首届中国清洁技术投融资峰会在北京举行

随着中国经济的飞速发展,能源短缺,环境污染等问题日益严重.欧美等发达国家早已开始着手解决这些问题,每年都有大量来自于政府、企业和风险投资的资金用于清洁技术的研究与应用.根据道琼斯数据显示,2007年在清洁技术领域,全球共发生了221项投资案例,投资总额达30亿美元,比2006年增长了43%.     

中国科技部长万钢获国际氢能大奖

第十七届世界国际氢能大会于2008年6月15日～19日在澳大利亚布里斯班市举行,来自全世界44个国家的600余位代表聚集一堂,讨论当代氧能技术和发展趋势.     

Experimental Investigation on the Adiabatic Film Effectiveness for Counter-Inclined Simple and Laid-Back Film-Holes of Leading Edge

The adiabatic film effectiveness η of the counter-inclined film-holes fed by varying internal coolant intake on the turbine vane leading edge model was experimentally investigated. A semi-cylinder model was adopted to model the vane leading edge which was arranged with two-row holes, which located at ±15° on both sides. The four Leading edge model with the combinations of hole-shape(simple holes and laid-back holes) and intake structure(plenum and impingement) were tested under four blowing rati...     

国家发展改革委、财政部、国家电监会要求各地限期全面落实差别电价政策

经国务院批准,国家发展改革委、财政部、国家电监会近日联合下发了《关于进一步贯彻落实差别电价政策有关问题的通知》(以下简称《通知》),要求各地限期全面落实差别电价政策.     

热泵辅助太阳能中央热水系统年运行特性研究

提出采用热泵来取代传统的电加热器,构成热泵辅助太阳能中央热水系统,可有效地降低能源消耗.结合2005年西安地区气象数据,建立了合适的数学模型,并用现有的试验数据对模型进行了校准,通过模型模拟了该年热泵辅助和电辅助太阳能中央热水系统的性能系数,输入功耗,出水温度等运行参数,并对两者进行了对比.     

第二讲认识太阳利用太阳

一、太阳与太阳能 众所周知,在浩翰的宇宙中有一颗离我们最近的恒星--太阳.现代科学表明太阳距离我们相当遥远,达到1.5亿km,虽然太阳光的传播速度为30万km/s,但我们在地球上所见到的光线已经是8min之前从太阳发出的光线了.太阳的直径为139万km,而地球直径仅为1.27万km,太阳的直径约为地球直径的109倍,其体积则比地球大130多万倍.尽管如此,由于距离遥远,太阳张角仅仅为32′.     

Numerical Study of Convective and Radiation Heat Transfer Characteristics in an Upward-Facing Cylindrical Cavity under Back-Side Windy Condition

Under the back-side windy condition,the convection and radiation heat transfer characteristics in an iso-flux upward-facing cylindrical cavity were studied by three-dimensional numerical simulation.The impacts of cavity tilt angle,wind incident angle and wind speed on convection and radiation heat transfer Nusselt number Nuc and Nur were analyzed,and the possible explanations for their impacts were presented.Results show that due to the disturbance of wind,the influence of cavity tilt angle becomes more complicated and is related to wind incident angle and wind speed.The variation of Nuc or Nur with wind incident angle is different for different cavity tilt angles.Despite of the changes of cavity tilt angle or wind incident angle,the Nuc increases with the wind speed while the Nur presents a declination with the increasing of wind speed.Hence,compared with cavity tilt angle and wind incident angle,wind speed may be the dominant factor affecting or controlling the convective and radiation heat transfer of cavity.     

太阳能干燥系列讲座(1)太阳能干燥——太阳能热利用中不可忽视的领域

一物料干燥的能耗与环境污染 干燥作业涉及国民经济的广泛领域,是许多行业不可缺少的工序.在粮食、食品、果品、药材、木材、皮革、橡胶和陶瓷等许多产品的加工处理过程中,干燥作业对产品的质量和成本影响很大.     

担当

<正>6月30日,当中国政府将《强化应对气候变化行动——中国国家自主贡献》提交给联合国气候变化框架公约秘书处后,全世界都为中国的决定而侧目。中国设定了一个宏大的减排目标,振奋了各国应对气候变暖的神经。潘基文在声明中称赞中国提出的方案为在巴黎气候变化大会上增加动力、增强互信起到了积极推动作用;联合国秘书长副发言人哈克表示,中国提交自主贡献文件,为巴黎气候大会达成新的气候变化协议注入了动力,     

户用小型风力发电系统现状与发展(上)

<中华人民共和国可再生能源法>已于2005年2月28日在全国人大第11届第14次会议上通过,并将于2006年1月1日起施行,该法的颁布和实施,给小型风力发电行业的发展带来希望和光明,也必将大大促进农村能源的发展,户用风力发电产业也将会更上一层楼,前景看好.     

Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest

Woody biomass in Finland and Sweden comprises mainly four wood species: spruce, pine, birch and aspen. To study the ash, which may cause problems for the combustion device, one tree of each species were cut down and prepared for comparisons with fuel samples. Well-defined samples of wood, bark and foliage were analyzed on 11 ash-forming elements: Si, Al, Fe, Ca, Mg, Mn, Na, K, P, S and Cl. The ash content in the wood tissues (0.2–0.7%) was low compared to the ash content in the bark tissues (1.9–6.4%) and the foliage (2.4–7.7%). The woods’ content of ash-forming elements was consequently low; the highest contents were of Ca (410–1340 ppm) and K (200–1310), followed by Mg (70–290), Mn (15–240) and P (0–350). Present in the wood was also Si (50–190), S (50–200) and Cl (30–110). The bark tissues showed much higher element contents; Ca (4800–19,100 ppm) and K (1600–6400) were the dominating elements, followed by Mg (210–2400), P (210–1200), Mn (110–1100) and S (310–750), but the Cl contents (40–330) were only moderately higher in the bark than in the wood. The young foliage (shoots and deciduous leaves) had the highest K (7100–25,000 ppm), P (1600–5300) and S (1100–2600) contents of all tissues, while the shoots of spruce had the highest Cl contents (820–1360) and its needles the highest Si content (5000–11,300). This paper presented a new approach in fuel characterization: the method excludes the presence of impurities, and focus on different categories of plant tissues. This made it possible to discuss the contents of ash element in a wide spectrum of fuel-types, which are of large importance for the energy production in Finland and Sweden.     

NEXT GENERATION ENGINEERED MATERIALS FOR ULTRA SUPERCRITICAL STEAM TURBINES

正1 ABSTRACT To reduce the effect of global warming on our climate,the levels of CO2emissions should be reduced.One way to do this is to increase the efficiency of electricity production from fossil fuels.This will in turn reduce the amount of CO2emissions for a given power output.Using US practice for efficiency calculations,then a move from a typical US plant running at 37%efficiency to a 760℃/38.5 MPa(1 400/5 580 psi)plant running at 48%efficiency would reduce CO2emissions by 170kg/MW.hr or 25%.     

Aerodynamic performance effects of leading-edge geometry in gas-turbine blades

The purpose of this paper is to illustrate the advantages of the direct surface-curvature distribution blade-design method, originally proposed by Korakianitis, for the leading-edge design of turbine blades, and by extension for other types of airfoil shapes. The leading edge shape is critical in the blade design process, and it is quite difficult to completely control with inverse, semi-inverse or other direct-design methods. The blade-design method is briefly reviewed, and then the effort is concentrated on smoothly blending the leading edge shape (circle or ellipse, etc.) with the main part of the blade surface, in a manner that avoids leading-edge flow-disturbance and flow-separation regions. Specifically in the leading edge region we return to the second-order (parabolic) construction line coupled with a revised smoothing equation between the leading-edge shape and the main part of the blade. The Hodson–Dominy blade has been used as an example to show the ability of this blade-design method to remove leading-edge separation bubbles in gas turbine blades and other airfoil shapes that have very sharp changes in curvature near the leading edge. An additional gas turbine blade example has been used to illustrate the ability of this method to design leading edge shapes that avoid leading-edge separation bubbles at off-design conditions. This gas turbine blade example has inlet flow angle 0°, outlet flow angle −64.3°, and tangential lift coefficient 1.045, in a region of parameters where the leading edge shape is critical for the overall blade performance. Computed results at incidences of −10°,   −5°,   +5°,   +10° are used to illustrate the complete removal of leading edge flow-disturbance regions, thus minimizing the possibility of leading-edge separation bubbles, while concurrently minimizing the stagnation pressure drop from inlet to outlet. These results using two difficult example cases of leading edge geometries illustrate the superiority and utility of this blade-design method when compared with other direct or inverse blade-design methods.     

Hydrogen production by steam-gasification of carbonaceous materials using concentrated solar energy – V. Reactor modeling,optimization, and scale-up

A chemical reactor for the steam-gasification of carbonaceous particles (e.g. coal, coke) is considered for using concentrated solar radiation as the energy source of high-temperature process heat. A two-phase reactor model that couples radiative, convective, and conductive heat transfer to the chemical kinetics is applied to optimize the reactor geometrical configuration and operational parameters (feedstock's initial particle size, feeding rates, and solar power input) for maximum reaction extent and solar-to-chemical energy conversion efficiency of a 5 kW prototype reactor and its scale-up to 300 kW. For the 300 kW reactor, complete reaction extent is predicted for an initial feedstock particle size up to 35 μm at residence times of less than 10 s and peak temperatures of 1818 K, yielding high-quality syngas with a calorific content that has been solar-upgraded by 19% over that of the petcoke gasified.     

Contents in Volume 23,2014

<正>~~     

汽轮机数字电液调节系统挂闸异常的技术完善

分析了200MW汽轮机数字电液调节系统在运行中存在的挂闸异常问题,采取了相应的技术处理措施,且运行实践效果良好。     

新型高压共轨ECU升压模块的数字化开发与优化

为了提高喷油器电磁阀的响应速率,提出了一种基于CPLD(复杂可编程逻辑器件)应用于高压共轨ECU的数字升压模块。鉴于该升压电路结构参数多,其升压电压的恢复响应要求高等特征,基于Pspice建立了升压电路的仿真模型,研究了不同电路参数下升压模块的输出特性,全面优化了该升压模块的性能。结果显示,该升压模块的最大转换效率可以达90%以上。在柴油发动机上对ECU的试验表明,升压电压最大波动不超过10%,其恢复时间仅为1.3ms,功率管最大温升仅为41℃,满足整机运行范围内ECU的需求。     

Trace metal chemistry and silicification of microorganisms in geothermal sinter, Taupo Volcanic Zone, New Zealand

As part of a pilot study investigating the role of microorganisms in the immobilisation of As, Sb, B, Tl and Hg, the inorganic geochemistry of seven different active sinter deposits and their contact fluids were characterised. A comprehensive series of sequential extractions for a suite of trace elements was carried out on siliceous sinter and a mixed silica-carbonate sinter. The extractions showed whether metals were loosely exchangeable or bound to carbonate, oxide, organic or crystalline fractions. Hyperthermophilic microbial communities associated with sinters deposited from high temperature (92–94°C) fluids at a variety of geothermal sources were investigated using SEM. The rapidity and style of silicification of the hyperthermophiles can be correlated with the dissolved silica content of the fluid. Although high concentrations of Hg and Tl were found associated with the organic fraction of the sinters, there was no evidence to suggest that any of the heavy metals were associated preferentially with the hyperthermophiles at the high temperature (92–94°C) ends of the terrestrial thermal spring ecosystems studied.     

Assessment methods of material ageing using Sdobyrev''s creep rupture model

The physical aspects of the activation energy, in higher and high temperatures, of the metal creep process were examined. The research results of creep-rupture in a uniaxial stress state and the criterion of creep-rupture in biaxial stress states, at two temperatures, are then presented. For these studies creep-rupture, taking case iron as an example the energy and pseudoenergy activation was determined. For complex stress states the criterion of creep-rupture was taken to be Sdobyrev's, i.e. σ_red = σ₁ β + (1 − β)σ_i, where: σ₁-maximal principal stress, σ_i-stress intensity, β-material constant (at variable temperature β = β(T)). The methods of assessment of the material ageing grade are given in percentages of ageing of new material in the following mechanical properties: 1) creep strength in uniaxial stress state, 2) activation energy in uniaxial stress state, 3) criterion creep strength in complex stress states, 4) activation pseudoenergy in complex stress states. The methods 1) and 3) are the relatively simplest because they result from experimental investigations only at nominal temperature of the structure work, however, for methods 2) and 4) it is necessary to perform the experimental investigations at least at two temperatures.     

Production of hydrogen from sewage biosolids in a continuously fed bioreactor: Effect of hydraulic retention time and sparging

Hydrogen was produced from primary sewage biosolids via mesophilic anaerobic fermentation in a continuously fed bioreactor. Prior to fermentation the sewage biosolids were heated to 70 °C for 1 h to inactivate methanogens and during fermentation a cellulose degrading enzyme was added to improve substrate availability. Hydraulic retention times (HRT) of 18, 24, 36 and 48 h were evaluated for the duration of hydrogen production. Without sparging a hydraulic retention time of 24 h resulted in the longest period of hydrogen production (3 days), during which a hydrogen yield of 21.9 L H₂ kg⁻¹ VS added to the bioreactor was achieved. Methods of preventing the decline of hydrogen production during continuous fermentation were evaluated. Of the techniques evaluated using nitrogen gas to sparge the bioreactor contents proved to be more effective than flushing just the headspace of the bioreactor. Sparging at 0.06 L L min⁻¹ successfully prevented a decline in hydrogen production and resulted in a yield of 27.0  L H₂ kg⁻¹ VS added, over a period of greater than 12 days or 12 HRT. The use of sparging also delayed the build up of acetic acid in the bioreactor, suggesting that it serves to inhibit homoacetogenesis and thus maintain hydrogen production.