Simulation of fire scenarios due to different vehicle types with and without traffic in a bi-directional road tunnel

This paper presents findings obtained by CFD modelling for simulating the effects of fire due to different vehicle types in a bi-directional road tunnel. Four different burning vehicles placed in the centre of the driving lane at tunnel middle length were considered. Peaks of the heat release rate (HRR) of: 8, 30, 50, and 100 MW were simulated for the two cars, the bus, the heavy goods vehicle (HGV), and the petrol tanker, respectively. The fire effects on tunnel structure and on environmental conditions along people evacuation path were especially evaluated. The effects of the traffic jam, in contrast with the isolated vehicles, on temperatures, radiant heat flux, visibility distance, and toxic gases concentrations, were also investigated. The worst scenario was identified to be that pertaining to the petrol tanker and more critical conditions were also found when the tunnel was full of vehicles. The maximum gas temperatures reached in the presence of traffic at the side wall (and at the tunnel ceiling reported in brackets) were found to be: 360 °C (170 °C) for the two cars; 740 °C (465 °C) for the bus; 835 °C (735 °C) for the HGV and 1305 °C (1145 °C) for the petrol tanker, respectively. The presence of the traffic, in contrast with the isolated vehicle, involved an increase in the maximum temperatures equal to 16–17% for the two cars, and contained in the range 12–29% with percentages increasing starting from the tanker, to the HGV and to the bus. In other words when the maximum temperatures produced by the isolated vehicle are very high (e.g. for the tanker), the presence of the traffic had a minor effect. With reference to environmental conditions along the evacuation path, the results showed that in the case of petrol tanker fire the emergency ventilation ensures a tenable level of temperature, radiant heat flux, and toxic gases concentrations up to 5 min from the fire starting. This time increases up to 6.5 min for the HGV and 8 min for the bus. This means that the tunnel users in order to be safe in all scenarios should leave the tunnel within 5 min after the fire starting. Toxic gases concentrations, however, were found to be below the limit values in all cases and also in the presence of traffic. In the light of the aforementioned results, tunnel occupants should be promptly informed of the fire risk and guided to the exit portals. This might be done by equipping the tunnel with illuminated emergency signs located along the tunnel length and by installing traffic lights before the entrances so that the tunnel can be closed in case of emergency. By activating the traffic lights at the portals and the emergency signs (more especially those at the ceiling) at the same time as the emergency ventilation is activated, safer conditions for the people evacuation are expected.     

CFD analysis of a realistic reduced-scale modeling equipped with axial jet fan

Typically, in the experimental scale road tunnel model, the air flow induced by ventilation system is provided by an external fan. In this paper, the authors have numerically simulated full and reduced-scale tunnel in order to evaluate the possibility to realize a reduced scale of a road tunnel model with a realistic ventilation system consisting of impulsive jet fans.In particular, two different types of longitudinal ventilation systems were considered, traditional and alternative. The last one was equipped with jet fans that have the inlet/outlet sections inclined at a fixed pitch angle (α=6°) toward the tunnel floor. The jet fan was simulated as a simple momentum source that provides a pressure rise (pressure drop) across them as a function of the outflow air velocity.The analyzed tunnel consists in a 800 m one directional bore with circular cross section 5.05 m radius; the jet fans were installed at 5.67 m from the floor. Furthermore a burning Heavy Good Vehicle (HGV), placed at 450 m far away the tunnel entrance, was considered. To simulate numerically the burning vehicle, the species transport equation combustion model with Eddy-Dissipation-Concept (EDC) model was adopted.In order to create a reduced-scale model from a full scale, Froude method was applied to preserve geometrical, kinematical and dynamical similitude. Temperature and axial velocity profiles, in different tunnel sections for both considered models (full and scaled) and ventilation systems, were provided. The numerical results showed a good agreement for the both ventilation systems.     

Upgrading the Arlberg tunnel to current safety standards

Austrian road tunnels within the Trans-European Road Network (TERN) must fulfil the requirements of the Directive 2004/54/EC (European Commission, 2004) not later than April 2019. This regulation has to be applied to all tunnels in the TERN with a length of more than 500 m, whether they are in operation, under construction or at design stage, and aims at ensuring a minimum level of safety for road users. One of the main features of this directive is the requirement for providing an egress possibility to a safe environment every 500 m throughout the whole tunnel.The Arlberg road tunnel has a length of some 15.5 km and is in operation for more than 35 years. It is a single tube tunnel operated with bi-directional traffic, but carries a quite low traffic volume. Hence, the construction of a second tube is not really cost effective. Currently the tunnel is equipped with a transversal ventilation system with remotely controlled smoke extraction dampers providing smoke extraction every 100 m. The maximum distance between egress possibilities to a save environment is some 1500 m. Due to the high costs of a construction of a second tube or a parallel running escape gallery, a novel solution was found. The existing fresh air duct will be used as safe escape way between the existing egress possibilities. This solution has big impacts on the ventilation system and on the requirements for thermal structure protection of the new egress ways, i.e. the fresh air duct. In order to overcome this problem, massive changes in the ventilation design have to be performed, accompanied by the installation of a high-pressure water-mist system for structure protection.     

Occupancy density and benefits of demand-controlled ventilation in Norwegian primary schools

One hundred and fifty-seven classrooms for fourth form pupils were inspected at 81 randomly selected schools in Oslo, Norway. Primary school classrooms in Oslo have on average 22 occupants present, while the maximum capacity is 30. Classrooms are typically used 4 h daily for normal school activities. The corresponding ventilating air volume and energy use has been analysed for three ventilation strategies: (a) constant air volume [CAV], (b) CO₂ sensor based demand-controlled ventilation [DCV-CO₂], and (c) infrared occupancy sensor based demand-controlled ventilation [DCV-IR].DCV-CO₂ and DCV-IR reduce the energy use due to ventilation in the average classroom to 38% and 51%, respectively, compared to the corresponding energy use for a CAV system operating with full airflow from 7:00 am to 5:00 pm.     

Possibility of using roof openings for natural ventilation in a shallow urban road tunnel

Naturally ventilated urban vehicular tunnels with multiple roof openings have increased in China. Unnecessary gas (polluted air or fire smoke) are expected to be exhausted out through openings. Whether its safety standards can be satisfied or not still needs to be verified. In this paper, a safe CO concentration was firstly discussed, and a heat risk level of very high to extreme up to 46 °C was given. Secondly, a real 1410 m tunnel was proposed, and a 1/10 scale model tunnel was reproduced. Ambient winds of 0.95 m/s in prototype and 0.3 m/s in model were considered. Under normal traffic test, a track circuit was constructed with model vehicles moving on it to form traffic wind, and once the air velocity was larger than 0.31 m/s, the airflows were found to be not relevant to the Reynolds number. The traffic winds were weakened by openings. For three of all tested traffic, the actual air velocities were larger than the required ones, so its air qualities were satisfied. In firing test, two sets of burning experiments were conducted with which the heat release rates (HRR) were 8.35 kW and 13.7 kW. Large amounts of smoke were exhausted out of openings, and the high-temperature was not significant. Full-scale numerical simulations were carried out to verify the experimental results respectively using Fluent 6.0 for normal traffic and FDS 4.07 for firing. The simulations were compared well with the experiments. Further FDS simulations show that the openings’ mass flow rates are influenced little by ambient temperature; with the increasing length of the buried section, much smoke accumulate inside leading to a high temperature; having 4–5 openings in one shaft group is oversize in the actual engineering design.     

Critical ventilation velocity for multi-source tunnel fires

Ventilation is an effective method for controlling smoke during a fire. The “critical ventilation velocity” u_cr is defined as the minimum velocity at which smoke is prevented from spreading under longitudinal ventilation flow in tunnel fire situations. All previous studies on this topic have simulated fire scenarios in which only one fire source exists. This study conducted small-scale experiments and numerical simulations to investigate u_cr for cases in which two tunnel fires occur simultaneously. The tunnel was 4 m long, 0.6 m wide and 0.6 m tall. Three cases of two variously separated fires were experimentally explored and six cases were examined numerically. Both the experimental and simulation results indicated that for two identical fires, u_cr declines with separation. When the two fire sources are separate completely, u_cr can be determined by considering only a single fire. When the larger fire is upstream of the smaller downstream fire, u_cr also decreases with the separation. When two such fires sources are completely separate, u_cr can be evaluated by considering only the larger fire. The concurrent ventilation flow and flow of downstream smoke from the larger fire are strong enough to suppress the smoke flow from the smaller fire. However, when the smaller fire is upstream of the larger fire, the decrease in u_cr becomes insignificant as distance increases and the flow at u_cr must overcome the flow from both fires.     

Investigation of the effect of tunnel ventilation on crib fires through small-scale experiments

This paper adopts a series of 1:20 scale tunnel experiments based on a series of large-scale tunnel experiments to study the influence of forced ventilation on fires. The small-scale tunnel has dimensions of 0.365 m (W)×0.26 m (H)×11.9 m (L). Cribs using a wood-based material provide the fuel source and forced ventilation velocities from 0.23 to 1.90 m/s are used. From the study of the measured heat release rate (HRR) and mass loss rate data it is found that the forced air velocity affects the fire spread rate and burning efficiency and further affects peak HRR values at different air velocities. A simple model to describe these influences is proposed. This model is used to reproduce the enhancement of peak HRR for cribs with different porosity factors noted by Ingason [1] and to assess the effects of using different length of cribs on peak HRR. The results from these analyses suggest that different porosity fuels result different involvement of burning surface area and result different changes in peak HRR. However, no significant difference to the enhancement on fire size is found when the burning surface area is similar. It is also found that the trend in the enhancement on fire size by using sufficiently long crib and available ventilation conditions matches the predictions of Carvel and Beard [2] for two-lane tunnel heavy goods vehicle fires.     

Load transfer mechanism in pile group due to single tunnel advancement in stiff clay

Construction of tunnels in urban cities may induce excessive settlement and tilting of nearby existing pile foundations. Various studies reported in the literature have investigated the tunnel–soil–pile interaction by means of field monitoring, centrifuge and numerical modelling. However, the load transfer mechanism between piles in a group, the induced settlement and the tilting of a pile group due to tunnel advancement has not been investigated systematically and is not well understood. This study conducts three-dimensional, coupled-consolidation finite element analyses to investigate tunnelling effects on an existing 2 × 2 pile group. The construction of a 6 m diameter (D) tunnel in saturated stiff clay is simulated. Responses of the pile group located at a clear distance of 2.1 m (0.35D) from a tunnel constructed at three different cover-to-diameter-of-tunnel ratios (C/D) of 1.5, 2.5 and 3.5 are investigated. The computed results are compared to published data based on field monitoring. It is found that the most critical stage for settlement, tilting and induced bending moment of pile group due to tunnelling is when the tunnel face is close to the pile group rather than at the end of tunnel excavation. The depth of the tunnel relative to the pile group has a vital influence on the settlement, tilting of pile group and the load transfer mechanism between piles in pile group induced by tunnel excavation. Tunnelling near the mid-depth of the pile group (i.e. C/D = 1.5) induces the largest bending moment in the piles, but the settlement and tilting of the pile group are relatively small. Based on a settlement criterion, apparent loss of capacity of the pile group is 14% and 23% for tunnels constructed at depths of C/D = 1.5 and at both C/D = 2.5 and 3.5, respectively. The largest load redistribution between the front and rear piles in the group and the largest tilting of the pile cap towards the tunnel occurs when tunnel excavated at C/D = 2.5.     

Numerical analysis of different ventilation schemes during the construction process of inclined tunnel groups at the Changheba Hydropower Station,China

During the excavation process of underground caverns, the rational selection of the ventilation scheme is very important for the safety and health of construction workers. The flood discharge tunnel groups at the Changheba Hydropower Station are selected as a case to study the design of ventilation schemes in inclined tunnel groups; these groups are characterized by a gradient of approximately 10% and a complex intersecting relationship among the tunnels. The Computational Fluid Dynamics (CFD) method is used to simulate the fluid dynamics in tunnel groups when different ventilation schemes are employed. Four ventilation schemes with the same duct at different positions along the transverse section are formulated, and the scheme approaching the right side with most of the construction adits is adopted in engineering after a comparative analysis, as it offers a well-distributed velocity field and sufficient security distance. The study reveals that flow vortices appear in the tunnels with a long axis length ranging from 5 m to 20 m; the observation that the flow velocity on the transverse sections is away from the heading face indicates that a low-velocity area is always present in the vicinity of an air duct, and the security distance on the upstream side is 60% shorter than on the downstream side with the same air-blower when the tunnels have a 10% gradient. In addition, when the excavation distance rises 200 m, the ventilation condition in the tunnels, especially in the areas around tunnel intersections, is greatly improved by the completion of pilot tunnels and shafts in advance.     

Numerical simulation of air ventilation in super-large underground developments

Recent advancements in engineering technology have enabled the construction of super-large underground engineering projects in China. Currently, the ventilation requirements and standards of normal-size underground spaces are used for super-large underground excavating engineering projects in China. For example, the minimum air velocity of 0.15 m/s is the standard velocity for normal-size underground spaces; however, this value is also used as the required air velocity for diluting underground contaminants in super-large underground developments. This paper aims to examine the minimum ventilation requirements for super-large underground developments (S > 100 m²). A three-dimensional computational domain representing a full-scale underground space has been developed. The pertinent parameters such as dust concentration, smoke density, oxygen concentration and air temperature have been simulated. The results show that at some specific underground conditions, the ventilation air velocity of 0.15 m/s is sufficient to control the dust level, provide required oxygen concentration and maintain the air temperature at acceptable levels during development; however, it is not sufficient to bring the CO concentration below an acceptable safe limit. This must be considered by the ventilation system designers of super-large underground developments.     

Velocity and temperature attenuation of a ceiling-jet along a horizontal tunnel with a flat ceiling and natural ventilation

A series of fire tests was conducted in a small-scale tunnel with dimensions of 10.0 m (L) × 0.75 m (W) × 0.45 m (H) and a rectangular cross-section. Detailed measurements of the velocity and temperature within a steady fire-driven ceiling-jet running along the centre of the ceiling were conducted.Referring to a theoretical derivation process described in the literature as a starting point, correlations representing the velocity and temperature attenuation along the tunnel axis were developed.The values of the coefficients included in the developed correlation for the velocity attenuation were measured using a particle image velocimetry system during the experiments conducted in the small-scale tunnel. The value of the Stanton number was determined by considering the ceiling-jet thickness, which was derived from the velocity distribution. The values of the coefficients included in the developed correlation for the temperature attenuation were also determined based on experimental results described in the literature, which were obtained in a large-scale tunnel constructed using good heat insulation properties.Through these correlations developed for the velocity and temperature attenuations along the tunnel axis, the variation in the Richardson number of the ceiling-jet based on the distance from the fire source position along the tunnel axis was examined, and the position where the ceiling-jet changed from a shooting flow to a tranquil flow was determined. The boundary positions between the shooting and tranquil flows were determined using correlations between the velocity and/or temperature attenuation, which were compared with the variation in the Richardson number along the tunnel axis to verify their appropriateness.     

Studies on buoyancy driven two-directional smoke flow layering length with combination of point extraction and longitudinal ventilation in tunnel fires

This paper investigates the buoyancy-driven smoke flow layering length (both upstream and downstream) beneath the ceiling with combination of point extraction and longitudinal ventilation in tunnel fires. A theoretical model is developed based on previous back-laying model with only longitudinal ventilation, with modified actual heat release rate, as well as modified upstream and downstream opposing longitudinal air flow velocities by the induced flow velocity due to point extraction. Experiments are carried out in a reduced scale model tunnel with dimensionless of 72 m×1.5 m×1.3 m. A LPG porous gas burner is used as fire source. The smoke flow layering length both upstream and downstream are identified based on temperature profiles measured along the ceiling, for different experiment conditions. CFD simulations with FDS are also performed for the same scenarios. Results show that with combination of point extraction and longitudinal ventilation, the smoke flow layering length is not symmetric where it is longer downstream than that upstream. The upstream smoke layering length decreases, while the downstream layering length increases with increase in longitudinal ventilation velocity; and they both decrease with increase in point extraction velocity. The predictions by the proposed theoretical model agree well with the measurements and simulation results.     

Impact of fugitive emissions in ambient PM levels and composition: A case study in Southeast Spain

The results of this study show the high impact that anthropogenic fugitive emissions of mineral dust have on air quality (levels of PM₁₀, PM_2.5 and some metals) in a region in SE Spain named L'Alacantí. This could be extensive to other areas of Europe with similar characteristics. Fugitive emissions, such as those arising from large public construction works, cement and ceramic manufacturing, mining, heavy industries, handling and transport of powdered raw materials and road dust, are very often left out of emission monitoring and inspections in Europe. The comparative study of daily PM₁₀ series in the area shows how the increase of annual average PM₁₀ concentrations over 40 μg/m³ is due to extreme episodes occurring in 2006 and 2007, at a regional scale, given the simultaneous recording of PM episodes at distant monitoring sites. The annual average values of the PM₁₀ concentrations were close to or slightly higher than 40 μg/m³ (limit value of Directive 2008/50/CE) during 2006–2007 (Alicante-University 39–41, Agost 40–42, Sant Vicent 42–46, Alicante-El Plà 40–42 μg/m³). The main PM₁₀ sources in the zone were identified with the assistance of the PMF receptor model. Six common factors were determined, mineral as a main source (37% at Agost and 32% at Sant Vicent), road traffic, secondary sulfate, petroleum coke, sea spray and industry. Mineralogical studies, with XRD and SEM-EDX techniques, support the hypothesis that the highest PM episodes are associated to fugitive emissions of mineral matter. Despite the fact that L'Alacantí region is a heavily industrialized area with two cement plants and a significant number of ceramic manufacturing plants, the fugitive emissions may have accounted for the exceedances of the PM limit values during these two years, part of them caused by the construction of a highway. These results may contribute to the interpretation of prior studies on source apportionment carried out in Southern Europe, with very high loads of anthropogenic dust in PM₁₀ and PM_2.5.     

Automatic fire detection in road traffic tunnels

Fire detection experiments in a road traffic tunnel were performed in the Runehamar test tunnel 5th–8th March 2007. The Runehamar test tunnel is a full profile road traffic tunnel, 1.65 km long, located outside Åndalsnes, Norway. The goal was to examinate smoke and heat detection systems to determinate what kind of principle best suited for detecting a fire in an early stage. The systems were tested during small Heptane pool fires, varying between 0.16 m² and 1 m², giving heat release rates from 0.2 MW to 2.4 MW accordingly, and one car fire of about 3–5 MW, and with wind conditions varying from 1.1 m s^?1 to 1.6 m s^?1. The size of the fires, were designed to be in the range from impossible to difficult to detect. The results were conclusive. Earliest detection of a car fire, fire starts inside, was by smoke detection given fixed limits (3000 μg m^?3). With open pool fires, or immediate flames, continues fibre optical heat detection systems was faster given the limits 3 °C/4 min.     

The effect of fuel area size on behavior of fires in a reduced-scale single-track railway tunnel

A set of experiments was carried out in a 1/9 reduced-scale single-track railway tunnel to investigate the effect of fuel area size on the temperature distribution and behavior of fires in a tunnel with natural ventilation. Methanol pool fires with four different fuel areas 0.6 × 0.3 m² (1 pan), 1.2 × 0.3 m² (2 pans), 2.4 × 0.3 m² (4 pans) and 3.6 × 0.3 m² (6 pans), were used in these experiments. Data were collected on temperatures, radiative heat flux and mass loss rates. The temperature distribution and smoke layer in the tunnel, along with overflow dimensions and radiant heat at the tunnel entrance were analyzed. The results show that as the fuel area enlarges, the fire gradually becomes ventilation-controlled and the ceiling temperature over the center of fire source declines. Burning at the central region of fire source is depressed due to lack of oxygen. This makes the temperature distribution along the tunnel ceiling change from a typical inverted V-shape to an M-shape. As observed in the experiments, a jet flame appeared at tunnel entrances and both the size and temperature of the flame increased with the enlargement of fuel area leading to a great threat to firefighters and evacuees in actual tunnel fires.     

Numerical comparison of performance between traditional and alternative jet fans in tiled tunnel in emergency ventilation

In this paper a computational study was carried out to evaluate the performance of longitudinal ventilation system equipped with an alternative jet fan with respect to traditional one in case of fire in tiled tunnel. The alternative jet fan is equipped with inclined silencers (pitch angle α = 6°) in order to reduce the Coanda effect and consequently shear stress on the tunnel ceiling. The fire was simulated setting heat flux on HGV surface. Computational fluid dynamic analysis was applied to simulate the ventilation in the unidirectional tunnel through κ–ɛ model. The comparison conducted in terms of total thrust required to prevent back-layering phenomena and numerical results were provided in terms of thrust of jet fan values, average velocity values and temperature profiles, for different tunnel slope values. Furthermore the authors have compared the critical velocity provided by CFD analysis with critical velocity provided in the literature.     

Ceiling-jet thickness and vertical distribution along flat-ceilinged horizontal tunnel with natural ventilation

A series of fire tests was conducted in a 10.0 m (L) × 0.75 m (W) × 0.45 m (H) model tunnel with a rectangular cross section, and detailed measurements were taken of the temperature and velocity within a quasi-steady state fire-driven ceiling-jet running along the centre of a ceiling.The ceiling-jet thickness was defined as the distance from the tunnel ceiling to the point where the temperature and/or velocity dropped to half of their maximums. Correlations to represent the variation in the ceiling-jet thickness along the tunnel axis were developed with the aid of a theoretical approach. The coefficients included in these correlations were determined based on the experimental results obtained. It was found that the ceiling-jet thickness derived from the temperature was 1.17 times greater than that from the velocity in the tranquil flow region.In the tranquil region, both the velocity and temperature showed top-hat distributions, with a bulging shape from the apex of the distribution towards the tunnel floor. A cubic function and coordinate transformation were applied to develop empirical formulae for the temperature and velocity distributions, which were represented by the dimensionless distance from the tunnel ceiling and dimensionless temperature rise and/or velocity at a given distance from the fire source. The correlation developed for the temperature distribution was compared with the results of large- and full-scale tunnel experiments, which verified its applicability.     

Experiments of evacuation speed in smoke-filled tunnel

Among tunnel fire safety strategies, evacuation speed in smoke, which is the basic evacuation performance characteristic, is one of the most important factors when assessing safety. An evacuation experiment in a full-scale tunnel filled with smoke has been done in order to clarify the relation between extinction coefficient up to Cs = 1.0 m⁻¹, which includes Cs = 0.4 m⁻¹ as a Japanese road tunnel fire prevention standard, and evacuation speed. The maximum, minimum and mean values of normal walking speeds are almost constant regardless of the extinction coefficient. As for the emergency evacuation speeds, the maximum speed is largely influenced by extinction coefficient, decreasing rapidly from 3.55 m/s at Cs = 0.30 m⁻¹ to 2.53 m/s at Cs = 0.75 m⁻¹ while the minimum and mean speeds are almost constant with a slight decrease as Cs increases. The maximum evacuation speed trends in the present experiments and those in Frantzich and Nillson (2003, 2004) and Fridolf et al. (2013), lie on the same decreasing logarithmic curve as a function of extinction coefficient.     

Maximum surface settlement based classification of shallow tunnels in soft ground

Prediction of the maximum surface settlement due to shallow tunnelling in soft grounds is a valuable metrics in ensuring safe operations, particularly in urban areas. Although numerous researches have been devoted to this issue, due to the complexity and a large number of the effective parameters, no comprehensive solution to the problem is available. In this study, a shallow tunnel classification system (STCS), based on maximum settlement, is proposed. The STCS holds on the results of several tunnelling projects around the world. The classifier categorises a tunnel based on geometry, ground, and performance characteristics. A decision tree classification method, after training with 20 cases, was successful to predict the maximum settlement for 14 tunnelling projects. The maximum surface settlement predictions were in the form of assigning a class label to each tunnel. Four tunnel classes were defined as follow: (i) class A (maximum settlement < 9.9 mm), (ii) class “B” (10 ⩽ maximum settlement < 19.9 mm), (iii) class “C” (20 ⩽ maximum settlement < 29.9 mm), and (iv) class “D” (maximum settlement ⩾ 30 mm). The most explanatory independent variables were selected, by the STCS, as follow: tunnel depth, diameter, volume loss, and normalised volume loss. The proposed classification scheme can be employed as a decision making aid in settlement prediction/prevention in shallow tunnelling in soft grounds. The STCS is proposed as a supplemental tool to the observational methods, and it is not expected to be a stand-alone measure for settlement.     

Night ventilation and active cooling coupled operation for large supermarkets in cold climates

Night ventilation and active cooling coupled operation strategy is studied for the large supermarkets in cold climates in China. The model on the thermal storage of the indoor goods is set up. Furthermore, based on the thermal balance of the whole room, the temperature change model is founded. The coupled operation process is simulated for the typical supermarket buildings. The overall energy consumption of the system is analyzed. The result shows that the opening time, duration and air flow rate of night ventilation all affect the performance of active cooling. Active cooling will influence night ventilation too. It also turns out that the coupled operation leads to shorter operation time of active cooling. The various operation modes are given at different climatic conditions. Compared with the normal active cooling system, the coupled operation system can save energy at 2.99 kWh/(m² a) in cold climates in China while 3.24 kWh/(m² a) in Harbin.