Further Suppression of Surface-Recombination of an InGaP/GaAs HBT by Conformal Passivation

Conformal passivation on an InGaP/GaAs HBT with significant reduction in the base surface-recombination effect is demonstrated. Not only dc behaviors but also RF performances are remarkably improved compared with the conventional emitter-ledge structure. Based on the conformal passivation, i.e., the base surface is covered by the depleted InGaP ledge structure and sulfur ((NH₄)₂S_x ) treatment, lower base surface-recombination current density, lower specific contact resistance, lower sheet resistance, higher current gain, higher collector current, and higher maximum oscillation frequency are obtained     

Effects of InGaP heteropassivation on reliability of GaAs HBTs

For the self-aligned AlGaAs/GaAs HBTs with the mesa-etched emitter, the instability of the surface states on the extrinsic base passivated by nitride is a major cause of the severe degradation of current gain. In this paper GaAs HBTs employing InGaP ledge emitter in order to passivate the surface of the extrinsic base and to reduce the surface states exhibited the considerable improvement of the current gain reliability with the activation energy of 1.97 eV and MTTF of 4.8×10⁸ h at 140°C. However, under the strong stress conditions InGaP/GaAs HBTs also produced the considerable degradation. The possible origins were investigated.     

钝化边的制作及其对不同尺寸自对准InGaP/GaAs HBT性能的影响

采用全耗尽的In Ga P材料在基区Ga As表面形成钝化边(passivation ledge)的方法,研制出了带钝化边的自对准In Ga P/Ga As异质结双极晶体管(HBT) .通过对不同尺寸、有无钝化边器件性能的比较得出:钝化边对提高小尺寸器件的直流增益有明显效果,对器件的高频特性无明显影响.此外,钝化边的形成改善了所有实验器件的长期可靠性.     

新结构InGaP/GaAs/InGaP DHBT生长及特性研究

设计并生长了一种新的InGaP/GaAs/InGaP DHBT结构材料,采用在基区和集电区之间插入n+-InGaP插入层结构,以解决InGaP/GaAs/InGaP DHBT集电结导带尖峰的电子阻挡效应问题。采用气态源分子束外延(GSMBE)技术,通过优化生长条件,获得了高质量外延材料,成功地生长出带有n+-InGaP插入层结构的GaAs基InGaP/GaAs/InGaP DHBT结构材料。采用常规的湿法腐蚀工艺,研制出发射极面积为100μm×100μm的新型结构InGaP/GaAs/InGaP DHBT器件。直流特性测试的结果表明,所设计的集电结带有n+-InGaP插入层的InGaP/GaAs/InGaP DHBT器件开启电压约为0.15V,反向击穿电压达到16V,与传统的单异质结InGaP/GaAs HBT相比,反向击穿电压提高了一倍,能够满足低损耗、较高功率器件与电路制作的要求。     

Selective self-aligned emitter ledge formation for heterojunctionbipolar transistors

We have demonstrated a heterojunction bipolar transistor (HBT) structure and fabrication process which produces a self-aligned emitter passivation ledge without the use of a realigned photoresist mask or additional dielectric etch masks. The novel HBT structure utilizes dual etch-stop layers in the emitter to allow the fabrication of a ledge using a simple, selective, wet-chemical etch process. This ledge technology has been successfully demonstrated in the InGaP/GaAs HBT material system     

High-current-gain small-offset-voltage In0.49Ga0.51P/GaAs tunneling emitter bipolar transistors grown by gas sourcemolecular beam epitaxy

Different emitter size, self-aligned In_0.49Ga_0.51 P/GaAs tunneling emitter bipolar transistors (TEBTs) grown by gas source molecular beam epitaxy (GSMBE) with 100-Å barrier thickness and 1000-Å p⁺(1×10¹⁹ cm^-3) base have been fabricated and measured at room temperature. A small-signal current gain of 236 and a small common-emitter offset voltage of 40 mV were achieved without any grading. It is found that the emitter size effect on current gain was reduced by the use of a tunnel barrier. The current gain and the offset voltage obtained were the highest and lowest reported values to date, respectively, in InGaP/GaAs system heterojunction bipolar transistors (HBTs) or TEBTs with similar base dopings and thicknesses     

A reliability comparison of InGaP/GaAs HBTs with and without passivation ledge

InGaP/GaAs heterojunction bipolar transistors (HBTs) with and without passivation ledge in the extrinsic base region were investigated. Gummel plot changes before and after reliability testing were compared. The experimental results demonstrated that the devices featuring the lower quality of the extrinsic base surface are more sensitive to a temperature–current stress. The HBTs with a passivation ledge have an activation energy of 1.41 eV and a mean time to failure (MTTF) of 10⁶ h whereas the HBTs without passivation ledge have an activation energy of 1.24 eV and a MTTF of 10⁵ h.     

Implementation of reduced turn-on voltage InGaP HBTs using graded GaInAsN base regions

InGaP/GaInAsN double heterojunction bipolar transistors (HBTs) with compositionally graded bases are presented which exhibit superior dc and radio frequency performance. Reducing the average base layer energy gap and optimizing the emitter-base (e-b) and base-collector (b-c) heterojunctions leads to a 100-mV reduction in the turn-on voltage compared to a baseline InGaP/GaAs process. Simultaneously grading the base layer energy band-gap results in over a 66% improvement in the dc current gain and up to a 35% increase in the unity gain cutoff frequency. DC current gains as high as 250 and cutoff frequencies of 70 GHz are demonstrated. In addition, the InGaP/GaInAsN DHBT structure significantly reduces the common emitter offset and knee voltages, as well as improves the dc current gain temperature stability relative to standard InGaP/GaAs HBTs.     

InGaP/GaAs0.94Sb0.06/GaAs doubleheterojunction bipolar transistor

A novel InGaP/GaAs_0.94Sb_0.06/GaAs double heterojunction bipolar transistor is presented. It features the use of fully strained pseudomorphic GaAs_0.94Sb_0.06 as the base layer and an InGaP layer as the emitter, which both eliminate misfit dislocations and current blocking, and increase the valence band discontinuity at the InGaP/GaAsSb interface. The device demonstrates a high current gain and a low turn-on voltage     

High-performance InGaP/GaAs HBTs with compositionally graded bases grown by solid-source MBE

N-p-n InGaP/GaAs heterojunction bipolar transistors (HBTs) with compositionally graded In/sub x/Ga/sub 1-x/As (Be doped) bases have been successfully grown by solid-source molecular beam Epitaxy (SSMBE) using a gallium phosphide (GaP) decomposition source. In this paper, the dc and RF characteristics of HBTs with different indium mole fractions in the graded In/sub x/Ga/sub 1-x/As base (x:0 /spl rarr/ ;0.1 and x:0 /spl rarr/ 0.05) are measured to investigate optimum-grading profiles. The measured average current gains, /spl beta/s of a control sample, a 10% graded-base sample and a 5% graded-base sample, are 162, 397 and 362, respectively. To our knowledge, these current gains are the highest values ever reported in compositionally graded-base InGaP/GaAs HBTs with a base sheet resistance R/sub sh/ of /spl sim/200 /spl Omega//sq establishing a new benchmark for InGaP/GaAs HBTs. Furthermore, these compositionally graded-base HBTs show higher unity current/gain cutoff frequency, f/sub T/ and maximum oscillation frequency, f/sub max/. Compared to the control sample with the same base thickness, the base transit time /spl tau//sub B/ of the graded sample is reduced by /spl sim/15% to /spl sim/20% by the induced built-in potential, resulting in an increase of f/sub max/ from 16 to 18.5 GHz in a device with an emitter size of 10/spl times/10 /spl mu/m/sup 2/. Additionally, for the 5% graded-base sample, with a 5/spl times/5 /spl mu/m/sup 2/ emitter region, f/sub T/ and f/sub max/ are 16.3 and 33.8 GHz, respectively, under low-level collector current. These results demonstrate that InGaP/GaAs HBTs with In/sub x/Ga/sub 1-x/As graded-base layers (x:0 /spl rarr/ 0.05) have the potential for high-speed analogue to digital converters.     

Comparison of heterostructure-emitter bipolar transistors (HEBTs) with InGaAs/GaAs superlattice and quantum-well base structures

The characteristics of InGaP/GaAs heterostructure-emitter bipolar transistors (HEBTs) including conventional GaAs bulk base, InGaAs/GaAs superlattice-base, and InGaAs quantum-well base structures are presented and compared by two-dimensional simulation analysis. Among of the devices, the superlattice-base device exhibits a highest collector current, a highest current gain and a lowest base–emitter turn-on voltage attributed to the increased charge storage of minority carriers in the InGaAs/GaAs superlattice-base region by tunneling behavior. The relatively low turn-on voltage can reduce the operating voltage and collector–emitter offset voltage for low power consumption in circuit applications. However, as to the quantum-well base device, the electrons injecting into the InGaAs well are blocked by the p⁺-GaAs bulk base and it causes a great quantity of electron storage within the small energy-gap n-type GaAs emitter layer, which significantly increases the base recombination current as well as degrades the collector current and current gain.     

A novel InGaP/Al/sub x/Ga/sub 1-x/As/GaAs CEHBT

A new and interesting InGaP/Al/sub x/Ga/sub 1-x/As/GaAs composite-emitter heterojunction bipolar transistor (CEHBT) is fabricated and studied. Based on the insertion of a compositionally linear graded Al/sub x/Ga/sub 1-x/As layer, a near-continuous conduction band structure between the InGaP emitter and the GaAs base is developed. Simulation results reveal that a potential spike at the emitter/base heterointerface is completely eliminated. Experimental results show that the CEHBT exhibits good dc performances with dc current gain of 280 and greater than unity at collector current densities of J/sub C/=21kA/cm/sup 2/ and 2.70/spl times/10/sup -5/ A/cm/sup 2/, respectively. A small collector/emitter offset voltage /spl Delta/V/sub CE/ of 80 meV is also obtained. The studied CEHBT exhibits transistor action under an extremely low collector current density (2.7/spl times/10/sup -5/ A/cm/sup 2/) and useful current gains over nine decades of magnitude of collector current density. In microwave characteristics, the unity current gain cutoff frequency f/sub T/=43.2GHz and the maximum oscillation frequency f/sub max/=35.1GHz are achieved for a 3/spl times/20 /spl mu/m/sup 2/ device. Consequently, the studied device shows promise for low supply voltage and low-power circuit applications.     

High-speed InGaP/GaAs heterojunction bipolar transistors withburied SiO2 using WSi as the base electrode

High-speed InGaP/GaAs heterojunction bipolar transistors (HBT's) with a small emitter area are described. WSi is used as the base electrode to fabricate HBT's with a narrow base contact width and a buried SiO₂ structure. An HBT with an emitter area of 0.8×5 μm exhibited an f_T of 105 GHz and an f_max of 120 GHz. These high values are obtained due to the reduction of C_BC by using buried SiO₂ with a narrow base contact width, indicating the great potential of GaAs HBT's for high-speed and low-power circuit applications     

Determination of thermal resistance using Gummel measurement for InGaP/GaAs HBTs

In this paper, we propose a technique to determine thermal resistance of InGaP/GaAs heterojunction bipolar transistors (HBTs). The technique is based on Gummel measurement at only a few substrate temperatures. The major advantage of this technique is the simplicity in measurement, since the temperature-dependent parameter does not need to be determined for each device size. Therefore, when a number of devices need to be measured, this technique is less time-consuming. Another feature of this technique is the separation of the thermal resistance and emitter resistance, so that it is easier to optimize the emitter resistance. The result shown in this paper is measured from an InGaP/GaAs HBT, and is compared with another typical technique.     

高性能六边形发射极InGaP/GaAs异质结双极型晶体管

六边形发射极的自对准InGaP/GaAs异质结具有优异的直流和微波性能.采用发射极面积为2μm×10μm的异质结双极型晶体管,VCE偏移电压小于150mV,膝点电压为0.5V(IC=16mA),BVCEO大于9V,BVCBO大于14V,特征频率高达92GHz,最高振荡频率达到105GHz.这些优异的性能预示着InGaP/GaAs HBT在超高速数字电路和微波功率放大领域具有广阔的应用前景.     

Optimization of emitter cap growth conditions for InGaP/GaAs HBTs with high current gain by LP-MOCVD

The effect of emitter cap growth conditions on the common-emitter current gain of InGaP/GaAs HBTs, grown by LP-MOCVD, has been studied. This work shows that the material quality of a carbon-doped base is highly dependent on the emitter cap growth. The emitter cap growth effectively serves as a source of thermal stress. This stress on the base during the emitter and cap growth causes the formation of carbon-related defects in the base that increase the base recombination and reduces the current gain. Atomic force microscopy is used to identify these carbon-related defects. Gain improvements of about 40% have been achieved by optimizing the emitter cap growth conditions to reduce the thermal stress.     

基区设计对InGaP/GaAs HBT热稳定性的影响

研究了不同基区设计对多发射极指结构功率InGaP/GaAs异质结双极型晶体管热稳定性的影响。以发生电流增益崩塌的临界功率密度为热稳定性判定标准,推导了热电反馈系数Φ、集电极电流理想因子η和热阻Rth与基区掺杂浓度NB、基区厚度dB的理论公式。基于TCAD虚拟实验,观测了不同基区掺杂浓度和不同基区厚度分别对InGaP/GaAs HBT热稳定性的影响。结合理论公式,对仿真实验曲线进行了分析。结果表明,基区设计参数对热稳定性有明显的影响,其影响规律不是单调变化的。通过基区外延层参数的优化设计,可以改进多指HBT器件的热稳定性,从而为多指InGaP/GaAs HBT热稳定性设计提供了一个新的途径。     

Optimal quantum well width and the effect of quantum well position on the performance of transistor lasers

Transistor laser (TL) model based on InGaP/GaAs/InGaAs/GaAs is analyzed and presented. It is realized that quantum well (QW) with width of 10 nm may be formed for low base threshold current density J th . The emission wavelength is found to be 1.05 μm, and the indium (In) composition is 0.25 for optimal QW width. It is identified that J th decreases with the movement of QW towards the base-emitter (B-E) interface. Small signal optical response is calculated, and the effect of QW position is studied. The bandwidth is enhanced due to the movement of the QW towards the emitter base junction.     

High-speed, low-noise InGaP/GaAs heterojunction bipolar transistors

We have demonstrated self-aligned InGaP/GaAs heterojunction bipolar transistors (HBT's) with excellent dc, microwave, and noise performance. A 3×10 μm² emitter finger device achieved a cutoff frequency of f_T=66 GHz and a maximum frequency of oscillation of f_max=109 GHz. A minimum noise figure of 1.12 dB and an associated gain of 11 dB were measured at 4 GHz. These results are the highest combined f_T+f_max and the lowest noise figure reported for an InGaP/GaAs HBT and are attributed to material quality and the use of self-aligned base contacts. These data clearly demonstrate the viability of InGaP/GaAs HBT's for high-speed, low-noise circuit applications