Kinetics of crystal nucleation of Na<Subscript>2</Subscript>O · 2CaO · 3SiO<Subscript>2</Subscript>-based solid solutions in glasses of the Na<Subscript>2</Subscript>SiO<Subscript>3</Subscript>—CaSiO<Subscript>3</Subscript> pseudobinary join

The kinetics of crystal nucleation is investigated in sodium calcium silicate glasses of two compositions (22.4 and 24.4 mol % Na₂O), which belong to the Na₂SiO₃—CaSiO₃ pseudobinary join and, according to the phase diagram, lie in the region of the formation of solid solutions between the compositions Na₂O · 2CaO · 3SiO₂ and Na₂O · CaO · 2SiO₂. The stationary rate of crystal nucleation of Na₂O · 2CaO · 3SiO₂-based solid solutions is measured as a function of temperature. It is shown that the maximum stationary rate of nucleation increases with an increase in the sodium oxide content in the initial glasses. The experimental data are analyzed in the framework of the classical nucleation theory.Original Russian Text Copyright © 2004 by Fizika i Khimiya Stekla, Soboleva, Yuritsyn, Ugolkov.     

Electrical properties of lead-free 0.98(Na<Subscript>0.5</Subscript>K<Subscript>0.5</Subscript>)NbO<Subscript>3</Subscript>-0.02Ba(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript> piezoelectric ceramics by optimizing sintering temperature

Lead-free 0.98(Na_0.5K_0.5)NbO₃-0.02Ba(Zr_0.52Ti_0.48)O₃ [0.98NKN-0.02BZT] ceramics were fabricated by the conventional mixed oxide method with sintering temperature at 1,080°C to 1,120°C. The results indicate that the sintering temperature obviously influences the structural and electrical properties of the sample. For the 0.98NKN-0.02BZT ceramics sintered at 1,080°C to 1,120°C, the bulk density increased with increasing sintering temperature and showed a maximum value at a sintering temperature of 1,090°C. The dielectric constant, piezoelectric constant [d ₃₃], electromechanical coupling coefficient [k _p], and remnant polarization [P _r] increased with increasing sintering temperature, which might be related to the increase in the relative density. However, the samples would be deteriorated when they are sintered above the optimum temperature. High piezoelectric properties of d ₃₃ = 217 pC/N, k _p = 41%, dielectric constant = 1,951, and ferroelectric properties of P _r = 10.3 μC/cm² were obtained for the 0.98NKN-0.02BZT ceramics sintered at 1,090°C for 4 h.     

Modification of Mg<Subscript>3</Subscript>Si<Subscript>2</Subscript>O<Subscript>5</Subscript>(OH)<Subscript>4</Subscript> nanotubes by magnetite nanoparticles

The magnetite nanoparticles and nanocomposite “Nanotube of hydrosilicate Mg—magnetite nanoparticles—Mg-ChR-NT/Fe₃O₄-NP” were obtained by coprecipitation. The composition of the synthesized samples has been established by X-ray diffraction. Using transmission electron microscopy, the presence of magnetite nanoparticles has been detected both inside the NTs and at the external surface of the NT walls. The specific surface of the NTs, nanoparticles, and composite is determined.     

Preparation of Si<Subscript>3</Subscript>N<Subscript>4</Subscript>–ZrO<Subscript>2</Subscript> ceramic composites by self-propagating high-temperature synthesis

Results are provided for a study of Si₃N₄–ZrO₂ composite ceramic material preparation by self-propagating high-temperature synthesis from ferrosilicon and zirconium concentrate. It is noted that as a result of high-temperature dissociation of ZrSiO₄ silicon dioxide is nitrided with formation of silicon oxynitride and it is condensed in surface layers of a specimen in the form of filamentary crystals.     

Effect of a novel intumescent retardant for ABS with synergist Al(H<Subscript>2</Subscript>PO<Subscript>2</Subscript>)<Subscript>3</Subscript>

A novel intumescent flame retardant (IFR), containing ammonium polyphosphate (APP) and poly(hexamethylene terephthalamide) (PA6T), was prepared for acrylonitrile–butadiene–styrene (ABS). Limiting oxygen index (LOI), vertical burning test (UL-94), thermogravimetric analysis (TGA) were used to investigate the flammability property and thermal stability of the IFR/ABS systems. It was found that the flame retardancy of the IFR/ABS systems was improved significantly. When the components of the IFR were 25% APP and 5% PA6T, the LOI value of IFR/ABS system reached to the maximum of 29, but only UL-94V-1 rating was passed. Thus, Al(H₂PO₂)₃ was incorporated into ABS/APP/PA6T system as a synergistic agent, it was found 2% addition of Al(H₂PO₂)₃ caused PA6T/APP/PA6T/Al(H₂PO₂)₃ (70/23.3/4.7/2) to pass V-0 rating of UL-94 test. Meanwhile, the TGA curves indicated that PA6T could be effective as a charring agent and there was a synergistic reaction between PA6T and APP, which effectively promoted the char formation of IFR/ABS composites. Moreover, the residual char obtained after the LOI test of the IFR/ABS was characterized by Fourier transform infrared spectra (FTIR). Results indicated that P–O–C chemical bond was formed in the residual char, which could indicate the cross-linking reaction between PA6T and APP could occur. Furthermore, scanning electron microscopy (SEM) was used to investigate the morphology of the residual char formed in the LOI tests. It was revealed that both ABS/APP/PA6T (70/25/5) and PA6T/APP/PA6T/Al(H₂PO₂)₃ (70/23.3/4.7/2) formed uniform and compact intumescent charred layers.     

Electrical conductivity and structure of glasses in the Na<Subscript>2</Subscript>O-Na<Subscript>2</Subscript>S-P<Subscript>2</Subscript>O<Subscript>5</Subscript> and Na<Subscript>2</Subscript>S-P<Subscript>2</Subscript>S<Subscript>5</Subscript> systems

The glasses, in which oxygen was partially replaced with sulfur, have been synthesized in the Na₂O-P₂O₅-Na₂S system. The chemical and chromatographic analyses of the glasses synthesized have been performed. The temperature-concentration dependences of electrical conductivity of the glasses have been studied over a wide temperature range; the glass transition temperatures and the nature of charge carriers have been determined. The IR spectra and Raman spectra have been recorded at room temperature; the density and microhardness of the glasses and ultrasound velocity have been measured. A comparison of the electrical conductivities of the investigated glasses with those of the earlier studied glasses in the Na₂O-P₂O₅ system has shown their fair coincidence. The introduction of sodium sulfide into the Na₂O-P₂O₅ system is accompanied by an approximately threefold increase in electrical conductivity, although the concentrations of charge carriers (sodium ions) in the glasses amount to ∼17 and ∼26 mmol/cm³, respectively. The rise in electrical conductivity has been assumed to be caused by the increase in the degree of dissociation of polar structural chemical units including sulfide ions and by the higher mobility of sodium ions in the oxygen-free matrix.     

Mechanism of formation of the complex oxide Na<Subscript>2</Subscript>Nd<Subscript>2</Subscript>Ti<Subscript>3</Subscript>O<Subscript>10</Subscript>

The processes of phase formation in the Nd₂O₃-TiO₂-Na₂CO₃ system have been investigated in the temperature range 500–1100°C. The mechanism of the high-temperature solid-phase reaction of formation of the complex oxide Na₂Nd₂Ti₃O₁₀ has been studied. It has been established that the Na₂Nd₂Ti₃O₁₀ compound is formed from the intermediate product Na_0.5Nd_0.5TiO₃ with a perovskite structure in the temperature range 830–890°C and from the NaNdTiO₄ oxide with a perovskite-like layered structure in the temperature range 960–1100°C.     

Combustion and structure formation in the Ti-Ta-C-Ca<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> system

Biocompatible composites (Ti, Ta)C _x + Ca₃(PO₄)₂ for deposition of nanofilms onto load-bearing implants by ion-plasma sputtering were prepared from Ti + Ta + C + Ca₃(PO₄)₂ mixtures by forced SHS compaction. The effect of Ta + C addition to green mixtures (characterized by parameter z) on the structure/phase formation in combustion products was explored. The addition of tantalum and carbon was found to have little or no influence on the burning velocity U and combustion temperature T _c. Two thermal spikes exhibited by thermograms were associated with the occurrence of two consecutive reactions leading to formation of titanium and tantalum carbides. With increasing z, the grain size of (Ti, Ta)C was found to diminish, its relative density to decrease, while the hardness to markedly grow.      

Thermochemical modification of Mg<Subscript>3</Subscript>Si<Subscript>2</Subscript>O<Subscript>5</Subscript>(OH)<Subscript>4</Subscript> hydrosilicate nanotubes by silver nitrate solutions

The interaction of an aqueous solution of silver nitrate with Mg₃Si₂O₅(OH)₄ hydrosilicate nanotubes under atmospheric conditions at 50 and 80°C and under dynamic conditions with subsequent annealing at 300°C has been investigated. The intercalation of AgNO₃ solutions into the internal channel and interlayer spaces of the nanotube structure and the crystallization of the silver particles of the spherical shapes on the nanotube surface have been established.     

Influences of phase transition and microstructure on dielectric properties of Bi<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>Zr<Subscript>1-x</Subscript>Ti<Subscript>x</Subscript>O<Subscript>3</Subscript> ceramics

Bismuth sodium zirconate titanate ceramics with the formula Bi_0.5Na_0.5Zr_1-xTi_xO₃ [BNZT], where x = 0.3, 0.4, 0.5, and 0.6, were prepared by a conventional solid-state sintering method. Phase identification was investigated using an X-ray diffraction technique. All compositions exhibited complete solubility of Ti⁴⁺ at the Zr⁴⁺ site. Both a decrease of unit cell size and phase transition from an orthorhombic Zr-rich composition to a rhombohedral crystal structure in a Ti-rich composition were observed as a result of Ti⁴⁺ substitution. These changes caused dielectric properties of BNZT ceramics to enhance. Microstructural observation carried out employing SEM showed that average grain size decreased when addition of Ti increased. Grain size difference of BNZT above 0.4 mole fraction of Ti⁴⁺ displayed a significant increase of dielectric constant at room temperature.     

Combustion synthesis of Mo<Subscript>5</Subscript>Si<Subscript>3</Subscript> in chemical furnace

The combustion synthesis of Mo₅Si₃ was carried out in a chemical furnace using 5Ti + 3Si mixtures as a chemical fuel. The synthesized single phase Mo₅Si₃ exhibited a spatial network microstructure and angular texture of crystals. The chemical composition and crystal morphology of intermediate phases suggest that the formation of Mo₅Si₃ occurs via dissolution of Mo in the Si melt followed by reactive diffusion in the supersaturated “liquid Si-Mo melt-solid Mo” system.      

Phase Equilibria in the Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> System

The phase equilibria are investigated and the phase diagram is constructed for the Gd₂O₃-SrAl₂O₄ pseudobinary join of the Gd₂O₃-SrO-Al₂O₃ ternary oxide system. One ternary compound, namely, Gd₂SrAl₂O₇, is revealed in the Gd₂O₃-SrAl₂O₄ join. It is found that this compound undergoes congruent melting.     

Phase equilibria in the Ho<Subscript>2</Subscript>O<Subscript>3</Subscript>-SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> system

The phase formation is investigated and the phase diagram of the Ho₂O₃-SrAl₂O₄ system is constructed. A ternary compound, namely, Ho₂SrAl₂O₇, is revealed. It is established that this compound undergoes incongruent melting.     

Phase Transformations in Stabilized ZrO<Subscript>2</Subscript> - Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Compositions

Data on interactions in the ZrO₂ - Fe₂O₃ system stabilized by oxides in a high-temperature form at 1750°C are obtained. Of all zirconia-based compositions, only magnesium-zirconium cubic solid solution enters into an active reaction with Fe₂O₃ to yield MgFe₂O₄. The solid solutions formed by ZrO₂ with oxides of yttrium, neodymium, and calcium resist degradation by attack from Fe₂O₃; part of iron oxide undergoes dissolution in cubic ZrO₂. __________ Translated from Novye Ogneupory, No. 9, pp. 40 – 43, September, 2005.     

Synthesis and characterization of zeolite mazzite analogue in Na<Subscript>2</Subscript>O–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–Piperazine–H<Subscript>2</Subscript>O

Zeolite Mazzite (MAZ) analogue was synthesized directly using piperazine as a structure directing agent. The reactive gel composition used was (5.0–7.0) piperazine:(6.0–7.0) Na₂O:Al₂O₃:20.0SiO₂:400H₂O. Using this composition, the reaction time was shortened greatly to 4 days and the crystallization time was reduced as well. The DTA data showed that piperazine, in as-synthesized zeolite omega decomposed easily. The decomposition of the piperazine occurred at 400–480°C. NH₃-TPD analysis proved that zeolite H-omega from piperazine had strong surface acidity with ammonia desorption temperature up to 590°C.     

Investigation of a new lead-free Bi<Subscript>0.5</Subscript>(Na<Subscript>0.40</Subscript>K<Subscript>0.10</Subscript>)TiO<Subscript>3</Subscript>-(Ba<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>)TiO<Subscript>3</Subscript> piezoelectric ceramic

Lead-free piezoelectric compositions of the (1-x)Bi_0.5(Na_0.40K_0.10)TiO₃-x(Ba_0.7Sr_0.3)TiO₃ system (when x = 0, 0.05, 0.10, 0.15, and 0.20) were fabricated using a solid-state mixed oxide method and sintered between 1,050°C and 1,175°C for 2 h. The effect of (Ba_0.7Sr_0.3)TiO₃ [BST] content on phase, microstructure, and electrical properties was investigated. The optimum sintering temperature was 1,125°C at which all compositions had densities of at least 98% of their theoretical values. X-ray diffraction patterns that showed tetragonality were increased with the increasing BST. Scanning electron micrographs showed a slight reduction of grain size when BST was added. The addition of BST was also found to improve the dielectric and piezoelectric properties of the BNKT ceramic. A large room-temperature dielectric constant, ε _r (1,609), and piezoelectric coefficient, d ₃₃ (214 pC/N), were obtained at an optimal composition of x = 0.10.     

Effect of fluorine additions on the stability of Mg<Subscript>3</Subscript>Si<Subscript>4</Subscript>O<Subscript>10</Subscript>(OH)<Subscript>2</Subscript>: Computer simulation

The computer simulation of the effect of dopant F atoms on the stability of Mg₃Si₄O₁₀(OH)₂ has been carried out using the density functional theory and pseudopotential method. It has been shown that the mechanism of dehydration is implemented by removing first hydrogen, and then (from the same OH positions) oxygen atoms. Incorporation of doped F atoms into the lattice leads to an increase in the O and H binding energies.     

Phase separation in melts of the ZrO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The morphology of the quenched and slowly crystallized samples in the ZrO₂-Al₂O₃ system is investigated in the composition range 25–70 wt % ZrO₂. It is revealed that, irrespective of the cooling rate, the samples contain large baddeleyite (or corundum) crystals, eutectic mixtures, and characteristic regions of intergrown elongated baddeleyite and corundum grains with micron sizes. These regions have the same phase composition at any initial ratio between zirconium and aluminum oxides and at any cooling rates of the melt. A hypothesis is put forward that these regions are products of the decomposition of ZrO₂ · 2Al₂O₃ associates.     

Synthetic spinels of the system MgO-Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

Synthetic spinels of the system MgO-Cr₂O₃-Al₂O₃-Fe₂O₃ are considered and the desirability of organizing their production for the refractory industry is demonstrated. Translated from Novye Ogneupory, No. 6, pp. 32–35, June 2008.     

Structure and electrical conductivity of glasses in the Na<Subscript>2</Subscript>O-Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> system

The temperature-concentration dependence of the electrical conductivity of glasses in the Na₂SO₄-NaPO₃ and Na₂O-P₂O₅ systems has been investigated. Based on the obtained experimental data (IR spectra, density, microhardness, sound velocity, and paper chromatography), it has been demonstrated that SO₄²⁻ ions form terminal groups through the incorporation into polyphosphate fragments of the structure of glasses in the Na₂SO₄-NaPO₃ system. An increase in the electrical conductivity of glasses in this system by a factor of ∼1000 (as compared to NaPO₃) at 25°C and a decrease in the activation energy for electrical conduction from 1.40 to 1.10 eV have been interpreted from the viewpoint of the decrease in the dissociation energy E _d of polar sulfate phosphate structural chemical fragments formed in the glass bulk upon introduction into sodium metaphosphate Na₂SO₄. This leads to an increase in the number of dissociated sodium ions, which are charge carriers, and to a decrease in the energy (E _a) of their activation shift in the sublattice formed by sulfate phosphate fragments of the structure.