Polypyrrole Based Microwave Absorbers

Reflection of microwave radiations from single layer and two-layer materials is calculated. Microwave absorbing materials are formulated by mixing a commercially available paint or rubber with the conducting polypyrrole (PPy) powder. The reflection loss strongly depends on thickness and complex permittivity of the material. For a single layer material, optimum values of the real part, , and imaginary part, , of the complex permittivity are found by calculations which lead to a minimum reflectivity at a given sample thickness. The ability to readily tailor the conductivity of the PPy powder enables the design of microwave absorbers according to theoretical desired values of and . A paint panel containing 2 wt% of PPy powder with a thickness of 2.5 mm exhibits a reflectivity < – 10 dB (i.e. at least 90% absorption of the incident radiation) over 12 to 18 GHz. Blending and milling during the manufacturing process can destroy the original fibrous shape of PPy aggregates leading to low radiation absorption. In an attempt to achieve a broadband absorber, a two-layer system consisting of a first layer containing PPy powder and a second layer containing carbonyl iron has been fabricated.     

(Pre)kernel catchers for cooperative games

The paper provides a new (pre)kernel catcher in that the relevant set always contains the (pre)kernel. This new (pre)kernel catcher gives rise to a better lower bound _*** such that the kernel is included in strong -cores for all real numbers not smaller than the relevant bound _***.The research for this paper was done under the sponsorship of both the Dutch Organization for the Advancement of Scientific Research (NWO) and the National Science Council (NSC) of Taiwan during a stay of Dr. Chih Chang at the University of Twente, Enschede, The Netherlands.     

High-frequency dielectric behaviour of polycrystalline zinc substituted cobalt ferrites

The dielectric constant () and complex dielectric constant () of zinc substituted cobalt ferrites have been measured at room temperature in the high frequency range 100 kHz to 1 MHz. The values of dielectric loss tangent (tan ) have been computed from and . Plots of dielectric constant () versus frequency show a normal dielectric behaviour of the spinel ferrites. The frequency dependence of dielectric loss tangent (tan ) is found to be abnormal, giving a peak at certain frequency for all the ferrites under investigation. A qualitative explanation is given for the composition and frequency dependence of the dielectric constant and dielectric loss tangent. The dielectric constant for these mixed ferrites is approximately inversely proportional to the square root of the resistivity. A plot of dielectric constant versus temperature shows a transition near the Curie temperature. An attempt is made to explain the possible mechanism for this observation.     

Effective permittivity of layered dielectric sphere composites

A straightforward model is presented for analysing the effective permittivities of layered dielectric sphere composites. Using the present model, the effective permittivity, _eff, of layered dielectric sphere composites can be deduced using classical two-phase dielectric mixture formulae in two steps: first, the effective permittivity, _incl, of the inclusions is calculated by taking the layered dielectric sphere inclusions as sub-composites; and second, the effective permittivity, eff, of the composites is found by substituting the layered dielectric sphere inclusions with homogeneous spheres whose permittivity is equal to _incl. The present model is applicable to multi-layer sphere composites. Experiments on resin-based hollow bead composites show that the present model accurately predicts the effective permittivity of layered dielectric sphere composites.     

Optical investigation of SnS2 single crystals

The optical properties of the layered compound SnS₂ have been studied. Reflectivity spectra were measured at room temperature, in the energy region 1.8–5.6 eV. Optical transmission measurements were carried out in the temperature range 13–300 K, in order to evaluate the energy gaps and their temperature dependences. The spectra of the optical constantsn, , ₁ and ₂ versus photon energyh have also been presented.     

Investigation of microstructure of molybdenum—copper black electrodeposited coatings with reference to solar selectivity

Optical and microstructural properties of electrodeposited molybdenum-copper (Mo-Cu) black coatings have been studied with reference to their selectivity in absorption of solar radiation. Such coatings were found to have a solar absorptance, , about 0.87 and low thermal emittance, , such that the selectivity, /, was 3.6. Electrodeposited molybdenum-black coatings generally have selectivity /3. The oxidation state of molybdenum in (Mo-Cu) black coatings as determined by X-ray photoelectron spectroscopy is about + 5 (which is fairly close to that of Mo₄O₁₁). Large numbers of irregular particles were found on the surface of molybdenum-copper black coatings. There is evidence that the particles contain copper oxide.     

Study of dielectric and electrical properties of mortar in the early hydration period at microwave frequencies

The dielectric constant, , and electrical conductivity, , of mortars with various sand-cement ratios,s/c, were measured for the first 30 h hydration using microwave techniques in the frequency range 8.2–12.4 GHz. The and of the mortars were found to increase linearly with increasing water-solid ratiow/(s + c), but decrease with increasings/c. It was found that as long as thes/c values were the same, the rate of changes in and of the mortars were the same. It appears that thes/c is the key factor controlling the rates of changes in dielectric and electrical parameters of cement hydration in mortar. The relationship between compressive strength and dielectric and electrical properties of mortars was also discussed.     

Causes of the occurrence of an “effective” porosity in granular media

The cause of the difference between the total (geometric) and effective _ef (hydrodynamic) porosity of granular media is established.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 21, No. 6, pp. 1017–1024, December, 1971.     

Viscoelastic-plastic behaviour with mean strain changes in polypropylene

The stress-strain curves and stress-relaxation curves of polypropylene are obtained by using a closed-loop, electrohydraulic, servo-controlled testing machine. Effects of mean strain changes on deformation behaviour are examined in a tension-compression mode under strain control at room temperature (18–23 °C). The hysteresis loops of three mean strains show a steady-state response from the stress-strain curves at a strain rate of 1 × 10^–3 s^–1 at a strain width of 5%, at a number of cycles of N=50 and at three mean strains (_m=0, + 1.0 and + 2.0%). The drop of stress at the mean strain of _m= -1.0% is larger in magnitude than that at _m=+1.0%; this is caused by the higher stress level at _m=- 1.0% as compared with the stress level at _m=+1.0%. From the results of stress amplitude and the stress drop behaviour, the magnitude of stress drop is hardly affected by the mean strain.     

Low endurance fatigue in metals and polymers

The fatigue behaviour of commercially pure aluminium and of nylon under sequentially varying strain amplitudes is compared with a damage law of the type suggested by Miner. Aluminium obeys such a law for both cyclic and uniaxial prestrains but the behaviour of nylon is significantly affected by microcracking, which produces a marked effect of loading sequence.Appendix N Number of strain cycles at a given time - N _f Value of N at failure - True tensile stress - True stress range for a strain cycled specimen - _h Value of at half the life of the specimen - True tensile strain - Total true strain range - _p True plastic strain range (= the breadth of the hysteresis loop at = 0) - _d True diametral strain range - E Young's modulus - Linear strain hardening rate when tested at a particular value of _p - D Damage due to cycling - D _p Damage due to prestrain - _p Prestrain. C, K, K₁, , are constants     

A mathematical programming approach to a problem in variance penalised Markov decision processes

In this paper we present three algorithms for solving a problem in which it is required to get an optimal compromise between the average expected reward per unit time and the variance of the reward per unit time. The algorithms lead to an-optimal solution, where>0 is arbitrary.     

Dielectric constant,molar volume,and phase diagram of saturated liquid3He-4He mixtures

The dielectric constant of seven ³ He- ⁴ He mixtures has been measured in the saturated liquid phase at temperatures between 0.55 and 1.86 K. The Clausius-Mosotti function (–1)/(+2) is found to be nearly linear in concentration, especially at low temperatures. A method is described for determining the concentration from a measured dielectric constant. Measurements in the two-phase region are used to calculate the phase-separation curve. Molar volumes are calculated using polarizabilities consistent with those reported by Kerr and Sherman for the pure components.Work performed under the auspices of the U.S. Energy Research and Development Administration.     

Dynamic scaling and ultrasonic attenuation in 4He near the superfluid transition point

Attenuation of first sound has been measured in ⁴He under saturated vapor pressure near the lambda temperature T at frequencies /2 ranging from 10.2 to 271 MHz. The frequency dependence of the critical part of the attenuation is determined and the dynamic scaling hypothesis is examined. Above the lambda point, it is found that the critical attenuation is described by a scaling function (, ) = ^1+y F(), where = ₀^–x and = T/T – 1, with the results x = 1.02±0.05 and y = 0.33±0.03. The characteristic frequency of the order-parameter fluctuation with the wave number k equal to the inverse correlation length is then proportional to ^x , which is in an excellent agreement with the prediction of dynamic scaling. Below the lambda point, a characteristic relaxation time or times shorter than previously expected at lower frequencies appears to exist in the present frequency range.Based on a Ph.D dissertation submitted by K. Tozaki to the University of Tokyo (1977).     

Longitudinal dielectric function and collective surface oscillations in superconductors

The electrodynamic approach to the problem of collective oscillations in superconductors is considered. The kinetic equation for quasiparticles is used to find the longitudinal dielectric function ₁ (, k) of a pure superconductor at ( is the collision frequency). With the help of the evaluated ₁ (, k) the existence of collective oscillations localized near the boundary of the superconductor is investigated.     

The effect of ionizing radiation on dielectric properties of bovine achilles tendon collagen in the temperature range of thermal denaturation

The effect of -irradiation, with doses from 10²–2×10³ kGy, on the dielectric properties of solid-state collagen was studied. The temperature dependence of the constants and ' revealed a decrease in the denaturation temperature with increasing dose of irradiation. Dielectric dispersion observed in the frequency range 10 Hz to 10 kHz was suggested to be due to Maxwell-Wagner-Sillars polarization. In addition, an increase in the irradiation dose resulted in increasing activation energy of bovine achilles tendon collagen.     

Dielectric properties of polyarylate blends

Dielectric properties and molecular motion were studied by use ofdielectric spectroscopy and differential scanning calorimetry for twoblends, fully transesterificated polyarylate of bisphenol A withterephthalate/isophthalate (50/50) (PA)/polycarbonate of bisphenol A(PC) blends and PA/poly(ethylene terephthalate) (PET) blends. All thequenched PA/PC and PA/PET blends were amorphous and the glasstransition temperature (Tg) was varied with the blends ratioaccording to Gordon-Taylor equation. The PA/PET blends with more than60% of PET crystallized above the crystallization temperature. ThePA/PC and PA/PET blends showed two dielectric relaxations, above Tg and below Tg, which are related to a glasstransition and a local motion of short segment, respectively. The relaxation moved to lower temperatures as PC or PET contentincreases, reflecting the lowering Tg faithfully. In the PA/PETblends, the static (₀) and the limiting dielectricconstant (), and the increment () for the relaxation decreases with increasingtemperature and the decrease falled on one curve, independent of theblend ratio. Any ferro- and piezoelectricity were not observed fortwo blends.     

Application of the monte carlo method in the processing of experimental data on dynamic deformation of materials

The article presents a method of processing the recorded diagram of deformations vs time t for the purpose of determining the time-dependent change of strain rate and acceleration. The method is based on the utilization of data of statistical tests (the Monte Carlo method) and the least squares method applied to the deviations of the functions (t) from the experimental curve at the specified number of points.Translated from Problemy Prochnosti, No. 8, pp. 20–22, August, 1992.     

Anomalous normal state and high temperature superconductivity in the cuprates

It is generally believed that a high electronic density-of-states n(E_F), and therefore a low Fermi velocity v_F, are required to obtain a high transition temperature, since T_{c ph} exp(–1/) and = n(E_F)V. However, V = < I² >/M _ph ² , and Bardeen showed that I E_Fk_F = (1/2)k _F ² v_F. Thus one may expect that should increase with v_F. While it may not be feasable to increase the one-electron velocity v_F signifcantly, the velocity may increase greatly as a result of renormalization by electron-electron interactions. Such a renormalization exists in Hartree-Fock theory for an unscreened electron-gas. We found that for a medium-density electron-gas (r_s 10–20) imbedded in a background with a dielectric constant () such that / > 10, there is a significant increase of v_F by renormalization, even when screening is taken into consideration. The peak of v(k) at k = k_F is very narrow, the half width being somewhat less than the frequency ₀ at which () falls by a factor of 2. When () is due to ionic polarization, _o is a typical phonon frequency. The height of the peak v_F/v _F ⁰ is of order E_F/₀, and the width in units of momentum is: k/k_F (₀/E_F)². This velocity peak is associated with a minimum in the screening constant at E_p. Its sharpness causes the normal state properties to be highly anomalous; namely the conductivity is exceptionally high, with an anomalous temperature dependence; the conductivity anisotropy, thermoelectric power, and Hall constant are anomalous. Direct determination of v(k) in YBCO by several methods indeed suggests a large, sharp peak, the width being of order 10 me V. This peak manifests itself in the tunneling and point-contact spectroscopy I–V curves. We suggest that the reduced screening at the Fermi level, associated with this velocity peak, is responsible for the high T_c of the cuprates and several other exotic superconductors. Thus, the high T_c is a reflection of the anomalous normal-state properties.     

Measurement of temperature in a non-steady-state gas flow

A method is described for measuring the temperature of a non-steady-state gas flow with a thermocouple which is an inertial component of the first order.Notation T*_f non-steady-state gas flow temperature - T_t thermosensor temperature - thermal inertia factor of thermosensor - time - C total heat capacity of thermosensor sensitive element - S total heat-exchange surface between sensitive element and flow - heat-liberation coefficient - temperature distribution nonuniformity coefficient in sensitive element - Re, Nu, Pr, Bi, Pd hydromechanical and thermophysical similarity numbers - P^* total flow pressure - P static flow pressure - T^* total flow temperature - d_t sensitive element diameter - w gas flow velocity - flow density - flow viscosity - _f flow thermal conductivity - k gas adiabatic constant - R universal gas constant - M Mach number - T thermodynamic flow temperature - _o, _o and values at T=288°K - A, m, n, p, r coefficients - _c heat-liberation coefficient due to colvection - _r heat-liberation coefficient due to radiation - _b emissivity of sensitive element material - Stefan-Boltzmann constant - T_e temperature of walls of environment - _c, _r, _tc thermosensor thermal inertia factors due to convective, radiant, and conductive heat exchange - L length of sensitive element within flow - a thermal diffusivity of sensitive element material - _t thermal conductivity of sensitive element material Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 47, No. 1, pp. 59–64, July, 1984.     

Coefficients of mass transfer between a fluidized bed and the surface of a capillary-porous body

Results are presented from a theoretical determination of coefficients of mass transfer between a fluidized bed of porous particles and a capillary-porous body.Notation a particle radius - F area of contact of particles with the surface of the body - f percentage of area of surface of product in contact with the bubble phase - g acceleration due to gravity - i flow of liquid mass from a unit area of the surface - N number of fluidizations - n number of particles coming into contact with a surface of unit area per unit of time - p_p, p_b capillary potentials of particles and product - R₂, R₁ radii of narrow and broad pores inside the product - r radius of capillaries in the particles - S area of the surface being treated - T temperature of the bed - t time of treatment - u percentage content of liquid in the specimen - V volume of the product being treated - v mean square component of the fluctuation velocity of the particles in the direction normal to the surface - , * standard and corrected mass-transfer coefficients determined from (5) and (9) - _b, _b, _p porosities of product determined for all and for only the small pores and the porosity of the material of the particles - _d, _m porosity of the dense phase and the porosity of the bed in the state of minimum fluidization - _b, _p angles of wetting of the materials of the product and particles, respectively, by the liquid binder - , viscosity and density of the liquid - ₀ density of the dry product - surface tension coefficient of the liquid - characteristic time of contact of particles with the surface - Re_m Reynolds number corresponding to particle radius and minimum-bed-fluidization velocity [6] Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 40, No. 3, pp. 460–465, March, 1981.