Preparation and characterization of cellulose triacetate membranes via thermally induced phase separation

A series of cellulose triacetate (CTA) membranes were prepared via thermally induced phase separation (TIPS) process with dimethyl sulfone (DMSO2) and polyethylene glycol (PEG400) as a crystallizable diluent and an additive, respectively. The phase separation behavior of CTA/DMSO2/PEG400 ternary system was investigated in detail by optical microscopy, differential scanning calorimetry and wide angle X‐ray diffraction. This ternary system dynamically undergoes solid‐solid phase separation and thus the CTA membranes possess cellular, lacy, plate‐, or even ellipse‐shaped pores. However, we can modulate the pore structure, porosity, water flux, and mechanical properties of the membranes by varying polymer concentration, composition of the mixed diluent, and cooling condition. Due to the intrinsic hydrophilicity, the prepared CTA membranes have better antifouling property than polysulfone membranes. These porous membranes were used as supports to fabricate thin‐film composite forward osmosis (FO) membranes, which show good water permeability and selectivity. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44454.     

The cholesteric nature of cellulose triacetate solutions

Solutions of cellulose triacetate (CTA) in trifluoroacetic acid (TFA) become liquid crystalline above a certain critical concentration. Using the techniques of spectrophotometry, wide-angle light scattering and circular dichroism we have shown that the mesophase formed is cholesteric. We have measured its pitch, which depends on polymer concentration, and shown that the cholesteric structure is right-handed. Measurements of optical activity and the optical effects of shear and magnetic fields are also described and discussed.     

Electrospinning of fluorescent fibers from CdSe/ZnS quantum dots in cellulose triacetate

Fluorescent cellulose triacetate (CTA) fibers were prepared by electrospinning solutions of CTA dissolved in an 8 : 2 v/v cosolvent system of methylene chloride (MC) and methanol (MeOH) which contained CdSe/ZnS quantum dots (QDs). The relatively low loading of colloidal nanoparticles was sufficient to impart fluorescence to the fibers but did not significantly alter fiber morphologies, which tended toward smooth surfaces with the occasional longitudinal feature. The fibers were birefringent due to the alignment of the polymer chains which occurred during electrospinning and had widths on the order of a hundred nanometers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of cellulose acetate/cellulose triacetate ratio on reverse osmosis blend membrane performance

Surface functionalization and modification including the grafting process are effective approaches to improve and enhance the reverse osmosis (RO) membrane performance. This work is aimed to synthesize grafted/crosslinked cellulose acetate (CA)/cellulose triacetate (CTA) blend RO membranes using N-isopropylacrylamide (N-IPAAm) as a monomer and N,N-methylene bisacrylamide (MBAAm) as a crosslinker. The morphology of these membranes was analyzed by scanning electron microscopy and their surface roughness was characterized by atomic force microscopy. The performance of these membranes was evaluated through measuring two major parameters of salt rejection and water flux using RO unit at variable operating pressures. It was noted that the surface average roughness obviously decreased from 148 nm for the pure CA/CTA blend membrane with 2.5% CTA to 110 nm and 87 nm for the grafted N-IPAAm and grafted/crosslinked N-IPAAM/MBAAm/CA/CTA-RO membranes, respectively. Moreover, the contact angle decreased from 51.98° to 47.6° and 43.8° after the grafting and crosslinking process. The salt rejection of the grafted CA/CTA-RO membrane by 0.1% N-IPAAm produced the highest value of 98.12% and the water flux was 3.29 L/m²h at 10 bar.     

Preparation of polyester nanofibers and nanofiber yarns from polyester/cellulose acetate butyrate immiscible polymer blends

Development of high throughput production processes for making thermoplastic nanofiber and nanofiber yarns are urgently needed. PET, PTT, and PBT nanofibers were prepared from PET/CAB, PTT/CAB, PBT/CAB immiscible polymer blends by in situ microfibrillar formation during the melt extruding process. The diameter distribution and crystallization properties of PET, PTT, and PBT nanofibers were analyzed. After removing the CAB matrix phase, the nanofibers could be collected in the forms of random or aligned nanofibers and nanofiber bundles or yarns. To understand the formation mechanism of the nanofibers, the morphology development of three different polyesters in the dispersed phase were studied with samples collected at different zones in a twin‐screw extruder. The morphological development mechanism of the dispersed phases involved the formation of sheets, holes and network structures, then the size reduction and formation of nanofibers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Gel formation and liquid crystalline order in cellulose triacetate solutions

The formation of a liquid crystalline state of cellulose triacetate solution in trifluoroacetic acid was studied using optical microscopy, polarimetry and circular dichroism measurements. Below a critical concentration of $\text{34}\text{g}\text{100}\text{ml}$ a clear isotropic solution was formed. Solutions more concentrated than this were in the cholesteric liquid crystalline state. If water was added to the solution, a gel phase was formed if the polymer concentration was above a critical value. We interpret our observations in terms of the Pincus-de Gennes theory and show that the formation of liquid crystalline order involves both inter-and intramolecular forces.     

Release characteristics of four model drugs from drug-loaded electrospun cellulose acetate fiber mats

Ultra-fine fiber mats of cellulose acetate (CA; M_w ≈ 30?000 Da; degree of acetyl substitution ≈ 2.4) containing four different types of model drugs, i.e., naproxen (NAP), indomethacin (IND), ibuprofen (IBU), and sulindac (SUL), were successfully prepared by electrospinning from 16% w/v CA solutions in 2:1 v/v acetone/N,N-dimethylacetamide (DMAc). The amount of the drugs in the solutions was fixed at 20 wt.% based on the weight of CA powder. The morphology of the drug-loaded electrospun (e-spun) CA fiber mats was smooth, with the average diameters of these fibers ranging between 263 and 297 nm. No presence of the drug aggregates of any kind was observed on the surfaces of these fibers, suggesting that the drugs were encapsulated well within the fibers. After submersion in the acetate buffer solution at 37 °C for 24 h, the drug-loaded e-spun CA fiber mats swelled particularly well (i.e., 570-630%), while the corresponding solvent-cast film counterparts did not. The release characteristics of the model drugs from both the drug-loaded CA fiber mats and the drug-loaded as-cast CA films were carried out by the total immersion method in the acetate buffer solution at 37 °C. At any given immersion time point, the release of the drugs from the drug-loaded e-spun CA fiber mats was greater than that from the corresponding as-cast films. The maximum release of the drugs from both the drug-loaded fiber mats and films could be ranked as follows: NAP > IBU > IND > SUL.     

The problem of refining cellulose triacetate solutions with fibrous ion-exchange resins

Conclusions The process of cleaning up cellulose acetate spinning solutions and model solutions from traces of acid dyes with polyacrylonitrile fibre anion-exchangers has been investigated. Optimum conditions for carrying out the clean-up have been determined.It is recommended to use ion-exchange resin type PAN(2)cp-PEA, prepared using a polyamine preparation, to clean up the spinning solution.Translated from Khimicheskie Volokna, No. 5, pp. 16–17, September–October, 1985.     

Rapid synthesis of cellulose triacetate from cotton cellulose and its effect on specific surface area and particle size distribution

A highly rapid process is described for the preparation of cellulose triacetate and its effect on particle size and surface area of the product. The process involves microwave-assisted rapid synthesis of cellulose triacetate with very low amount of acetic anhydride (10–15% of acetic anhydride is used in conventional methods) in the presence of iodine as a catalyst using a designed reaction vessel. The technique used is simple and rapid; it is also characterized by a high conversion ratio (yield 100%). A small amount of iodine (115 and 230 mg, 1.15 and 2.3% of cellulose weight) was found to be effective in the production of cellulose triacetate using 25, 30 to 40 mL acetic anhydride for 10 g cellulose under microwave irradiation for 2–4 min. The production of cellulose triacetate and the degree of substitution were confirmed by FTIR, Raman, ¹H NMR, and thermogravimetric analysis. The optimal reaction condition was discovered to be 3 min microwave radiation and 30 mL acetic anhydride in the presence of 230 mg iodine for 10 g cellulose. The effects of the amount of acetic anhydride, and amount of catalyst and reaction time on the specific surface area, pore volume, mean pore diameter, and particle size distribution were investigated. The highest surface area obtained was 39.63 m²/g. The specific surface area and particle size distribution are highly dependent on the amount of acetic anhydride and I₂ catalyst. About 10% of the synthesized cellulose acetate showed particle size less than 200 nm.     

Viscometric behavior of concentrated cellulose acetate solutions

The viscometric behavior of concentrated cellulose acetate solutions in a variety of solvent and mixed solvent systems has been studied. Rapid increases in solution viscosity with increase in cellulose acetate concentration are apparently related to polymer nonsphericity and the tendency of molecules to experience extensive nonhydrodynamic interactions. By employing a well-defined polymer solution theory in conjunction with an empirically determined calibration curve, accurate predictions of concentrated cellulose acetate solution viscosities are possible.     

VIscometric behaviour of Kevlar fibre filled liquid crystalline solutions of ethyl cellulose in m-cresol

Liquid crystalline solutions of ethyl cellulose in m-cresol were mixed with Kevlar® fibres, and the viscometric behaviour with respect to temperature of those filled systems was determined with a cone-plate type viscometer. The viscosity of the systems exhibited a maximum and a minimum at temperatures denoted by T_max and T_min' respectively. The effects of fibre on the critical temperatures (T_max and T_min) and critical concentrations (C_a and C_b) and on the viscosity enhancement are discussed. T_max and T_min decreased with fibre concentration for single-phase anisotropic solutions, whereas they increased for the biphasic solution. The critical concentrations increased with fibre concentration and C_b was more sensitive to the fibre than C_a. The viscosity enhancement due to the fibre depended on the phase of solution. In the single-phase (isotropic and anisotropic), the viscosity enhanced with fibre; however, in the biphasic solution, the effect was not simple. The viscosity enhancement for the single-phase anisotropic solutions with fibre was lower than that for the isotropic solutions.     

Modified polyacrylonitrile blends with cellulose acetate: Fibers' properties

Fiber forming polyacrylonitriles (PAN) were modified by copolymerizing acrylonitrile monomer with methyl acrylate (MA) and 2-acrylamido-2-methyl propane sulfonic acid (AP), respectively, and blended with collulose acetate (CA). Fibers of MA-PAN, AP-PAN, and their blends with CA were wet-spun in dimethylformamide in a broad range of coagulation bath concentrations (CBC). The effects of hydrophilic and hydrophobic modification of PAN and the CBC, as well as the coagulation behavior, were studied in terms of morphology, mechanical properties, and water regain property of the fibers. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1937–1946, 1997     

Yarn spinning stability from a cellulose triacetate melt

Conclusions In spinning yarns from a cellulose triacetate melt on a unit with a heatable spinneret, it is possible to calculate spinning parameters which ensure obtaining a yarn having a low degree of nonuniformity, both with respect to linear density and also in physicomechanical properties.The smaller the diameter of the spinneret holes, the greater the uniformity and the higher the physicomechanical properties of the yarn.Translated from Khimicheskie Volokna, No. 6, pp. 29–30, November–December, 1985.     

Effect of solvent on morphology of electrospinning ethyl cellulose fibers

The influence of the composition of a multicomponent solvent on the surface morphology and diameter distribution of ethyl cellulose fibers produced by electrospinning technology was investigated. The results showed that the average diameter of the fibers using the multicomponent solvent was thinner than when using either of the two components and the diameter distribution of the fibers became narrower. Tiny tubercles formed on the fiber surface, which may improve the specific surface area and broaden the applications. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1292–1297, 2005     

A structure rheological study of cellulose trinitrate in ethyl acetate

A structure rheological analysis was undertaken with cellulose trinitrates dissolved in ethyl acetate. Empirical scaling laws with molecular mass and concentration were found for the zero shear viscosity η_o and the critical shear rate $ \dot \gamma _C $ at the onset of shear thinning. Values for the apparent chain element A' were calculated from the concentration dependent network strand M_e and extrapolated to zero concentration. They were compared with dilute solution data. From the concentration dependence of the mass of network strand M_e a network with hindered penetration was inferred.