共查询到20条相似文献,搜索用时 125 毫秒
1.
2.
3.
通过对焊接工艺的概述提出了焊接变形控制措施研究的意义和目的,在此基础上从材料、结构和工艺3个方面对焊接变形的影响因素作了阐述和分析,然后从焊接变形的因素出发对焊接变形提出了相应的控制措施,并阐述了方法的适用范围和局限点。 相似文献
4.
介绍了履带式液压挖掘机斗杆的结构,对焊接过程中产生的变形进行了分析,通过焊接机器人焊接主要焊缝,采用多层多道焊接、焊后烤火矫正和反变形法对焊接变形进行控制,得到了理想的焊接质量,为客户生产优质产品提供了保障。 相似文献
5.
《新技术新工艺》2016,(1)
分析了后装压缩车侧板上焊接导轨面板变形的原因,建立了薄板焊接失稳变形的数学模型。通过薄板焊接变形失稳原理,降低了相关系数,减少了发热量。采用了合理的焊接方法,改进了焊接工艺,优化了后装压缩车侧板面板焊接时的焊接参数、焊接条件。采用了2∶8配比混合保护气体,改用小直径焊丝,降低电压、电流,提高焊接速度以及合理分布焊缝位置的焊接方案,采用了合理的反变形措施和正确的残余应力释放方法,有效地减小了车厢侧面板的焊接变形量,得出了几种影响薄板焊接的工艺条件。对SPA-H耐候板焊接工艺优化进行了研究,有效地控制了后装压缩车侧板与导轨焊接时面板外侧的焊接变形,可以进一步为薄板焊接变形的控制提供很好的理论控制方法和依据。 相似文献
6.
介绍了在焊接H梁制作过程中采取预留收缩量、反变形法、刚性固定法以及制定合理的焊接工艺等措施来控制焊接变形,同时介绍挠曲变形、角变形的矫正方法。 相似文献
7.
介绍了在焊接H梁制作过程中采取预留收缩量、反变形法、刚性固定法、制定合理的焊接工艺等措施来控制焊接变形,同时介绍挠曲变形、角变形的矫正方法. 相似文献
8.
9.
为解决某型号航空发动机产品焊接加工难题,进行了Inconel 718高温合金薄壁圆筒零件焊接变形控制工艺研究。通过分析薄壁筒体焊接变形的原因,采取合理的接头设计、焊接工装设计、优化焊接工艺和焊后热处理及热处理防变形工装等措施,产品焊缝质量满足I级要求,焊缝圆度变形控制在0.2 mm以内。最终通过了验证,较好地控制了高温合金薄壁圆筒产品焊接变形,焊缝质量优良,可为相关薄壁圆筒产品焊接提供技术支持。 相似文献
10.
11.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
12.
13.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
14.
15.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
16.
一种涡旋压缩机径向随变机构的设计 总被引:1,自引:0,他引:1
详细介绍了运用随变原理设计的一种新型径向密封机构的结构特点,工作原理及主要参数的确定方法,该机构可补偿由于涡旋体加工精度不高而造成的功率损失,适用于涡旋压缩机的批量生产。 相似文献
17.
本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当,影响了仪表的正常使用,制造厂和用户应关注这类问题。 相似文献
18.
针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。 相似文献
19.
V. P. Dragunov E. G. Kostsov 《Optoelectronics, Instrumentation and Data Processing》2009,45(3):234-242
Specific features of operation of one- and two-capacitor microelectromechanical converters (MEMC) of energy of mechanical microscopic vibrations into electric energy with a modulated electrode-gap magnitude and with allowance for the mutual influence of electrical and elastic forces are analyzed, and the characteristics of these two devices are compared. The main factors restricting the increase in MEMC power are demonstrated to be the effects of “collapsing” and the condition of conservation of positive rigidity of the system. Expressions for estimating the limiting MEMC parameters are derived. The possibility of electrical energy generation in the presence of “real“ sources of wide-spectrum microscopic vibrations is considered. 相似文献