Plasticization of nano‐CaCO3 in polystyrene/nano‐CaCO3 composites

The shear rheological properties of polystyrene (PS)/nano‐CaCO₃ composites were studied to determine the plasticization of nano‐CaCO₃ to PS. The composites were prepared by melt extrusion. A poly(styrene–butadiene–styrene) triblock copolymer (SBS), a poly(styrene–isoprene–styrene) triblock copolymer (SIS), SBS‐grafted maleic anhydride (SBS–MAH), and SIS‐grafted maleic anhydride were used as modifiers or compatibilizers. Because of the weak interaction between CaCO₃ and the PS matrix, the composites with 1 and 3 phr CaCO₃ loadings exhibited apparently higher melt shear rates under the same shear stress with respect to the matrix polymer. The storage moduli for the composites increased with low CaCO₃ concentrations. The results showed that CaCO₃ had some effects on the compatibility of PS/SBS (or SBS–MAH)/CaCO₃ composites, in which SBS could effectively retard the movement of PS chain segments. The improvement of compatibility, due to the chemical interaction between CaCO₃ and the grafted maleic anhydride, had obvious effects on the rheological behavior of the composites, the melt shear rate of the composites decreased greatly, and the results showed that nano‐CaCO₃ could plasticize the PS matrix to some extent. Rheological methods provided an indirect but useful characterization of the composite structure. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Preparation and characterization of magnetic poly(styrene–glycidyl methacrylate) microspheres for highly efficient protein adsorption by two‐stage dispersion polymerization

Micrometer‐sized superparamagnetic poly(styrene–glycidyl methacrylate)/Fe₃O₄ spheres were synthesized by two‐stage dispersion polymerization with modified hydrophobic Fe₃O₄ nanoparticles, styrene (St), and glycidyl methacrylate (GMA). The morphology and properties of the magnetic Fe₃O₄–P (St‐GMA) microspheres were examined by scanning electron microscopy, transmission electron microscopy, vibrating sample magnetometry, thermogravimetric analysis, and attenuated total reflectance. The average size of the obtained magnetic microspheres was 1.50 μm in diameter with a narrow size distribution, and the saturation magnetization of the magnetic microspheres was 8.23 emu/g. The magnetic Fe₃O₄–P (St‐GMA) microspheres with immobilized iminodiacetic acid–Cu²⁺ groups were used to investigate the adsorption capacity and selectivity of the model proteins, bovine hemoglobin (BHb) and bovine serum albumin (BSA). We found that the adsorption capacity of BHb was as high as 190.66 mg/g of microspheres, which was 3.20 times greater than that of BSA, which was only 59.64 mg/g of microspheres as determined by high‐performance liquid chromatography. With a rather low nonspecific adsorption, these microspheres have great potential for protein separation and purification applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43005.     

Interpolyelectrolyte complexes of maleic acid copolymers and chitosan for stabilization and functionalization of magnetite nano‐ and microparticles

A facile method of preparation of stabilized and functionalized nano‐ and microparticles of magnetite by successive application of oppositely charged polymers with a regular structure of macromolecular chains (chitosan and maleic acid copolymers) onto Fe₃O₄ core are developed. This approach makes it possible to create two types of magnetite interpolyelectrolyte shells, containing carboxylic or amino groups in outer layer of shell. Composition and magnetic properties of composite particles depend on nature of the copolymer of maleic acid, reaction conditions and size of obtained particles. The carboxylic groups of copolymer in outer layer of interpolyelectrolyte shell were converted into reactive anhydride groups by heating. Thermal treatment also leads to covalent crosslinking of shell and improves stability of composites both in acidic and alkaline media. Horseradish peroxidase was successfully immobilized onto covalently crosslinked and activated microparticles of Fe₃O₄ in aqueous medium without of condensing agents. The proposed reproducible and low‐cost technique does not use toxic reagents or solvents at all stages, including preparation of Fe₃O₄, formation, activation and crosslinking, of magnetite shell, modification of activated surface of composite particles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39663.     

Preparation of novel amphiphilic copolymer microspheres and their drug‐release and glucose‐sensitive properties

A novel amphiphilic copolymer was prepared by the copolymerization of N‐acryloyl‐3‐aminophenylboronic acid with β‐cyclodextrin containing maleic anhydride. The copolymer was fully characterized with ¹³C‐NMR, ¹H‐NMR, IR, and scanning electron microscopy. The self‐assembling mechanism of the copolymer in H₂O–CH₃OH cosolvents was studied. Gliclazide as a model drug was loaded inside the copolymer microspheres, and the drug‐release behavior of the microspheres was studied. The results of in vitro oscillating release tests indicated that the microspheres responded to glucose rapidly in 30 min, and the microspheres exhibited self‐regulated on–off release behavior four to six times in 6 h between the solution with 3 g/L glucose and the medium without glucose; this met the clinical requirements of multidrug delivery. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Immobilization of malto‐oligosaccharide forming α‐amylase from Bacillus subtilis KCC103: properties and application in starch hydrolysis

BACKGROUND: A malto‐oligosaccharide forming α‐amylase from Bacillus subtilis KCC103 immobilized in calcium alginate beads was repeatedly used in batch processes of starch hydrolysis. The degree of starch degradation and operational stability of the immobilized system were optimized by varying the physical characteristics and composition of the beads. The products formed from hydrolysis of various starches by α‐amylase immobilized in different supports were analyzed. RESULTS: Immobilized beads prepared from 3% (w/v) alginate and 4% (w/v) CaCl₂ were suitable for up to 10 repeated uses, losing only 25% of their efficiency. On addition of 1% silica gel to alginate prior to gelation, the operational stability of the immobilized enzyme was enhanced to 20 cycles of operation, retaining > 90% of the initial efficiency. Distribution of malto‐oligosaccharides in the starch hydrolyzate depended on the type of starch, reaction time and mode of immobilization. Soluble starch and potato starch formed a wide range of malto‐oligosaccharides (G1–G5). Starches from wheat, rice and corn formed a narrow range of smaller oligosaccharides (G1–G3) as the major products. CONCLUSION: The immobilized beads of α‐amylase from KCC103 prepared from alginate plus silica gel showed high efficiency and operational stability for hydrolysis of starch. This immobilized system is useful for production of malto‐oligosaccharides applied in the food and pharmaceutical industries. Since this KCC103 amylase can be produced at low cost utilizing agro‐residues in a short time and immobilized enzyme can be recycled, the overall cost of malto‐oligosaccharide production would be economical for industrial application. Copyright © 2008 Society of Chemical Industry     

Novel magnetic nanoparticles for the hydrolysis of starch with Bacillus licheniformis α‐amylase

Novel magnetic nanoparticles with an average size of 350–400 nm with N‐methacryloyl‐(L )‐phenylalanine (MAPA) as a hydrophobic monomer were prepared by the surfactant‐free emulsion polymerization of 2‐hydroxyethyl methacrylate, MAPA, and magnetite in an aqueous dispersion medium. MAPA was synthesized from methacryloyl chloride and L ‐phenylalanine methyl ester. The specific surface area of the nonporous magnetic nanoparticles was found to be 580 m²/g. Magnetic poly[2‐hydroxyethyl methacrylate–N‐methacryloyl‐(L )‐phenylalanine] nanoparticles were characterized by Fourier transform infrared spectroscopy, electron spin resonance, atomic force microscopy, and transmission electron microscopy. Elemental analysis of MAPA for nitrogen was estimated as 4.3 × 10^?3 mmol/g of nanoparticles. Then, magnetic nano‐poly[2‐hydroxyethyl methacrylate–N‐methacryloyl‐(L )‐phenylalanine] nanoparticles were used in the adsorption of Bacillus licheniformis α‐amylase in a batch system. With an optimized adsorption protocol, a very high loading of 705 mg of enzyme/g nanoparticles was obtained. The adsorption phenomena appeared to follow a typical Langmuir isotherm. The inverse of enzyme affinity for free amylase (181.82 mg/mL) was higher than that for immobilized enzyme (81.97 mg/mL). Storage stability was found to increase with adsorption. It was observed that the enzyme could be repeatedly adsorbed and desorbed without a significant loss in the adsorption amount or enzyme activity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Cost‐effective Synthesis of α‐LiAlO2 Powders for Molten Carbonate Fuel Cell Matrices

Lithium aluminate (α‐/β‐LiAlO₂) particles were fabricated using three methods. The first method used organic glycerin and triethylene glycol which functioned as a catalyst for fabrication of α‐LiAlO₂ particles with Al(OH)₃ and LiOH·H₂O as the starting materials. As a result of the heat‐treatment of the starting materials, α‐/β‐LiAlO₂ particles could be obtained. The amount of α‐LiAlO₂ particles in α‐/β‐LiAlO₂ increased slightly as more organics were added. Additionally, when synthesised α‐/β‐LiAlO₂ particles were heat‐treated in a CO₂ gas flow, β‐LiAlO₂ was partially transformed to α‐LiAlO₂. In the second method, molten salts (Li₂/Na₂/K₂CO₃) were used as a catalyst to fabricate α‐LiAlO₂ as a major phase, however, this method requires a washing process which can produce unexpected impurities. In the third method, pure α‐LiAlO₂ was obtained by heat‐treatment of cheap sources such as Li₂CO₃ and Al(OH)₃ at 600–800 °C. The mean particle size (604 nm–11.85 μm) and the specific surface area (3.22–11.4 m² g^–1) of α‐LiAlO₂ were suitable for reinforcing the matrix and tape casting. Lastly, this study examined the effect of CO₂ for the synthesising of α‐LiAlO₂ particles.     

Fe_3O_4/P(St-CBA)核壳磁性复合微球的制备及性质

运用分散聚合法制备出Fe3O4 /P(St -CBA)核壳磁性复合微球。该微球粒径为 0 .0 75～0 .70 0 μm、w(Fe3O4 ) =0 .0 5 %～ 0 .90 % ,呈规整球型 ,表面光滑 ,在 0 .0 5T磁场中的磁响应性为3.0cm/min。制备微球的最佳条件为 :w(磁流体 ) =0 .5 %～ 3 .0 %、w(马来酸酐 ) =0 .0 %～2 .0 %、w(无水乙醇 ) =30 .0 %～ 70 .0 %。     

Optimization of α‐amylase production in solid substrate fermentation

Response surface methodology (RSM) was used to optimize the medium components of α‐amylase production using solid substrate fermentation (SSF). Hazelnut cake (HC), peptone, yeast extract (YE), and (NH₄)₂SO₄ were selected as independent variables for optimization. Central composite design (CCD) was used in design experiments and analysis results. This procedure limited the number of actual experiments performed while allowing possible interactions between the independent variables. By using CCD, 30 experiments were performed for determining the interaction of independent variables and optimization of fermentation medium. The P‐value of the coefficient of linear effect of (NH₄)₂SO₄ concentrations, which was obtained as 0.0001 has shown that this parameter has the greatest effect on the production of α‐amylase. Model F‐value (5.62) implies that the model is significant. The highest α‐amylase activity (4895 IU) was measured when the HC, peptone, YE, and (NH₄)₂SO₄ concentrations in the medium were 22.62, 5.20, 1.62, and 6.81 g L^?1, respectively.     

Investigation on the morphological and mechanical properties of (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) ternary blends

In this work, ternary polymer blends based on (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) (SEBS) triblock copolymer and a varying concentration of the reactive (maleic anhydride)‐grafted SEBS were prepared by using a melt‐blending process. The effects of the material parameters (composition of ternary blends and SEBS/[{maleic anhydride}‐grafted SEBS] concentration ratio) and blending sequence on the morphological and mechanical properties of ternary blends were studied. Taguchi experimental design methodology was employed to design the experiments and select the material and processing parameters for the optimized mechanical properties. Tensile properties (Young's modulus and yield stress) and impact strength were considered as the response variables. It was demonstrated that there is a meaningful relationship between the composition of blends, processing parameters, observed phase structure, and obtained mechanical properties. The mechanical tests showed that the highest impact strength was achieved as the dispersion of the rubbery phase achieved an optimum size of about 1 μm. J. VINYL ADDIT. TECHNOL., 23:329–337, 2017. © 2015 Society of Plastics Engineers     

Influence of surface modification on the dispersion of nanoscale α‐Al2O3 particles in a thermoplastic polyurethane matrix

In this study, two types of nanoscale α‐Al₂O₃ particles were used for preparation of α‐Al₂O₃/thermoplastic polyurethane (TPU) composites. These α‐Al₂O₃ particles were either coated or uncoated with stearic acid. For the uncoated α‐Al₂O₃/TPU composite, the results of field‐emission scanning electron microscopy (FE‐SEM) and energy dispersive X‐ray spectrometry indicate that uncoated α‐Al₂O₃ particles are significantly aggregated together. This aggregation is due to the poor compatibility between the inorganic filler (α‐Al₂O₃) and the organic matrix (TPU). The size of clusters is in the range from 5 to 20 μm. For the coated α‐Al₂O₃/TPU composite, FE‐SEM results indicate that most coated α‐Al₂O₃ particles are well dispersed in the TPU matrix. This phenomenon results from the effect of surface modifier (i.e., stearic acid) on α‐Al₂O₃ particles. Stearic acid can act as a compatibilizer to bridge the boundary between the TPU matrix and the α‐Al₂O₃ particle. Stearic acid is not only a suitable surface modifier for the nanoscale α‐Al₂O₃ particle, but also a good dispersant for the dispersion of nanoscale α‐Al₂O₃ particles in the TPU matrix. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

α‐Amylase Modulation: Discovery of Inhibitors Using a Multi‐Pharmacophore Approach for Virtual Screening

Better control of postprandial hyperglycemia can be achieved by delaying the absorption of glucose resulting from carbohydrate digestion. Because α‐amylase initiates the hydrolysis of polysaccharides, the design of α‐amylase inhibitors can lead to the development of new treatments for metabolic disorders such as type II diabetes and obesity. In this study, a rational computer‐aided approach was developed to identify novel α‐amylase inhibitors. Three‐dimensional pharmacophores were developed based on the binding mode analysis of six different families of compounds that bind to this enzyme. In a stepwise virtual screening workflow, seven molecules were selected from a library of 1.4 million. Five out of seven biologically tested compounds showed α‐amylase inhibition, and the two most potent compounds inhibited α‐amylase with IC₅₀ values of 17 and 27 μm . The scaffold benzylideneacetohydrazide was shared by four of the discovered inhibitors, emerging as a novel drug‐like non‐carbohydrate fragment and constituting a promising lead scaffold for α‐amylase inhibition.     

Antibacterial activity of polymers with norfloxacin moieties against native and norfloxacin‐tolerance‐induced bacteria

Antimicrobial characteristics were investigated for norfloxacin against 18 bacteria (4 gram‐positive bacteria and 14 gram‐negative bacteria) with the minimum inhibition concentration (MIC) test. Among the bacteria tested, B. cereus, V. fluvialis, and V. parahaemolyticus formed norfloxacin‐tolerant colonies. The release of ultraviolet‐absorbing substances from the cells in contact with norfloxacin was examined for the native bacteria and for the norfloxacin‐tolerance‐induced ones. Norfloxacin was grafted to polypropylene‐graft‐maleic anhydride (MAPP) and poly(styrene‐co‐maleic anhydride) (MAPS) to synthesize polymeric antimicrobial agents. The bioactivity of MAPP–norfloxacin and MAPS–norfloxacin was evaluated and compared with that of neat norfloxacin with the shake flask test and the MIC test. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 936–943, 2005     

Synthesis and characterization of alkali‐modified styrene‐maleic anhydride copolymer for dispersion of TiO2

A copolymer of styrene and maleic anhydride was synthesized by free radical polymerization at 80°C using N,N‐dimethylformamide (DMF) as solvent and benzoylperoxide as initiator. The monomer feed ratio of styrene to maleic anhydride was varied in the range of 1 : 1 : to 3 : 1. The polymer yield was found to decrease with increase in styrene in the feed. The molecular weight of copolymers which were formed by taking styrene to maleic anhydride ratio of 1 : 1, 2 : 1, and 3 : 1, as determined by Ostwald Viscometery were about 1862, 2015, and 2276 respectively. The acid values of abovementioned three copolymers were found to be 480, 357, and 295, respectively. The typical viscosity values of 20% solids in ammonical solution of copolymers formed by taking feed ratios of Sty : MAn as 1 : 1 and 2 : 1 were 26 and 136 cp, respectively. For the feed ratio 3 : 1, a gel was formed. The synthesized copolymers were hydrolyzed by alkalis, namely, NaOH, KOH, and NH₄OH. The dispersing ability of hydrolyzed styrene‐maleic anhydride (SMA) copolymers for dispersion of titanium dioxide was studied. The modified SMA copolymers were found to be effective dispersants for TiO₂. Among the three alkalis studied, the Sodium salts of SMA were found to give better dispersion. The copolymer having a 1 : 1 feed ratio showed the best dispersing ability for TiO₂ particles among the three ratios studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3194–3205, 2007     

Initiation of surface graft polymerization by ceric ions on polymer microspheres

The surface graft polymerization of acrylamide on poly(styrene‐co‐acrylonitrile) copolymer microspheres by the initiation of ceric ions was studied. The grafting was verified by IR spectra and X‐ray photoelectron spectroscopy measurements. The resultant microspheres with surface‐grafted polymer chains were employed in the preparation of polymer‐microsphere‐supported palladium composite particles. The composite particles were then studied by transmission electron microscopy and X‐ray diffraction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 936–940, 2003     

Variations of the glass‐transition temperature in the imidization of poly(styrene‐co‐maleic anhydride)

The imidization of poly(styrene‐co‐maleic anhydride) (SMA) was conducted, and the glass‐transition temperatures (T_g's) of the resulting products were measured with differential scanning calorimetry. The contributions from functional groups of maleic anhydride, N‐phenylmaleamic acid, and N‐phenylmaleimide to T_g were examined. T_g increased in the order of SMA < styrene–N‐phenyl maleimide copolymer < styrene–N‐phenyl maleamic acid copolymer and followed the Fox equation. T_g of the imidized products of SMA could be controlled by the conversions of both ring‐opening and ring‐closing reactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2418–2422, 2007     

Synthesis and antitumor activity of poly(3,4‐dihydro‐2H‐pyran‐co‐maleic anhydride‐co‐vinyl acetate)

The radical‐initiated terpolymerization of 3,4‐dihydro‐2H‐pyran (DHP), maleic anhydride (MA), and vinyl acetate (VA), which were used as a donor–acceptor–donor system, was carried out in methyl ethyl ketone in the presence of 2,2′‐azobisisobutyronitrile as an initiator at 65°C in a nitrogen atmosphere. The synthesis and characterization of binary and ternary copolymers, some kinetic parameters of terpolymerization, the terpolymer‐composition/thermal‐behavior relationship, and the antitumor activity of the synthesized polymers were examined. The polymerization of the DHP–MA–VA monomer system predominantly proceeded by the alternating terpolymerization mechanism. The in vitro cytotoxicities of poly(3,4‐dihydro‐2H‐pyran‐alt‐maleic anhydride) [poly(DHP‐alt‐MA)] and poly(3,4‐dihydro‐2H‐pyran‐co‐maleic anhydride‐co‐vinyl acetate) [poly(DHP‐co‐MA‐co‐VA)] were evaluated with Raji cells (human Burkitt lymphoma cell line). The antitumor activity of the prepared anion‐active poly(DHP‐alt‐MA) and poly(DHP‐co‐MA‐co‐VA) polymers were studied with methyl–thiazol–tetrazolium testing, and the 50% cytotoxic dose was calculated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2352–2359, 2005     

Controlled preparation of Fe3O4/P (St-MA) magnetic composite microspheres by DPE method

In this work, controlled radical polymerization based on 1, 1-diphenylethylene (DPE method) was used to prepare magnetic composite microspheres. By this method, Fe₃O₄/P (St-MA) magnetic composite microspheres were prepared via copolymerization of styrene (St) and maleic anhydride (MA) using DPE as radical control agent in the presence of Fe₃O₄ nanoparticles. The structure and properties of the magnetic composite microspheres obtained were characterized by IR, ¹H-NMR, SEC-MALLS, TEM, TGA, VSM, DLS and other instruments. It was found that the DPE method allows the controlled preparation of magnetic composite microspheres, and Fe₃O₄/ P(St-MA) microspheres possess perfect sphere-shaped morphology, homogeneous particle size, carboxylic surface, superparamagnetism with a saturation magnetization of 14.704 emu/g, and magnetic content with a value of 25%.     

Preparation of hemispherical poly(4‐vinylpyridine‐co‐butyl acrylate)/poly(styrene‐co‐butyl acrylate) composite microspheres by seeded preswelling emulsion polymerization

Seeded preswelling emulsion polymerization was carried out by using monodispersed poly(4‐vinylpyridine‐co‐butyl acrylate) [P(4VP‐BA)] particles as the seed, and styrene and butyl acrylate as the second‐stage monomers under different polymerization conditions, to obtain hemispherical polystyrene (PST)‐rich–P4VP‐rich microspheres. Prior to polymerization, toluene was added into the preswelling system together with the second‐stage monomers. It was found that, with the increase of the amount of toluene, the particle morphology showed a tendency toward desirable hemispherical structure, and the colloidal stability of composite latex was improved. When the weight ratio of toluene/seed latex was increased up to 7.5/40 (g/g), the stable hemispherical latex could be obtained. However, when toluene was not added, the coagulum formed on the wall of the reactor during polymerization, and the composite particles with multiple surface domains (such as sandwich‐like, popcorn‐like) were formed. In addition, the final morphology of composite particles was influenced by the polarity of the seed crosslinker and the hydrophilicity of the second‐stage initiator, which could affect the mobility of poly(styrene‐co‐butyl acrylate) [P(ST‐BA)] chains. The morphology development during the polymerization was investigated in detail, and a schematic model was derived to depict the formation mechanism of hemispherical P(4VP‐BA)/P(ST‐BA) composite microspheres. The results revealed that the mobility of the P(ST‐BA) chains influenced the diffusion of the P(ST‐BA) domains on the surface of the P(4VP‐BA) matrix. When the mobility of the P(ST‐BA) chains allowed small‐size P(ST‐BA) domains to coalesce into one larger domain, complete phase‐separated morphology (hemisphere) could be achieved. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3811–3821, 2003     

Use of modified poly(ϵ‐caprolactone) in the compatibilization of poly(ϵ‐caprolactone)/maize starch blends

In this work, the compatibilization of a poly(?‐caprolactone) with a number‐average molecular weight of 120,000 g/mol (PCL¹²⁰) and maize starch was investigated by the addition of a chemically modified poly(?‐caprolactone). Two types of blends were prepared by melt extrusion. In type A blends, low‐molecular‐weight compatibilizers were used: (1) a poly(?‐caprolactone) with a number‐average molecular weight of 10,000 g/mol that was reacted with maleic anhydride to obtain chains terminating in carboxylic groups and (2) low‐molecular‐weight poly(?‐caprolactone)s (number‐average molecular weights of 600 and 2000 g/mol) with one pendant carboxylic group within the chains. With these groups of blends, tensile testing and scanning electron microscopy demonstrated that the compatibilizers were generally effective in inducing a better dispersion for a 60/40 poly(?‐caprolactone)/maize starch blend with a compatibilizer, improving the mechanical properties in comparison with uncompatibilized blends. The blends with 30% starch were not improved by the addition of compatibilizer, and this may be related to the rheology of the blends during preparation. In type B blends, high‐molecular‐weight compatibilizers were prepared through the grafting of variable amounts of acrylic acid or maleic anhydride to PCL¹²⁰ chains. The best compatibilizer action was obtained with 0.7 wt % maleic anhydride grafted to PCL¹²⁰ because both the dispersion and mechanical properties were further improved in comparison with uncompatibilized blends and type A blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008