Reliable Monolayer‐Template Patterning of SnO2 Thin Films from Aqueous Solution and Their Hydrogen‐Sensing Properties

We demonstrate a novel lithographic technique utilizing a solvent to fabricate a chemically based semiconductor microdevice from an aqueous solution. According to this technique, SnO₂ thin film could be integrated onto predefined sites on a SiO₂/Si wafer. A patterned octadecyltrimethoxysilane self‐assembled monolayer (ODS‐SAM) was prepared by vacuum ultraviolet (VUV) irradiation through a photomask to use as a template for the fabrication of a micropatterned SnO₂ thin film on the SiO₂/Si surface. A Sn‐based thin film was then deposited onto the entire surface of the ODS template from an aqueous solution containing 0.03 mol L^–1 of SnCl₂·2H₂O at 60 °C for 16 h in an ambient atmosphere. The thin film deposited on the methyl‐terminated area of the template was then peeled using an ultrasonic rinse in anhydrous toluene for 30 min, while the film deposited on the silanol area remained intact and undamaged. Rinsing in hydrophilic solvents did not facilitate peeling of the thin film from the methyl‐terminated area. We succeeded by this process in obtaining a high‐resolution, micropatterned Sn‐based thin film on an ODS‐SAM template on Si. The as‐deposited film was composed of fine Sn‐based particles. The sensitivity of this SnO₂ thin film to H₂ gas increases linearly with improving crystallinity. The effectiveness of anhydrous toluene as a rinse in solution lithography is discussed from the viewpoint of the high hydrophobic affinity between the rinse solvent and the terminal groups in the monolayer template.     

Hydrothermally Stable Thioether‐Bridged Mesoporous Materials with Void Defects in the Pore Walls

Hydrothermally stable thioether‐bridged mesoporous materials have been synthesized by one‐step co‐condensation of 1,4‐bis(triethoxysily)propane tetrasulfide (TESPTS) with tetramethoxysilane (TMOS) using cetyltrimethylammonimum bromide (CTAB) as the surfactant in basic conditions. The ordered mesoporous materials can be formed with a wide range of thioether concentrations in the mesoporous framework, as is seen by X‐ray diffraction (XRD) characterization. The results of N₂ sorption and transmission electron microscopy (TEM) reveal that the materials synthesized with TESPTS/TMOS molar ratios in the range 1:8–1:3 have extensive structural defect holes in the nanochannels. All materials exhibit enhanced hydrothermal stability, which is in proportion to the concentration of thioether bridging in the mesoporous framework. The thioether‐functionalized mesoporous materials are efficient adsorbents for removing Hg²⁺ and phenol from waste water. The Hg²⁺‐adsorption capacity of the material can be as high as 1500 mg g^–1.     

Thermally Stable Two‐Dimensional Hexagonal Mesoporous Nanocrystalline Anatase,Meso‐nc‐TiO2: Bulk and Crack‐Free Thin Film Morphologies

Herein a novel synthetic route is described for the production of thermally stable, structurally well‐defined two‐dimensional (2D) hexagonal mesoporous nanocrystalline anatase (meso‐nc‐TiO₂), with a large pore diameter, narrow pore‐size distribution, high surface area, and robust inorganic walls comprised of nanocrystalline anatase. The synthetic approach involves the evaporation‐induced co‐assembly of a non‐ionic amphiphilic triblock‐copolymer template and titanium tetraethoxide, but with a pivotal change in the main solvent of the system, where the commonly used ethanol is replaced with 1‐butanol. This seemingly minor modification in solvent type from ethanol to 1‐butanol turns out to be the key synthetic strategy for achieving a robust, structurally well‐ordered meso‐nc‐TiO₂ material in the form of either thick or thin films. The beneficial “solvent” effect originates from the higher hydrophobicity of 1‐butanol than ethanol, enhancing microphase separation and templating, lower critical micelle concentration of the template in 1‐butanol, and the ability to increase the relative concentration of the inorganic precursor to template in the co‐assembly synthesis. Moreover, thin films with dimensions of several centimeters that are devoid of cracks down to the length scale of the mesostructure itself, having high porosity, well‐defined mesostructural features, and semi‐crystalline pore walls were straightforwardly and reproducibly obtained as a result of the physicochemical property advantages of 1‐butanol over ethanol within our synthesis scheme.     

Recent Advances in the Design of Polymerizable Lyotropic Liquid‐Crystal Assemblies for Heterogeneous Catalysis and Selective Separations

Organic lyotropic liquid‐crystal (LLC) assemblies mimic molecular sieves in their nanoporous structures and their ability to incorporate catalytic functional groups. This article focuses on recent advances made by our research group in incorporating new catalytic properties into polymerizable LLC assemblies and studying the molecular‐transport properties of the crosslinked networks.     

Facile Synthesis of Manganese‐Loaded Mesoporous Silica Materials by Direct Reaction Between KMnO4 and an In‐Situ Surfactant Template

A series of manganese oxide‐loaded SBA‐15 (MnSBA‐xh, x = 1, 2, 3, 4, 5, 6; h: hour(s)) mesoporous materials are synthesized via a facile, in‐situ reduction method with a surfactant template. The composite materials are characterized using Fourier‐transform infrared spectroscopy, X‐ray diffraction, N₂ sorption isotherms, X‐ray photoelectron spectroscopy (XPS), transmission electron microscopy, energy‐dispersive spectroscopy, and CO oxidation catalysis. The results show that a high content of manganese (an atomic ratio of Mn/Si from 0.12 up to approximately 1) could be loaded into the channels of SBA‐15 when treated with an aqueous solution of potassium permanganate, while retaining the ordered mesostructure and large surface area of SBA‐15. Increasing the manganese oxide content results in a gradual decrease in the specific surface area, pore size, and pore volume. XPS spectra are employed to confirm the redox reaction between KMnO₄ and the surfactant. CO‐conversion tests on the calcined MnSBA‐2h sample (MnSBA‐2h‐cal) shows that it has a repeatable, and relatively high, catalytic activity.     

Highly Organized Mesoporous TiO2 Films with Controlled Crystallinity: A Li‐Insertion Study

A study of electrochemical Li insertion combined with structural and textural analysis enabled the identification and quantification of individual crystalline and amorphous phases in mesoporous TiO₂ films prepared by the evaporation‐induced self‐assembly procedure. It was found that the properties of the amphiphilic block copolymers used as templates, namely those of a novel poly(ethylene‐co‐butylene)‐b‐poly(ethylene oxide) polymer (KLE) and commercial Pluronic P123 (HO(CH₂CH₂O)₂₀(CH₂CH(CH₃)O)₇₀(CH₂CH₂O)₂₀H), decisively influence the physicochemical properties of the resulting films. The KLE‐templated films possess a 3D cubic mesoporous structure and are practically amorphous when calcined at temperatures below 450 °C, but treatment at 550–700 °C provides a pure‐phase (anatase), fully crystalline material with intact mesoporous architecture. The electrochemically determined fraction of crystalline anatase increases from 85 to 100 % for films calcined at 550 and 700 °C, respectively. In contrast, the films prepared using Pluronic P123, which also show a 3D cubic pore arrangement, exhibit almost 50 % crystallinity even at a calcination temperature of 400 °C, and their transformation into a fully crystalline material is accompanied by collapse of the mesoporous texture. Therefore, our study revealed the significance of using suitable block‐copolymer templates for the generation of mesoporous metal oxide films. Coupling of both electrochemical and X‐ray diffraction methods has shown to be highly advisable for the correct interpretation of structure properties, in particular the crystallinity, of such sol–gel derived films.     

Spin‐Coated Periodic Mesoporous Organosilica Thin Films—Towards a New Generation of Low‐Dielectric‐Constant Materials

Periodic mesoporous organosilica (PMO) thin films have been produced using an evaporation‐induced self‐assembly (EISA) spin‐coating procedure and a cationic surfactant template. The precursors are silsesquioxanes of the type (C₂H₅O)₃Si–R–Si(OC₂H₅)₃ or R′–[Si(OC₂H₅)₃]₃ with R = methene (–CH₂–), ethylene (–C₂H₂–), ethene (–C₂H₄–), 1,4‐phenylene (C₆H₄), and R′ = 1,3,5‐phenylene (C₆H₃). The surfactant is successfully removed by solvent extraction or calcination without any significant Si–C bond cleavage of the organic bridging groups R and R′ within the channel walls. The materials have been characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), powder X‐ray diffraction (PXRD), and ²⁹Si and ¹³C magic‐angle spinning (MAS) NMR spectroscopy. The d‐spacing of the PMOs is found to be a function of R. Nanoindentation measurements reveal increased mechanical strength and stiffness for the PMOs with R = CH₂ and C₂H₄ compared to silica. Films with different organic‐group content have been prepared using mixtures of silsesquioxane and tetramethylorthosilicate (TMOS) precursors. The dielectric constant (k) is found to decrease with organic content, and values as low as 1.8 have been measured for films thermally treated to cause a “self‐hydrophobizing” bridging‐to‐terminal transformation of the methene to methyl groups with concomitant loss of silanols. Increasing the organic content and thermal treatment also increases the resistance to moisture adsorption in 60 and 80 %‐relative‐humidity (RH) environments. Methene PMO films treated at 500 °C are found to be practically unchanged after five days exposure to 80 % RH. These low dielectric constants, plus the good thermal and mechanical stability and the hydrophobicity suggest the potential utility of these films as low‐k layers in microelectronics.     

Highly Ordered Mesoporous Silicon Carbide Ceramics with Large Surface Areas and High Stability

Highly ordered mesoporous silicon carbide ceramics have been successfully synthesized with yields higher than 75 % via a one‐step nanocasting process using commercial polycarbosilane (PCS) as a precursor and mesoporous silica as hard templates. Mesoporous SiC nanowires in two‐dimensional (2D) hexagonal arrays (p6m) can be easily replicated from a mesoporous silica SBA‐15 template. Small‐angle X‐ray diffraction (XRD) patterns and transmission electron microscopy (TEM) images show that the SiC nanowires have long‐range regularity over large areas because of the interwire pillar connections. A three‐dimensional (3D) bicontinuous cubic mesoporous SiC structure (Ia3d) can be fabricated using mesoporous silica KIT‐6 as the mother template. The structure shows higher thermal stability than the 2D hexagonal mesoporous SiC, mostly because of the 3D network connections. The major constituent of the products is SiC, with 12 % excess carbon and 14 % oxygen measured by elemental analysis. The obtained mesoporous SiC ceramics are amorphous below 1200 °C and are mainly composed of randomly oriented β‐SiC crystallites after treatment at 1400 °C. N₂‐sorption isotherms reveal that these ordered mesoporous SiC ceramics have high Brunauer–Emmett–Teller (BET) specific surface areas (up to 720 m² g^–1), large pore volumes (～ 0.8 cm³ g^–1), and narrow pore‐size distributions (mean values of 2.0–3.7 nm), even upon calcination at temperatures as high as 1400 °C. The rough surface and high order of the nanowire arrays result from the strong interconnections of the SiC products and are the main reasons for such high surface areas. XRD, N₂‐sorption, and TEM measurements show that the mesoporous SiC ceramics have ultrahigh stability even after re‐treatment at 1400 °C under a N₂ atmosphere. Compared with 2D hexagonal SiC nanowire arrays, 3D cubic mesoporous SiC shows superior thermal stability, as well as higher surface areas (590 m² g^–1) and larger pore volumes (～ 0.71 cm³ g^–1).     

Hydrogen‐Bonded Liquid Crystals in Confined Spaces—Toward Photonic Hybrid Materials

A series of hybrid materials based on chiral nematic mesoporous organosilica (CNMO) films infiltrated with liquid crystalline hydrogen‐bonded assemblies is prepared and characterized with respect to the mutual manipulation of the photonic properties of the host and the liquid‐crystalline behavior of the guest. Detailed differential scanning calorimetry studies reveal the impact of confinement on the mesomorphic behavior of the liquid crystalline assemblies in the pores of the CNMO films. The photonic properties of the chiral nematic mesoporous host can be controlled by changing the temperature or irradiating the films with UV light. These stimuli‐induced phase transitions are accompanied by changes in the orientational order of the mesogens as revealed by ¹⁹F NMR spectroscopy. The combination of confinement and changes in the molecular orientation in a unique hybrid material based on hydrogen‐bonded liquid crystals and a porous host with a chiral nematic mesostructure is an interesting concept for the design of optical sensors, reflectors, or filters.     

Combined Surface and Volume Templating of Highly Porous Nanocast Carbon Monoliths

Nanocast carbon monoliths exhibiting a three‐ or four‐modal porosity have been prepared by one‐step impregnation, using silica monoliths containing a bimodal porosity as the scaffold. Combined volume and surface templating, together with the controlled synthesis of the starting silica monoliths used as the scaffold, enables a flexible means of pore‐size control on several length scales simultaneously. The monoliths were characterized by nitrogen sorption, scanning electron microscopy, transmission electron microscopy, and mercury porosimetry. It is shown that the carbon monoliths represent a positive replica of the starting silica monoliths on the micrometer length scale, whereas the volume‐templated mesopores are a negative replica of the silica scaffold. In addition to the meso‐ and macropores, the carbon monoliths also exhibit microporosity. The different modes of porosity are arranged in a hierarchical structure‐within‐structure fashion, which is thought to be optimal for applications requiring a high surface area in combination with a low pressure drop over the material.     

Spatial and Orientational Templating of Semiconducting Polymers in a Cholesteric Liquid Crystal

A one‐dimensional pattern‐forming state of a cholesteric liquid crystal (CLC) is used as a template for the self‐organization of ordered, spatially orientated, acetylene‐based semiconducting polymers. The polymers are formed by metathesis reaction with all chemical components contained in an ordinary electro‐optic cell. The polymer morphology consists of parallel ～ 1 μm thick bundles, uniformly spaced at ～ 10 μm over the full macroscopic active area of the cell substrates. The polymer templating can be explained by a model that predicts a corrugation in polymer density determined by the spatially periodic profile of the orientational energy density associated with the pattern‐forming CLC state.     

Probing the Anisotropic Field‐Effect Mobility of Solution‐Deposited Dicyclohexyl‐α‐quaterthiophene Single Crystals

Measuring the anisotropy of the field‐effect mobility provides insight into the correlation between molecular packing and charge transport in organic semiconductor materials. Single‐crystal field‐effect transistors are ideal tools to study intrinsic charge transport because of their high crystalline order and chemical purity. The anisotropy of the field effect mobility in organic single crystals has previously been studied by lamination of macroscopically large single crystals onto device substrates. Here, a technique is presented that allows probing of the mobility anisotropy even though only small crystals are available. Crystals of a soluble oligothiophene derivative are grown in bromobenzene and drop‐cast onto substrates containing arrays of bottom‐contact gold electrodes. Mobility anisotropy curves are recorded by measuring numerous single crystal transistor devices. Surprisingly, two mobility maxima occur at azimuths corresponding to both axes of the rectangular cyclohexyl‐substituted quaterthiophene (CH4T) in‐plane unit cell, in contrast to the expected tensorial behavior of the field effect mobility.     

Template‐Assisted Synthesis of Mesoporous Magnetic Nanocomposite Particles

A new concept is proposed to synthesize mesoporous magnetic nanocomposite particles of great scientific and technological importance. Mesoporous silica coatings were created on micrometer‐sized magnetite (Fe₃O₄) particles using cetyltrimethylammonium chloride micelles as molecular templates. The characterization by transmission electron microscopy (TEM), nitrogen adsorption–desorption, diffuse‐reflectance Fourier‐transform infrared spectroscopy, and zeta‐potential measurements confirmed the deposition of mesoporous silica thin layers on the magnetite particles. The synthesized particles showed a drastic increase in specific surface area with an average pore size of 2.5 nm. The coating material showed a negligible effect on the saturation magnetization of the original particles that were fully protected by silica coatings. The synthesized mesoporous magnetic nanocomposite particles have a wide range of applications in toxin removal, waste remediation, catalysis, reactive sorbents, and biological cell separations.     

Formation of Polyaniline Nanorod/Liquid Crystalline Epoxy Composite Nanowires Using a Temperature‐Gradient Method

Liquid crystalline epoxy/polyaniline (LCE/PANI) composite nanowires have been fabricated using an anodic aluminum oxide (AAO) membrane by a temperature‐gradient curing process. PANI nanorods with an average diameter of 30 nm have been synthesized by dispersion polymerization in order to employ them as a curing agent for LCE and as a reinforcement filler for the LCE/PANI composite nanowires. Differential scanning calorimetry and Fourier‐transform infrared spectroscopy indicate that the LCE crosslinking reaction occurred inside the channels of the AAO membrane via the curing of LCE with PANI nanorods. The LCE/PANI composite nanowires exhibit an enhanced electrical conductivity and thermal stability, comparable with a LCE/PANI composite monolith. In addition, these polymer‐composite nanowires also display the characteristics of a functionally gradient conducting material.     

Amplified Spontaneous Emission in Close‐Packed Films of Semiconductor Nanocrystals Using Picosecond Excitation

We present experimental observations of line‐narrowing of the photoluminescence in close‐packed thin films of CdSe nanocrystals with epitaxial ZnS shells, under excitation from a pulsed source of 100 ps duration, both at 77 K and at room temperature (RT). Atomic force microscopy (AFM) of these films reveals them to be optically flat to less than 1 % of the emission wavelength and we propose that waveguiding and amplified spontaneous emission is the principal mechanism for line‐narrowing. We observe that line‐narrowing is assisted by the use of films with a bimodal distribution of nanocrystal sizes, where the excited state population is concentrated on the larger nanocrystals due to energy transfer.     

Engineering of Self‐Assembled Domain Architectures with Ultra‐high Piezoelectric Response in Epitaxial Ferroelectric Films

Substrate clamping and inter‐domain pinning limit movement of non‐180° domain walls in ferroelectric epitaxial films thereby reducing the resulting piezoelectric response of ferroelectric layers. Our theoretical calculations and experimental studies of the epitaxial PbZr_xTi_1–xO₃ films grown on single crystal SrTiO₃ demonstrate that for film compositions near the morphotropic phase boundary it is possible to obtain mobile two‐domain architectures by selecting the appropriate substrate orientation. Transmission electron microscopy, X‐ray diffraction analysis, and piezoelectric force microscopy revealed that the PbZr_0.52Ti_0.48O₃ films grown on (101) SrTiO₃ substrates feature self‐assembled two‐domain structures, consisting of two tetragonal domain variants. For these films, the low‐field piezoelectric coefficient measured in the direction normal to the film surface (d₃₃) is 200 pm V^–1, which agrees well with the theoretical predictions. Under external AC electric fields of about 30 kV cm^–1, the (101) films exhibit reversible longitudinal strains as high as 0.35 %, which correspond to the effective piezoelectric coefficients in the order of 1000 pm V^–1 and can be explained by elastic softening of the PbZr_xTi_1–xO₃ ferroelectrics near the morphotropic phase boundary.     

Mosaic,Single‐Crystal CaCO3 Thin Films Fabricated on Modified Polymer Templates

Mosaic, single‐crystal CaCO₃ thin films have been prepared on modified poly(ethylene terephthalate) (PET) templates. Surface modification of PET through the introduction of carboxylic acid groups (COOH‐PET), and the subsequent physical and chemical adsorption of poly(allylamine hydrochloride) (PAH) at pH 8 (PAH8‐PET) and pH 11 (PAH11‐PET), afford template surfaces that influenced the phase transition of an amorphous CaCO₃ (ACC) films during crystallization in air. Macroscopic ACC thin films are prepared on modified PET films in the presence of poly(acrylic acid). Polycrystalline, spherulitic vaterite (CaCO₃) films are observed to form on native PET and PAH11‐PET, while mosaic, single‐crystal calcitic (CaCO₃) films form on COOH‐PET and PAH8‐PET templates. These results confirm that single‐crystal CaCO₃ growth patterns are dependent on the surface characteristics of the PET template. We infer therefore, that the nucleation and growth of ceramic films on polymeric templates can be controlled by chemical modification of the polymeric template surface, and by the subsequent attachment of ionic polyelectrolytes.     

Template‐Assisted Self‐Assembly of Spherical Colloids into Complex and Controllable Structures

Colloidal aggregates with well‐controlled sizes, shapes, and structures have been fabricated by dewetting aqueous dispersions of monodispersed spherical colloids across surfaces patterned with two‐dimensional arrays of relief structures (or templates). The capability and feasibility of this approach have been demonstrated with the organization of polymer latex or silica beads into homo‐aggregates, including circular rings; polygonal and polyhedral clusters; and linear, zigzag, and spiral chains. It was also possible to generate hetero‐aggregates in the configuration of HF and H₂O molecules that contained spherical colloids of different sizes, compositions, densities, functions, or a combination of these features. These uniform, well‐defined aggregates of spherical colloids are ideal model systems to investigate the aerodynamic, hydrodynamic, and optical properties of colloidal particles characterized by non‐spherical shapes and/or complex topologies. They can also serve as a new class of building blocks to generate hierarchically self‐assembled structures that are expected to exhibit interesting features valuable to areas ranging from condensed matter physics to photonics.     

High‐Yield Fabrication and Electrochemical Characterization of Tetrapodal CdSe,CdTe, and CdSexTe1–x Nanocrystals

The high‐yield fabrication of tetrapodal CdSe, CdTe, and CdSe_xTe_1–x nanocrystals is systematically studied. CdSe nanocrystals are prepared by first controlling the synthesis of high‐quality wurtzite CdSe and zinc blende CdSe nanocrystals at a relatively high temperature (260 °C) by selecting different ligands. Then, based on the phase control of the CdSe nanocrystals, two nanoparticle‐tailoring routes (i.e., a seed‐epitaxial route and ligand‐dependent multi‐injecting route) are used, and a high yield of CdSe tetrapods is obtained. CdTe nanocrystals are prepared by adjusting the ligand composition and the ratio of Cd to Te; CdTe tetrapods are synthesized in high yield using a mixed ligand that does not contain alkylphosphonic acids. Moreover, the nanoscale Te powder (Te nanowires/nanorods), which is highly soluble in the ligand solvent, is first used as a Te source to synthesize CdTe nanocrystals, which remarkably enhanced the output of the CdTe nanocrystals in one reaction. Furthermore, composition‐tunable ternary CdSe_xTe_1–x alloyed tetrapods are synthesized on a large scale, for the first time, by thermolyzing the mixture of the organometallic Cd precursor and the mixed (Se + Te) source in a mixed‐ligand solution. The CdSe, CdTe, and CdSe_xTe_1–x nanocrystals are characterized by transmission electron microscopy (TEM), high‐resolution TEM, selected‐area electron diffraction, X‐ray diffraction, and UV‐vis and photoluminescence (PL) spectroscopy. Interesting nonlinear, composition‐dependent absorption and PL spectra are observed for the ternary CdSe_xTe_1–x alloyed nanocrystals. The band‐edge positions of the nanocrystals of CdSe, CdSe_xTe_1–x, and CdTe are systematically studied by cyclic voltammetry.