非线性动态传感器系统的H模型神经网络辨识

针对非线性动态传感器模型辨识问题,提出一种新的Hammerstein模型神经网络结构辨识法。非线性动态传感器系统采用Hammerstein模型描述,将系统分解为非线性静态增益串接线性动态环节。再设计一种网络权系数对应于相应的Hammerstein模型参数的新型神经网络结构,推导了基于反向传播的网络权系数调整方法。通过网络迭代训练同时得到静态与动态两个环节的模型参数。最后通过一个H模型的数值仿真来验证方法的有效性,仿真结果表明所提辨识方法是有效的。     

Correlation analysis based MIMO neuro-fuzzy Hammerstein model with noises

A novel identification algorithm for neuro-fuzzy based MIMO Hammerstein system with noises by using the correlation analysis method is presented in this paper. A special test signal that contains independent separable signals and uniformly random multi-step signal is adopted to identify the MIMO Hammerstein system, resulting in the identification problem of the linear model separated from that of nonlinear part. As a result, it can circumvent the problem of initialization and convergence of the model parameters encountered by the existing iterative algorithms used for identification of MIMO Hammerstein model. Moreover, least square method based parameter identification algorithms of dynamic linear part and static nonlinear part are proposed to avoid the influence of noise. Examples are used to illustrate the effectiveness of the proposed method.     

Optimal input design for set-membership identification of Hammerstein models

In this paper the problem of optimal input design for the identification of Hammerstein models is considered under the assumption that the linear dynamic part of the model is a FIR and that lower and upper bounds are available for the additive measurement errors. The parameters of the Hammerstein model can then be estimated via the identification of a linearized augmented Hammerstein model . External approximations of the feasible intervals for the parameters of the original Hammerstein models are then derived (which may correspond to the actual feasible intervals). This paper deals with the design of input sequences minimizing parameter uncertainty for the linearized augmented Hammerstein model . Some new results are also reported about optimal input design for polynomial non-linear blocks, that may be part of Hammerstein models.     

含有色噪声的神经模糊Hammerstein模型分离辨识

针对实际工业过程中普遍存在的有色噪声,本文提出一种基于递推增广最小二乘算法的神经模糊Hammerstein模型辨识方法,突破了传统的Hammerstein模型迭代分离算法.首先,利用多信号源实现Hammerstein模型中静态非线性环节和动态线性环节的分离,大大简化了辨识过程,提高了串联环节参数的分离精度.其次,利用长除法将噪声模型用有限脉冲响应模型逼近,采用增广递推最小二乘法进行线性环节的参数估计.最后,采用神经模糊模型拟合静态非线性环节,同时设计了神经模糊模型参数的非迭代优化算法,改善了模型的使用范围.该方法保证了模型的预测精度,对含有色噪声的非线性系统具有较好的拟合效果.仿真结果验证了上述方法的有效性.     

Fast approximate identification of nonlinear systems

In this paper, a method is presented to extend the classical identification methods for linear systems towards nonlinear modelling of linear systems that suffer from nonlinear distortions. A well chosen, general nonlinear model structure is proposed that is identified in a two-step procedure. First, a best linear approximation is identified using the classical linear identification methods. In the second step, the nonlinear extensions are identified with a linear least-squares method. The proposed model not only includes Wiener and Hammerstein systems, it is also suitable to model nonlinear feedback systems. The stability of the nonlinear model can be easily verified. The method is illustrated on experimental data.     

Identification of Hammerstein systems with asymmetric dead-zone nonlinearities using canonical parameterized model

A non-iterative identification method with parameterization of the unknown dead-zone is proposed for Hammerstein systems in presence of asymmetric dead-zone nonlinearities.The canonical parameterized model which is a single expression without segmentation is utilized to describe the dead-zone,based on which a universal-type parametric model can be established to approximate the entire system.This model can be established without separating the nonlinear part from the linear part.The dead-zone parameters and the coefficients in the linear transfer function can be estimated simultaneously according to the proposed algorithm.Numerical experiments are presented to illustrate the effectiveness of the proposed scheme.     

Making parametric Hammerstein system identification a linear problem

In this paper, we study the identification of parametric Hammerstein systems with FIR linear parts. By a proper normalization and a clever characterization, it is shown that the average squared error cost function for identification can be expressed in terms of the inner product between the true but unknown parameter vector and its estimate. Further, the cost function is concave in the inner product and linear in the inner product square. Therefore, the identification of parametric Hammerstein systems with FIR linear parts is a globally convergent problem and has one and only one (local and global) minimum. This implies that the identification of such systems is a linear problem in terms of the inner product square and any local search based identification algorithm converges globally.     

Non-parametric identification of continuous-time Hammerstein systems using Gaussian process model and particle swarm optimization

This paper deals with a non-parametric identification of continuous-time Hammerstein systems using Gaussian process (GP) models. A Hammerstein system consists of a memoryless non-linear static part followed by a linear dynamic part. The identification model is derived using the GP prior model which is described by the mean function vector and the covariance matrix. This prior model is trained by the separable least-squares (LS) approach combining the linear LS method with particle swarm optimization to minimize the negative log marginal likelihood of the identification data. Then the non-linear static part is estimated by the predictive mean function of the GP, and the confidence measure of the estimated non-linear static part is evaluated by the predictive covariance function of the GP. Simulation results are shown to illustrate the proposed method.     

Application of ELM–Hammerstein model to the identification of solid oxide fuel cells

In this paper, a new method is proposed to identify solid oxide fuel cell using extreme learning machine–Hammerstein model (ELM–Hammerstein). The ELM–Hammerstein model consists of a static ELM neural network followed by a linear dynamic subsystem. First, the structure of ELM–Hammerstein model is determined by Lipschitz quotient criterion from input–output data. Then, a generalized ELM algorithm is proposed to estimate the parameters of ELM–Hammerstein model, including the parameters of linear dynamic part and the output weights of ELM. The proposed method can obtain accurate identification results and its computation is more efficient. Simulation results demonstrate its effectiveness.

     

Identification of nonlinear systems using a piecewise-linear Hammerstein model

In the paper a method for nonlinear system identification is proposed. It is based on a piecewise-linear Hammerstein model, which is linear in the parameters. The model and the identification algorithm are adapted to allow the parameter identification in the presence of a special form of the excitation signal. The identification method is derived from a recursive least-squares algorithm, which is properly adapted to take into account the proposed model structure and the properties of the identification signal. The applicability of the approach is illustrated by an example in which a discontinuous nonlinear static function is connected to a dynamic block.     

Separability of scalar random multisine signals

Random multisines have successfully been used as input signals in many system identification experiments. In this paper, it is shown that scalar random multisine signals with a flat amplitude spectrum are separable of order one. The separability property means that certain conditional expectations are linear and it implies that random multisines can easily be used to obtain accurate estimates of the linear time-invariant part of a Hammerstein system. Furthermore, higher order separability is investigated.     

Identification of MIMO Hammerstein models using least squares support vector machines

This paper studies a method for the identification of Hammerstein models based on least squares support vector machines (LS-SVMs). The technique allows for the determination of the memoryless static nonlinearity as well as the estimation of the model parameters of the dynamic ARX part. This is done by applying the equivalent of Bai's overparameterization method for identification of Hammerstein systems in an LS-SVM context. The SISO as well as the MIMO identification cases are elaborated. The technique can lead to significant improvements with respect to classical overparameterization methods as illustrated in a number of examples. Another important advantage is that no stringent assumptions on the nature of the nonlinearity need to be imposed except for a certain degree of smoothness.     

超磁致伸缩作动器的率相关Hammerstein模型与H∞鲁棒跟踪控制

利用Hammerstein模型对超磁致伸缩作动器（Giant magnetostrictive actuators,GMA）的率相关迟滞非线性进行建模,分别以改进的 Prandtl-Ishlinskii（Modified Prandtl-Ishlinskii）模型和外因输入自回归模型（Autoregressive model with exogenous input,ARX）代表Hammerstein模型中的静态非线性部分和线性动态部分,并给出了模型的辨识方法. 此模型能在1～100Hz频率范围内较好地描述GMA的率相关迟滞非线性. 提出了带有逆补偿器和H∞鲁棒控制器的二自由度跟踪控制策略,实时跟踪控制实验结果证明了所提策略的有效性.     

Non-linear system identification using the Hammerstein model

An algorithm for the identification of non-linear systems which can be described by a Hammerstein model consisting of a single-valued non-linearity followed by a linear system is presented. Cross-correlation techniques are employed to decouple the identification of the linear dynamics from the characterization of the non-linear element. These results are extended to include the identification of the component subsystems of a feedforward process consisting of a Hammerstein model in parallel with another linear system.     

废气氧传感器Hammerstein模型结构的确定

研究了废气氧(EGO)传感器Hammerstein模型结构辨识方法。静态非线性函数选用双曲正切与多项式组合形式,动态线性环节分别选用带外生变量的自回归(ARX)模型、输出误差(OE)模型和Box-Jenkins(BJ)模型结构。采用交叉准则法进行参数估计和阶次选择,通过仿真比较对模型进行检验。结果表明:最终输出误差(FOE)准则和最终预报误差(FPE)准则均适用于用估计数据选择阶次,但前者比后者更可靠。基于预测误差法的3阶OE模型和BJ模型均可用于EGO传感器Hammerstein模型动态线性环节的建模。     

基于滤波的分段线性Hammerstein系统的递推辨识方法

Hammerstein模型具有结构简单、能很好地反映典型非线性特性等优点, 一直是控制领域的重要研究内容之一. 本文主要研究输出误差自回归Hammerstein系统的辨识问题, 系统的输入非线性部分采用分段线性函数拟合,并引入切换函数和位置函数将其表示为线性参数表达式. 为克服有色噪声的干扰, 本文通过关键项分离和数据滤波技术, 建立系统的滤波辨识模型. 在此基础上, 文中提出了基于滤波的遗忘梯度算法, 基于滤波的递推广义最小二乘算法和基于滤波的多新息遗忘梯度算法估计未知参数. 本文通过仿真实例验证了所提算法的有效性, 证明了多新息理论的应用可以有效地提高递推算法的辨识性能.     

Frequency domain identification of Hammerstein models

Discusses Hammerstein model identification in the frequency domain using sampled input-output data. By exploring the fundamental frequency and harmonics generated by the unknown nonlinearity, we propose a frequency domain approach and show its convergence for both the linear and nonlinear subsystems in the presence of noise. No a priori knowledge of the structure of the nonlinearity is required and the linear part can be nonparametric.     

Identification of Hammerstein models for control using ASYM

Identification of single-input single-output Hammerstein models is studied in this work. The basic idea here is to extend the recently developed asymptotic method (ASYM) of linear model identification to include input non-linearity in the model set. First identification test design will be discussed. In parameter estimation, prediction error criterion is used in order to maintain consistence when the process is operating in closed-loop. A relaxation iteration scheme is proposed by making use of a model structure in which the error is bilinear in the parameters. The order of the linear part and nonlinear part are determined by looking at an output error related criterion which is control-relevant. The frequency domain upper error bound of the linear part will be derived and used for model validation. Simulation study will be used to illustrate the method and comparisons with other methods are also given.     

基于SVR的传感器Hammerstein模型辨识

提出一种基于支持向量回归机的非线性动态传感器Hammerstein模型辨识方法并给出了相关的数学理论及学习算法.在该模型中,用非线性静态子环节和线性动态子环节串联来描述传感器的非线性动态特性.再利用函数展开将模型的非线性传递函数转换为等价的线性中间模型,并通过SVR求取中间模型参数.最后,推导出中间模型参数与传感器Hammerstein模型参数之间的关系,并由该关系实现非线性静态环节和线性动态环节的同时辨识.用实际力传感器动态标定实验数据进行测试,结果表明与常规非线性传感器辨识方法不同,所提方法只需进行一次动态标定实验就能给出非线性动态模型的数学解析表达式.且建立的力传感器Hammerstein模型阶次为4,而线性动态系统模型则需要6阶才能达到相同的精度.因此该研究为传感器非线性动态系统辨识又提供了一种可选方法.     

Adaptive control of a class of multivariable nonlinear systems andconvergence analysis

Adaptive control is discussed of a class of multivariable nonlinear systems which can be characterized by a stochastic multivariable Hammerstein model whose linear part possesses an arbitrary interactor matrix. A simple suboptimal control law is derived which provides an efficient way to control a multivariable Hammerstein model whose linear part is not necessarily minimum phase. A direct adaption scheme is presented to implement the control law, and the global convergence of the algorithm is established