Preparation and characterization of poly(butyl acrylate‐co‐2‐ethylhexyl acrylate) grafting of vinyl chloride resin with good impact resistance

Crosslinked poly(butyl acrylate‐co‐2‐ethylhexyl acrylate) [P(BA–EHA)] latex was synthesized by seeded emulsion polymerization. P(BA–EHA)/poly(vinyl chloride) (PVC) composite latex was prepared using P(BA–EHA) latex as the seed. The effects of the amount of P(BA–EHA) on the latex particle diameters and mechanical properties of the materials are discussed. The grafting efficiency (GE) of P(BA–EHA)‐grafted vinyl chloride (VC) in the synthesized resin was investigated, and the GE increased with an increasing P(BA–EHA)/VC ratio. The morphology of P(BA–EHA)/PVC was characterized using TEM, SEM, and DMA. TEM indicated that the particles of the P(BA–EHA)/PVC composite latex have a clear core–shell structure. DMA illustrated that the compatibility between P(BA–EHA) and PVC was well improved. With an increasing P(BA–EHA) content, the loss peak in the low‐temperature range became stronger than that of pure PVC, and the maximum values of the loss peaks gradually shifted to higher temperature. SEM showed that the fractured surface of the composite sample exhibited better toughness of the material. The notched impact strength of the material with 4.2 wt % P(BA–EHA) was 11 times that of PVC. TEM showed that P(BA–EHA) was uniformly dispersed in the PVC matrix and that the interface between the two phases was indistinct. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 643–649, 2003     

Synthesis and characterization of poly(butyl acrylate‐co‐ethylhexyl acrylate)/ poly(vinyl chloride)[P(BA‐EHA)/PVC] novel core‐shell modifier and its impact modification for a poly(vinyl chloride)‐based blend

Synthesis of poly(butyl acrylate‐co‐ethylhexyl acrylate)‐core/poly(vinyl chloride)‐shell [P(BA‐EHA)/PVC] used as a modifying agent of PVC via semicontinuous seeded emulsion copolymerization is reported here. Diameter distributions and morphology of the composite latex particles were characterized with the aid of particle size analyzer and transmission electron microscopy (TEM). The grafting efficiency (GE) and grafting ratio (GR) of vinyl chloride (VC) grafted onto the P(BA‐EHA) with varying content of crosslinking agent and core‐shell ratios were investigated. TEM studies indicated that the P(BA‐EHA)/PVC latex particles have core‐shell structure, and the P(BA‐EHA) rubbery particles in blending materials were uniformly dispersed in PVC matrix. Dynamic mechanical analysis (DMA) results revealed that the compatibility between the P(BA‐EHA) and the PVC matrix was significantly improved due to the presence of the P(BA‐EHA)‐grafted‐VC copolymer. The notched impact strength of the blending material with 3 wt% of rubber content was seven times that of the PVC. Linear regressions of mechanical properties as loading of the modifier were made. The resulting data of notched impact strength and elongation at break for the blending materials deviated significantly from regression lines within 3–4.5 wt% of the P(BA‐EHA) content. The PVC blends modified by the modifier exhibited good toughness and easy processability. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

A tough noncombustible material prepared by grafting of poly(2‐ethylhexyl acrylate) with vinyl chloride

A noncombustible tough poly(vinyl chloride) (tPVC) was prepared by suspension‐grafted copolymerization of poly(2‐ethylhexyl acrylate) (poly‐EHA; elastomer) with vinyl chloride (VC). Elastomer (poly‐EHA) was prepared by emulsion, mainly homopolymerization of 2‐ethylhexyl acrylate at a temperature of 30 ± 0.1°C in the presence of a redox system and with the advantage of dosing the monomer into two portions. Grafted‐suspension copolymerization of poly‐EHA with VC was carried out at 54 ± 0.1°C, keeping other reaction conditions only slightly modified in comparison with those for the polymerization of pure VC. An optimum content of the incorporated poly‐EHA in PVC was found to be in the range 7.5–8.5 wt %, whereas notched toughness of 85–87 kJ m^?2 was reached. Both below and above the found range of the content of poly‐EHA, the toughness decreases. A copolymer prepared by a direct‐emulsion copolymerization of 2‐EHA and VC (poly‐EHA‐co‐VC) exhibited worse mechanical properties than the copolymer prepared by two polymerization steps. On the basis of experimental results, effects of the reaction procedure on the properties of resulting material are described. In addition to good mechanical properties, tPVC also shows its noncombustibly. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2355–2362, 2002     

有机锡参与合成P(BA-EHA)/PVC及共混改性PVC的结构与性能

通过种子乳液聚合方法,采用丙烯酸丁酯(BA)、丙烯酸2-乙基己酯(EHA)为核层单体,与少量有机锡单体共聚制备了含有机锡的P(BA-EHA)胶乳,与氯乙烯(VC)乳液接枝共聚合成了P(BA-EHA)/PVC复合改性剂。通过透射电子显微镜(TEM)、动态力学分析仪(DMA)、扫描电子显微镜(SEM)等测试手段,考察了复合乳胶粒子和共混材料的形态结构、复合改性剂中有机锡含量对其共混改性PVC材料的力学性能及复合粒子热稳定性的影响。DMA和TEM分析结果表明:复合粒子的加入显著改善了橡胶相与PVC之间的相容性,P(BA-EHA)在PVC基体中具有很好的分散性和均匀度,SEM照片显示共混材料缺口断面表现为优异的基体屈服型断裂韧性。     

Properties of PHMS‐g‐p [butylacrylate (BA)‐N‐hydroxyl‐methyl acrylamide (NMA)] graft copolymer emulsions

Emulsion graft copolymerization of poly(hydrogenmethylsiloxane) (PHMS) and butyl acrylate (BA) in the presence of functional comonomer N‐hydroxyl‐methyl acrylamide (NMA) was conducted by batch emulsion copolymerization to modify the properties of polysiloxane. Morphology of graft copolymer particles was characterized by transmission electron microscopy. The effect of polymerization method, PHMS content, initiator concentration, and NMA content on stability of emulsion, morphology, size of particle, and rheological properties were investigated. It has been found that stability of emulsion is better by semicontinuous emulsion polymerization than that of batch emulsion polymerization and it increased with increasing PHMS‐NMA concentration. Increasing PHMS concentration and NMA concentration, the particle size and the viscosities increase. The property of resistance to electrolytes of graft copolymer emulsions and swelling property of film were also discussed. Results showed PHMS‐g‐P [butylacrylate (BA)‐N‐hydroxyl‐methyl acrylamide (NMA)] graft copolymer emulsion has good resistance to electrolytes and the water absorption of its film increases with increasing BA‐NMA content grafted onto PHMS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2209–2217, 1999     

Synthesis and application of a novel epoxy grafted thermosetting acrylic resin

A novel manufacturing process for high performance metallic can coating was carried out based on an epoxy‐grafted acrylic resin. Firstly, the epoxy resin was reacted with acrylic amide forming a ring opened product epoxy‐amide resin, and then the product obtained copolymerized with all other monomers, such as acrylic acid (AA), butyl acrylate (BA), hydroxypropyl acrylate (HPA), 2‐ethylhexyl acrylate (2‐EHA), methyl methacrylate (MMA), styrene (St), using free radical solvent polymerization in the presence of BPO. The resins prepared present the transparent appearance, and the target resin coating based on these resins exhibits excellent boiling resistance and chemicals resistance and can be applied as the protective coating for metallic can. The effects on the coating properties, such as amount of acrylic acid, 2‐EHA wt % between 2‐EHA and BA, amount of amino resin, amount of catalyst, and so forth, were investigated. In addition, the influences of polymerization time on the conversion ratio of monomers were also studied. Results show that under the optimal conditions, the target resin coating provides excellent physical and mechanical properties. The various properties tests for this coating have been performed in accordance with the standards of ASTM. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Resultant synergism in the shear resistance of acrylic pressure‐sensitive adhesives prepared by emulsion polymerization of n‐butyl acrylate/2‐ethyl hexyl acrylate/acrylic acid

Acrylic emulsion pressure‐sensitive adhesives (PSAs) were synthesized by the copolymerization of n‐butyl acrylate with various levels of 2‐ethyl hexyl acrylate (2EHA) and a small constant amount of acrylic acid. The effect of varying the n‐butyl acrylate/2EHA monomer composition on the kinetic behavior of the polymerization and the characteristics of the copolymers prepared in a batch process were investigated. The results showed that increasing the amount of 2EHA in the monomer caused the polymerization rate and the glass‐transition temperature of the acrylic copolymers to decrease. Increasing the amount of 2EHA caused the gel content of the copolymers to decrease, reaching a minimum at 50 wt %; thereafter, the gel content increased at higher 2EHA levels. For the acrylic emulsion, the peel‐fracture energy of the PSAs decreased as the amount of 2EHA in the monomer was increased up to 50 wt %. At higher 2EHA levels, the peel‐fracture energy was relatively constant. Interestingly, a synergistic effect of increased shear resistance at 25 wt % 2EHA was observed without a significant trade‐off in terms of the peel and tack properties. This behavior was attributed to a good interconnection between the microgels and the free polymer chains inside the contacting particles in the adhesive film. Cooperation between various levels of 2EHA in the copolymer structure simultaneously changed the crosslink molecular weight (M_c) of the microgels and the entanglement molecular weight (M_e) of the free chains in the adhesive network morphology. The adhesive performance of the PSAs was found to be correlated with their M_c/M_e values as the 2EHA proportion was varied. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of hemispherical poly(4‐vinylpyridine‐co‐butyl acrylate)/poly(styrene‐co‐butyl acrylate) composite microspheres by seeded preswelling emulsion polymerization

Seeded preswelling emulsion polymerization was carried out by using monodispersed poly(4‐vinylpyridine‐co‐butyl acrylate) [P(4VP‐BA)] particles as the seed, and styrene and butyl acrylate as the second‐stage monomers under different polymerization conditions, to obtain hemispherical polystyrene (PST)‐rich–P4VP‐rich microspheres. Prior to polymerization, toluene was added into the preswelling system together with the second‐stage monomers. It was found that, with the increase of the amount of toluene, the particle morphology showed a tendency toward desirable hemispherical structure, and the colloidal stability of composite latex was improved. When the weight ratio of toluene/seed latex was increased up to 7.5/40 (g/g), the stable hemispherical latex could be obtained. However, when toluene was not added, the coagulum formed on the wall of the reactor during polymerization, and the composite particles with multiple surface domains (such as sandwich‐like, popcorn‐like) were formed. In addition, the final morphology of composite particles was influenced by the polarity of the seed crosslinker and the hydrophilicity of the second‐stage initiator, which could affect the mobility of poly(styrene‐co‐butyl acrylate) [P(ST‐BA)] chains. The morphology development during the polymerization was investigated in detail, and a schematic model was derived to depict the formation mechanism of hemispherical P(4VP‐BA)/P(ST‐BA) composite microspheres. The results revealed that the mobility of the P(ST‐BA) chains influenced the diffusion of the P(ST‐BA) domains on the surface of the P(4VP‐BA) matrix. When the mobility of the P(ST‐BA) chains allowed small‐size P(ST‐BA) domains to coalesce into one larger domain, complete phase‐separated morphology (hemisphere) could be achieved. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3811–3821, 2003     

Studies on the polyblends of poly(vinyl chloride) with various methacrylate copolymers,melt rheological properties. II

Studies have been made on the melt rheological properties of poly(vinyl chloride) (PVC) with copolymers of methyl methacrylate (MMA) and methyl acrylate (MA), ethyl acrylate (EA), butyl acrylate (BA), and 2-ethyl hexyl acrylate (EHA) at a blending ratio of 80:20. Effect of blend composition on shear stress–shear rate, melt viscosity, melt elasticity, and extrudate distortion have been studied. A significant decrease in the melt viscosity is observed on incorporation of low T_g, acrylate copolymers such as those with BA and EHA, thereby reducing the processing temperature. First normal stress and die swell ratio also decreases with an increase in the side chains of acrylate copolymer. PVC blended with P(MMA-co-BA) and P(MMA-co-EHA) is sensitive to both temperature and shear stress.     

Study on synthesis and morphology control of poly(4‐vinylpyridine‐co‐butyl acrylate)/poly(styrene‐co‐butyl acrylate) composite microspheres

Monodispersed crosslinked cationic poly(4‐vinylpyridine‐co‐butyl acrylate) [P(4VP‐BA)] seed latexes were prepared by soapless emulsion polymerization, using 2,2′‐azobismethyl(propionamidine)dihydrochloride (V₅₀) as an initiator and divinylbenzene (DVB) or ethylene glycol dimethacrylate (EGDMA) as a crosslinker. The optimum condition to obtain monodispersed stable latex was investigated. It was found that the colloidal stability of the P4VP latex can be improved by adding an adequate amount of BA (BA/4VP = 1/4, w/w), and adopting a semicontinuous monomer feed mode. Subsequently, poly(4‐vinylpyridine‐co‐butyl acrylate)/Poly(styrene‐co‐butyl acrylate) [P(4VP‐BA)/P(ST‐BA)] composite microspheres were synthesized by seeded polymerization, using the above latex as a seed and a mixture of ST and BA as the second‐stage monomers. The effects of the type of crosslinker, the degree of crosslinking, and the initiators (AIBN and V₅₀) on the morphology of final composite particles are discussed in detail. It was found that P(4VP‐BA)/P(ST‐BA) composite microspheres were always surrounded by a PST‐rich shell when V₅₀ was used as initiator, while sandwich‐like or popcorn‐like composite particles were produced when AIBN was employed. This is because the polarity of the polymer chains with AIBN fragments is lower than for the polymer with V₅₀ fragments, hence leading to higher interfacial tension between the second‐stage PST‐rich polymer and the aqueous phase, and between PST‐rich polymer and P4VP‐rich seed polymer. As a result, the seed cannot be engulfed by the PST‐rich polymer. Furthermore, the decrease of T_g of the second‐stage polymer promoted phase separation between the seeds and the PST‐rich polymer: sandwich‐like particles formed more preferably than popcorn‐like particles. It is important knowledge that various morphologies different from PST‐rich core/P4VP‐rich shell morphology, can be obtained only by changing the initiator, considering P4VP is much more hydrophilic than PST. The zeta potential of composite particles initiated by AIBN in seeded polymerization shifted from a positive to a negative charge. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1190–1203, 2002     

Core–shell particles designed for toughening poly(vinyl chloride)

A novel core–shell modifier (MOD) made up of polystyrene and poly(butyl acrylate) (PBA) grafted on a crosslinked styrene‐co‐butadiene core was synthesized by emulsion polymerization. This modifier was used for enhancing effectively the impact ductility of poly(vinyl chloride) (PVC) without losing its transparency. The effects of the MOD on the properties of PVC/MOD blends were explored. It was found that the butyl acrylate (BA) content of the MOD was an important factor affecting the properties of PVC/MOD blends. The Izod impact strength of these blends reached 1200 J m^?1 when the MOD contained 40 wt% BA. The dispersion morphology of the MOD in the PVC matrix was investigated using transmission electron microscopy, with a uniform dispersion of the MOD with higher BA content being obtained. The toughening mechanism of PVC/MOD blends was also investigated. The presence of BA in the MOD enhanced the ductility of the PVC blends due to the increased amount of soft phase (PBA). The dispersion morphology indicated that the interfacial interaction between MOD particles and PVC matrix was improved due to the presence of PBA graft chain in the MOD. TEM of impact fracture samples showed that shear yielding of the PVC matrix and debonding of MOD particles were the major toughening mechanisms for the PVC/MOD blends. Copyright © 2010 Society of Chemical Industry     

Preparation and characterization of composite resin by vinyl chloride grafted onto poly(BA-EHA)/poly(MMA-St)

Crosslinked poly(butyl acrylate-co-2-ethylhexyl acrylate)/poly(methyl methacrylate-co-styrene) (ACR I) latex was synthesized by multi-stage emulsion polymerization. A series of grafting vinyl chloride (VC) composite latices were prepared by emulsion copolymerization in the presence of core-shell ACR I latex. The effects of ACR I amount and its core/shell ratio on particle diameters of the composite latices and mechanical properties of the prepared materials were investigated. The grafting efficiency (GE) of VC grafted onto ACR I increases with an increasing ACR I content. Transmission electron microscope (TEM) study indicates that ACR I latex particles have a regular core-shell structure obviously. However, when styrene content in the shell of ACR I is more than 70 percent of the shell by weight, ACR I latex particles have an irregular core-shell morphology like sandwich. The composite latex particles synthesized by core-shell ACR I latex grafting VC have a clear three-layered core-shell structure. Dynamic mechanical analysis (DMA) study reveals that the compatibility between ACR I and PVC is well improved. With increasing ACR I content, the loss peak in low temperature range for every composite sample becomes stronger and stronger and gradually shifts to a higher temperature. Scanning electron microscope (SEM) graphs showed that the fractured surface of the composite sample exhibited better toughness of the material. TEM graphs showed that ACR I was uniformly dispersed in the PVC matrix.     

Acrylate–vinylidene chloride copolymers derived from corresponding water‐borne latexes: Influence of acrylate units on their potential as heavy‐duty anticorrosive coating materials

A series of aqueous latexes with solid contents of 56%–59% were synthesized by binary emulsion copolymerization of vinylidene chloride (VDC) with an acrylate, namely methyl acrylate (MA), ethyl acrylate (EA), butyl acrylate (BA), hexyl acrylate (HA), or 2‐ethylhexyl acrylate (EHA). Differential scanning calorimetry (DSC) and Fourier‐transform infrared (FTIR) spectroscopy showed that the acrylate units with short ester side‐chains, such as MA and EA, made the copolymers hard and the crystallization tendency of their PVDC segments was reduced. Hydrophobic acrylates with relatively long ester groups, such as HA and EHA, gave flexible copolymers, and favored the crystallization of their PVDC segments. BA endowed the copolymers with medium flexibility and crystallization tendency. As coating materials, the copolymers bearing MA and EA adhered poorly to the tinplate before or after 100 hr of salt‐spray corrosion, whereas those bearing BA, HA, or EHA showed good adhesion to tinplate when they had little or no crystallinity. After 100 hr of salt‐spray corrosion, only BA–VDC80, containing 80% VDC, retained both excellent adhesion to metal and excellent barrier performance. Further study demonstrated that BA–VDC80 could protect tinplate from rusting for at least 250 hr under harsh salt‐spray corrosion. Scanning electron microscopy, FTIR‐attenuated total reflectance spectroscopy and DSC were used to evaluate the corroded BA–VDC80 film. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40192.     

Preparation and characterization of nano‐CaCO3 encapsulated with polyacrylic and its application in PVC toughness

The properties and morphology of nano‐calcium carbonate (nano‐CaCO₃) modified with the titanate coupling agent isopropyl trioleoyl titanate (IPTT) were characterized by Fourier transform infrared, thermogravimetric analyses, surface tension, and transmission electron microscopy. The results showed that the grafting ratio of IPTT on the surface of nano‐CaCO₃ (IPTT‐Ca) increased with IPTT content. IPTT‐Ca/PBA/PMMA (IPTT‐Ca/ACR, PBA/PMMA core‐shell polymer, referred to ACR) latexes were prepared by seeded emulsion polymerization. They were then used to mix with PVC resin. The outer layer (PMMA) enhanced the dispensability of IPTT‐Ca/ACR in the PVC matrix by increasing the interfacial interaction of these composite particles with PVC. The notched impact strengths of the blends were influenced by the weight ratio of IPTT‐Ca to BA/MMA monomers, the weight ratio of BA/MMA. The relationships between the mechanical properties and the core‐shell composite structures were elaborated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Properties and morphologies of PVC/nylon terpolymer blends

A new kind of blends of polyvinyl chloride (PVC)/nylon terpolymer was reported in this article. Two compatibilizers were used in this study: one is a terpolymer of ethylene–n‐butyl acrylate–monoxide (EnBACO); the other is terpolymer of EnBACO grafted with maleic anhydride (EnBACO‐g‐MAH). The observation of scanning electron microscope (SEM) reveals that the PVC/nylon terpolymer blends have a two‐phase structure; and the nylon terpolymer phase is the continuous phase, and PVC domains in the PVC/nylon terpolymer/EnBACO‐g‐MAH blends have fine dispersion over a broad range of the PVC/nylon terpolymer ratio. EnBACO‐g‐MAH is more compatible with the nylon terpolymer than EnBACO. EnBACO and EnBACO‐g‐MAH have different effects on the glass transition temperatures of the PVC phase and nylon terpolymer phase in the blends. The notched Izod impact strength, tensile strength, elongation at break, Vicat softening temperature (VST), and melt flow index (MFI) critically depend on PVC/nylon terpolymer ratio, the kinds and concentration of the compatibilizers. The PVC/nylon terpolymer/EnBACO‐g‐MAH blends display a good combination of high toughness, high flowability, and high VST under low load. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2823–2832, 2001     

Effect of 2‐ethylhexyl acrylate and N‐acryloylmorpholine on the properties of polyurethane/acrylic hybrid materials

A hybrid synthesis technology was used to prepare waterborne polyurethane/acrylic hybrid emulsions by polymerization of methyl methacrylate, butyl acrylate, 2‐ethylhexyl acrylate(EHA), and N‐acryloylmorpholine (AMCO) in presence of acrylic‐terminated PU dispersion. Various characterization methods were used to investigate the effect of EHA and ACMO content on the properties of the hybrid emulsions and their resultant films. The research results show that the introduction of EHA can enhance the elasticity of their films, meanwhile, ACMO endows the film with high gloss, adhesion on substrate, toughness, and hardness. Mixing the two monomers leads to yield the hybrid materials with moderate properties. While increasing the weight ratio of ACMO/EHA, the average particle size of the hybrid emulsions increases and their viscosity decreases. For the resultant films, their surface water contact angle, adhesion on substrates, tensile strength, and hardness increase, but the water resistance and elasticity decrease. It has been found that EHA and ACMO have a synergistic effect on gloss of the hybrid films and the hydrogen bond interaction increases with an increase in the ACMO content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41463.     

Poly(vinyl chloride)‐b‐poly(hydroxypropyl acrylate)‐b‐Poly(vinyl chloride): Understanding the synthesis of an amphiphilic PVC block copolymer on a pilot scale

The aim of this work was to develop an understanding of the major difficulties associated with the scale‐up of the technology for the synthesis of poly(vinyl chloride) (PVC) block copolymers that contain hydrophilic segments, thus providing important directions to be followed in order to produce such new materials on the industrial scale. The synthesis was carried out in a two‐step process. First, the macroinitiator α,ω‐di(iodo)poly(hydroxypropyl acrylate) was synthesized in an aqueous medium by (single electron transfer)/(degenerative chain transfer) living radical polymerization (SET‐DTRP) catalyzed by Na₂S₂O₄. The block copolymer was then prepared by SET‐DTRP of vinyl chloride (VC) from the iodine‐terminal active chain ends of the macroinitiator, thereby leading to the formation of the block copolymer poly(vinyl chloride)‐b‐poly(hydroxypropyl acrylate)‐b‐poly(vinyl chloride). This report covers important aspects related to the characterization of the block copolymer produced and to the identification of the major limitations that must be overcome in order to produce this new material on the industrial scale. The results clearly show the differences between the theoretical predictions and the block copolymer compositions obtained by using a suspension polymerization method, which is the most‐used polymerization process in the PVC industry. J. VINYL ADDIT. TECHNOL., 19:94–104, 2013. © 2013 Society of Plastics Engineers     

Processability and characterization of poly(vinyl chloride)‐b‐poly(n‐butyl acrylate)‐b‐poly(vinyl chloride) prepared by living radical polymerization of vinyl chloride. Comparison with a flexible commercial resin formulation prepared with PVC and dioctyl phthalate

This work reports the synthesis and processing of a new flexible material based on PVC produced by living radical polymerization. The synthesis was carried out in a two‐step process. In the first step the macroinitiator α, ω‐di(iodo)poly(butyl acrylate) [α, ω‐di(iodo)PBA] was synthesized in water by single electron transfer/degenerative chain transfer mediated living radical polymerization (SET‐DTLRP) catalyzed by Na₂S₂O₄. In the second step this macroinitiator was reinitiated by SET‐DTLRP of vinyl chloride (VC), thereby leading to the formation of the block copolymer poly(vinyl chloride)‐b‐poly(butyl acrylate)‐b‐poly(vinyl chloride) [PVC‐b‐PBA‐b‐PVC]. This new material was processed on a laboratory scale. The DMTA traces showed only a single glass transition temperature, thus indicating that no phase segregation was present. The copolymers were studied with regard to their processing, miscibility, and mechanical properties. The first comparison with commercial formulations made with PVC and dioctyl phthalate (DOP) is presented. J. VINYL ADDIT. TECHNOL., 12:156–165, 2006. © 2006 Society of Plastics Engineers     

Effect of nano‐SiO2 on granule characteristic and fusion process of Poly(vinyl chloride‐co‐vinyl acetate)/nano‐SiO2 composite resin

Poly(vinyl chloride‐co‐vinyl acetate) (PVVA)/nano‐SiO₂ composite resin was prepared by radical suspension polymerization of the monomers in the presence of fumed nano‐SiO₂ particles premodified with γ‐methylacryloxypropyl trimethoxysilane. The cool dioctyl phthalate absorption percentage, granule porosity, and specific surface area of the composite resin were enhanced through incorporation of nano‐SiO₂ into the PVVA. Scanning electron microscope pictures showed the resin had higher porosity. PVVA/nano‐SiO₂ composite resin was mixed with pure PVC resin to form a mixture sample (polymer‐composite blend [PCB]) and the mixture was fused in the torque rheometer. The rheological test results indicated that, at a certain nano‐SiO₂ content, the fusion speed of PCB was accelerated and the fusion temperature of PCB was decreased, owing to nano‐SiO₂ dispersed evenly in the polymer matrix. When excessive nano‐SiO₂ was loaded, the fusion torque, the fusion time, and the fusion temperature of PCB were all increased. These properties are correlative to the dispersive density of nano‐SiO₂ in the polymer matrix. This study also demonstrated that the introduction of small amounts of nano‐SiO₂ into the resin increased the impact strength and tensile strength of PCB simultaneously. J. VINYL ADDIT. TECHNOL., 20:230–236, 2014. © 2014 Society of Plastics Engineers     

Effect of 3‐aminopropyltriethoxysilane on properties of poly(butyl acrylate‐co‐maleic anhydride)/silica hybrid materials

The transparent poly(butyl acrylate‐co‐maleic anhydride)/silica [P(BA‐co‐MAn)/SiO₂] has been successfully prepared from butyl acrylate‐maleic anhydride copolymer P(BA‐co‐MAn) and tetraethoxysilane (TEOS) in the presence of 3‐aminopropyltriethoxysilane (APTES) by an in situ sol–gel process. Triethoxysilyl group can be readily incorporated into P(BA‐co‐MAn) as pendant side chains by the aminolysis of maleic anhydride unit of copolymer with APTES, and then organic polymer/silica hybrid materials with covalent bonds between two phases can be formed via the hydrolytic polycondensation of triethoxysilyl group‐functionalized polymer with TEOS. It was found that the amount of APTES could dramatically affect the gel time of sol–gel system, the sol fraction of resultant hybrid materials, and the thermal properties of hybrid materials obtained. The decomposition temperature of hybrid materials and the final residual weight of thermogravimetry of hybrid both increase with the increasing of APTES. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) showed that the morphology of hybrid materials prepared in the presence of APTES was a co‐continual phase structure. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 419–424, 1999