γ ? α2 Phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%)

The ₂ phase transformation in fractured high temperature stress rupture Ti-48Al-2Nb(at.%) alloy has been studied by analytical electron microscopy. ₂ and phases were found at grain boundaries. ₂ layers that suspended in layers and interfacial ledge higher than 2d ₍₁₁₁₎ at /₂ interfaces were observed in the lamellar grains. These facts indicated that ₂ phase transformation and dynamic recrystallization have occurred during high temperature stress rupture deformation. It can be concluded that deformation induced ₂ phase transformation and dynamic recrystallization resulted in the presence of particles at grain boundaries. A structural and compositional transition area between deformation-induced ₂(or ) and its adjacently original (or ₂) phases was found by HREM and EDS and is suggested as a way to transform between and ₂ phase during high temperature stress rupture deformation. The transition area was formed by slide of partial dislocations on close-packed planes and diffusion of atoms.     

The role of starting powder size on the compressive response of stand-alone plasma-sprayed alumina coatings

Cylindrical stand-alone tubes of plasma-sprayed alumina were tested in uniaxial compression at room temperature, using strain gages to monitor axial strains. The effect of lamella size on the mechanical response was investigated by employing different starting powders to fabricate samples. The average powder sizes investigated included 9 m, 19 m and 32 m alumina; the resulting effective lamella diameters were 10 m, 28 m, and 55 m, respectively. Similar stress-strain hysteresis was observed on unloading in all tubes, independent of lamella size. A strong correlation between the failure stress and the cumulative strain at failure was also observed for tubes fabricated from the three powders. For samples with approximately constant densities, tubes plasma sprayed with the 9 m powder exhibited greater moduli than tubes sprayed from either 19 or 32 m powders. This difference was attributed to the greater percentage of unmelted -Al₂O₃ in the coating.     

Theory of RF SQUIDs Operating in the Presence of Large Thermal Fluctuations

A comprehensive analytical theory is presented for non-hysteretic RF SQUIDs operating in the adiabatic mode in the presence of large thermal fluctuations. When 1 ( = 2LI_c/₀ is the hysteresis parameter, L is the SQUID inductance, I_c is the critical current of the Josephson junction, and ₀ is the flux quantum) the theory is applicable also for RF SQUIDs operating in the non-adiabatic mode. In contrast to previous theories in which the noise is treated perturbatively and which therefore are applicable only if the product 1 ( = 2k_BT/ ₀ I_c is the noise parameter, k_B is the Boltzmann constant, and T is the absolute temperature)—the case of small thermal fluctuations—the present theory is valid for around unity or higher. In the limit 0 the theory reproduces the results of small thermal fluctuations theories. It has been found that in the presence of large thermal fluctuations the screening current in the SQUID inductance is suppressed by a factor that increases with increasing . Taking into account this new basic fact, all SQUID characteristics (output signal, transfer function, noise spectral density and energy sensitivity) have been recalculated and a good agreement with experimental data has been obtained. It has been also found that RF SQUIDs can be operated with substantially higher values of the inductance and of the noise parameter than DC SQUIDs. These two aspects, which are of particular importance at liquid nitrogen temperature, make high T_c RF SQUIDs very attractive.     

Single-Mode As–S Glass Fibers

Single-mode As–S glass fibers with a core diameter from 3 to 20 m and a clad diameter of 125 m are prepared by the double-crucible method. The cutoff wavelength of the fibers is 0.9–6 m. The lowest transmission losses in the fibers at 2.2–2.3 m are 100 dB/km, and their mean bending strength is 800–1000 MPa.     

A note on the similarity solutions for free convection on a vertical plate

Summary The similarity solutions for free convection on a vertical plate when the (non-dimensional) plate temperature is x and when the (non-dimensional) surface heat flux is –x are considered. Solutions valid for 1 and 1 are obtained. Further, for the first problem it is shown that there is a value ₀, dependent on the Prandtl number, such that solutions of the similarity equations are possible only for >₀, and for the second problem that solutions are possible only for >–1 (for all Prandtl numbers). In both cases the solutions becomes singular as ₀ and as –1, and the natures of these singularities are discussed.     

Flow visualization glass-ceramic: Preliminary experimental and modelling results

A glass-ceramic material was developed to act as a flow visualization material. Preliminary experiments indicate that aperiodic, thermally induced, convective flows can be sustained at normal processing conditions. These flows and the stress and temperature gradients induced are most likely responsible for the anomalous behaviour seen in these materials and the difficulties encountered in their development and in their production on industrial and experimental scales. A simple model describing the dynamics of variable-viscosity fluids was developed and was shown to be in qualitative agreement with more sophisticated models as well as with experimental results. The model was shown to simulate the dependence of the critical Rayleigh number for the onset of convection on the viscous properties of the fluid at low T, and also to simulate quenching behaviour when the temperature differences were high.Nomenclature C _p Heat capacity - D, E, F Expansion coefficients - H Height of the roll cell - Pr Prandtl number - R _a Rayleigh number - R _c Critical Rayleigh number for the onset of convection in a constant-viscosity fluid - S Dimensionless stream function - T Temperature - T _m Mean temperature - T ₀ Bottom surface temperature - T _r Reference temperature - a Aspect ratio of cell - g Acceleration due to gravity - k Thermal conductivity - k ₁ Function related to ²v/T ² - k ₂ Function related to ⁴v/T ⁴ - r Rayleigh number ratioR _a/R _c - t Time - w Dimensionless vertical coordinate - w _m Mean cell height - x Horizontal coordinate - y Dimensionless horizontal coordinate - z Vertical coordinate - , Constants - _t Thermal expansion coefficient - Constant in viscosity function - T Temperature difference between top and bottom surfaces - _i Viscosity coefficients - Kinematic viscosity - _m Mean kinematic viscosity - Dimensionless kinematic viscosity - Thermal diffusivity - Non-linear temperature function - Dimensionless non-linear temperature function - _o - Stream function - Dimensionless time - Eigenvalues     

Theory of periodically driven,current-carrying,superconducting filaments. I. Spatially homogeneous states

Starting from the nonequilibrium theory of dirty superconductors in the Ginzburg-Landau regime, spatially homogeneous states with an applied currentI=I ₀+I ₁ cos (t) are considered. Expressions for the linear response (I₁ small) valid up to high frequencies (k _BT_c) are derived and evaluated analytically for the experimentally important case of smallI ₀ and ₀(T). Then the nonlinear response is treated for frequencies with _E1. Interesting new behavior is found for frequencies ₀ 1, where ₀ is essentially the GL relaxation time.     

Nonlinear asymptotic theory of hypersonic flow past a circular cone

Summary The hypersonic small-disturbance theory is reexamined in this study. A systematic and rigorous approach is proposed to obtain the nonlinear asymptotic equation from the Taylor-Maccoll equation for hypersonic flow past a circular cone. Using this approach, consideration is made of a general asymptotic expansion of the unified supersonic-hypersonic similarity parameter together with the stretched coordinate. Moreover, the successive approximate solutions of the nonlinear hypersonic smalldisturbance equation are solved by iteration. Both of these approximations provide a closed-form solution, which is suitable for the analysis of various related flow problems. Besides the velocity components, the shock location and other thermodynamic properties are presented. Comparisons are also made of the zeroth-order with first-order approximations for shock location and pressure coefficient on the cone surface, respectively. The latter (including the nonlinear effects) demonstrates better correlation with exact solution than the zeroth-order approximation. This approach offers further insight into the fundamental features of hypersonic small-disturbance theory.Notation a speed of sound - H unified supersonic-hypersonic similarity parameter, - K hypersonic similarity parameter, M - M freestream Mach number - P pressure - T temperature - S entropy - u, v radial, polar velocities - V freestream velocity - shock angle - cone angle - density - density ratio, /() - ratio of specific heats - polar angle - stretched polar angle, / - (), (), () gage functions     

Microstructure and mechanical properties of rapidly quenched L20 and L20+L12 alloys in Ni-Al-Fe and Ni-Al-Co systems

Ductile L2₀-type wires and+L1₂-type duplex wires with high strengths and large elongation in the Ni-Al-Fe and Ni-Al-Co ternary systems have been manufactured directly from the liquid state by an in-rotating-water spinning method. The wire diameter was in the range 80 to 180m and the average grain size was 2 to 4m for the wires and 0.2 to 1.0m for the+ wires. _y, _f and _p of the wires were found to be about 360 to 760 MPa, 560 to 960 MPa, and 0.2 to 5.5%, respectively, for the Ni-Al-Fe system, those of the+ wires were about 395 to 660 MPa, 670 to 1285 MPa, and 3.5 to 17%, respectively, for the Ni-Al-Fe system, and about 260 to 365 MPa, 600 to 870 MPa, and 4.0 to 7.0%, respectively, for the Ni-Al-Co system. Cold-drawing caused a significant increase in _y and _f and the values attained were about 1850 and 2500 MPa, respectively, for Ni-20Al-30Fe and Ni-25Al-30Co wires drawn to about 90% reduction in area. The high strengths, large elongation and good cold-workability of the melt-quenched and+ compound wires have been inferred to be due to the structural change into a low-degree ordered state containing a high density of phase boundaries, suppression of grain-boundary segregation and refinement of grain size.     

Determination of the local angular radiation coefficients in certain two-body systems

A method is shown and formulas are derived by which local angular radiation coefficients can be determined in certain two-body systems where the configuration is arbitrary but one of the bodies is either a cylinder or a rectangular plate.Notation _int radiation vector of body 1 - _E ^int intrinsic radiation intensity of body 1 - _x, _y, _z components of the geometrical radiation vector along rectangular coordinates - r₀=x²+z² shortest distance from point M(x, y, z) to linear radiator - ₀ , ₀ ^' angles subtending the two segments of the linear radiator from point M(x, y, z) on area element 2 of irradiated surface - l length of the cylinders - x, y, z space coordinates of point M Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 22, No. 6, pp. 1080–1088, June, 1972.     

Transport results from untwinned YBCO: Washboard frequency of the vortex lattice,and the quasiparticle mean free path

The washboard frequency of the moving vortex lattice in untwinned YBa₂ Cu₃ O_6.93 may be observed through mode-locking to an externally applied ac current of frequency _ext. The interference between and _ext results in jumps in the dc current-voltage characteristics when and _ext are harmonically related¹. The interference effect disappears in the vortex liquid state. The Hall conductivity _xy below T_c in YBCO contains contributions² from a positive quasiparticle (qp) term (H) and a negative vortex term (1/H). The qp term is surprisingly large well below T_c and implies a large gap anisotropy and a long qp mean free path (mfp). The thermal Hall effect³ _xy is closely related to the qp _xy; _xy is produced by asymmetric scattering of qp by pinned vortices. The qp mfp at H = 0, extracted from _xy and extended to low T by _xy, increases remarkably from 90 Å at T_c to more than 0.5m at 22 K.     

Preparation of Si3N4 whiskers by reaction of wheat husks with NH3

-Si₃N₄ whiskers that are 1–10 mm long and 0.5–1.1 m thick were obtained by the reaction of wheat husks with NH₃ at 1250–1450 °C. A maximum whisker yield of about 30% was obtained at 1450 °C with the addition of an iron impurity. Whiskers with 1.3–2.2 m thickness (average 1.6 m) were obtained by the addition of an H₂S impurity. Thin whiskers with periodic thick and thin diameters were also obtained.     

Geometrical factors for parts of an infinite cylindrical surface

A method is described for calculating geometrical factors, allowing for attenuation of radiation by the medium, and computing radiative heat transfer between coaxial strips forming part of a cylinder.Notation mean generalized geometrical factor - local generalized geometrical factor for a closed infinite cylindrical surface - F surface area - l length of ray between elements dF_m - D and H diameter and length of cylinder - k ray attenuation coefficient - equivalent solid angle [1] determined from the condition _mm=1 at =0 for a closed surface - f () indicatrix of the specific radiation intensity (a quantity analogous to the specific luminous intensity [1]) - angle between the normal to an element of surface and the ray linking the surface elements - and angles in a section of the surface - angle between the radius and the chord subtending the projections of dF_mon the section - angle between the radius and the chord subtending the projection of element dF_mon the section and the edge of the surface - acute angle between rayl and the generator of the cylinder - ₀ half subtended angle for the arc of a section of the surface - S₂ and M generalized local geometrical factors in the notation of [2] (s₂ and is shown in Table 2 - M local factor for an infinite cylinder with a semicircular cross section for a point in the middle of the plane part of the surface; a table of values of M is given in [2]) - n number of strips     

Correlation between Superconducting Gap and Pseudogap in High-T c Cuprates

We studied the low-temperature energy gap 2 ₀ on Bi ₂ Sr ₂ CaCu ₂ o ₈₊ (Bi2212) and La _2–x Sr _x CuCO ₄ (La214) systematically over a wide range of doping level p using STS, break junction tunneling spectroscopy, Raman scattering and low-T electronic specific heat data. We have also studied the electronic specific heat of La214 in the normal state at T > T _c , and confirmed that pseudogap behavior appears at around T*, below which the in-plane resistivity and magnetic susceptibility tend to be slightly suppressed. Similar suppression appears in and of Bi2212 below the onset temperature of pseudogap T*. It is pointed out in the present study that 2 ₀ is closely related to T* in both Bi2212 and La214 systems; T* 2 ₀ /4.3k _B . It is also pointed out that 2 ₀ is in almost linear proportion to k _B T _max ( T*), where T _max is the temperature exhibiting a broad peak in –T curves and k _B T _max can be considered to give a measure of the effective antiferromagnetic exchange energy J _eff. The factors in 2 ₀ k _B T _max J _eff are 1 for La214 and 2 for Bi2212, respectively. We also report that in both Bi22l2 and La214 systems T _c roughly scales with p ₀ except in highly doped samples, where T _c 2 ₀ .     

Non fermi liquid ground states in strongly correlated f-electron materials

Experimental efforts to characterize and develop an understanding of non Fermi liquid (NFL) behavior at low temperature in f-electron materials are reviewed for three f-electron systems: M_1–xU_xPd₃ (M = Sc, Y), U_1–xTh_xPd₂Al₃, and UCu_5–xPd_x. The emerging systematics of NFL behavior in f-electron systems, based on the present sample of nearly ten f-electron systems, is updated. Many of the f-electron systems exhibit the following temperature dependences of the electrical resistivity p, specific heat C, and magnetic susceptibility for T T₀, where T_o is a characteristic temperature: P(T) 1 –aT/T ₀, where a < 0 or > 0, C(T)/T (-1/T _o) In (T/bT ₀), and (T) 1 –c(T/T_o)^1/2. In several of the f-electron systems, the characteristic temperature T_o can be identified with the Kondo temperature T_k.     

p-Version hierarchical three dimensional curved shell element for heat conduction

This paper presents a finite element formulation for a three dimensional nine node p-version hierarchical curved shell element for heat conduction where the element temperature approximation can be of arbitrary order p , p , and p in the , and directions. This is accomplished by first, constructing one dimensional hierarchical approximation functions and the corresponding nodal variable operators for each of the three directions , and using Lagrange interpolating polynomials and then taking their products (sometimes also called tensor products). The element approximation functions as well as the nodal variables are hierarchical and therefore the element matrices and the equivalent heat vectors are hierarchical also i.e. the element properties corresponding to polynomial orders p , p , and p are a subset of those corresponding to (p +1), (p +1), and (p +1). The element formulation ensures C ⁰ continuity. The curved shell geometry is constructed in the usual way by taking the coordinates of the nodes lying on the middle surface of the element (=0) and the nodal thickness vectors. The element properties i.e. element matrices and the equivalent heat vectors are derived using weak formulation (or quadratic functional) of the three dimensional F ourier heat conduction equation and the hierarchical element temperature approximation. The element formulation is equally effective for very thin as well as extremely thick shells. Numerical examples are presented to demonstrate the accuracy, efficiency, modeling convenience, faster rate of convergence and over all superiority of the present formulation. The h-approximation results are presented for comparison purposes.     

Thermal Conductivity of the Four-Leg Spin-Ladder System La2Cu2O5 Single Crystal

We have investigated the magnetic susceptibility, , and the thermal conductivity, , in magnetic fields for the four-leg spin-ladder system La₂Cu₂O₅ single crystal. The in a magnetic field parallel to the ladder exhibits a kink at 130 K in correspondence to the magnetic ordering. The along the ladder exhibits a peak at 25 K and a shoulder at 14 K, which are probably related to the thermal conductivity due to magnons, _magnon, and that due to phonons, _phonon, respectively. The perpendicular to the ladder, on the other hand, exhibits only one broad peak related to _phonon. The observed large anisotropy of has been explained based upon the anisotropy of _magnon.     

Simulation of the Process of Water Freezing in a Round Pipe

The problem of freezing of pure water in a round pipe is treated with due regard for convection under asymmetric thermal boundary conditions in the absence of motion along the pipe. The problem is solved numerically using the control volume approach, SIMPLER algorithm, and the enthalpy method. Results are obtained for three Grashof (Gr) and six Biot (Bi) numbers: Gr = 1.55 × 10⁶, Bi = 0.305 (0 < ), Bi = 0.044 ( < 2); Gr = 1.24 × 10⁷, Bi = 0.610 (0 < ), Bi = 0.087 ( < 2); Gr = 9.89 × 10⁷, Bi = 1.220 (0 < ), Bi = 0.174 ( < 2). The correctness of calculation of the problem disregarding free-convection flows is analyzed.     

Microstructure-property studies in friction-stir welded, Thixomolded magnesium alloy AM60

Thixomolded magnesium alloy AM60 plates joined by friction-stir welding were observed to be as strong or stronger than the unwelded base material. The thixotropic microstructures of the as-molded plates consisted of either 3% or 18% primary solid fraction of -Mg globules (45 m average size) in a eutectic mixture consisting of -Mg grains (10 m) surrounded by Mg₁₇Al₁₂ intermetallic grains in the -Mg grain boundaries (having an average size of 1–2 m). This complex, composite microstructure became a homogeneous (Mg + 6% Al)), recrystallized, equiaxed grain (10–15 m) microstructure in the weld zone.     

Investigation of the excitonic insulator phase in bismuth-antimony alloys

Pressure-induced metal-semiconductor transitions in bismuth-antimony alloys in a strong magnetic field (up to 70 kOe) at helium temperatures have been investigated. It is found that for values of the overlap-gap |G|1 meV the alloy forms an excitonic insulator (EI) in magnetic fields above a certain threshold (30–40 kOe). It is inferred that the EI energy gap increases with the magnetic field. The maximum gap observed in fields of 70 kOe turns out to be ₀₀7.5 K. An analysis of the results shows that transitions to the EI phase are observed from both the semimetal and the semiconducting states. The critical transition temperatureT _c is related to the EI gap by the expressionT _c0.7. Arguments are advanced in support of the fact that the formation of the EI phase involves the pairing of electrons at theL point with holes at theT point.