共查询到17条相似文献,搜索用时 125 毫秒
1.
针对用高锌镉生产精镉工艺中存在的修炉停产时间长、加工费用高等问题,在化学法除锌时添加硝酸钠,可将高锌镉中的锌除至0.001%,不用精馏就可以生产精镉。 相似文献
2.
3.
段毅 《有色冶金设计与研究》2020,(2):14-17
针对小型电锌生产企业生产状况,对电锌系统产出的锌镉渣进行试验研究,采用全湿法处理工艺回收其中的锌和镉。试验对浸出酸度、液固比、反应时间对镉浸出率的影响进行了研究,确定了最佳浸出条件。在最佳浸出条件下,研究了锌粉用量对镉置换率的影响,并对镉的电积条件与熔铸过程进行了分析。经过研究,可以得到含镉达99.97%的精镉产品,锌直收率>90%,镉直收率>88%。 相似文献
4.
5.
建立一种用酸分解试样定容后,连续测定锌、镉含量的方法。第一步返滴定,在pH5.6~5.8的乙酸-六次甲基四胺缓冲溶液中,用过量Na2EDTA标准溶液络合锌、镉,以二甲酚橙为指示剂,用锌标准溶液返滴定,测得结果为锌镉合量。第二步置换滴定,以过量Na2EDTA标准溶液络合锌、镉,再加入碘化钾络合镉,置换释放出与镉络合的Na2EDTA,在pH5.6~5.8的乙酸-六次甲基四胺缓冲溶液中,以二甲酚橙为指示剂,用锌标准溶液返滴定,测得结果为锌量。以锌镉合量减去锌量即为镉量。方法对镉渣中锌、镉的测定值相对标准偏差0.1%~1.0%,加标回收率在98%~101%之间。 相似文献
6.
7.
对镉在烧结、熔炼、精馏过程中的行为进行分析,结合生产实践总结出精矿含镉与粗锌含镉、精锌品级率的关系,从技术经济角度论证了镉对精馏过程指标、效益的影响。 相似文献
8.
随着锌用途的扩大,低镉低铁锌出现市场需求。生产中,粗锌通过铅塔、镉塔的精馏精炼得到精锌产品。对铅塔、镉塔进行局部技术改造达到降低成品锌中镉、铁含量的目的,从而满足市场需求。 相似文献
9.
对从锌精矿焙烧电尘中回收镉的工艺进行了研究,比较了水浸、酸浸及氧化酸浸3种浸镉方法,指出氧化酸浸-除砷-置换-压团-熔铸是回收镉的最佳流程,用这种方法处理含镉电尘,镉的浸出率大于90%,粗镉品位99.10%。 相似文献
10.
进行了含镉物料单塔处理一步产出粗镉的工业试验。采用1372大型铅塔处理含镉40%-90%的物料可使镉富集到98%左右。铅、锌度其它高沸点杂质金属的含量符合粗镉要求。 相似文献
11.
The hypothesis that in tumor-bearing animals an increase of host hepatic zinc metallothionein (Zn-MT) causes a restriction of zinc in the tumor tissue was studied. Three types of tumors were induced in laboratory mice by cell transplant. Tumor growth appears to be inhibited under zinc-deficient conditions, even in cases where zinc deficiency was started after tumor cell transplant. The survival times of tumor-bearing mice were prolonged by administration of cadmium chloride, which induces the synthesis of a combined zinc-cadmium metallothionein derivative in the host liver, but not in the tumor tissue, leading to an increase of hepatic zinc in the treated animals. The uptake of 65Zn by the liver of Cd-treated, tumor bearing mice was significantly higher than that of controls whereas uptake of 65Zn by tumor cells was significantly higher in controls than in the treated animals. These results suggest that restriction of zinc intake suppresses tumor growth. 相似文献
12.
L. V. Volkov S. P. Shkuryakova Nguen Ba Khal 《Powder Metallurgy and Metal Ceramics》1985,24(8):589-592
Conclusions Electrolytic deposition of cadmium-zinc alloy powders from sulfate solutions is possible provided that the reduction of cadmium ions is performed under limiting diffusion current conditions. Simultaneous discharge of cadmium and zinc ions is not accompanied by super- and depolarization phenomena, which enables the alloy composition to be predicted using polarization curves of reduction of the two kinds of ion in individual solutions. Because of growth of the alloy deposit surface during galvanostatic deposition, the composition of the powder is a function of buildup time, and can be changed only by varying the solution composition. Consequently, it is best to produce such powders either under potentiostatic conditions or under galvanostatic conditions but with continual removal of deposited powder from the basis.Translated from Poroshkovaya Metallurgiya, No. 8 (272), pp. 6–10, August, 1985. 相似文献
13.
在热镀锌铝镁合金镀层产品中,镀层中铅、镉含量是评价产品质量的重要指标,目前无相关标准方法对锌铝镁镀层中铅、镉含量进行检测。实验建立了采用火焰原子吸收光谱法(FAAS)测定热镀锌铝镁合金镀层中铅、镉含量的方法。采用30%(V/V)盐酸溶解合金镀层,同时加入六次甲基四胺作为缓蚀剂保护镀层基体,合金镀层可以被完全溶解且不会腐蚀基体。在优化的仪器工作条件下,采用基体匹配法消除镀层基体元素锌对待测元素的基体效应影响,在波长217.0nm和228.8nm处使用原子吸收光谱法测定铅和镉。铅和镉校准曲线的线性相关系数均大于0.9995;方法的检出限分别为0.0020mg/L和0.0010mg/L。按照实验方法测定热镀锌铝镁合金镀层中铅、镉,结果的相对标准偏差(RSD,n=10)为2.4%~6.3%;加标回收率为97%~103%。 相似文献
14.
建立了测定锌合金中铝、铅、铁、镉、铜、锡6种元素的直读光谱分析方法。通过试验,确定了各项分析条件的选择,结果表明:该方法的准确度、精密度符合分析要求。 相似文献
15.
锌精矿中锌的快速测定 总被引:1,自引:0,他引:1
建立了锌精矿中锌测定的新方法。对共存离子的影响、掩蔽剂的选择、掩蔽剂的用量以及锌标准加镉同收实验、样品加标回收实验进行了探讨。结果表明,在pH5—6的溶液中选择碘化钾为掩蔽剂,碘化钾的用量大于5g镉才能掩蔽完全,锌标准加镉回收实验当镉量小于5mg时锌回收率达99.9%~100.9%,样品加标回收实验锌同收率在98%以上。该方法适用于锌精矿及含镉锌矿中锌的测定,结果与借助极谱仪测定的结果相一致。 相似文献
16.
Pb-Ag-Ca-Sr四元合金具有较好的力学性能、导电性能和耐腐蚀性能,但合金元素分布不均、性能不稳定、稀贵金属损耗大、制作成本高,制约其在湿法炼锌电积阳极的广泛应用。通过熔炼工艺向Pb-Ag-Ca-Sr四元合金中添加稀土Ce,然后进行轧制,分别考察稀土Ce对Pb-Ag-Ca-Sr四元合金显微组织、力学性能、导电性和耐腐蚀性能的影响。结果表明,添加质量分数为0.04%的稀土Ce后,Pb-Ag-Ca-Sr四元合金的晶粒明显得到细化,抗拉强度、屈服强度和电导率分别提高9%、23%和1.75%,耐腐蚀性能也得到明显提高,稀土Ce对Pb-Ag-Ca-Sr四元合金阳极材料综合性能提升作用强于轧制工艺。 相似文献