Three‐Dimensionally Ordered Macroporous Polymeric Materials by Colloidal Crystal Templating for Reversible CO2 Capture

The design and preparation of porous materials with controlled structures and functionalities is crucial to a variety of absorption‐ or separation‐relevant applications, including CO₂ capture. Here, novel functional polymeric materials with three‐dimensionally ordered macroporous (3DOM) structures are prepared by using colloidal crystals as templates using relatively simple, rapid, and inexpensive approaches. These ordered structures are used for the reversible CO₂ capture from ambient air by humidity swing. Typically, the colloidal crystal template is synthesized from polymer latex particles of poly(methyl methacrylate) (PMMA) or polystyrene (PS). To maintain the functionality of the material, it is important to prevent the porous structure collapsing, which can occur by the hydrolysis of the ester bonds in conventional crosslinkers under basic conditions. This hydrolysis can be prevented by using a water‐soluble crosslinker containing two quaternary ammonium moieties, which can be used to prepare stable porous crosslinked polymers with the monomer (vinylbenzyl)trimethylammonium chloride (VBTMACl) and using a PMMA‐based colloidal crystal template. The hydroxide‐containing monomer and dicationic crosslinker are synthesized from their chloride precursors, avoiding the ion‐exchange step which causes shrinkage of the pores. An analysis of different methods for infiltrating the monomer solution into the colloidal crystal template shows that infiltration using capillary forces leads to fewer defects than infiltration under a partial vacuum. In addition, functional macroporous films with micrometer thickness are prepared from a template of PS‐based colloidal crystals in a thin film. In general, the colloidal crystal templated materials showed improved CO₂ absorption/desorption rates and swing sizes compared to a commercially available material with similar functional groups. This work could easily be extended to create a new generation of ordered macroporous polymeric materials with tunable functionalities for other applications.     

Think Positive: Phase Separation Enables a Positively Charged Additive to Induce Dramatic Changes in Calcium Carbonate Morphology

Soluble macromolecules are essential to Nature's control over biomineral formation. Following early studies where macromolecules rich in aspartic and glutamic acid were extracted from nacre, research has focused on the use of negatively charged additives to control calcium carbonate precipitation. It is demonstrated that the positively charged additive poly(allylamine hydrochloride) (PAH) can also cause dramatic changes in calcite morphologies, yielding thin films and fibers of CaCO₃ analogous to those produced with poly(aspartic acid) via a so‐called PILP (polymer‐induced liquid precursor) phase. The mechanism by which PAH induces these effects is investigated using a range of techniques including cryo transmission electron microscopy (TEM), Raman microscopy, and thermogravimetric analysis, and the data show that hydrated Ca²⁺/PAH/CO₃^2? droplets initially form in solution, before coalescing and ultimately crystallizing to give calcite, together with small quantities of vaterite. It is suggested that it is the initial formation of hydrated Ca²⁺/PAH/CO₃^2? droplets that is key to this process, rather than a specific polymer/mineral interaction. These results are discussed in terms of their relevance to biomineralization processes and highlight the opportunity for using counter‐ion‐induced phase separation of polyelectrolytes as a method for generating minerals with non‐crystallographic morphologies.     

Polyphenylene Dendrimer‐Templated In Situ Construction of Inorganic–Organic Hybrid Rice‐Shaped Architectures

A novel dendrimer‐templating method for the synthesis of CuO nanoparticles and the in situ construction of ordered inorganic–organic CuO–G2Td(COOH)₁₆rice‐shaped architectures (RSAs) with analogous monocrystalline structures are reported. The primary CuO nanoparticles are linked by the G2Td(COOH)₁₆ dendrimer. This method provides a way to preserve the original properties of primary CuO nanoparticles in the ordered hybrid nanomaterials by using the 3D rigid polyphenylene dendrimer (G2Td(COOH)₁₆) as a space isolation. The primary CuO nanoparticles with diameter of (6.3 ± 0.4) nm are synthesized via four successive reaction steps starting from the rapid reduction of Cu(NO₃)₂ by using NaBH₄ as reducer and G2Td(COOH)₁₆ as surfactant. The obtained hybrid CuO–G2Td(COOH)₁₆ RSA, formed in the last reaction step, possesses a crystal structure analogous to a monocrystal as observed by transmission electron microscopy(TEM). In particular, the formation process of the RSA is monitored by UV–vis, TEM, and X‐ray diffraction. Small angle X‐ray scattering and Fourier transform infrared spectroscopy are used to investigate the role of the dendrimer in the RSA formation process. The obtained results illuminate that Cu²⁺? COO^? coordination bonds play an indispensable role in bridging and dispersing the primary CuO nanoparticles to induce and maintain the hybrid RSA. More importantly, the RSA is retained through the Cu²⁺? COO^?coordination bonds even with HCl treatment, suggesting that the dendrimers and Cu²⁺ ions may form rice‐shaped polymeric complexes which could template the assembly of CuO nanoparticles towards RSAs. This study highlights the feasibility and flexibility of employing the peculiar dendrimers to in‐situ build up hybrid architectures which could further serve as templates, containers or nanoreactors for the synthesis of other nanomaterials.     

Intracellularly Degradable Hydrogen‐Bonded Polymer Capsules

The assembly of low‐fouling polymer capsules with redox‐responsive behavior and intracellular degradability is reported. Thiol‐containing poly(2‐ethyl‐2‐oxazoline) (PEtOxMA_SH) brushes are synthesized by atom transfer radical polymerization (ATRP) of oligo(2‐ethyl‐2‐oxazoline)methacrylate and glycidyl methacrylate (GMA) and subsequent ring‐opening reaction of the GMA. Sequential deposition of PEtOxMA_SH/poly(methacrylic acid) (PMA) multilayers onto silica (SiO₂) particle templates and crosslinking through disulfide formation yield stable capsules after the removal of the SiO₂ templates by buffered hydrofluoric acid (HF). The redox‐responsive nature of the disulfide crosslinking groups enables the degradation of these capsules under simulated intracellular conditions at pH 5.9 and 5 mm glutathione (GSH). Furthermore, capsule degradation is observed after incubation with dendritic (JAWS II) cells. Even at high capsule‐to‐cell ratios, PEtOxMA_SH capsules show only negligible cytotoxicity. Quartz crystal microgravimetry (QCM) studies, using 100% human serum, reveal that films prepared from PEtOxMA_SH exhibit low‐fouling properties. The degradation and low‐fouling properties are promising for application of PEtOxMA_SH films/capsules for the delivery and triggered release of therapeutics.     

Amphiphilic Poly(p‐phenylene)s for Self‐Organized Porous Blue‐Light‐Emitting Thin Films

Micro‐ and nanostructuring of conjugated polymers are of critical importance in the fabrication of molecular electronic devices as well as photonic and bandgap materials. The present report delineates the single‐step self‐organization of highly ordered structures of functionalized poly(p‐phenylene)s without the aid of either a controlled environment or expensive fabrication methodologies. Microporous films of these polymers, with a honeycomb pattern, were prepared by direct spreading of the dilute polymer solution on various substrates, such as glass, quartz, silicon wafer, indium tin oxide, gold‐coated mica, and water, under ambient conditions. The polymeric film obtained from C₁₂PPPOH comprises highly periodic, defect‐free structures with blue‐light‐emitting properties. It is expected that such microstructured, conjugated polymeric films will have interesting applications in photonic and optoelectronic devices. The ability of the polymer to template the facile micropatterning of nanomaterials gives rise to hybrid films with very good spatial dispersion of the carbon nanotubes.     

Biofunctional Polyelectrolyte Multilayers and Microcapsules: Control of Non‐Specific and Bio‐Specific Protein Adsorption

Layers of the polyelectrolytes poly(allylamine hydrochloride) (PAH, polycationic) and poly(styrene sulfonate) (PSS, polyanionic) are consecutively adsorbed on flat silicon oxide surfaces, forming stable, ultrathin multilayer films. Subsequently, a final monolayer of the polycationic copolymer poly(L ‐lysine)‐graft‐poly(ethylene glycol) (PLL‐g‐PEG) is adsorbed onto the PSS‐terminated multilayer in order to impart protein resistance to the surface. The growth of each of the polyelectrolyte layers and the protein resistance of the resulting [PAH/PPS]_n(PLL‐g‐PEG) multilayer (n = 1–4) are followed quantitatively ex situ using X‐ray photoelectron spectroscopy and in situ using real‐time optical‐waveguide lightmode spectroscopy. In a second approach, the same type of [PAH/PSS]_n(PLL‐g‐PEG) multilayer coatings are successfully formed on the surface of colloidal particles in order to produce surface‐functionalized, hollow microcapsules after dissolution of the core materials (melamine formaldehyde (MF) and poly(lactic acid) (PLA; colloid diameters: 1.2–20 μm). Microelectrophoresis and confocal laser scanning microscopy are used to study multilayer formation on the colloids and protein resistance of the final capsule. The quality of the PLL‐g‐PEG layer on the microcapsules depends on both the type of core material and the dissolution protocols used. The greatest protein resistance is achieved using PLA cores and coating the polyelectrolyte microcapsules with PLL‐g‐PEG after dissolution of the cores. Protein adsorption from full serum on [PAH/PPS]_n(PLL‐g‐PEG) multilayers (on both flat substrates and microcapsules) decreases by three orders of magnitude in comparison to the standard [PAH/PPS]_n layer. Finally, biofunctional capsules of the type [PAH/PPS]_n(PLL‐g‐PEG/PEG‐biotin) (top copolymer layer with a fraction of the PEG chains end‐functionalized with biotin) are produced which allow for specific recognition and immobilization of controlled amounts of streptavidin at the surface of the capsules. Biofunctional multilayer films and capsules are believed to have a potential for future applications as novel platforms for biotechnological applications such as biosensors and carriers for targeted drug delivery.     

The Control of Shrinkage and Thermal Instability in SU‐8 Photoresists for Holographic Lithography

The negative‐tone epoxy photoresist, SU‐8, expands ≈1% by volume after postexposure baking. However, if the maximum optical fluence is comparable to that at the insolubility threshold, as in a holographic exposure, the developed resist shrinks (≈35% by volume) due to the removal of light oligomers not incorporated into the polymeric network. IR spectroscopy shows that, at this level of exposure, only 15% of the epoxy groups in the insoluble polymer have reacted; consequently microstructural elements soften and collapse at >100 °C. When the light oligomers are removed, the sensitivity of the resist is unchanged, provided that 5% (w/w) of a high‐molecular‐weight reactive plasticizer (glycidoxy‐terminated polyethylene glycol) is added, but it shrinks less on development and, when used as a photonic crystal template, shows improved uniformity with less cracking and buckling. Reinforcing the polymer network by reaction with the polyfunctional amine (bis‐N,N′‐(3‐aminopropyl)ethylenediamine) increases the extent of cross‐linking and the thermal stability, allowing inverse replicas of photonic crystal templates to be fabricated from both Al:ZnO and Zr₃N₄ using atomic layer deposition at temperatures up to 200 °C.     

Copper‐Assisted Weak Polyelectrolyte Multilayer Formation on Microspheres and Subsequent Film Crosslinking

The formation of weak polyelectrolyte films on planar and spherical supports has recently evoked major interest, as such coatings allow novel material properties to be tunable by pH and salt adjustment of the polyelectrolyte deposition conditions. We report on the build up of multilayers of the weak polyelectrolytes poly(acrylic acid) (PAA) and poly(allylamine hydrochloride) (PAH) on submicrometer‐sized polystyrene (PS) and silica colloid spheres (～ 500 nm) with the aid of copper ion templating. The copper ions complex to the carboxylate groups of PAA, facilitating the formation of PAA/PAH multilayers on the particles. Regular growth of the layers on the colloid spheres with each polyelectrolyte deposition step was confirmed by microelectrophoresis, single‐particle light scattering (SPLS), and transmission electron microscopy (TEM), with an average bilayer thickness of ～ 3 nm. The polyelectrolyte multilayer‐coated particles formed stable colloidal dispersions, with ζ‐potentials ranging from 30 mV (PAH outer layer) and –50 mV (PAA outer layer). Complementary quartz‐crystal microbalance and UV‐vis spectrophotometry studies on PAA/PAH multilayers formed on planar supports were performed to examine the film formation and the role of copper ion binding to the layers. PAA/PAH multilayers formed on colloid particles were also chemically crosslinked by using the activator 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide (EDC). The degree of film crosslinking could be readily controlled by varying the concentration of EDC employed. Following solvent decomposition of the template particles coated with crosslinked PAA/PAH multilayers, intact hollow polymer capsules were obtained. These capsules were found to be impenetrable to polystyrene.     

Flexible and Robust 2D Arrays of Silver Nanowires Encapsulated within Freestanding Layer‐by‐Layer Films

Freestanding layer‐by‐layer (LbL) films encapsulating controlled volume fractions (? = 2.5–22.5 %) of silver nanowires are fabricated. The silver nanowires are sandwiched between poly(allylamine hydrochloride)/poly(styrene sulfonate) (PAH/PSS) films resulting in nanocomposite structures with a general formula of (PAH/PSS)₁₀PAH Ag(PAH/PSS)₁₀PAH. The Young's modulus, toughness, ultimate stress, and ultimate strain are evaluated for supported and freestanding structures. Since the diameter of the nanowires (73 nm) is larger than the thickness of the LbL films (total of about 50 nm), a peculiar morphology is observed with the silver nanowires protruding from the planar LbL films. Nanowire‐containing LbL films possess the ability to sustain significant elastic deformations with the ultimate strain reaching 1.8 %. The Young's modulus increases with increasing nanowire content, reaching about 6 GPa for the highest volume fraction, due to the filler reinforcement effect commonly observed in composite materials. The ultimate strengths of these composites range from 60–80 MPa and their toughness reaches 1000 kJ m^–3 at intermediate nanowire content, which is comparable to LbL films reinforced with carbon nanotubes. These robust freestanding 2D arrays of silver nanowires with peculiar optical, mechanical, and conducting properties combined with excellent micromechanical stability could serve as active elements in microscopic acoustic, pressure, and photothermal sensors.     

Mesoporous Protein Particles Through Colloidal CaCO3 Templates

Porous colloidal particles can be tailored using templating techniques to maximize their effectiveness for a wide range of applications, including separation, catalysis, and drug delivery. However, templating usually involves harsh and complex preparation conditions, thereby complicating the fabrication of sensitive bio‐functionalized particles. Here a simple, yet versatile and mild approach us used to create porous protein particles using mesoporous CaCO₃ colloids as sacrificial templates. The three‐step preparation procedure involves infiltrating the colloidal templates with the protein by solvent evaporation, protein crosslinking, and removal of CaCO₃. Using this method one can obtain porous particles consisting of virtually any protein. To explore the applicability of the particles for various scenarios particles composed of different proteins are fabricated focusing on hemoglobin and trypsin and particle morphology, porosity, mechanical properties, the protein redox state, and enzymatic activity are determined. The results show that the nanoporous template structure is replicated and that the proteins are fully functional. By varying preparation conditions such as crosslinker concentration and protein content the elastic modulus is adjusted in the range of red blood cells. This ensures high deformability upon flow in microchannels and makes the porous protein particles a versatile platform for biomedical applications.     

Polymorph Switching of Calcium Carbonate Crystals by Polymer‐Controlled Crystallization

Polymer‐controlled crystallization of calcium carbonate crystals in solution by a gas diffusion method has been carried out in the presence of poly(sodium 4‐styrene sulfonate‐co‐N‐isopropylacrylamide) (PSS‐co‐PNIPAAM), and for the first time all three anhydrous polymorphs, calcite, vaterite, and aragonite could be selectively produced with a single additive. The selective polymorph synthesis can be nicely adjusted simply by concentration variations of polymer and calcium ions in the present reaction system. The simplicity of the system reveals the influence of Ca²⁺ and polymer concentration on the nucleation and crystal growth of CaCO₃ via the balance between thermodynamic and kinetic reaction control. A single mechanistic framework employing particle mediated as well as ion mediated crystallization for polymorph control is proposed.     

Highly Organized Mesoporous TiO2 Films with Controlled Crystallinity: A Li‐Insertion Study

A study of electrochemical Li insertion combined with structural and textural analysis enabled the identification and quantification of individual crystalline and amorphous phases in mesoporous TiO₂ films prepared by the evaporation‐induced self‐assembly procedure. It was found that the properties of the amphiphilic block copolymers used as templates, namely those of a novel poly(ethylene‐co‐butylene)‐b‐poly(ethylene oxide) polymer (KLE) and commercial Pluronic P123 (HO(CH₂CH₂O)₂₀(CH₂CH(CH₃)O)₇₀(CH₂CH₂O)₂₀H), decisively influence the physicochemical properties of the resulting films. The KLE‐templated films possess a 3D cubic mesoporous structure and are practically amorphous when calcined at temperatures below 450 °C, but treatment at 550–700 °C provides a pure‐phase (anatase), fully crystalline material with intact mesoporous architecture. The electrochemically determined fraction of crystalline anatase increases from 85 to 100 % for films calcined at 550 and 700 °C, respectively. In contrast, the films prepared using Pluronic P123, which also show a 3D cubic pore arrangement, exhibit almost 50 % crystallinity even at a calcination temperature of 400 °C, and their transformation into a fully crystalline material is accompanied by collapse of the mesoporous texture. Therefore, our study revealed the significance of using suitable block‐copolymer templates for the generation of mesoporous metal oxide films. Coupling of both electrochemical and X‐ray diffraction methods has shown to be highly advisable for the correct interpretation of structure properties, in particular the crystallinity, of such sol–gel derived films.     

Amorphous Calcium Carbonate is Stabilized in Confinement

Biominerals typically form within localized volumes, affording organisms great control over the mineralization process. The influence of such confinement on crystallization is studied here by precipitating CaCO₃ within the confines of an annular wedge, formed around the contact point of two crossed half‐cylinders. The cylinders are functionalized with self‐assembled monolayers of mercaptohexadecanoic acid on gold. This configuration enables a systematic study of the effects of confinement since the surface separation increases continuously from zero at the contact point to macroscopic (mm) separations. While oriented rhombohedral calcite crystals form at large (>10 µm) separations, particles with irregular morphologies and partial crystallinity are observed as the surface separation approaches the dimensions of the unconfined crystals (5–10 µm). Further increase in the confinement has a significant effect on the crystallization process with flattened amorphous CaCO₃ (ACC) particles being formed at micrometer separations. These ACC particles show remarkable stability when maintained within the wedge but rapidly crystallize on separation of the cylinders. A comparison of bulk and surface free‐energy terms shows that ACC cannot be thermodynamically stable at these large separations, and the stability is attributed to kinetic factors. This study therefore shows that the environment in which minerals form can have a significant effect on their stability and demonstrates that ACC can be stabilized with respect to the crystalline polymorphs of CaCO₃ by confinement alone. That ACC was stabilized at such large (micrometer) separations is striking, and demonstrates the versatility of this strategy, and its potential value in biological systems.     

One‐Step Formulation of Protein Microparticles with Tailored Properties: Hard Templating at Soft Conditions

Formulation of therapeutic proteins into particulate forms is a main strategy for site‐specific and prolonged protein delivery as well as for protection against degradation. Precise control over protein particle size, dispersity, purity, as well as mild preparation conditions and minimal processing steps are highly desirable. It is, however, hard to fit all these criteria with conventional preparation techniques. Here a one‐step hard‐templating synthesis of microparticles composed of functional, non‐denatured protein is reported. The method is based on filling porous CaCO₃ microtemplates with the protein near to its isoelectric point (pI) followed by pH‐ or EDTA‐mediated dissolution of the tempplates. In principle, a wide variety of proteins can be converted into microparticles using this approach. The main requirement is an overlap of the protein insolubility and a template solubility for a certain parameter (here pH or EDTA). Here the formulation of insulin particles is studied in detail and it is shown that particles consisting of high molecular weight protein (catalase) can also be prepared. In this context, the synthesis of CaCO₃ templates with controlled size, the mechanism of the protein microparticle formation and mechanical properties of the microparticles are discussed. For the first time, the fabrication of mesoporous monodispersed CaCO₃ microtemplates with identical porocity but tuned diameter from 3 to 20 μm is demonstrated. The protein particle diameter can be adjusted by choosing the appropriate template size that is critical for successful pulmonary delivery of insulin. As a first step towards insulin delivery, the in vitro release of insulin at physiological conditions is studied.     

Layer‐by‐Layer Controlled Perovskite Nanocomposite Thin Films for Piezoelectric Nanogenerators

Perovskite nanoparticle‐based nanocomposite thin films strictly tailored using unconventional layer‐by‐layer (LbL) assembly in organic media for piezoelectric nanogenerators (NGs) are demonstrated. By employing sub‐20‐nm BaTiO₃ nanoparticles stabilized by oleic acid ligands (i.e., OA‐BTO_NPs) and carboxylic acid (COOH)‐functionalized polymers, such as poly(acrylic acid) (PAA), the resulting OA‐BTO_NP/PAA nanocomposite multilayers are prepared by exploiting the high affinity between the COOH groups of PAA and the BTO_NPs. The ferroelectric and piezoelectric performance of the (PAA/OA‐BTO_NP)_n thin films can be precisely controlled by altering the bilayer number, inserted polymer type, and OA‐BTO_NP size. It is found that the LbL assembly in nonpolar solvent media can effectively increase the quantity of adsorbed OA‐BTO_NPs, resulting in the dramatic enhancement of electric power output from the piezoelectric NGs. Furthermore, very low leakage currents are detected from the (PAA/OA‐BTO_NP)_n thin films for obtaining highly reliable power‐generating performance of piezoelectric NGs.     

From Fragility to Flexibility: Construction of Hydrogel Bridges toward a Flexible Multifunctional Free‐Standing CaCO3 Film

Free‐standing CaCO₃ materials are an important member in biological systems because of their existence in many natural organisms such as nacre, shell, and crustacean cuticle. However, toughness of those artificial mineral films is sacrificed once their inorganic content is up to 90%, thus free‐standing characteristics have seldom been achieved for CaCO₃ films, let alone their real applications. Herein a fast and simple method for constructing hydrogel “bridges” for CaCO₃ microparticles is presented, developing highly flexible free‐standing CaCO₃ films with only 5% organic content. Such integrated films have underwater superoleophobicity and self‐cleaning function, which guarantee their repeated application in oil/water separation. Furthermore, heavy metal ions can be efficiently removed by simple filtration with the films. Because of the self‐similar structure, the films are able to resist mechanical abrasion without losing the anti‐wetting property and separation efficiency. The free‐standing CaCO₃ films are put forward for the first time to practical application, demonstrating the strategy can bring a brilliant prospect to artificial biomineral materials.     

Light‐Emitting Rubrene Nanowire Arrays: A Comparison with Rubrene Single Crystals

This is a report on a new method of growth of a light‐emitting rubrene nanowires array with diameters of 200 ± 10 nm by using organic vapor transport through Al₂O₃ nanoporous templates. Nanometer‐scale laser confocal microscope (LCM) photoluminescence (PL) spectra and crystalline structures of the rubrene nanowires are compared with those of rubrene single crystals prepared with the same experimental conditions without the template. In the LCM PL spectra it is observed that the PL spectra and intensity varies with the detecting positions because of the crystal growth characteristics of the rubrene molecules. A single rubrene nanowire has a wider LCM PL band width than that of the rubrene single crystal. This may originate from the light emissions of the mixed polarized bands due to additional new crystallinity in the formation of the nanowires. From the current–voltage characteristic curves, the semiconducting nature of both the rubrene nanowires and single crystals is observed.     

Macroscopic Nanotemplating of Semiconductor Films with Hydrogen‐Bonded Lyotropic Liquid Crystals

Aqueous gel‐like lyotropic liquid crystals with extensive hydrogen bonding and nanoscale hydrophilic compartments have been used to define the growth of macroscopic nanotemplated CdS and CdTe thin films. These mesoporous semiconductor films contain a hexagonal array of 2.5 nm pores, 7 nm center‐to‐center, that extend in an aligned fashion perpendicular to the substrate. The CdS is deposited on a polypropylene substrate by a reaction between Cd(NO₃)₂ dissolved in the liquid crystal and H₂S transported via diffusion through the substrate. The CdTe is electrodeposited on indium‐tin‐oxide‐coated glass from TeO₂ and Cd(NO₃)₂, both of which are dissolved in the liquid‐crystal template. The porous nature of the CdTe films enables chemical transformations of the entire bulk of the film. As electrodeposited, the CdTe films are Te rich and, in contrast to a non‐templated film, the excess Te could be removed via a chemical treatment, proving the continuity of the pores in the nanotemplated films. These results suggest that liquid‐crystal lithography with hydrogen‐bonding amphiphiles may be a useful approach to create materials with nanoscale features over macroscopic dimensions.     

Enhanced Electrochromism with Rapid Growth Layer‐by‐Layer Assembly of Polyelectrolyte Complexes

In this work, a facile method to deposit fast growing electrochromic multilayer films with enhanced electrochemical properties using layer‐by‐layer (LbL) self‐assembly of complex polyelectrolyte is demonstrated. Two linear polymers, poly(acrylic acid) (PAA) and polyethylenimine (PEI), are used to formulate stable complexes under specific pH to prepare polyaniline (PANI)/PAA‐PEI multilayer films via LbL deposition. By introducing polymeric complexes as building blocks, [PANI/PAA‐PEI]_n films grow much faster compared with [PANI/PAA]_n films, which are deposited under the same condition. Unlike the compact [PANI/PAA]_n films, [PANI/PAA‐PEI]_n films exhibit porous structure that is beneficial to the electrochemical process and leads to improved electrochromic properties. An enhanced optical modulation of 30% is achieved with [PANI/PAA‐PEI]₃₀ films at 630 nm compared with the lower optical modulation of 11% measured from [PANI/PAA]₃₀ films. The switching time of [PANI/PAA‐PEI]₃₀ films is only half of that of [PANI/PAA]₃₀ films, which indicates a faster redox process. Utilizing polyelectrolyte complexes as building blocks is a promising approach to prepare fast growing LbL films for high performance electrochemical device applications.     

Hybrid Templated Synthesis of Crack‐Free,Organized Mesoporous TiO2 Electrodes for High Efficiency Solid‐State Dye‐Sensitized Solar Cells

Organic/inorganic hybrid templates, i.e., aluminium oxide (Al₂O₃) nanoparticles grafted with poly(oxyethylene) methacrylate, Al₂O₃‐POEM, are synthesized via surface‐initiated atom transfer radical polymerization (ATRP), as confirmed by Fourier transform‐infrared spectroscopy (FT‐IR) and thermogravimetric analysis (TGA). Upon combining the Al₂O₃‐POEM with titanium(IV) isopropoxide (TTIP), hydrophilic TTIP is selectively confined in the hydrophilic POEM chains through hydrogen bonding interactions. Following the calcination at 450 °C and the selective etching of Al₂O₃ with NaOH, the OM‐TiO₂ films with high surface areas, good interconnectivity, and anatase phase are obtained. The solid‐state dye‐sensitized solar cells (ssDSSCs) fabricated with OM‐TiO₂ photoelectrodes and a polymerized ionic liquid (PIL) show a high energy conversion efficiency of 7.3% at 100 mW cm^?2, which is one of the highest values for ssDSSCs. The high cell performance is due to the well‐organized structure, resulting in improved dye loading, excellent pore filling of electrolyte, enhanced light harvesting, and reduced charge recombination.