High‐Performance Solution‐Processable Poly(p‐phenylene vinylene)s for Air‐Stable Organic Field‐Effect Transistors

The influence of the substitution pattern (unsymmetrical or symmetrical), the nature of the side chain (linear or branched), and the processing of several solution processable alkoxy‐substituted poly(p‐phenylene vinylene)s (PPVs) on the charge‐carrier mobility in organic field‐effect transistors (OFETs) is investigated. We have found the highest mobilities in a class of symmetrically substituted PPVs with linear alkyl chains (e.g., R¹, R² = n‐C₁₁H₂₃, R³ = n‐C₁₈H₃₇). We have shown that the mobility of these PPVs can be improved significantly up to values of 10^–2 cm² V^–1 s^–1 by annealing at 110 °C. In addition, these devices display an excellent stability in air and dark conditions. No change in the electrical performance is observed, even after storage for thirty days in humid air.     

Ambipolar Charge Transport in Air‐Stable Polymer Blend Thin‐Film Transistors

Ambipolar thin‐film transistors based on a series of air‐stable, solution‐processed blends of an n‐type polymer poly(benzobisimidazobenzophenanthroline) (BBL) and a p‐type small molecule, copper phthalocyanine (CuPc) are demonstrated, where all fabrication and measurements are performed under ambient conditions. The hole mobilities are in the range of 6.0 × 10^–6 to 2.0 × 10^–4 cm² V^–1 s^–1 and electron mobilities are in the range of 2.0 × 10^–6 to 3.0 × 10^–5 cm² V^–1 s^–1, depending on the blend composition. UV‐vis spectroscopy and electron diffraction show crystallization of CuPc in the metastable α‐crystal form within the semicrystalline BBL matrix. These CuPc domains develop into elongated ribbon‐like crystalline nanostructures when the blend films are processed in methanol, but not when they are processed in water. On methylene chloride vapor annealing of the blend films, a phase transformation of CuPc from the α‐form to the β‐form is observed, as shown by optical absorption spectroscopy and electron diffraction. Ambipolar charge transport is only observed in the blend films where CuPc crystallized in the elongated ribbon‐like nanostructures (α‐form). Ambipolar behavior is not observed with CuPc in the β‐polymorph. Unipolar hole mobilities as high as 2.0 × 10^–3 cm² V^–1 s^–1 are observed in these solution‐processed blend field‐effect transistors (FETs) on prolonged treatment in methanol, comparable to previously reported hole mobilities in thermally evaporated CuPc FETs. These results show that ambipolar charge transport and carrier mobilities in multicomponent organic semiconductors are intricately related to the phase‐separated nanoscale and crystalline morphology.     

2,7‐Carbazolenevinylene‐Based Oligomer Thin‐Film Transistors: High Mobility Through Structural Ordering

We have fabricated organic field‐effect transistors based on thin films of 2,7‐carbazole oligomeric semiconductors 1,4‐bis(vinylene‐(N‐hexyl‐2‐carbazole))phenylene (CPC), 1,4‐bis(vinylene‐(N′‐methyl‐7′‐hexyl‐2′‐carbazole))benzene (RCPCR), N‐hexyl‐2,7‐bis(vinylene‐(N‐hexyl‐2‐carbazole))carbazole (CCC), and N‐methyl‐2,7‐bis(vinylene‐(7‐hexyl‐N‐methyl‐2‐carbazole))carbazole (RCCCR). The organic semiconductors are deposited by thermal evaporation on bare and chemically modified silicon dioxide surfaces (SiO₂/Si) held at different temperatures varying from 25 to 200 °C during deposition. The resulting thin films have been characterized using UV‐vis and Fourier‐transform infrared spectroscopies, scanning electron microscopy, and X‐ray diffraction, and the observed top‐contact transistor performances have been correlated with thin‐film properties. We found that these new π‐conjugated oligomers can form highly ordered structures and reach high hole mobilities. Devices using CPC as the active semiconductor have exhibited mobilities as high as 0.3 cm² V^–1 s^–1 with on/off current ratios of up to 10⁷. These features make CPC and 2,7‐carbazolenevinylene‐based oligomers attractive candidates for device applications.     

Oligothiophene‐Functionalized Truxene: Star‐Shaped Compounds for Organic Field‐Effect Transistors

Organic field‐effect transistors (OFETs) based on oligothiophene‐functionalized truxene derivatives have been fabricated for use as novel star‐shaped organic semiconductors in solution‐processible organic electronics. The electronic and optical properties of compounds 1 – 3 , with increasing numbers of thiophene rings at each of the three branches, have been investigated using scanning electron microscopy (SEM), X‐ray diffraction measurements, and ultraviolet–visible (UV‐vis) and photoluminescence spectroscopies. The results show that with a stepwise increase of the thiophene rings at every branch, a transition from a polycrystalline to an amorphous state is observed. The characteristics of compounds 1 , 2 , and 3 used for OFETs exhibit a significant difference. The mobility depends greatly on the morphology in the solid state, and decreases in going from 1 to 3 . Mobilities up to 1.03 × 10^–3 cm² V^–1 s^–1 and an on/off ratio of about 10³ for compound 1 have been achieved; these are the highest values for star‐shaped organic semiconductors used for OFETs so far. All the results demonstrate that the truxene core of the oligothiophene‐functionalized truxene derivatives not only extends the π‐delocalized system, but also leads to high mobilities for the compounds.     

Morphology and Field‐Effect‐Transistor Mobility in Tetracene Thin Films

The growth of vacuum‐sublimed tetracene thin films on silicon dioxide has been investigated from the early stages of the process. The effects of deposition flux and substrate silanization on film morphology and electrical properties have been explored. Tetracene shows an island growth, resulting in films with a granular structure. Both an increase in the deposition flux and the substrate silanization determine a decrease of the grain size and an improvement of the connectivity of the film in direct contact with the substrate. The hole mobility in field‐effect transistors based on tetracene thin films, which also generate electroluminescence, increases with the deposition flux and values as high as 0.15 cm² V^–1 s^–1 are obtained.     

Enhancement of Interconnectivity in the Channels of Pentacene Thin‐Film Transistors and Its Effect on Field‐Effect Mobility

With the aim of improving the field‐effect mobility of transistors by promoting the interconnectivity of the grains in pentacene thin films, deposition conditions of the pentacene molecules using one‐step (total thickness of layer 50 nm: 0.1 Å s^–1) and two‐step (first layer 10 nm: 0.1 Å s^–1, second layer 40 nm: 4.0 Å s^–1) depositions are controlled. Significantly, it is found that the continuities of the pentacene thin films vary with the deposition conditions of the pentacene molecules. Specifically, a smaller number of voids is observed at the interface for the two‐step deposition, which results in field‐effect mobilities as high as 1.2 cm² V^–1 s^–1; these are higher by more than a factor of two than those of the pentacene films deposited in one step. This remarkable increase in field‐effect mobility is due in particular to the interconnectivity of the pentacene grains near the insulator substrate.     

High‐Performance and Stable Organic Thin‐Film Transistors Based on Fused Thiophenes

A series of new organic semiconductors for organic thin‐film transistors (OTFTs) using dithieno[3,2‐b:2′,3′‐d]thiophene as the core are synthesized. Their electronic and optical properties are investigated using scanning electron microscopy (SEM), X‐ray diffraction (XRD), UV‐vis and photoluminescence spectroscopies, thermal gravimetric analysis (TGA), and differential scanning calorimetry (DSC). The compounds exhibit an excellent field‐effect performance with a high mobility of 0.42 cm² V^–1 s^–1 and an on/off ratio of 5 × 10⁶. XRD patterns reveal these films, grown by vacuum deposition, to be highly crystalline, and SEM reveals well‐interconnected, microcrystalline domains in these films at room temperature. TGA and DSC demonstrate that the phenyl‐substituted compounds possess excellent thermal stability. Furthermore, weekly shelf‐life tests (under ambient conditions) of the OTFTs based on the phenyl‐substituted compounds show that the mobility for the bis(diphenyl)‐substituted thiophene was almost unchanged for more than two months, indicating a high environmental stability.     

Anisotropic Structure and Charge Transport in Highly Strain‐Aligned Regioregular Poly(3‐hexylthiophene)

A novel method of strain‐aligning polymer films is introduced and applied to regioregular poly(3‐hexylthiophene) (P3HT), showing several important features of charge transport. The polymer backbone is shown to align in the direction of applied strain resulting in a large charge‐mobility anisotropy, where the in‐plane mobility increases in the applied strain direction and decreases in the perpendicular direction. In the aligned film, the hole mobility is successfully represented by a two‐dimensional tensor, suggesting that charge transport parallel to the polymer backbone within a P3HT crystal is strongly favored over the other crystallographic directions. Hole mobility parallel to the backbone is shown to be high for a mixture of plane‐on and edge‐on packing configurations, as the strain alignment is found to induce a significant face‐on orientation of the originally highly edge‐on oriented crystalline regions of the film. This alignment approach can achieve an optical dichroic ratio of 4.8 and a charge‐mobility anisotropy of 9, providing a simple and effective method to investigate charge‐transport mechanisms in polymer semiconductors.     

Inside Front Cover: High‐Performance and Stable Organic Thin‐Film Transistors Based on Fused Thiophenes (Adv. Funct. Mater. 3/2006)

A series of new organic semiconductors for organic thin‐film transistors using dithieno[3,2‐b:2′,3′‐d]thiophene as the core have been synthesized. In work reported by Liu, Zhu, and co‐workers on p. 426, the phenyl‐substituted compound exhibited a high mobility of 0.42 cm² V^–1 s^–1 and an on/off ratio of 5 × 10⁶. Weekly shelf‐life tests of the transistors based on the bis(diphenyl)‐substituted thiophene under ambient conditions showed that the mobility was almost unchanged after more than two months, demonstrating potential for applications in future organic electronics. A series of new organic semiconductors for organic thin‐film transistors (OTFTs) using dithieno[3,2‐b:2′,3′‐d]thiophene as the core are synthesized. Their electronic and optical properties are investigated using scanning electron microscopy (SEM), X‐ray diffraction (XRD), UV‐vis and photoluminescence spectroscopies, thermal gravimetric analysis (TGA), and differential scanning calorimetry (DSC). The compounds exhibit an excellent field‐effect performance with a high mobility of 0.42 cm² V^–1 s^–1 and an on/off ratio of 5 × 10⁶. XRD patterns reveal these films, grown by vacuum deposition, to be highly crystalline, and SEM reveals well‐interconnected, microcrystalline domains in these films at room temperature. TGA and DSC demonstrate that the phenyl‐substituted compounds possess excellent thermal stability. Furthermore, weekly shelf‐life tests (under ambient conditions) of the OTFTs based on the phenyl‐substituted compounds show that the mobility for the bis(diphenyl)‐substituted thiophene was almost unchanged for more than two months, indicating a high environmental stability.     

The Effect of Gate‐Dielectric Surface Energy on Pentacene Morphology and Organic Field‐Effect Transistor Characteristics

The effects of the surface energy of polymer gate dielectrics on pentacene morphology and the electrical properties of pentacene field‐effect transistors (FETs) are reported, using surface‐energy‐controllable poly(imide‐siloxane)s as gate‐dielectric layers. The surface energy of gate dielectrics strongly influences the pentacene film morphology and growth mode, producing Stranski–Krastanov growth with large and dendritic grains at high surface energy and three‐dimensional island growth with small grains at low surface energy. In spite of the small grain size (≈ 300 nm) and decreased ordering of pentacene molecules vertical to the gate dielectric with low surface energy, the mobility of FETs with a low‐surface‐energy gate dielectric is larger by a factor of about five, compared to their high‐surface‐energy counterparts. In pentacene growth on the low‐surface‐energy gate dielectric, interconnection between grains is observed and gradual lateral growth of grains causes the vacant space between grains to be filled. Hence, the higher mobility of the FETs with low‐surface‐energy gate dielectrics can be achieved by interconnection and tight packing between pentacene grains. On the other hand, the high‐surface‐energy dielectric forms the first pentacene layer with some voids and then successive, incomplete layers over the first, which can limit the transport of charge carriers and cause lower carrier mobility, in spite of the formation of large grains (≈ 1.3 μm) in a thicker pentacene film.     

Enhancement of Field‐Effect Mobility Due to Surface‐Mediated Molecular Ordering in Regioregular Polythiophene Thin Film Transistors

With the aim of enhancing the field‐effect mobility by promoting surface‐mediated two‐dimensional molecular ordering in self‐aligned regioregular poly(3‐hexylthiophene) (P3HT) we have controlled the intermolecular interaction at the interface between P3HT and the insulator substrate by using self‐assembled monolayers (SAMs) functionalized with various groups (–NH₂, –OH, and –CH₃). We have found that, depending on the properties of the substrate surface, the P3HT nanocrystals adopt two different orientations—parallel and perpendicular to the insulator substrate—which have field‐effect mobilities that differ by more than a factor of 4, and that are as high as 0.28 cm² V^–1 s^–1. This surprising increase in field‐effect mobility arises in particular for the perpendicular orientation of the nanocrystals with respect to the insulator substrate. Further, the perpendicular orientation of P3HT nanocrystals can be explained by the following factors: the unshared electron pairs of the SAM end groups, the π–H interactions between the thienyl‐backbone bearing π‐systems and the H (hydrogen) atoms of the SAM end groups, and interdigitation between the alkyl chains of P3HT and the alkyl chains of the SAMs.     

Confocal Raman Spectroscopy of α‐Sexithiophene: From Bulk Crystals to Field‐Effect Transistors

We report confocal micro‐Raman spectra of the organic semiconductor α‐sexithiophene (T6) on bulk crystals and on thin films grown on technologically relevant substrates and devices. We show that the two polymorphs, which are clearly identified by their lattice phonon spectra, may coexist as physical impurities of one inside the other in the same crystallite. Spatial distribution of the two phases is monitored by Raman phonon mapping of crystals grown upon different conditions. Raman microscopy has then been extended to T6 thin films grown on silicon oxide wafers. We identify the crystal phase in thin films whose thickness is just 18 nm. The most intense total‐symmetric Raman vibration is still detectable for a two‐monolayer thick film. Comparative analysis between micro‐Raman and AFM of T6 thin films grown on field effect transistors shows that electrode‐channel steps favour the nucleation and growth of T6 molecules on the substrate, at least below 50 nm.     

Air‐Stable n‐Type Organic Field‐Effect Transistors Based on Carbonyl‐Bridged Bithiazole Derivatives

An electronegative conjugated compound composed of a newly designed carbonyl‐bridged bithiazole unit and trifluoroacetyl terminal groups is synthesized as a candidate for air‐stable n‐type organic field‐effect transistor (OFET) materials. Cyclic voltammetry measurements reveal that carbonyl‐bridging contributes both to lowering the lowest unoccupied molecular orbital energy level and to stabilizing the anionic species. X‐ray crystallographic analysis of the compound shows a planar molecular geometry and a dense molecular packing, which is advantageous to electron transport. Through these appropriate electrochemical properties and structures for n‐type semiconductor materials, OFET devices based on this compound show electron mobilities as high as 0.06 cm² V^?1 s^?1 with on/off ratios of 10⁶ and threshold voltages of 20 V under vacuum conditions. Furthermore, these devices show the same order of electron mobility under ambient conditions.     

Probing the Anisotropic Field‐Effect Mobility of Solution‐Deposited Dicyclohexyl‐α‐quaterthiophene Single Crystals

Measuring the anisotropy of the field‐effect mobility provides insight into the correlation between molecular packing and charge transport in organic semiconductor materials. Single‐crystal field‐effect transistors are ideal tools to study intrinsic charge transport because of their high crystalline order and chemical purity. The anisotropy of the field effect mobility in organic single crystals has previously been studied by lamination of macroscopically large single crystals onto device substrates. Here, a technique is presented that allows probing of the mobility anisotropy even though only small crystals are available. Crystals of a soluble oligothiophene derivative are grown in bromobenzene and drop‐cast onto substrates containing arrays of bottom‐contact gold electrodes. Mobility anisotropy curves are recorded by measuring numerous single crystal transistor devices. Surprisingly, two mobility maxima occur at azimuths corresponding to both axes of the rectangular cyclohexyl‐substituted quaterthiophene (CH4T) in‐plane unit cell, in contrast to the expected tensorial behavior of the field effect mobility.     

Cover Picture: n‐Channel,Ambipolar, and p‐Channel Organic Heterojunction Transistors Fabricated with Various Film Morphologies (Adv. Funct. Mater. 3/2007)

Simultaneous introduction of short‐range repulsive interactions between dissimilar colloidal particles and attractive interactions between like particles provides a general new route to fabricating self‐organizing bipolar devices. By identifying combinations of conductive device materials between which short‐range repulsive forces exist in the presence of an intervening liquid, electrochemical junctions can be self‐formed, as reported by Chiang and co‐workers on p. 379. The relationship between the performance characteristics of organic field‐effect transistors (OFETs) with 2,5‐bis(4‐biphenylyl)bithiophene/copper hexadecafluorophthalocyanine (BP2T/F₁₆CuPc) heterojunctions and the thickness of the BP2T bottom layer is investigated. Three operating modes (n‐channel, ambipolar, and p‐channel) are obtained by varying the thickness of the organic semiconductor layer. The changes in operating mode are attributable to the morphology of the film and the heterojunction effect, which also leads to an evolution of the field‐effect mobility with increasing film thickness. In BP2T/F₁₆CuPc heterojunctions the mobile charge carriers accumulate at both sides of the heterojunction interface, with an accumulation layer thickness of ca. 10 nm. High field‐effect mobility values can be achieved in continuous and flat films that exhibit the heterojunction effect.     

Infiltration of Regioregular Poly[2,2′‐(3‐hexylthiopene)] into Random Nanocrystalline TiO2 Networks

Polymer infiltration into random nanocrystalline TiO₂ networks is examined using a combination of imaging, surface analysis, and depth‐profiling techniques. Nanocrystalline TiO₂ network substrates were fabricated by established methods; the resulting networks were examined using scanning electron microscopy and found to be typical of those reported in the literature. Regioregular poly[2,2′‐(3‐hexylthiopene)] (rrP3HT) was drop‐cast from solution onto the TiO₂‐network substrates. Infiltration of the polymer into the nanoporous TiO₂ network was determined by monitoring the ratio of carbon‐ion signal—by means of secondary‐ion mass spectrometry from a top overlayer of rrP3HT—to the carbon signal from the same polymer within the TiO₂ network. A very low incorporation of polymer was found (0.5 %), even for highly porous (≈ 65 %) networks. Several strategies were used to increase the degree of polymer infiltration, including heat treatment, surface derivatization, and the use of low‐molecular‐weight fractions. A high of 22 % rrP3HT as a percentage of the total volume of a random nanocrystalline film is reported. Previous results for hybrid rrP3HT/random nanocrystalline TiO₂ network devices are examined and analyzed in the context of these findings.     

n‐Channel,Ambipolar, and p‐Channel Organic Heterojunction Transistors Fabricated with Various Film Morphologies

The relationship between the performance characteristics of organic field‐effect transistors (OFETs) with 2,5‐bis(4‐biphenylyl)bithiophene/copper hexadecafluorophthalocyanine (BP2T/F₁₆CuPc) heterojunctions and the thickness of the BP2T bottom layer is investigated. Three operating modes (n‐channel, ambipolar, and p‐channel) are obtained by varying the thickness of the organic semiconductor layer. The changes in operating mode are attributable to the morphology of the film and the heterojunction effect, which also leads to an evolution of the field‐effect mobility with increasing film thickness. In BP2T/F₁₆CuPc heterojunctions the mobile charge carriers accumulate at both sides of the heterojunction interface, with an accumulation layer thickness of ca. 10 nm. High field‐effect mobility values can be achieved in continuous and flat films that exhibit the heterojunction effect.     

Alkyl‐Chain‐Length‐Independent Hole Mobility via Morphological Control with Poly(3‐alkylthiophene) Nanofibers

The field‐effect transistor (FET) and diode characteristics of poly(3‐alkylthiophene) (P3AT) nanofiber layers deposited from nanofiber dispersions are presented and compared with those of layers deposited from molecularly dissolved polymer solutions in chlorobenzene. The P3AT n‐alkyl‐side‐chain length was varied from 4 to 9 carbon atoms. The hole mobilities are correlated with the interface and bulk morphology of the layers as determined by UV–vis spectroscopy, transmission electron microscopy (TEM) with selected area electron diffraction (SAED), atomic force microscopy (AFM), and polarized carbon K‐edge near edge X‐ray absorption fine structure (NEXAFS) spectroscopy. The latter technique reveals the average polymer orientation in the accumulation region of the FET at the interface with the SiO₂ gate dielectric. The previously observed alkyl‐chain‐length‐dependence of the FET mobility in P3AT films results from differences in molecular ordering and orientation at the dielectric/semiconductor interface, and it is concluded that side‐chain length does not determine the intrinsic mobility of P3ATs, but rather the alkyl chain length of P3ATs influences FET diode mobility only through changes in interfacial bulk ordering in solution processed films.     

Extracting Parameters from the Current–Voltage Characteristics of Organic Field‐Effect Transistors

Organic field‐effect transistors were fabricated with vapor‐deposited pentacene on aluminum oxide insulating layers. Several methods are used in order to extract the mobility and threshold voltage from the transfer characteristic of the devices. In all cases, the mobility is found to depend on the gate voltage. The first method consists of deriving the drain current as a function of gate voltage (transconductance), leading to the so‐called field‐effect mobility. In the second method, we assume a power‐law dependence of the mobility with gate voltage together with a constant contact resistance. The third method is the so‐called transfer line method, in which several devices with various channel length are used. It is shown that the mobility is significantly enhanced by modifying the aluminum oxide layer with carboxylic acid self‐assembled monolayers prior to pentacene deposition. The methods used to extract parameters yield threshold voltages with an absolute value of less than 2 V. It is also shown that there is a shift of the threshold voltage after modification of the aluminum oxide layer. These features seem to confirm the validity of the parameter‐extraction methods.