Preparation and characterization of CuIn1 − xGaxSe2 − ySy thin film solar cells by rapid thermal processing

This paper describes the synthesis and characterization of CuIn_1 − xGa_xSe_2 − yS_y (CIGSeS) thin-film solar cells prepared by rapid thermal processing (RTP). An efficiency of 12.78% has been achieved on ~ 2 µm thick absorber. Materials characterization of these films was done by SEM, EDS, XRD, and AES. J-V curves were obtained at different temperatures. It was found that the open circuit voltage increases as temperature decreases while the short circuit current stays constant. Dependence of the open circuit voltage and fill factor on temperature has been estimated. Bandgap value calculated from the intercept of the linear extrapolation was 1.1-1.2 eV. Capacitance-voltage analysis gave a carrier density of 4.0 × 10¹⁵ cm^− 3.     

Simulations of Si and SiO2 etching in SF6 + O2 plasma

Chemical etching of Si and SiO₂ in SF₆ + O₂ plasma is considered. The concentrations of plasma components are calculated using values extrapolated from experimental data. Resulting calculations of plasma components are used for the calculation of Si and SiO₂ etching rates. It is found that the reaction constants for reactions of F atoms with Si atoms and SiO₂ molecules are equal to (3.5 ± 0.1) × 10⁻² and (3.0 ± 0.1) × 10⁻⁴, respectively. The influence of O₂ addition to SF₆ plasma on the etching rate of Si is quantified.     

Preparation and thermoelectric properties of nc-Si:(Al2O3 + SiO2) composite film

A composite film of nanocrystalline Si (nc-Si) embedded in (Al₂O₃ + SiO₂) has been prepared on a quartz substrate by thermally evaporating a 400 nm thick Al film on a quartz substrate and annealing in air at 580 °C for 1 h. During annealing, the Al reacts with the SiO₂ of the quartz substrate and produces nc-Si, which is embedded in the (Al₂O₃ + SiO₂) film. The average size of nc-Si is ~ 22 nm and the thickness of the nc-Si:(Al₂O₃ + SiO₂) composite film is ~ 810 nm. It is found that the prepared film is thermoelectric with a Seebeck coefficient of − 624 μV/K at 293 K and − 225 μV/K at 413 K.     

Growth and vacuum post-annealing effect on the properties of the new absorber CuSbS2 thin films

Post-growth treatments in vacuum atmosphere were performed on CuSbS₂ films prepared by the single-source thermal evaporation method on glass substrates. The films were annealed in vacuum atmosphere for 2 h in temperature range 130-200 °C. The effect of this thermal treatment on the structural, optical and electrical properties of the films was studied. X-ray diffraction (XRD) patterns indicated that the films exhibited an amorphous structure for annealing temperature below 200 °C and a polycrystalline structure with CuSbS₂ principal phase. For the films annealed at temperatures below 200 °C one direct optical transition in range 1.8-2 eV was found. For the films annealed at 200 °C, two optical direct transitions emerged at 1.3 and 1.79 eV corresponding to the CuSbS₂ and Sb₂S₃ values respectively. The electrical measurements showed a conversion from low resistivities (3.10^− 2-9.10^− 2) Ω cm for the samples annealed at temperatures below 200 °C to relatively high resistivities (2 Ω cm) for the samples annealed at 200 °C. In all cases the samples exhibited p-Ztype conductivity.     

Enhancing the oxygen permeability of Ba0.5Sr0.5Co0.8Fe0.2O5 + δ membranes by coating RBaCo2O5 + δ(R= Pr, Nd, Sm, Gd) layers

The effects of a thin RBaCo₂O_5 + δ (R= Pr, Nd, Sm, Gd) layer coating on the oxygen permeation flux through Ba_0.5Sr_0.5Co_0.8Fe_0.2O_5 + δ(BSCF) membrane were investigated. Due to the high oxygen adsorption and desorption rate constants k_a and k_d of the RBaCo₂O_5 + δ (R112) materials and the porous structure of the coating layers, the oxygen permeation flux through the BSCF membranes can be enhanced remarkably. It was found that the reaction between Pr112 and BSCF also has significant influence on the oxygen permeation flux. The reaction between Pr112 and BSCF forms impurities which may block oxygen permeation flux. However, Nd112, Sm112, and Gd112 do not react seriously with BSCF, therefore, coating layers of these materials can significantly enhance the oxygen permeation flux of BSCF membranes.     

Characteristics of stacked CuInS2 and CuGaS2 layers as determined by the growth sequence

CuInS₂ and CuGaS₂ thin films have been prepared sequentially from elemental evaporation sources onto conventional soda lime glass substrates heated at 350 °C during the deposition process. The gradient in the structure and composition of the stacked layers has been investigated for the two possible growth sequences. Structural depth profiling and crystallographic phase analysis were performed by grazing incidence X-ray diffraction. The atomic distribution in the films depth was analyzed by X-ray photoelectron spectroscopy combined with sputter etching. Formation of the quaternary compound CuIn_1 − xGa_xS₂, with a high Ga content x > 0.80, has been detected with different distribution depending on the growth sequence.     

Instantaneous preparation of CuIn(S1 − x, Sex)2 films by means of sparks using microwave irradiation

CuIn(S_1 − x,Se_x)₂ (CISSe) films aimed at flexible solar cells were directly prepared on Ti foils from elemental In, Cu, S, and Se particle precursor using microwave irradiation. The formation of the CISSe phase was deduced from X-ray diffraction (XRD) patterns. The (112) peaks of CISSe were well defined and the lattice constants increased in direct proportion to the S/(S + Se) ratio almost satisfying Vegard's law. In particular, CuInSe₂ was formed in the desired chalcopyrite lattice as indicated by the presence of (101), (103) and (211) peaks in the XRD pattern. Porous surfaces and formation of by-products were avoided by employing an evaporated In and Cu films instead of In and Cu particles.     

Effect of Pb(Zn1 / 2W1 / 2)O3 introduction on perovskite development and dielectric properties of (Ba,Pb)TiO3

Powders of a Pb(Zn_1 / 2W_1 / 2)O₃-introduced BaTiO₃-PbTiO₃ system were prepared. A two-step calcination route of a B-site precursor method was employed to promote perovskite formation. The overall effects of the Pb(Zn_1 / 2W_1 / 2)O₃ incorporation on changes in crystalline aspects as well as dielectric properties were explored.     

Tl2Ba2CaCu2O8 thin films on 2 in. LaAlO3(0 0 1) substrates

High quality Tl₂Ba₂CaCu₂O₈ (Tl-2212) superconducting thin films are prepared on both sides of 2 in. LaAlO₃(0 0 1) substrates by off-axis magnetron sputtering and post-annealing process. XRD measurements show that these films possess pure Tl-2212 phase with C-axis perpendicular to the substrate surface. The thickness unhomogeneity of the whole film on the 2 in. wafer is less than 5%. The superconducting transition temperatures T_cs of the films are around 105 K. At zero applied magnetic field, the critical current densities J_cs of the films on both sides of the wafer were measured to be above 2 × 10⁶ A/cm² at 77 K. The microwave surface resistance R_s of film was as low as 350 μΩ at 10 GHz and 77 K. In order to test the suitability of Tl-2212 thin films for passive microwave devices, 3-pole bandpass filters have been fabricated from double-sided Tl-2212 films on LaAlO₃ substrates.     

Study of flash evaporated CuIn1 − xGaxTe2 (x = 0, 0.5 and 1) thin films

CuIn_1 − xGa_xTe₂ thin films with x = 0, 0.5 and 1, have been prepared by flash evaporation technique. These semiconducting layers present a chalcopyrite structure. The optical measurements have been carried out in the wavelength range 200-3000 nm. The linear dependence of the lattice parameters as a function of Ga content obeying Vegard's law was observed. The films have high absorption coefficients (4 · 10⁴ cm^− 1) and optical band gaps ranging from 1.06 eV for CuInTe₂ to 1.21 eV for CuGaTe₂. The fundamental transition energies of the CuIn_1 − xGa_xTe₂ thin films can be fitted by a parabolic equation namely E_g1(x) = 1.06 + 0.237x − 0.082x². The second transition energies of the CuInTe₂ and CuGaTe₂ films were estimated to be: E_g2 = 1.21 eV and E_g2 = 1.39 eV respectively. This variation of the energy gap with x has allowed the achievement of absorber layers with large gaps.     

Structure and thermal conductivity of Gd2(TixZr1 − x)2O7 ceramics

The Gd₂(Ti_xZr_1 − x)₂O₇ (x = 0, 0.25, 0.50, 0.75, 1.00) ceramics were synthesized by solid state reaction at 1650 °C for 10 h in air. The relative density and structure of Gd₂(Ti_xZr_1 − x)₂O₇ were analyzed by the Archimedes method and X-ray diffraction. The thermal diffusivity of Gd₂(Ti_xZr_1 − x)₂O₇ from room temperature to 1400 °C was measured by a laser-flash method. The Gd₂Zr₂O₇ has a defect fluorite-type structure; however, Gd₂(Ti_xZr_1 − x)₂O₇ (0.25 ≤ x ≤ 1.00) compositions exhibit an ordered pyrochlore-type structure. Gd₂Zr₂O₇ and Gd₂Ti₂O₇ are infinitely soluable. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ increases with increasing Ti content under identical temperature conditions. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ first decreases gradually with the increase of temperature below 1000 °C and then increases slightly above 1000 °C. The thermal conductivity of Gd₂(Ti_xZr_1 − x)₂O₇ is within the range of 1.33 to 2.86 W m^− 1 K^− 1 from room temperature to 1400 °C.     

Luminescence excitation spectra of TbX3 (X = Cl, Br, I)

A systematic study of the excitation spectrum of TbX₃ (X = Cl⁻, Br⁻, I⁻) is presented in this work. In general, the excitation spectra of TbX₃ can be divided into three major regions: (1) the short-wave host lattice absorption region, (2) the intermediate absorption region where the Tb³⁺ 4f⁸ → 4f⁷5d¹ interconfigurational excitation transition are located, and (3) the long-wave excitation region where the Tb³⁺ 4f⁸ → 4f⁸ intraconfigurational excitation transition are located. The high spin and the low spin components of the Tb³⁺ interconfigurational excitation transition are clearly identified in the case of TbCl₃. The luminescence of TbX₃ (X = Cl⁻, Br⁻, I⁻) is dominated by emission transitions emanating from the Tb³⁺⁵D₄ state. A comparative study of the optical properties of TbX₃ (X = Cl⁻, Br⁻, I⁻) with the properties of the Tb³⁺ ion in several halide host lattices is presented. Further, a comparative study of the fundamental host lattice optical transitions in terbium halides and other halide materials is also presented.     

Photoluminescence and Raman study of Cu2ZnSn(SexS1 − x)4 monograins for photovoltaic applications

The quaternary semiconductors Cu₂ZnSnSe₄ and Cu₂ZnSnS₄ have attracted a lot of attention as possible absorber materials for solar cells due to their direct bandgap and high absorption coefficient (> 10⁴ cm⁻¹). In this study we investigate the optical properties of Cu₂ZnSn(Se_xS_1 − x)₄ monograin powders that were synthesized from binary compounds in the liquid phase of potassium iodide (KI) flux materials in evacuated quartz ampoules. Radiative recombination processes in Cu₂ZnSn(Se_xS_1 − x)₄ monograins were studied by using low-temperature photoluminescence (PL) spectroscopy. A continuous shift from 1.3 eV to 0.95 eV of the PL emission peak position with increasing Se concentration was observed indicating the narrowing of the bandgap of the solid solutions. Recombination mechanisms responsible for the PL emission are discussed. Vibrational properties of Cu₂ZnSn(Se_xS_1 − x)₄ monograins were studied by using micro-Raman spectroscopy. The frequencies of the optical modes in the given materials were detected and the bimodal behaviour of the A₁ Raman modes of Cu₂ZnSnSe₄ and Cu₂ZnSnS₄ is established.     

Electrical properties of lead-free thick film NTC thermistors based on perovskite-type BaCoxCo2xBi1 − 3xO3

Lead-free thick film negative temperature coefficient (NTC) thermistors based on perovskite-type BaCo^II_xCo^III_2xBi_1 − 3xO₃ (x ≤ 0.1) were prepared by mature screen-printing technology. The microstructures of the thick films sintered at 720 °C were examined by X-ray diffraction and scanning electron microscopy. The electrical properties were analyzed by measuring the resistance-temperature characteristics. For the BaBiO₃ thick films, the room-temperature resistivity is 0.22 MΩ cm, while the room-temperature resistivity is sharply decreased to about 3 Ω cm by replacing of Bi with a small amount of Co. For compositions 0.02 ≤ x ≤ 0.1, the values of room-temperature resistivity (ρ₂₃), thermistor constant (B_25/85) and activation energy are in the range of 1.995-2.975 Ω cm, 1140-1234 K and 0.102-0.111 eV, respectively.     

Ar assisted carbidization of TiO2 (1 1 0) supported Mo nanoparticles by decomposition of C2H4

Ar⁺ assisted carbidization of Mo nanoparticles supported on TiO₂ (1 1 0) is studied by scanning tunneling microscopy (STM) and X-ray photoelectron spectroscopy (XPS). In order to activate the diffusion of carbon into the bulk of Mo nanoparticles we applied Ar ions (1 keV) during the exposure of C₂H₄. XPS exhibited that the decomposition of C₂H₄ at 850 K accompanied by ion bombardment results in an almost complete carbidization of nanocrystalline Mo while this treatment performed without ion bombardment results only in the carbidization of the particle surface. The modification of the crystallinity of the Mo-carbide particles was deduced from STM measurements.     

Optical and electrical properties of vapour phase grown Zn1 − xCrxTe crystals

The optical and electrical properties of vapour phase grown crystals of diluted magnetic semiconductor Zn_1 − xCr_xTe were investigated for 0 ≤ x ≤ 0.005. The diffuse reflectance spectra exhibited an increase in the fundamental absorption edge (E₀) with composition x and were also dominated by a broad absorption band around 5200 cm^− 1 arising from ⁵T₂ → ⁵E transition. The ⁵T₂ and ⁵E levels originate from the crystal field splitting of the ⁵D free ion in the ground state. The electrical resistivity measurements revealed semiconducting behaviour of the samples with p-type conductivity in the temperature range of 200-450 K.     

CuIn1 − xAlxSe2 thin films obtained by selenization of evaporated metallic precursor layers

CuIn_1 − xAl_xSe₂ (CIAS) thin films were grown by a two stage process. Cu, In and Al layers were sequentially evaporated and subsequently heated with elemental selenium in a quasi-closed graphite box. Different x values (0 ≤ x ≤ 0.6) were obtained by varying the Al and In precursor layers thicknesses. Selenization conditions such as Se amount provided during the selenization process were adjusted in order to optimize the film properties. Polycrystalline CuIn_1 − xAl_xSe₂ thin films with chalcopyrite structure were obtained. Referred to CuInSe₂ thin films the lattice parameters, the (112) orientation and the average crystallite size decreased and the band gap energy increased with increasing Al content. To optimize structural properties of the CIAS films a higher Se amount was required as the x value increased. The incorporation of Al changed the thin film morphology towards smaller grain sizes and less compact structures.     

Structural, electrical and optical properties of transparent Zn1 − xMgxO nanocomposite thin films

Zn_1 − xMg_xO thin films of various Mg compositions were deposited on quartz substrates using inexpensive ultrasonic spray pyrolysis technique. The influence of varying Mg composition and substrate temperature on structural, electrical and optical properties of Zn_1 − xMg_xO films were systematically investigated. The structural transition from hexagonal to cubic phase has been observed for Mg content greater than 70 mol%. AFM images of the Zn_1 − xMg_xO films (x = 0.3) deposited at optimized substrate temperature clearly reveals the formation of nanorods of hexagonal Zn_1 − xMg_xO. The variation of the cation-anion bond length to Mg content shows that the lattice constant of the hexagonal Zn_1 − xMg_xO decreases with corresponding increase in Mg content, which result in structure gradually deviating from wurtzite structure. The tuning of the band gap was obtained from 3.58 to 6.16 eV with corresponding increase in Mg content. The photoluminescence results also revealed the shift in ultraviolet peak position towards the higher energy side.     

Microstructure tuning of epitaxial BaTiO3 − x thin films grown using laser molecular-beam epitaxy by varying the oxygen pressure

Microstructural properties are found to be variant in the BaTiO_3 − x films grown on SrTiO₃(001) substrate under various oxygen pressures from 2 × 10^− 2 Pa to 2 × 10^− 5 Pa by laser molecular-beam epitaxy. Transmission electron microscopic studies reveal that the predominant defects in the films change from threading dislocations into (111) planar defects (i.e. stacking faults and nanotwins) by lowering the oxygen pressure. High density of these defects was observed in the BaTiO_3 − x film prepared at the oxygen pressure of 2 × 10^− 5 Pa, which shows metallic behavior. The relationships between oxygen pressure, microstructure, and electrical properties are established on the basis of oxygen deficiency. The formation of nanotwins in highly oxygen-deficient BaTiO_3 − x epitaxial thin films results from accommodating excess oxygen vacancies induced by lowering oxygen pressure.     

Enhanced ferromagnetic properties of multiferroic BiCoxFe1 − xO3 synthesized by hydrothermal method

The BiCo_xFe_1 − xO₃ samples have been successfully synthesized by hydrothermal process. The resulting products were characterized by X-ray powder diffraction (XRD), energy dispersive X-ray (EDS), differential thermal analysis (DTA), and physical property measurement system (PPMS).It was found that the magnetization of the obtained products was greatly enhanced by Co substituting for Fe ions. Furthermore, the value of magnetism of BiCo_xFe_1 − xO₃ samples can be adjusted by Fe doping concentration. DTA curve indicates the ferroelectric properties of the obtained BCFO samples are not affected by Co substitution. Therefore, it would be interesting to realize thin films with similar compositions and study their properties in the interest of device applications.