Pulsed Laser Deposition of YBa2Cu3O7 Superconducting Film on MgO Templates Spray Pyrolyzed on Hastelloy C276

Pulsed laser deposition (PLD) was used to deposit YBCO on MgO-buffered C276 substrates in order to evaluate the quality of the deposited MgO films which were deposited by spray pyrolysis. The characterization of the thin films was done using scanning electron microscopy, atomic force microscopy, electron backscattered diffraction, X-ray diffraction 2??-scans, rocking curve (??-scans), phi scan, pole-figure measurements, and AC susceptibility. It was found that c-axis oriented YBCO films were grown on c-axis oriented MgO films which confirm that the deposited YBCO films copied the out-of-plane texture of the spray pyrolyzed MgO buffer. However, MgO and YBCO films have a very weak in-plane texture. The AC susceptibility measurements show that the YBCO films have a broad superconducting transition temperature which may be attributed to the weak in-plane texture.     

Fabrication of low cost YBCO coated conductors using Ag-clad Hastelloy substrates

Mechanically reinforced Ag-clad Hastelloy tapes were fabricated as the inexpensive substrates for coated conductors without any buffer layer. The clad substrate has good adhesion between Ag and Hastelloy layers. Superconducting YBa₂Cu₃O₇ (YBCO) films were directly deposited on Ag-clad Hastelloy substrates by chemical vapor deposition in high magnetic fields. YBCO films were highly oriented along the c-axis perpendicular to the substrate with a zero resistance transition temperature of 86.2 K and a transport J_c value of 10⁴ A/cm² at 77 K and zero magnetic field. These results indicate that the present work appears to be a promising way for the development of YBCO films for large-scale applications.     

Tailoring in-plane crystallographic orientation of epitaxial YBa2Cu3O7 − x thin films having perpendicular c-axis texture

Control of the in-plane crystallographic orientation of YBa₂Cu₃O_7 − x (YBCO) films on (100) MgO substrates is of significant application value due to the selective enhancement of superconducting properties. In the present work, the preparation, crystallographic and superconducting properties of YBCO films deposited on MgO substrates are reported. Crystallographic in-plane orientation was realized by means of tailoring the pulsed laser deposition conditions and the use of interfacial buffering structures. Superconductiong properties were measured for films having different in-plane orienations. The results indicate that the 0^° in-plane oriented films showed the highest current density of 1.62 MA/cm² that was attributed to the elimination of high-angle grain boudaries. Additionally, the growth mechanism of YBCO films was discussed in terms of crystallographic and thermodynamic theory.     

Growth and Characterization of PrBa2Cu3O7−<Emphasis Type="Italic">x</Emphasis> Thin Film Used as Template Layer on SrTiO3 Substrate

We have grown PrBa₂Cu³O_7?x (PBCO) thin films on (100) SrTiO₃ substrates using pulsed laser deposition (PLD). X-ray diffraction (XRD) studies indicate that the orientation of PBCO films varied with increasing deposition temperature: b axis oriented films can be grown at 680°C, and a axis oriented films at the temperature between 692°C and 705°C. Atomic force microscopy (AFM) reveals that a good flatness of the films was obtained with surface mean roughness of less than 24 Å, indicating that it is suitable for use as template layers in a axis oriented epitaxial YBa₂Cu₃O_7?y/PBCO and YBCO/tetragonal–YBCO/PBCO multilayer structures.     

Microstructure and electrical properties of YBCO thin films

Microstructures of c-axis oriented YBCO thin films made by high-pressure d.c. sputtering on LaAlO₃ and MgO substrates were examined by TEM. The a-axis oriented grains, second phases and micro-twins were frequently observed in the film. The a-axis oriented grains expanded along their c-axis directions during film growth. The a- and b-axis misorientations were observed in the film on MgO due to serious lattice mis-match between YBCO and MgO. The second phases were often accompanied with a-axis oriented grains suggesting they act as nuclei. These observed results were correlated with the measured T _c and J _c of the films.     

The Influence of the Microstructure and Morphology of CeO 2 Buffer Layer on the Properties of YBCO Films PLD Grown on Ni Tape

YBa₂Cu₃O_7?δ films were deposited on CeO₂-buffered nickel substrates, with different buffer thickness. Full width at half maximum of rocking curve, Δω, of CeO₂ and yttrium barium copper oxide (YBCO), as well as the critical temperature, T _c, of YBCO were shown to be strongly dependent on buffer thickness. They behave similarly but not proportional to the buffer thickness increase. This and the fact that Δω vs. buffer thickness and T _c vs. buffer thickness for YBCO behave similar with RMS roughness vs. thickness of CeO₂ indicates that the surface peculiarity of buffers is responsible for YBCO properties. More precisely, the surface of CeO₂ films prepared by the chemical solution route based on propionic acid is prone to agglomerate (de-wet) and the degree of agglomeration depends in an intricate way on buffer thickness. We showed that nor RMS roughness neither (00 l) texture degree can define alone the surface suitable for c-axis YBCO nucleation. The {111} faceted grains (even in the case of high (00 l) texture) and other defects generated by agglomeration supply a low fraction of (00 l) flat terminations of buffer that affect the nucleation of c-axis-oriented YBCO phase. Moreover, the thermal instability of the surface morphology of CeO₂ buffers (further development of de-wetting process, {111} faceted grains, etc. during superconducting layer deposition) influence the quality of YBCO films.     

Studies of solution deposited cerium oxide thin films on textured Ni-alloy substrates for YBCO superconductor

Cerium oxide (CeO₂) buffer layers play an important role for the development of YBa₂Cu₃O_7−x (YBCO) based superconducting tapes using the rolling assisted biaxially textured substrates (RABiTS) approach. The chemical solution deposition (CSD) approach has been used to grow epitaxial CeO₂ films on textured Ni–3 at.% W alloy substrates with various starting precursors of ceria. Precursors such as cerium acetate, cerium acetylacetonate, cerium 2-ethylhexanoate, cerium nitrate, and cerium trifluoroacetate were prepared in suitable solvents. The optimum growth conditions for these cerium precursors were Ar–4% H₂ gas processing atmosphere, solution concentration levels of 0.2–0.5 M, a dwell time of 15 min, and a process temperature range of 1050–1150 °C. X-ray diffraction, AFM, SEM, and optical microscopy were used to characterize the CeO₂ films. Highly textured CeO₂ layers were obtained on Ni–W substrates with both cerium acetate and cerium acetylacetonate as starting precursors. YBCO films with a J_c of 1.5 MA/cm² were obtained on cerium acetylacetonate-based CeO₂ films with sputtered YSZ and CeO₂ cap layers.     

Growth and Characterization of PrBa2Cu3O7?x Thin Film Used as Template Layer on SrTiO3 Substrate

We have grown PrBa₂Cu³O_7–x (PBCO) thin films on (100) SrTiO₃ substrates using pulsed laser deposition (PLD). X-ray diffraction (XRD) studies indicate that the orientation of PBCO films varied with increasing deposition temperature: b axis oriented films can be grown at 680°C, and a axis oriented films at the temperature between 692°C and 705°C. Atomic force microscopy (AFM) reveals that a good flatness of the films was obtained with surface mean roughness of less than 24 Å, indicating that it is suitable for use as template layers in a axis oriented epitaxial YBa₂Cu₃O_7–y /PBCO and YBCO/tetragonal–YBCO/PBCO multilayer structures.     

High-temperature superconducting dual-mode resonator on (100) MgO substrate

We report, for the first time to our knowledge, a clear resonant peak split in the range of 7.7–9.7 GHz in a perturbed dual-mode disk-type resonator (DMDR) made of YBa₂Cu₃O_7–x (YBCO) superconducting thin film on MgO substrate. Epitaxial YBCO superconducting thin films were grown on (100) MgO substrates by pulsed laser deposition technique. The critical temperature of superconducting thin film on MgO substrate was 85 K. Superconducting dualmode disk resonators were designed by microwave design software, EEsof, and patterned by photolithography and a wet-etch process. The unloaded quality factor (Q_UL) of the superconducting DMDR was found to be 1,312 at 77 K. We believe this type of DMDR can be utilized for dual-mode resonator-based filters for satellite communications.     

Pure and fully texturized Sr2FeMoO6 thin films prepared by pulsed laser deposition from target made with citrate-gel method

Sr₂FeMoO₆ (SFMO) thin films were grown on SrTiO₃ and MgO single crystal substrates by pulsed laser deposition. The SFMO target with nanometer sized grains for the film preparation was made from powder prepared by citrate-gel method. The parameters for ablation were optimized and the importance of the substrate temperature is observed. Film quality was verified with various X-ray diffraction methods and magnetometric measurements. The films are pure, without impurities such as metallic iron, Fe₂O₃, SrMoO₃ or SrMoO₄ and they are completely c-axis oriented. The Curie temperature for the films is higher than room temperature.     

Fabrication of biaxially textured magnesium oxide thin films by ion-beam-assisted deposition

Biaxially textured MgO thin films were grown by ion-beam-assisted deposition. The film growth parameters of film thickness, ion-to-atom arrival ratio (r-value), ion beam angle, and ion beam voltage were studied. Film characterization was performed by X-ray diffraction, pole figure analysis, and atomic force microscopy (AFM). Full-width half-maximum (FWHM) of MgO (220) ?-scans and MgO (002) ω-scans, respectively, were used to evaluate in-plane and out-of-plane film texture. MgO (220) ?-scan FWHM of 3.2° and MgO (002) ω-scan FWHM of 1.2° was achieved on amorphous Si₃N₄-coated Si substrates using a 1500-V ion source oriented at 45° to the substrate normal and an r-value of 0.90. Depositions on metallic substrates yielded MgO (220) ?-scan FWHM values of 5.2° and MgO (002) ω-scan FWHM of 2.5°. Root-mean-square surface roughness of these films as measured by AFM was ≈2.3 nm.     

Influence of Deposition Pressure (O2) on the YBCO (Y123) Thin Films Prepared by Pulsed Laser Deposition

In this paper, the influence of oxygen pressure on film quality and superconducting properties of YBa₂Cu₃O_7?δ (YBCO-Y123) thin films prepared by Pulsed Laser Deposition (PLD) was investigated. For this purpose, YBCO thin films were deposited on polished LaAlO₃ (l00) (LAO) substrates at three different oxygen pressures (150, 200, and 250 mTorr). X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) techniques were used to make comparative studies of film microstructure. Except for oxygen pressures, all other variables such as number of pulses, repetition rate, deposition temperature, heating and cooling rate, target-substrate distance, laser excitation energy, annealing temperature, and annealing pressure were fixed. For this fixed set of parameters, SEM, XRD analysis, and AC susceptibility measurements of these films revealed that the crystal structure quality and superconducting properties of YBCO thin films are optimum at the oxygen deposition pressure of 150 mTorr. As the deposition pressure increased, Y₂BaCuO₅ (Y211) phase peaks were seen in XRD patterns. The reason for this was believed to be caused by decreased concentration of CuO and BaO as determined by Energy Dispersive X-Ray Spectroscopy (EDX) of thin films.     

Crystal Structure and Superconductivity of MgB2 Thin Films Grown on Various Oxide Substrates

The crystal structure and superconductivity of MgB₂ thin films grown on various oxide substrates were investigated by X-ray diffraction and resistance measurement. The films were prepared by a two-step method, in which precursors B films were annealed in Mg vapor at 900^○C. The X-ray diffraction shows that the MgB₂ films grown on C–AL₂O₃, R–AL₂O₃, and MgO (001) are c-axis oriented while the films grown on SrTiO₃ (001), LaAlO₃ (001), and ZrO₂ (001) are aligned with the (101) direction normal to the substrate planes. All the grown films show superconductivity and their transition temperature varies with the substrates in the range of 34–39 K. We think that the transition temperature variation is probably due to the lattice matching between the film and the substrate, as well as the interdiffusion at the film/substrate interface. The experimental results suggest that if there is no severe interdiffusion at the film/substrate interface in the high temperature annealing process, more substrates could be used for the growth of MgB₂ films using the two-step method.     

Enhanced Flux Pinning Properties of BaZrO3-doped YBCO Films Grown by Pulsed Laser Deposition on LaAlO3(100) Substrates Decorated with Y2O3 Nanoislands

In this work, we intend to investigate the interaction between two types of nanoscaled artificial pinning centers and their pinning properties in YBCO thin films grown by pulsed laser deposition technique. The two types of artificial pinning centers were prepared in different processes, (1) Y₂O₃ nanoislands decorated on substrates prior to the deposition of YBCO thin film, and (2) BaZrO₃ nanoparticles self-assembled within YBCO matrix during the deposition of YBCO thin film. We compared the transport characteristics of the YBCO thin films containing these two types of artificial pinning centers with those of pure YBCO thin films grown on decorated substrates and BZO-doped YBCO thin films grown on undecorated substrates. It was found that these two types of artificial pinning centers, which are simultaneously present, acted constructively to enhance the pinning properties of YBCO thin films.     

Effect of PbO<Subscript>2</Subscript> on the Formation of YBCO Films Fabricated Via Sedimentation Deposition and Partial Melting Technique

PbO₂ addition in sedimentation deposition prepared films was investigated by SEM, EDX, and RT measurements to determine its effect on the formation of YBCO films. YBCO films on SrTiO₃ (STO) (100) substrates of varying amounts of PbO₂ were partially melted at 980 ^°C, annealed, and oxygenated in flowing oxygen atmosphere. In addition, a YBCO sample partially melted at higher temperature was also done for comparison. From the SEM, EDX, and RT analyses, it was found that the film having 8 wt% PbO₂ produces a film with the highest superconducting transition temperature comparable to that of a YBCO sample partially melted at peritectic point. Moreover, it was observed that addition of PbO₂ enhances matter transport between Y123 particles and lowers the processing temperature for the fabrication of YBCO films via the sedimentation deposition method.     

Processing of Y1Ba2Cu3O x Films by Solution Techniques Using Metal-Organic Decomposition

Processing of YBCO films by decomposition of metal trifluoroacetate precursors and its application to the development of coated conductors is investigated. The technique involves preparation of the solution, deposition, and a two-stage heat treatment. A stoichiometric mixture of the acetates of Y, Ba, and Cu and trifluoroacetic acid are used as the starting materials. The glassy residue of the trifluoroacetates of Y, Ba, and Cu formed by drying the above mixture is redispersed in a fixed amount of methanol to provide the starting solution of a given concentration. This solution is then deposited on the substrate surface by the spin coating technique and heat treated in two stages. X-Ray characterization shows that the transformation to 123 is complete in less than 1 h. Pole figure analysis of films deposited on (100) SrTiO₃ and LaAlO₃ single crystal substrates show that these films have a very high degreee of alignment with the substrate both out-of-plane (<0.5°) and in-plane (<1.5°). These chemically derived films were also found to have critical current densities well above 5 × 10⁵ at 77 K for 0.5 μm thick films. The applicability of this technique to the production of thick films of YBCO for the development of coated conductors will be discussed.     

Processing of Y1Ba2Cu3Ox Films by Solution Techniques Using Metal-Organic Decomposition

Processing of YBCO films by decomposition of metal trifluoroacetate precursors and its application to the development of coated conductors is investigated. The technique involves preparation of the solution, deposition, and a two-stage heat treatment. A stoichiometric mixture of the acetates of Y, Ba, and Cu and trifluoroacetic acid are used as the starting materials. The glassy residue of the trifluoroacetates of Y, Ba, and Cu formed by drying the above mixture is redispersed in a fixed amount of methanol to provide the starting solution of a given concentration. This solution is then deposited on the substrate surface by the spin coating technique and heat treated in two stages. X-Ray characterization shows that the transformation to 123 is complete in less than 1 h. Pole figure analysis of films deposited on (100) SrTiO₃ and LaAlO₃ single crystal substrates show that these films have a very high degreee of alignment with the substrate both out-of-plane (<0.5°) and in-plane (<1.5°). These chemically derived films were also found to have critical current densities well above 5 × 10⁵ at 77 K for 0.5 m thick films. The applicability of this technique to the production of thick films of YBCO for the development of coated conductors will be discussed.     

Low cost synthesis of high-Tc superconducting films on metallic substrates via ultrasonic spray pyrolysis

Ultrasonic spray pyrolysis technique has been used to deposit both in situ and ex situ high temperature superconducting films (HTSC) of Y₁Ba₂Cu₃O_x(YBCO) and Bi₂Sr₂CaCu₂O_x (BSCCO) compounds over various substrates. Nitrate precursor solutions are used to deposit films of ∼10 μm thickness. Both low temperature spray with substrate temperature T_s < 500 °C and high temperature deposition with T_s = 550-900 °C are carried out. Superconducting properties of these films are observed to vary with various parameters such as concentration of spray solution, deposition temperature and nature of substrate and annealing process. Best quality films show T_c (R = 0) of 89 K and J_c of ∼4 × 10⁴ A/cm² at 77 K and ∼ 10⁵ A/cm² at 20 K. X-ray diffraction pattern reveals that the films are textured along c-axis. Successful attempt has been made to deposit in situ superconducting films over polycrystalline Ag for coated conductor applications. Various deposition and annealing conditions are optimized to control the diffusion of Ag from substrate to film, which otherwise can segregate into the grain boundaries and make the films non-superconducting.     

MOCVD-grown homoepitaxial YBa2Cu3Ox thin films and its multilayers

YBa₂Cu₃O _x (YBCO) films, Zn-doped YBCO (YBCO : Zn) films, and their bilayers have been epitaxially grown on SrTiO₃(100) and single-crystal YBCO(001) substrates by metalorganic chemical vapour deposition. The YBCO(001) films homoepitaxially grown on YBCO(001) substrates have flat surfaces on an atomic scale, and interfaces free from crystalline defects. We can systematically reduce the superconducting transition temperature (T _c) of YBCO : Zn films from 90 K to 37 K by increasing Zn concentration. The bilayers have a sharp distribution of Zn as evaluated fromT _c measurements of the upper YBCO films and depth profiles of secondary ion mass spectrometer, suggesting the possibility to form the homoepitaxial SNS (S, superconductor; N, normal metal) junction operatable between 40 K and 90 K.     

UV-enhanced atomic layer deposition of ZrO2 thin films at room temperature

A UV-enhanced atomic layer deposition (UV-ALD) process was developed to deposit ZrO₂ thin films on poly(ethylene terephthalate) (PET) polymer substrates using zirconium tetra-tert-butoxide (ZTB) and H₂O as precursors with UV light. In the UV-ALD process, the surface reactions were found to be self-limiting and complementary enough to yield uniform, conformal, and pure ZrO₂ thin films on polymer substrates at room temperature. The UV light was very effective to obtain the high-quality ZrO₂ thin films with good adhesive strength on polymer substrates. The ZrO₂ thin films exhibit large-scale uniformity, sharp interfaces, and unique electrical properties.