Surface modification of Cr2O3 nanoparticles with 3-amino propyl trimethoxy silane (APTMS). Part 1: Studying the mechanical properties of polyurethane/Cr2O3 nanocomposites

The surface of Cr₂O₃ nanoparticles was modified with various amounts of 3-amino propyl trimethoxy silane (APTMS). Thermal gravimetric analysis (TGA), turbidimeter and Fourier transform infrared (FTIR) spectroscopy were utilized in order to investigate APTMS grafting on the nanoparticles. Then, polyurethane nanocomposites were prepared using various loadings of silane modified Cr₂O₃ nanoparticles. The nanoparticles dispersion in the coating matrix was studied by a field emission scanning electron microscopy (FESEM). Dynamic mechanical thermal analysis (DMTA) and tensile test were utilized in order to investigate the mechanical properties of the nanocomposites. Results obtained from FTIR, TGA and turbidimeter measurements revealed that the organic functional groups of the silane were successfully grafted on the surface of the nanoparticles. The mechanical properties of the polyurethane were significantly enhanced using 2 wt% Cr₂O₃ nanoparticles modified with 0.43 g silane/5 g pigment compared with other samples.     

Tribological properties of Al2O3 nanoparticles as lubricating oil additives

Nano-scale Al₂O₃ spherical particles, prepared via a hydrothermal method and modified by silane coupling agent, can be well-dispersed in lubricating oil. The tribology properties of Al₂O₃ nanoparticles as lubricating oil additives have been studied by four-ball and thrust-ring friction test, which illustrate that the modified Al₂O₃ nanoparticles can effectively improve the lubricating behaviors compared to the base oil. When the added concentration is 0.1 wt%, the friction coefficient and the wear scar diameter are both smallest. The lubrication mechanism is that a self-laminating protective film is formed on the friction surface and the wear behavior changes from sliding friction to rolling friction.     

Synthesis of silver/SiO2/Eu:Lu2O3 core-shell nanoparticles and their polymer nanocomposites

We report a core-shell approach that combines silver nanoparticles as the metal core component with Eu:Lu₂O₃ as the phosphor shell component. The core-shell design contains an optically transparent SiO₂ intermediate layer that separates the metallic nanoparticle core and the phosphor shell. The thickness of the SiO₂ layer is in the nanometer range and can be tuned, so as to provide for different interactions between the core and shell. To demonstrate the versatility of the design, spherical silver nanoparticles or wavelength-tunable plasmonic silver nanoplates are used as the core component. In addition, a nanocomposite phosphor was fabricated by embedding the core-shell nanoparticles into a transparent polymeric matrix. The core-shell metal-phosphor design presented here serves as framework for the fabrication of inexpensive nanocomposite scintillator.     

Dynamic corrosion of Al2O3-ZrO2-SiO2 and Cr2O3-containing refractories by molten frits. Part I: Macroscopic analysis

Manufacturing of enamels and frits has undergone dramatic changes since the 1980s. This has required significant efforts in research and development. Typical compositions of frits for ceramic tiles are silica-based with fluxing agents; some of the components are highly corrosive. Improvements in the production of frits would imply the selection of the most adequate refractories as a function of the chemical composition of the considered frit and the fabrication procedure.The refractories currently used in frit furnaces are Al₂O₃-ZrO₂-SiO₂ (AZS) fused cast materials and Cr₂O₃-based materials. In this work, results on dynamic corrosion studies of AZS and Cr₂O₃-based materials by two ZnO-containing frits are described. Experiments have been performed using the “Merry Go Round” test at ≅1500 °C. Macroscopic results are analysed in terms of the remaining volume after the tests, as usually done in the glass industry. The significance and limits of such an approach are discussed.     

Dynamic corrosion of Al2O3-ZrO2-SiO2 and Cr2O3-containing refractories by molten frits. Part II: Microstructural study

In this work results on dynamic corrosion studies of fused cast Al₂O₃-SiO₂-ZrO₂ and isostatically pressed and sintered Cr₂O₃-based refractories by two crystalline (transparent) frits are described. Experiments have been performed using the “Merry Go Round” test at ≅1500 °C.Microstructural and mineralogical analyses of selected areas from the corroded regions of the studied refractories were performed by reflected light optical microscopy and scanning electron microscopy with analysis by X-ray dispersive energy.Significant differences between the corrosion mechanisms acting in the two types of materials were found. In the fused cast Al₂O₃-SiO₂-ZrO₂ specimens corrosion took place by the dissolution of alumina and zirconia in the frit and in the glass formed by the reaction between the frit and the refractory. In the Cr₂O₃-based materials the corrosion process was controlled by the capillar penetration of the molten frit through the open pores. The reaction between the ZnO from the frits and Cr₂O₃ led to the formation of spinel (ZnCr₂O₄), a high-melting point bonding phase that retarded the frit penetration. Results are discussed using the relevant phase equilibrium diagrams.     

Accommodation of impurities in α-Al2O3, α-Cr2O3 and α-Fe2O3

Atomic scale computer simulation was used to predict the mechanisms and energies associated with the accommodation of aliovalent and isovalent dopants in three host oxides with the corundum structure. Here we consider a much more extensive range of dopant ions than has previously been the case. This enables a rigorous comparison of calculated mechanism energetics. From this we predict that divalent ions are charge compensated by oxygen vacancies and tetravalent ions by cation vacancies over the full range of dopant radii. When defect associations are included in the model these conclusions remain valid. At equilibrium, defects resulting from extrinsic dopant solution dominate intrinsic processes, except for the largest dopant cations. Solution reaction energies increase markedly with increasing dopant radius. The behaviour of cluster binding energies is more complex.     

Mechanical properties of Al2O3-Cr2O3/Cr3C2 nanocomposite fabricated by spark plasma sintering

The fine grains of Al₂O₃-Cr₂O₃/Cr-carbide nanocomposites were prepared by employing recently developed spark plasma sintering (SPS) technique. The initial materials were fabricated by a metal organic chemical vapor deposition (MOCVD) process, in which Cr(CO)₆ was used as a precursor and Al₂O₃ powders as matrix in a spouted chamber. The basic mechanical properties like hardness, fracture strength and toughness, and the nanoindentation characterization of nanocomposites such as Elastics modulus (E), elastic work (W_e) and plastic work (W_p) were analyzed. The microstructure of dislocation, transgranular and step-wise fracture surface were observed in the nanocomposites. The nanocomposites show fracture toughness of (4.8 MPa m^1/2) and facture strength (780 MPa), which is higher than monolithic alumina. The strengthening mechanism from the secondary phase and solid solution are also discussed in the present work. Nanoindentation characterization further illustrates the strengthening of nanocomposites.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Effect of Y2O3 and Er2O3 co-dopants on phase stabilization of bismuth oxide

Bi₂O₃ compositions were prepared to investigate the effect of rare earth metal oxides as co-dopants on phase stability of bismuth oxide. Compositions containing 9-14 mol% of Y₂O₃ and Er₂O₃ were synthesized by solid state reaction. The structural characterization was carried out using X-ray powder diffraction. The XRD results show that the samples containing 12 and 14 mol% total dopants had cubic structure, whereas the samples with lower dopant concentrations were tetragonal. Comparing the lattice parameters of the cubic phases of (Bi₂O₃)_0.88(Y₂O₃)_0.06(Er₂O₃)_0.06 and (Bi₂O₃)_0.86(Y₂O₃)_0.07(Er₂O₃)_0.07 revealed that lattice parameter decreases by increasing the dopant concentration. The XRD pattern and the powder density results indicated the formation of solid solution in the studied systems. After annealing samples with cubic phase at 600 °C for various periods of time, phase transformation to tetragonal and rhombohedral occurs.     

XANES study of polyaniline-V2O5 and sulfonated polyaniline-V2O5 nanocomposites

In this work, two materials for secondary lithium battery cathodes formed by polyaniline-V₂O₅ and sulfonated polyaniline-V₂O₅, which have a higher charge capacity than the V₂O₅ xerogel, were synthesized. X-ray absorption and Fourier transform infrared spectroscopies were employed to analyze the short-range interactions in these materials. Based on these experiments, it was possible to observe significant differences in the symmetry of the VO₅ units, and this was attributed to the intimate contact between V₂O₅ and the polymers, and to some flexibility of the VO₅ square pyramids due to the low range order of the nanocomposites.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Characteristics and catalytic properties of Pt–Sn/Al2O3 nanoparticles synthesized by one-step flame spray pyrolysis in the dehydrogenation of propane

The Pt–Sn/Al₂O₃ catalysts with 0.3 wt% Pt and 0.5–1.5 wt% Sn loading were prepared by one-step flame spray pyrolysis (FSP). Unlike the catalysts prepared by conventional impregnation method, the FSP-derived catalysts were composed of single-crystalline γ-alumina particles with the as-prepared primary particle size of 10–18 nm and contained only large pores. The FSP catalysts exhibited superior catalytic activity and better stability than the ones made by impregnation in the dehydrogenation of propane, while they did not alter the selectivity to propylene (in all cases, propylene selectivity ≥96%). The presence of large pores in the flame-made catalysts not only facilitated diffusion of the reactants and products but could also lessen the amount of carbon deposited during reactions. As revealed by CO chemisorption, transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS), the metal particles appeared to be partially covered by the alumina matrix (Al–O) due to the simultaneous formation of particles during FSP synthesis. Such phenomena, however, were shown to result in the formation of active Pt–Sn ensembles for propane dehydrogenation as shown by higher turnover frequencies (TOFs).     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

Selective synthesis of mixed alcohols from syngas over catalyst Fe2O3/Al2O3 in slurry reactor

The Fe₂O₃/Al₂O₃ catalyst was studied to selectively synthesize mixed alcohols from syngas in a continuously stirred slurry reactor with the oxygenated solvent Polyethylene Glycol-400 (PEG-400). The selectivity of mixed alcohols in the products reached as high as 95 wt.% and the C₂₊ alcohols (mainly ethanol) was more than 40 wt.% in the total alcohol products at the reaction conditions of 250 °C, 3.0 MPa, H₂/CO = 2 and space velocity = 360 ml/g_cat h. The hydrogen temperature programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS) measurements of the catalyst confirmed that the FeO phase was responsible for the high selectivity to mixed alcohols in the process. And the oxygenated solvent PEG-400 was also necessary for the selective synthesis of mixed alcohols in the reaction system.     

Long-term degradation of Ta2O5-doped Bi2O3 systems

Bismuth oxide in δ-phase is a well-known high oxygen ion conductor and can be used as an electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFCs). 5-10 mol% Ta₂O₅ are doped into Bi₂O₃ to stabilize δ-phase by solid state reaction process. One Bi₂O₃ sample (7.5TSB) was stabilized by 7.5 mol% Ta₂O₅ and exhibited single phase δ-Bi₂O₃-like (type I) phase. Thermo-mechanical analyzer (TMA), X-ray diffractometry (XRD), AC impedance and high-resolution transmission electron microscopy (HRTEM) were used to characterize the properties. The results showed that holding at 800-850 °C for 1 h was the appropriate sintering conditions to get dense samples. Obvious conductivity degradation phenomenon was obtained by 1000 h long-term treatment at 650 °C due to the formation of α-Bi₂O₃ phase and Bi₃TaO₇, and 〈1 1 1〉 vacancy ordering in Bi₃TaO₇ structure.     

Laser machining of Al2O3-ZrO2 (3%Y2O3) eutectic composite

In this work we present the study of the interaction between NIR pulsed laser and Al₂O₃-ZrO₂ (3%Y₂O₃) eutectic composite. The effect produced by modifying the reference position as well as the working conditions and laser beam features has been studied when the samples are processed by means of pulse bursts.The samples were obtained by the laser floating zone technique using a CO₂ laser system. The laser machining was carried out with a Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-widths in the nanosecond range.Geometric dimensions, i.e. ablated depth, machined width and removed volume as well as ablation yield of the resulting holes have been studied. We have described and discussed the morphology, composition and microstructure of the processed samples.     

Laser stereolithography of ZrO2 toughened Al2O3

Ceramic laser stereolithography is a manufacturing process suitable candidate for the production of complex shape technical ceramics. The green ceramic is produced layer by layer through laser polymerisation of UV curable ceramic suspensions. A number of critical issues deserve attention: high solid loading and low viscosity of the suspensions, high UV reactivity, prevention of interlayer delamination in the green and in the sintered body, good mechanical performance. In this work, ZrO₂-reinforced Al₂O₃ components have been obtained from an acrylic modified zircon loaded with alumina powders. The zircon compound is effective as organic photoactivated resin and allows the dispersion of a high volume fraction of Al₂O₃ powder (up to 50 vol.%) while keeping viscosity at reasonable low values. The zircon compound also represents a liquid ceramic precursor that converts to oxide after burning out of the binder. Thank to the good dispersion of the alumina powder in the zircon acrylate, a uniform dispersion of ZrO₂ submicron particles is obtained after pyrolysis. These are located at the grain boundaries between alumina grains. Formation of both monoclinic and tetragonal ZrO₂ occurs as evidenced by XRD. No delamination occurs in bending tests as evidenced by SEM fractography, satisfactory modulus and strength values were concurrently found.     

Effects of sintering additives on dispersion properties of Al2O3 slurry containing polyacrylic acid dispersant

The effects of sintering aid adsorption on the dispersion properties of aluminum oxide slurries were investigated. We considered Al₂O₃ slurry without additives and Al₂O₃ slurry with a Mg additive with 0.1 mass% in oxide equivalent as a sintering aid. In this study, we evaluated the adsorption isotherm of polyacrylic acid (PAA) onto Al₂O₃ and the dispersion degree of Al₂O₃ slurries in sedimentation tests under gravity. The adsorption isotherm featured a characteristic adsorption isothermal line with a maximum value when Mg additive was present in Al₂O₃. In addition, the packing fractions did not correspond to the apparent viscosity. However, in slurry that was allowed to settle for several days, both of them agreed.Therefore, the disagreement between the packing fraction and the apparent viscosity immediately after preparation arose from changes of the dispersion state, such as the decrease of the distance between particles with time.     

Investigation of surface modification of rutile TiO2 nanoparticles with SiO2/Al2O3 on the properties of polyacrylic composite coating

Surface modification and characterization of TiO₂ nanoparticles as an additive in a polyacrylic clear coating were investigated. For the improvement of nanoparticles dispersion and the decreasing of photocatalytic activity, the surface of nanoparticles was modified with binary SiO₂/Al₂O₃. The surface treatment of TiO₂ nanoparticles was characterized with FTIR. Microstructural analysis was done by AFM. The size, particle size distribution and zeta potential of TiO₂ nanoparticles in water dispersion was measured by DLS method. For the evaluation of particle size and the stability of nanoparticles in water dispersions with higher solid content the electroacoustic spectroscopy was made. To determine the applicability and evaluate the transmittance of the nano-TiO₂ composite coatings UV–VIS spectroscopy in the wavelength range of 200–800 nm was employed. The results showed that surface treatment of TiO₂ nanoparticles with SiO₂/Al₂O₃ improves nanoparticles dispersion and UV protection of the clear polyacrylic composite coating.