solid-phase extractants (SPEs) prepared by impregnation of Taunit carbon nanotubes with adducts of diphenyl(dibutylcarbamoylmethyl)phosphine oxide (CMPO) and tri-n-octylphosphine oxide (TOPO) in HNO₃ solutions were studied. The SPEs exhibit high ability to sorb U(VI), Pu(IV), Np(V), Am(III), and Eu(III) from nitric acid solutions, with good kinetic properties. The impregnation conditions and distribution coefficients of the radionuclides in their recovery from 3 M HNO₃ were determined. The possibility of preparing SPEs by Taunit impregnation in HNO₃ solutions with adducts of tributyl phosphate (TBP) and N,N′-dimethyl-N,N′-dioctylhexylethoxymalonamide (DMDOHEMA) and with Cyphos IL-101 phosphonium ionic liquid was demonstrated.     

Fluorescence monitoring of ATP-stimulated, endothelium-derived nitric oxide production in channels of a poly(dimethylsiloxane)-based microfluidic device

Intracellular nitric oxide (NO) production in a microfluidic endothelium is detected using fluorescence microscopy. Bovine pulmonary artery endothelial cells (bPAECs) were loaded with the fluorescence probe diaminodifluorofluorescein diacetate (DAF-FM DA), and the subsequent fluorescent DAF-FM DA/NO adduct was measured. Solutions of bradykinin, a well-known stimulus of endothelium-derived NO, activated nitric oxide synthase (NOS) in the immobilized bPAECs. This activation was inhibited using l-nitro arginine methyl ester (L-NAME), a competitive inhibitor of NOS. Importantly, the NO production was also stimulated with adenosine triphosphate (ATP) using concentrations as low as 1 microM. Previous reports on stimulating NO production using an immobilized endothelium in microfluidic channels were limited by the requirement of ATP concentrations of at least 100 microM, a value that is not physiologically relevant. The ability to monitor NO production with ATP concentrations that are similar to in vivo levels of ATP in the microcirculation represents a major advance in the use of microfluidic technology as an in vitro model of the microcirculation.     

The formation of a complex between calmodulin and neuronal nitric oxide synthase is determined by ESI-MS.

Calmodulin (CaM) is an acidic ubiquitous calcium binding protein, involved in many intracellular processes, which often involve the formation of complexes with a variety of protein and peptide targets. One such system, activated by Ca2+ loaded CaM, is regulation of the nitric oxide synthase (NOS) enzymes, which in turn control the production of the signalling molecule and cytotoxin NO. A recent crystallographic study mapped the interaction of CaM with endothelial NOS (eNOS) using a 20 residue peptide comprising the binding site within eNOS. Here the interaction of CaM to the FMN domain of neuronal nitric oxide synthase (nNOS) has been investigated using electrospray ionization mass spectrometry (ESI-MS). The 46 kDa complex formed by CaM-nNOS has been retained in the gas-phase, and is shown to be exclusively selective for CaM.4Ca2+. Further characterization of this important biological system has been afforded by examining a complex of CaM with a 22 residue synthetic peptide, which represents the linker region between the reductase and oxygenase domains of nNOS. This nNOS linker peptide, which is found to be random coil in aqueous solution by both circular dichroism and molecular modelling, also exhibits great discrimination for the form of CaM loaded with 4[Ca2+]. The peptide binding loop is presumed to be configured to an alpha-helix on binding to CaM as was found for the related eNOS binding peptide. Our postulate is supported by gas-phase molecular dynamics calculations performed on the isolated nNOS peptide. Collision induced dissociation was employed to probe the strength of binding of the nNOS binding peptide to CaM.4Ca2+. The methodology taken here is a new approach in understanding the CaM-nNOS binding site, which could be employed in future to inform the specificity of CaM binding to other NOS enzymes.     

Bone-like apatite coating on Mg-PSZ/Al2O3 composites using bioactive systems

A biomimetic method was used to promote bioactivity on zirconia/alumina composites. The composites were composed of 80 vol% Mg-PSZ and 20 vol% Al₂O₃. Samples of these bioinert materials were immersed in simulated body fluid (SBF) for 7 days on either a bed of wollastonite ceramics or bioactive glass. After those 7 days, the samples were immersed in a more concentrated solution (1.4 SBF) for 14 days. Experiments were also performed without using a bioactive system during the first stage of immersion. A bone-like apatite layer was formed on the surface of all the materials tested, using wollastonite the bioactive layer was thicker and its morphology was close to that observed on the existing bioactive systems. A thinner apatite layer consisting of small agglomerates was obtained using bioactive glass. The thickness of the ceramic layers was within the range of 15 to 30 μm.     

Nucleation and growth mechanism of apatite on a bioactive and degradable ceramic/polymer composite with a thick polymer layer

Nucleation and growth mechanism of apatite on a bioactive and degradable PLLA/SiO₂–CaO composite with a thick PLLA surface layer were investigated compared to that on a bioactive but non-degradable polyurethane (PU)/SiO₂–CaO composite with a thick PU surface layer. The bioactive SiO₂–CaO particles were made by a sol–gel method from tetraethyl orthosilicate and calcium nitrate tetrahydrate under acidic condition followed by heat treatment at 600 °C for 2 h. The PLLA/SiO₂–CaO and PU/SiO₂–CaO composites were then prepared by a solvent casting method which resulted in thick PLLA and PU surface layers, respectively, due to precipitation of SiO₂–CaO particles during the casting process. Two composites were exposed to SBF for 1 week and this exposure led to form uniform and complete apatite coating layer on the PLLA/SiO₂–CaO composite but not on the PU/SiO₂-CaO composite. These results were interpreted in terms of the degradability of the polymers. A practical implication of the results is that a post-surface grinding or cutting processes to expose bioactive ceramics to the surface of a composite with a thick biodegradable polymer layer is not required for providing apatite forming ability, which has been considered as one of the pragmatic obstacles for the application as a bone grafting material.     

Electrical conduction in La<Subscript>0.9</Subscript>Ba<Subscript>0.1</Subscript>Er<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Mg<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript>3−α</Subscript> ceramics

Doubly doped LaErO₃ ceramics, La_0.9Ba_0.1Er_1−x Mg _x O_3−α (x = 0.05, 0.10, 0.15, 0.20), were synthesized by solid-state reaction method and characterized by X-ray diffraction (XRD). The samples have a single orthorhombic perovskite-type structure. The conduction behavior was investigated using various electrochemical methods including AC impedance spectroscopy, gas concentration cell, isotope effect of hydrogen, and hydrogen electrochemical permeation (pumping) in the temperature range of 500–1000 °C. The results indicated that specimens were pure ionic conductors under low oxygen partial pressure (about 10⁻⁷–10⁻²⁰ atm) and mixed conductors of proton, oxide ion, and electron hole under high oxygen partial pressure (about 10⁻⁵–1 atm). The pure ion conduction of the ceramics in hydrogen atmosphere was confirmed by electromotive force method of hydrogen concentration cell, and the observed emf values coincided well with the theoretical ones. The conductivity in H₂O–Ar atmosphere was higher than that in D₂O–Ar atmosphere, exhibiting an obvious isotope effect and proton conduction in water vapor containing atmosphere. It has been confirmed by electrochemical hydrogen permeation (hydrogen pumping) experiment that the ceramics were mainly proton conductors in hydrogen containing atmosphere. Whereas in dry oxygen-containing atmosphere, observed emf values of the oxygen concentration cell were far lower than the theoretical ones, indicating that the ceramics were mixed conductors of electron hole and oxide ion.     

Temperature dependence of the elastic and inelastic moduli of YBa2Cu3O7−δ ceramics

Elastic and inelastic moduli of the superconducting yttrium-barium oxide ceramics YBa₂Cu₃O_7−δ (YBCO) were studied using the ultrasonic resonance technique. In the range from room temperature up to the temperature of the ortho-tetra phase transition, the elastic and inelastic moduli of YBCO samples exhibit a number of anomalies. It is shown that these features are related to the behavior of active oxygen in the ceramics, the phase inhomogeneity of the material, and the phase transitions.     

RETRACTED ARTICLE: Characteristics of porous zirconia coated with hydroxyapatite as human bones

Since hydroxyapatite has excellent biocompatibility and bone bonding ability, porous hydroxyapatite ceramics have been intensively studied. However, porous hydroxyapatite bodies are mechanically weak and brittle, which makes shaping and implantation difficult. One way to solve this problem is to introduce a strong porous network onto which hydroxyapatite coating is applied. In this study, porous zirconia and alumina-added zirconia ceramics were prepared by ceramic slurry infiltration of expanded polystyrene bead compacts, followed by firing at 1500°C. Then slurry of hydroxyapatite-borosilicate glass mixed powder was used to coat the porous ceramics, followed by firing at 1200°C. The porous structures without the coating had high porosities of 51–69%, high pore interconnectivity, and sufficiently large pore window sizes (300–500 μm). The porous ceramics had compressive strengths of 5·3∼36·8 MPa, favourably comparable to the mechanical properties of cancellous bones. In addition, porous hydroxyapatite surface was formed on the top of the composite coating, whereas a borosilicate glass layer was found on the interface. Thus, porous zirconia-based ceramics were modified with a bioactive composite coating for biomedical applications.     

Numerical Analysis of Heat Transport Behavior in the Ferromagnetic Metallic State of La0.80Ca0.20MnO3 Manganites

The lattice contribution to the thermal conductivity (κ_ph) in La_0.80Ca_0.20 MnO₃ manganites is discussed within the Debye-type relaxation rate approximation in terms of the acoustic phonon frequency and relaxation time. The theory is formulated when heat transfer is limited by the scattering of phonons from defects, grain boundaries, charge carriers, and phonons. The lattice thermal conductivity dominates in La–Ca–MnO manganites and is an artifact of strong phonon-impurity and -phonon scattering mechanisms in the ferromagnetic metallic state. The electronic contribution to the thermal conductivity (κ_e) is estimated following the Wiedemann–Franz law. This estimate sets an upper bound on κ_e, and in the vicinity of the Curie temperature (240 K) κ_e is about 1% of total heat transfer of manganites. Another important contribution in the metallic phase should come from spin waves (κ_m). It is noticed that κ_m increases with a T² dependence on the temperature. These channels for heat transfer are algebraically added and κ_tot develops a broad peak at about 55 K, before falling off at lower temperatures. The behavior of the thermal conductivity in manganites is determined by competition among the several operating scattering mechanisms for the heat carriers and a balance between electron, magnon, and phonon contributions. The numerical analysis of heat transfer in the ferromagnetic metallic phase of manganites shows similar results as those revealed from experiments.      

Biological control of apatite growth in simulated body fluid and human blood serum

The surface transformation reactions of bioactive ceramics were studied in vitro in standard K9-SBF solution and in human blood serum (HBS)—containing simulated body fluid (SBF). The calcium phosphate ceramics used for this study were stoichiometric hydroxyapatite (HA), β-tricalcium phosphate (β-TCP) and brushite. Immersion of each calcium phosphate tested in this study, in simulated body fluid, led to immediate surface precipitation of apatite. The use of HBS resulted in a delay in the onset of precipitation and a significant inhibition of the dissolution reaction normally observed for brushite in solution. However, apatite formation still occurred. The use of HBS and SBF in this investigation, which has shown the ability to induce similar crystal growth as that observed in vivo, suggests that there is scope for the use of serum proteins in simulated body fluid in order to create a protein-rich surface coating on biomedical substrates.