Ti6Al4V的微磨粒磨损研究

研究了医用Ti6Al4V合金在蒸馏水中的微磨粒磨损行为,考察了载荷、滑行距离、料浆浓度和转速对微磨粒磨损规律的影响,并对微磨粒磨损机制进行了讨论。结果表明:随载荷、滑行距离和料浆浓度的增加,Ti6Al4V合金的磨损量增加,磨损机制由三体磨损转变为混合磨损。     

Micro-scale abrasive wear testing of duplex and non-duplex (single-layered) PVD (Ti,Al)N, TiN and Cr–N coatings

A micro-scale abrasive wear test, based on ball-cratering, has been used to evaluate the wear resistance of duplex and non-duplex (Ti,Al)N, TiN and Cr–N coatings. The term duplex is used here when plasma nitriding is followed by PVD coating. Coatings without the plasma nitriding stage are termed single-layered. Coating properties were evaluated by surface profilometry, hardness and scratch testing. All duplex coatings showed higher micro-abrasive wear resistance than their single-layered counterparts, with the duplex (Ti,Al)N coating achieving the best performance. After a certain number of ball revolutions, the coating material became worn through, exposing the substrate material. After this point, the presence of a hard nitrided case diminished the scratching action of the SiC abrasive particles. The experimental results also indicate that the choice of the PVD coating plays an important role in improving the micro-abrasive wear resistance. Apart from single-layered and duplex Cr–N coatings, all the other coating systems provided a higher micro-abrasive wear resistance than the uncoated substrate (hardened AISI H13 steel). The poor abrasive wear resistance recorded for the single-layered and duplex Cr–N coatings could be attributed to the hardness of the Cr–N being much lower than that of the SiC abrasive particles, which caused tearing of the coating with subsequent delamination. The wear pattern observed was found to change from surfaces characterised by grooves (uncoated substrate, single-layered TiN and Cr–N systems and duplex Cr–N system) to surfaces which exhibited multiply indented surfaces (single-layered and duplex (Ti,Al)N systems), indicating a transition between wear mechanisms. This transition was found to be dependent on the ratio between the hardness of the SiC abrasive particles and surface (coating) or subsurface hardness. By decreasing this ratio, the ability of the SiC abrasive particles to scratch the composite surface was reduced and the resistance to micro-scale abrasion was improved.     

Severe-to-Mild Wear Transition of Titanium Alloys as a Function of Temperature

Dry sliding wear behaviors of Ti–6Al–4V and Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloys (code-named TC4 and TC11, respectively) against AISI 52100 steel under a load of 50–250 N at 25–600 °C were systematically investigated. For two titanium alloys, a severe-to-mild wear transition occurred with an increase in temperature. The critical transition temperatures of TC4 and TC11 alloys were 400 and 300 °C, respectively. Below the critical temperature, titanium alloys showed poor wear performance. As the temperature surpassed the critical temperature, the extremely low wear rates demonstrated excellent elevated-temperature wear performance of titanium alloys in the titanium alloy/steel tribo-system. The wear transition was characterized with the appearance of continuous, hard tribo-layer containing more oxides, especially Fe₂O₃, which showed a pronounced wear-reduced role. Adhesive and abrasive wear predominated in the severe wear regime; oxidative mild wear prevailed in the mild wear regime. Adhesive wear, abrasive wear and oxidative mild wear cooperated at the critical transition temperatures.     

Ti6A14V的微磨粒磨损研究

研究了医用Ti6A14V合金在蒸馏水中的微磨粒磨损行为，考察了载荷、滑行距离、料浆浓度和转速对微磨粒磨损规律的影响，并对微磨粒磨损机制进行了讨论。结果表明：随载荷、滑行距离和料浆浓度的增加，Ti6A14V合金的磨损量增加，磨损机制由三体磨损转变为混合磨损。     

Wear resistant multilayer nanocomposite WC1−x/C coating on Ti–6Al–4V titanium alloy

A significant improvement of tribological properties on Ti–6Al–4V has been achieved by developed in this study multilayer treatment method for the titanium alloys. This treatment consists of an intermediate 2 μm thick TiC_xN_y layer which has been deposited by the reactive arc evaporation onto a diffusion hardened material with interstitial O or N atoms by glow discharge plasma in the atmosphere of Ar+O₂ or Ar+N₂. Subsequently, an external 0.3 μm thin nanocomposite carbon-based WC_1−x/C coating has been deposited by a reactive magnetron sputtering of graphite and tungsten targets. The morphology, microstructure, chemical and phase compositions of the substrate material after treatment and coating deposition have been investigated with use of AFM, SEM, EDX, XRD, 3D profilometry and followed by tribological investigation of wear and friction analysis. An increase of hardness in the diffusion treated near-surface zone of the Ti–6Al–4V substrate has been achieved. In addition, a good adhesion between the intermediate gradient TiC_xN_y coating and the Ti–6Al–4V substrate as well as with the external nanocomposite coating has been obtained. Significant increase in wear resistance of up to 94% when compared to uncoated Ti–6Al–4V was reported. The proposed multilayer system deposited on the Ti–6Al–4V substrate is a promising method to significantly increase wear resistance of titanium alloys.     

Tribological behaviors of Ti–6Al–4V modified by chemical methods

In order to improve the tribological properties of titanium-based implants, sodium hydroxide (NaOH), hydrogen peroxide (H₂O₂) solutions, sol–gel hydroxyapatite (HA) film, thermal treatment and combined methods of NaOH solution/HA film, H₂O₂ solution/HA film are used to modify the surfaces of Ti–6Al–4V (coded TC4). The chemical states of some typical elements in the modified surfaces were detected by means of X-ray photoelectron spectroscopy (XPS). The tribological properties of modified surfaces sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the results, complex surfaces with varied components are obtained. All the methods are effective in improving the wear resistance of Ti–6Al–4V in different degrees. Among all, the surface modified by the combined method of NaOH solution/HA film gives the best tribological performances. The friction coefficient is also greatly reduced by the modification of NaOH solution. The order of the wear resistance under 3 N is as following: Ti–NaOH–HA>Ti–NaOH>Ti–HA>Ti–H₂O₂–HA>Ti–H₂O₂ >Ti–500; under 1 N is Ti–HA, Ti–NaOH–HA>Ti–NaOH. For Ti–H₂O₂, a very low friction coefficient and long wear life over 2000 passes is obtained under 1 N. SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro–crack dominate the wear of Ti–HA; slight abrasive wear dominate the wear mechanism of Ti–NaOH and microfracture and abrasive wear for Ti–NaOH–HA and Ti–H₂O₂–HA, while the sample modified by thermal treatment is characterized by sever fracture. The superior friction reduction and wear resistance of HA films are greatly attributed to the slight plastic deformation of the film. NaOH solution is superior in improving the wear resistance and decreasing the friction coefficient under relative higher load (3 N) and H₂O₂ is helpful to reduce friction and wear under relatively lower load (1 N). Combined method of Ti–NaOH–HA is suggested to improve the wear resistance of Ti–6Al–4V for medial applications under fretting situations.     

Slurry Erosion Wear Resistance and Impact-Induced Phase Transformation of Titanium Alloys

Erosion wear resistance and impact-induced phase transformation of titanium alloys TA2 (pure Ti), TC4 (Ti–6Al–4V) and TC11 (Ti–6.5Al–3.5Mo–1.5Zr–0.3Si) were investigated using a slurry jet tester. The slurry erosion wear resistance of TA2 is comparable to that of 304 stainless steel, especially at the impingement angle 90°. Although TC4 and TC11 have higher hardness, TA2 possesses the best erosion wear resistance except TC11 at 15°. With the increasing erosion time, the eroded surface hardness of TC11 at the impingement angle 90° increases and then decreases, while the volume loss rate drops in the first 15 min, then increases until 30 min, and then slightly decreases again. With XRD characterization and SEM observation, erosion-induced phase transformation from metastable β-phase to α-phase is proved on the surface of titanium alloy TC11. And the thickness of visible phase transformation layer is about 10 μm. Phase transformation influences the erosive wear mechanism of titanium alloys. At the impingement angle of 30°, the material removal of TC4 and TC11 can be described as micro-plowing and lip extruding, while plowing mark is not a typical surface morphology of TA2, indicating a better work-harden ability. So, stabilizing β-phase can be an effective way to improve the erosion wear resistance of titanium alloys.     

Study of abrasive wear phenomena in dry and slurry 3-body conditions

Machinery and equipment used in abrasive environments, such as the mining industry, suffer from severe wear. In order to understand wear and to prolong the life time of the machinery, it is important to understand how materials respond to wear depending on the environmental and tribological conditions imposed.This paper exposes a comparative study between the influence of two abrasive environments (dry and slurry) on hard particle coatings and steels. To study this, the 3-body wear behaviour was evaluated in a dry environment using a continuous abrasion test (CAT) and in a slurry environment using a slurry steel wheel abrasion test (SSWAT) method. Both tests are capable of experimentally modelling the high stress wear at 45 N and 216 N, using quartz sand as an abrasive. The tests were performed on two types of coatings processed by sintering and hardfacing and martensitic steel was used as a reference. The wear was indicated as volume loss by measuring the samples before and after the tests. Furthermore, the specific wear energy was calculated in order to have a fundamental understanding about the material's response to wear. A correlation between the wear rate and the particle brakeage index (PBI) was done for the dry conditions using different loads, in order to explain the interdependence between the two parameters and the change in the wear mechanism between the two loads. The influence of load on the wear of the materials showed different wear mechanisms on coatings compared to the steel in the same environmental conditions. However, a change in wear mechanism at different load levels was observed, which might be directly dependent on the change of the particle's motion from sliding to rolling combined with the change in their shape and size. The results showed that the need to study the influence of different abrasive conditions on the material wear is crucial in order to improve the lifetime and the cost efficiency of the machinery used in such environments. The hard-particle coatings showed comparatively low wear rates promising a great potential in improving the lifetime of industrial equipments in different environments.     

Biotribological properties of Ti/TiB2 multilayers in simulated body solution

Ti/TiB₂ multilayers with various modulation ratios were prepared by magnetron sputtering on biomedical titanium alloy Ti6Al4V. The tribological properties of the multilayers sliding against ultra-high molecular weight polyethylene under lubrication with Hank׳s solution were also investigated. The results demonstrated that the tribological properties strongly depended on the modulation ratios of multilayers. The coefficient of friction of multilayers with a modulation ratio of 1:5 was 0.1, a reduction by 28.6%; the wear volume loss of UHMWPE decreased by almost one order of magnitude compared to that of Ti6Al4V alloy, exhibiting excellent anti-friction and anti-wear properties. The oxidation wear of Ti6Al4V alloy could be restrained effectively and converted to abrasion wear and/or adhesive wear by the laminate structures in the multilayers, suggesting that this material may serve as a potential candidate for the surface modification of artificial joints.     

Wear analysis of Cu–Al coating on Ti–6Al–4V substrate under fretting condition

Fretting behavior of Cu–Al coating on Ti–6Al–4V substrate was investigated with and without fatigue load. Soft and rough Cu–Al coating resulted in abrasive wear and a large amount of debris remained at the contact surface, which caused an increase in tangential force during the fretting test under gross slip condition. Fretting in the partial slip condition also showed the wear of coating. To characterize wear, dissipated energies during fretting were calculated from fretting loops and wear volumes were obtained from worn surface profiles. Energy approach of wear analysis showed a linear relationship between wear volume and accumulated dissipated energy. This relationship was independent of fatigue loading condition and extended from partial slip to gross slip regimes. As an alternate but simple approach for wear analysis, accumulated relative displacement range was correlated with the wear volume. This also resulted in a linear relationship as in the case of accumulated dissipated energy suggesting that the accumulated relative displacement range can be used as an alternative parameter for dissipated energy to characterize the wear. When the maximum wear depth was equal to the thickness of Cu–Al coating, harder Ti–6Al–4V substrate inhibited further increase in wear depth. Only when a considerable energy was supplied through a large value of the applied displacement, wear in the substrate material could occur beyond the thickness of coating.     

Sliding friction and wear of Cu–graphite against 2024, AZ91D and Ti6Al4V at different speeds

Cu–graphite composite fabricated by powder metallurgy art is no longer novel material. However, it might be a versatile self-lubricating material sliding against different metals and alloys. In this connection, understanding towards its tribological behavior and wear mechanism is very important. Sliding tribological behaviors of Cu–graphite composite against different counterparts, specified as 2024 aluminium alloy, AZ91D magnesium alloy, and Ti6Al4V titanium alloy, were investigated over varied sliding speeds at room temperature in air. The friction and wear tests were conducted on a pin-on-disk tribo-meter. Tribological performance of Cu–graphite composite strongly depended on its counterpart materials. Cu–graphite composite could provide friction reduction in sliding against 2024 and Ti6Al4V. Cu–graphite composite was a good self-lubricating material in sliding against AZ91D at low speeds but not at 0.25 and 0.50 m/s. Wear mechanism of Cu–Gr composite was related to the transfer, counter-transfer, mechanical mixing and tribo-oxidation at tribo-interface. Sliding speed had influences on tribo-interface and thereby wear mechanism. Finally, the effects of naturally occurred oxide film and sliding speed were discussed.     

Friction and wear of titanium alloys sliding against metal, polymer, and ceramic counterfaces

Recent advances in lower-cost processing of titanium, coupled with its potential use as a light weight material in engines and brakes has renewed interest in the tribological behavior of titanium alloys. To help establish a baseline for further studies on the tribology of titanium against various classes of counterface materials, pin-on-disk sliding friction and wear experiments were conducted on two different titanium alloys (Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo). Disks of these alloys were slid against fixed bearing balls composed of 440C stainless steel, silicon nitride, alumina, and polytetrafluoroethylene (PTFE) at two speeds: 0.3 and 1.0 m/s. The friction coefficient and wear rate were lower at the higher sliding speed. Ceramic sliders suffered unexpectedly higher wear than the steel slider. The wear rates, ranked from the highest to the lowest, were alumina, silicon nitride, and steel, respectively. This trend is inversely related to their hardness, but corresponds to their relative fracture toughness. Comparative tests on a Type 304 stainless steel disk supported the fracture toughness dependency. Energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) analyses confirmed the tendency of Ti alloys to transfer material to their counterfaces and suggested possible tribochemical reactions between the ceramic sliders and Ti alloy disks. These reaction products, which adhere to the ceramic sliders, may degrade the mechanical properties of the contact areas and result in high wear. The tribochemical reactions along with the fracture toughness dependency helped explain the high wear on the ceramic sliders.     

Response of Ti–6Al–4V and Ti–24Al–11Nb alloys to dry sliding wear against hardened steel

Titanium alloys have been of great interest in recent years because of their very attractive combination of high strength, low density and corrosion resistance. Application of these alloys in areas where wear resistance is also of importance calls for thorough investigations of their tribological properties. In this work, Ti–6Al–4V and Ti–24Al–11Nb alloys were subjected to dry sliding wear against hardened-steel counter bodies and their tribological response was investigated. A pin-on-disc type apparatus was used with a normal load of 15–45N and sliding speed of 1.88 ms⁻¹. In the steady state, it was demonstrated that Ti–24Al–11Nb had a substantially higher wear resistance (about 48 times) than that of the Ti–6Al–4V alloy tested under a normal load of 45 N. Severe delamination is found to be responsible for the low wear resistance of Ti-6Al-4V. In the case of Ti–24Al–11Nb, two wear mechanisms have been suggested: delamination with a lower degree of severity and oxidative wear. It is thought that the ability of Ti–24Al–11Nb to form a protective oxide layer during wear results in a much lower wear rate in this alloy.     

Tribological Behaviour of Pure Ti with a Nanocrystalline Surface Layer Under Different Loads

Surface mechanical attrition treatment (SMAT), a novel surface severe plastic deformation method, was carried out for titanium (Ti) to create a gradient-structured Ti (SMAT Ti). The tribological behaviour was studied under different loads and dry sliding conditions. The results showed that the deformation layer of SMAT Ti was about 160 μm. The friction and wear results showed that the wear resistance of SMAT Ti was enhanced compared to the coarse-grained (CG) counterpart. SMAT Ti showed abrasive wear under 1 and 5 N, and exhibited abrasive and adhesive wear under 2 N. While CG Ti showed abrasive and adhesive wear under 1–2 N, and exhibited abrasive wear under 5 N for the work hardening effects.     

Effect of cold deformation on the abrasive resistance of coatings with applications in the mining industry

Machinery components of the mining industry are often involved in severe wear processes. This is the case of the support wheels of the crawler track of the excavators in the open cast mine. Surface coating technologies are essential to improve the surface performance of such components. In this work, the effect of cold deformation on the wear resistance of several Fe–Cr–Mn alloys welding coated over a steel substrate is studied. After being coated, the specimens were pressed by means of a block hammer which produced surface distortion and thickness variation. This deformation process generates micro structural changes and material which may improve the abrasive wear resistance. Abrasion wear tests were carried out based on the standard test method for conducting wet sand/rubber wheel abrasion tests (ASTM G105-89).     

Micro-abrasion wear testing of triode plasma diffusion and duplex treated Ti–6Al–4V alloy

In this paper micro-abrasion wear testing is used to evaluate the wear resistance of triode plasma diffusion-treated, single-layered TiN-, CrAlN-, and WC/C-coated and duplex-diffusion and coated Ti–6Al–4V under uniform three-body rolling abrasion. Nanoindentation, Knoop microhardness, mechanical surface profilometry, optical microscopy, scanning electron microscopy and atomic force microscopy, were used to characterise the surfaces under investigation. Optimum testing conditions for rolling abrasion were established by varying the test parameters and resultant severity of contact. Very low normal loads and high volume fractions of particles in the abrasive slurry are necessary to obtain predictable and reproducible results. Relatively coarse SiC abrasive particles, having a mean diameter of around 3 μm, appear more suitable for micro-abrasion testing of the samples investigated, compared to finer Al₂O₃ particles. Problems associated with the measurement of the scar volume and subsequent calculation of the wear rate for hard coatings deposited on relatively soft metals like titanium are identified, and suitable testing and measurement techniques are suggested. Three-dimensional wear scar maps generated by mechanical stylus profilometry were used to measure the wear volumes. Under the test conditions used, wear coefficients can be determined from perforating and non-perforating tests, although perforating tests provide more consistent results. Triode plasma diffusion treatments, plasma-assisted (PA) PVD TiN and PAPVD CrAlN can reduce the specific wear rate of Ti–6Al–4V, while PACVD-based WC/C coatings do not provide suitable protection against abrasive wear. The combination of triode plasma oxynitriding diffusion treatments and PVD coatings to create duplex treatments can also lead to further reductions in the coating wear coefficient when compared to non-duplex coatings deposited on non-pretreated substrates.     

Improvement in tribological performances of magnesium alloy using amide compounds as lubricating additives during sliding

The tribological characteristics of a magnesium alloy, AZ91D (die-casting), are investigated in a sliding lubricating system using various amide compounds as lubricating additives on a Timken type tester against a bearing steel (AISI52100) ring. Results indicate that a significant improvement in the tribological performance exists using the amide compounds as additives. The number of amido group (–CONH₂) in additive molecules and the molecular structure of amide compounds have significant effect on the tribological characteristics of magnesium alloy. Electromicroscopy reveals that the mild abrasive wear is a predominant wear mechanism of magnesium alloy using an amide additive while the dominated wear mechanism is a severe abrasive wear with severe material deformation using only base oil. Observation shows the formation of boundary film on the magnesium alloy. XPS analysis suggests the occurrence of tribo-chemical reactions between Mg and amide compounds with the formation of chemically stable compound (or complex) of magnesium and amide, as well as the formation of friction polymer.     

Tribological properties of selected PVD coatings when slid against ductile materials

In this paper, a physical vapour deposited (PVD) deposited TiB₂ coating is compared in dry sliding with commercial PVD titanium nitride (TiN), titanium aluminium nitride (TiAlN) and titanium carbonitirde (TiCN) as to frictional properties and tendency of counter material pick-up. The aim is to investigate if the superior behaviour of the TiB₂ coating experienced in severe sliding applications against aluminium alloys can be extended to other materials with a similarly poor tribological characteristics.A new tribological test for sliding contact has been used. The test configuration involves two crossed elongated cylindrical test specimens which are forced to slide axially against each other at a constant sliding speed and a gradually increasing normal load, while recording the friction. The evaluation is performed by correlating the friction history with the width, topography and composition of the sliding tracks as detected by optical and scanning electron microscopy.Coated cemented carbide (CC) test cylinders have been slid against cylinders of a Ti alloy (Ti–6Al–4V), an Al alloy (Al 7075) and Inconel 718. It was shown that the TiB₂ surface displayed superior friction and anti-sticking properties, when tested against the aluminium alloy. Against the Ti and Inconel alloys no major difference between the coatings could be found. Instead, it is concluded that the friction coefficient is determined by the plastic properties of the counter material since a complete transfer layer instantly builds up on the coating.It proved possible to estimate the friction force from the width of the sliding tracks, the Vickers hardness of the counter material and simple plastic considerations. This estimation also verifies the unexpectedly low friction of all coatings against the Ti alloy.     

Torsional fretting wear of a biomedical Ti6Al7Nb alloy for nitrogen ion implantation in bovine serum

Ti6Al7Nb is a high-strength titanium alloy used in replacement hip joints that possesses the excellent biocompatibility necessary for surgical implants. Ti6Al7Nb treated with nitrogen gas (N₂) plasma immersion ion implantation–deposition (PIII–D) was investigated. Torsional fretting wear tests of untreated and nitrogen-ion-implanted Ti6Al7Nb alloys against a Zr₂O ball (diameter 25.2 mm) were carried out under simulated physiological conditions (serum solution) in a torsional fretting wear test rig. Based on the analyses of the frictional kinetics behavior, the observation of 3D profiles, SEM morphologies and surface composition analyses, the damage characteristics of the surface modification layer and its substrate are discussed in detail. The influence of nitrogen ion density on the implantation and torsional angular displacement amplitudes were investigated. The results indicated that ion implantation layering can improve resistance to torsional fretting wear and thus has wide potential application for the prevention of torsional fretting damage in artificial implants. The damage mechanism prevented by the ion implantation layer on the Ti6Al7Nb alloy is a combination of oxidative wear, delamination and abrasive wear. An increase in ion implantation concentration inhibited detachment by delamination.     

生物医用钛合金TiN涂层微磨粒磨损及耐蚀性初步研究

对生物医用Ti6Al4V合金表面TiN涂层机械力学性能进行了研究,在分析力学性能的基础上,考察了TiN涂层在蒸馏水和Hank’s模拟体液中的耐磨性,并在Hank’s模拟人体体液中研究了TiN涂层在静态环境中的腐蚀行为。结果表明:在Ti6Al4V合金表面沉积TiN涂层后,其耐磨性和耐蚀性大大提高,有利于改善钛合金在人体环境中的使用寿命。