Creep features of Al2O3-Al alloy composites

Creep features of two cast aluminium alloy composites reinforced by Al₂O₃ short fibres randomly oriented in the matrices have been studied at 300 °C and several stress levels. The presence of short-term negative creep in primary creep is an important feature for the composites, which resulted from randomly oriented fibres strongly resisting dislocation creep in the matrix. However, the negative creep magnitude depended on both the applied stress and the nature of the material. There was a critical stress for the presence of the short-term negative creep. When the applied stress had exceeded the critical value, the negative creep disappeared. Fibres traversing grain boundaries can reinforce and resist grain boundary sliding at elevated temperature. The effect of stress on creep rate for the composites is not so strong as that for unidirectional metallic matrix composites. During the creep, some intermetallic phases in the Al₂O₃/Al-5Si-3Cu-1 Mg composite were precipitated and most of them were segregated at grain boundaries, leading to a small increase of the creep rate.     

Sliding wear of Al2O3P/6061 Al composite

The mild sliding wear behaviour of a 15 vol % Al₂O_3P/6061 Al composite has been investigated by using a pin-on-disc reciprocating sliding machine. The composite has been shown to exhibit an excellent wear resistance as compared to the unreinforced matrix alloy. The wear rate of the composite under dry wear conditions with a 12N load is approximately one tenth of that in the 6061 aluminium alloy. The wear rate of the composite under lubrication with 15W/40 gear oil under a 100N load is only one thousandth ofthat in the 6061 aluminium alloy.The dry wear resistance of an over-aged sample is shown here to be better than a peak aged or under-aged sample when the composite was aged at 160°C. The coefficient of friction of the composite was approximately 0.5–0.6 under dry conditions and 0.07 in lubricated wear experiments.In the initial stage, the worn surface of the composite under dry conditions is primarily composed of ploughed grooves and ductile tear. The composite makes a conducting contact with the steel pin. The worn surface is composed of compacted powder and the contact potential gradually increases when the period of the wear experiment goes beyond 2 h.     

Grain boundary analysis of MgO-doped Al2O3

Grain boundaries of MgO-doped alumina also containing CaO have been investigated by various authors. The general conclusion of this work is that Ca is enormously enriched at the grain boundaries compared with Mg, which was found either to be slightly or not at all enriched at the grain boundaries. Electron scanning chemical analyses of predominant intergranular fracture surfaces of alumina samples containing different amounts of MgO (100, 250, 1000 and 2000 ppm), as described in this paper, show that Mg is enriched at the grain boundaries below the solubility limit. Above the solubility limit it is probable that MgAl₂O₄ precipitates contribute considerably to the Mg content measured at the boundaries. The amount of Mg segregated at the grain boundaries was found to be roughly independent of the amount of MgO added as long as the firing conditions were kept constant. The enrichment found, together with the effect of small amounts of MgO on the development of the microstructure, indicate the possibility that segregated Mg may still be active in the grain growth process.     

Al2O3/Al2O3 Joint Brazed with Al2O3-particulate-contained Composite Ag-Cu-Ti Filler Material

1.IntroductionTo improve the mechanical properties and relieve mis-matches between the filler metals and base materials,the particulates of superalloys,ceramic or carbon fiberswere added into the conventional brazing filler metal toform composite filler material.The method has beenused in aero-engine component repairing[1,2],fine castcomponent joining[3],wide clearance butt jointing[4],ce-ramic brazing[5,6]and electronic package[7].However,the method was used mostly in metal brazing.The mi-cro…     

Creep behaviour of Si3N4/Y2O3/Al2O3/AIN alloys

The compression creep behaviour of pressureless sintered Y₂O₃/Al₂O₃/AIN-doped Si₃N₄ was studied between 1473 and 1673 K, under stresses ranging from 100–300 MPa. Strain rate versus stress and temperature analysis give a stress exponent n1 and an activation energy Q=860 kJ mol^–1. Microstructural change was investigated by transmission electron microscopy. The observed strain whorls, the stress exponent and the activation energy are indicative of a solution-diffusion-precipitation accommodated grain-boundary sliding where the diffusion through the glass is rate controlling.     

Al2O3掺杂ZnO压敏陶瓷的晶粒生长研究

研究了Al2O3掺杂对ZnO压敏陶瓷晶粒生长规律的影响,应用晶粒生长动力学方程确定了晶粒生长的动力学指数和激活能.实验结果表明,对于Al2O3掺杂ZnO压敏陶瓷,其晶粒生长的动力学指数n等于4,激活能Q等于(400±26)kJ/mol.Al2O3掺杂ZnO压敏瓷的晶粒生长机理是ZnAl2O3尖晶石颗粒在ZnO压敏瓷晶粒边界钉扎过程中Al3+和O2-通过ZnAl2O4尖晶石的扩散.     

Grain Boundary Sliding in Fatigue of Pure Aluminum

The distributions of plastic strain near grain boundaries induced by fatigue loading were investigatedby the fiducial grid method in pure aluminum specimens, and the resulted grain boundary sliding(GBS) was systematically analysed. The results show that the strain field near a grain boundary isnonuniform. GBS is restricted by the junction of grain boundaries and causes discontinuities of bothdisplacement and strain. A peak value of shear strain was created in short-range area across the grainboundary. GBS plays an important role in cyclic softening and secondary hardening. The control fac-tor of GBS is the relative orientation between two grains and the macro orientation of the grainboundary rather than the ∑ value of the boundary.     

Healing of Planar Defects in 2D Materials via Grain Boundary Sliding

Understanding the mechanisms and kinetics of defect annihilations, particularly at the atomic scale, is important for the preparation of high‐quality crystals for realizing the full potential of 2D transition metal dichalcogenides (TMDCs) in electronics and quantum photonics. Herein, by performing in situ annealing experiments in an atomic resolution scanning transmission electron microscope, it is found that stacking faults and rotational disorders in multilayered 2D crystals can be healed by grain boundary (GB) sliding, which works like a “wiper blade” to correct all metastable phases into thermodynamically stable phases along its trace. The driving force for GB sliding is the gain in interlayer binding energy as the more stable phase grows at the expanse of the metastable ones. Density functional theory calculations show that the correction of 2D stacking faults is triggered by the ejection of Mo atoms in mirror twin boundaries, followed by the collective migrations of 1D GB. The study highlights the role of the often‐neglected interlayer interactions for defect repair in 2D materials and shows that exploiting these interactions has significant potential for obtaining large‐scale defect‐free 2D films.     

Plasma spraying of Al2O3 and Al2O3Y2O3

A microstructural study has been carried out of plasma-sprayed Al₂O₃ and mixed and sintered Al₂O₃Y₂O₃. In order to ascertain the degree of metastability achieved by plasma spraying, these results are compared with a similar experiment utilizing a CO₂ laser for melting and the hammer-and-anvil technique for quenching of the same materials. X-ray diffraction methods were used to determine the obtained phases and crystal structures. In addition, transmission electron microscopy was used to confirm the phases present and to study their morpology. The porosity was studied with both mercury intrusion porosimetry and small angle neutron scattering. The addition of Y₂O₃ is shown to decrease the porosity from 15% to 7.5%. Adhesion is likewise related to the addition of Y₂O₃ and it is seen that adhesion of the mixture is measurably improved over that of pure Al₂O₃. The implication of these results is discussed.     

Microstructure and Strength of Al2O3/Al2O3 Joints Bonded with ZnO-Al2O3-B2O3-SiO2 Glass-Ceramic

ZnO-Al2O3-B2O3-SiO2 （ZABS） glass powder was used as interlayer to join alumina ceramics. The effect of joining temperature on the microstructure and strength of joints was investigated. The results showed that the ZABS glass can react with alumina substrate to form a layer of ZnAl2O4 at Al2O3/glass interface. Bending test exhibited that low joining temperature （1150℃） led to low joint strength due to the formation of pores in the interlayer, originated by high viscosity of the glass. High joining temperature （1250 ℃） also resulted in low joint strength, because of large CTE （coefficient of thermal expansion） mismatch between amorphous interlayer and alumina substrate. Therefore, only when the joining temperature was appropriate （1200℃）, defect-free interface and high joint strength can be obtained. The optimum joint strength reached 285 MPa, which was the same as the base material strength.     

Surface,grain-boundary and interfacial energies in Al2O3 and Al2O3-Sn,Al2O3-Co systems

Using the multiphase equilibrium method for the measurement of contact angles, the surface and grain-boundary energies of polycrystalline Al₂O₃ in the temperature range of 1473 to 1923 K were determined. Linear temperature functions were obtained by extrapolation for both quantities between absolute zero and the melting point of Al₂O₃. The temperature dependence of the surface and grain boundary energies can be expressed as $$\gamma _{{\rm A}l_2 O_3 } = 2.559 - 0.784 \times 10^{ - 3} T(J m^{ - 2} )$$ and $$\gamma _{{\rm A}l_2 O_3 - Al_2 O_3 = } 1.913 - 0.611 \times 10^{ - 3} T(J m^{ - 2} )$$ respectively. The interfacial energies of Al₂O₃ in contact with the molten metals tin and cobalt revealed a linear dependence on temperature.     

Creep of Cr2O3 and yttrium doped Cr2O3

Abstract

Compressive creep tests of pure and Y doped Cr₂O₃ from 1217 to 1417°C have shown that the presence of Y substantially increases diffusional flow rates. It is suggested that this increase in deformation rate may account, in part, for the empirical evidence that improved adherence to the underlying metal is provided by Y containing scales compared with pure scales.

MST/819     

Al2O3—Coated Nano—SiC Particles Reinforced Al2O3 Matrix Composites

Properties of Al2O3-coated nano-SiC have been compared with those of as-received SiC.The isoelectric point(IEP) of SiC changed from pH3.4 to pH7.3 after coating with the alumina precursor,which is close to that of alumina.Because both surfaces of coated SiC and Al2O3 possess higher positive charge at pH=4.5-5.0 ,they are uniformly dispersed in the two-phase aqueous suspensions.Then a mixed powder containing nano-SiC dispersed homogeneously into the Al2O3 matrix was achieved from flocculating the two-phase suspension.Finally,Al2O3/SiC nanocomposited were obtained by coating nano-SiC with Al2O3 ,in which the majority of SiC particles were located within the Al2O3 grains.The observation by transmission electron microscopy(TEM) and the analysis by the X-ray photoelectron spectroscopy(XPS) showed that cracks propagated towards the intragranular SiC rather than along prain boundaries.     

Microstructure of the Al2O3/Al2O3 Joint Brazed with Cu-Zn-Ti Filler Metal

Microstructure and interface reactions of Al2O3 joints brazed by Cu-Zn-Ti alloy were studied by using SEM, EDS and XRD. The effects of brazing temperature and Ti content on interfacial reactions and microstructure were investigated, and the action of adding Zn into brazing alloy was also studied. TiO, Ti3Al and CuTi were formed at the interface of ceramics and the filler metal, while CuTi, Cu3Ti and alpha -Cu were found in the brazing. The thickness of the reaction layer increased with increasing of brazing temperature, under the same brazing process, the thickness increased with the Ti content.     

Atomistic Simulation of Interaction between Grain Boundary and Dislocations in Ni_3Al

The embedded atom type potentials and static relaxation method combined with a steepest decentcomputational technique have been used to simulate the interaction between the grain boundary(GB) and dislocations in Ni_3Al alloys.The focus has been placed on the energy feature of theinteraction,the distortion of GB structural units,and the dislocation core structure near the GB.Im-plication has also been made on the results for the understanding of the mechanism responsible forB-enhanced ductility.     

Microstrip losses with Al2O3 overlay

Microstriplines were coated with Al₂O₃ by chemical vapour deposition to get homogeneous thin film overlay. The paper reports the decrease in the total power loss in such microstrips. The frequency response from 2–6 GHz is studied for the overlay effect.