Interface microstructure and mechanical properties of Ni–Co–P alloy coatings modified carbon fibres reinforced 7075Al matrix composites

To optimize interface microstructure between 7075Al matrix and CFs, Ni–Co–P multi-component alloy coatings coated carbon fibres were prepared by electroless plating firstly and then Ni–Co–P coated CFs reinforced 7075Al matrix composites (CF/Al(Ni–Co–P)) with high relative density were fabricated by hot pressing sintering process. After modification of Ni–Co–P coatings, Al–Co–Ni Intermetallic compounds were formed stably between matrix and reinforcement because of the smaller mixing enthalpy values of Al–Co, Al–Ni and Co–Ni, which not only restrained the generation of Al₄C₃ but also improved interfacial bonding strength. Yield strength and ultimate tensile strength of CF/Al(Ni–Co–P) composites with 30 vol% CFs had maximum improvement compared with CF/Al(U) composites than other composites reinforced by 10 vol%, 20 vol% and 30 vol%CFs, which is up to 305.8 MPa and 668.7 MPa respectively, and the fracture mode of composites from accumulation fracture to non-accumulation fracture as the existence of Ni–Co–P coatings.     

氮化硅陶瓷的无压烧结工艺优化及性能研究

以α-Si3 N4为原料,Y2 O3和MgO为复合烧结助剂,通过无压烧结制备出氮化硅陶瓷。为了优化实验配方和工艺参数,采用正交实验研究了成型压力、保压时间、保温时间、烧结温度、烧结助剂含量以及配比对氮化硅陶瓷气孔率和抗弯强度的影响规律。结果表明,影响氮化硅陶瓷气孔率的主要因素是烧结助剂含量和配比,而影响其抗弯强度的主要因素是烧结助剂配比和烧结温度。经分析得出,最佳工艺参数为成型压力16 MPa,保压时间120 s,保温时间2 h,烧结温度1750℃,烧结助剂含量12wt％,烧结助剂配比1∶1;经最佳工艺烧结后的氮化硅陶瓷,相对密度为94．53％,气孔率为1．09％,抗弯强度为410．73 MPa。     

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Zirconia ceramic is a significant structural material, but its use under some extreme circumstances is limited by its mechanical properties. In this work, SiC particles (SiCp) were added into alumina toughened zirconia ceramics to prepare ZrO₂–Al₂O₃-SiCp ceramics with high performance by using oscillatory pressure sintering (OPS). Results showed that the best OPS temperature of 1600 °C was obtained, and the optimal SiCp particle size and content were 200 nm and 10 vol% respectively. Under these conditions, the specimen exhibited higher mechanical properties including Vickers hardness of 15.43 GPa, bending strength of 1162 MPa and fracture toughness of 6.36 MPa m^1/2. Moreover, it was found that the atomic matching between ZrO₂/SiCp, Al₂O₃/SiCp, and ZrO₂/Al₂O₃ was much higher, showing the coherent interface relationship. Therefore, it was favorable for enhanced mechanical properties of as-prepared ZrO₂–Al₂O₃-SiCp ceramics.     

Preceramic paper-derived Ti3Al(Si)C2-based composites obtained by spark plasma sintering

The paper describes the structure and properties of preceramic paper-derived Ti₃Al(Si)C₂-based composites fabricated by spark plasma sintering. The effect of sintering temperature and pressure on microstructure and mechanical properties of the composites was studied. The microstructure and phase composition were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. It was found that at 1150 °C the sintering of materials with the MAX-phase content above 84 vol% leads to nearly dense composites. The partial decomposition of the Ti₃Al(Si)C₂ phase becomes stronger with the temperature increase from 1150 to 1350 °C. In this case, composite materials with more than 20 vol% of TiC were obtained. The paper-derived Ti₃Al(Si)C₂-based composites with the flexural strength > 900 MPa and fracture toughness of >5 MPa m^1/2 were sintered at 1150 °C. The high values of flexural strength were attributed to fine microstructure and strengthening effect by secondary TiC and Al₂O₃ phases. The flexural strength and fracture toughness decrease with increase of the sintering temperature that is caused by phase composition and porosity of the composites. The hardness of composites increases from ~9.7 GPa (at 1150 °C) to ~11.2 GPa (at 1350 °C) due to higher content of TiC and Al₂O₃ phases.     

Bioinspired nacre-like 2024Al/B4C composites with high damage tolerance

The bio-inspired 2024Al/B₄C composites with a laminate-reticular hierarchical architecture were constructed by squeeze casting of 2024Al into loose freeze-cast ceramic scaffolds. This pressurized infiltration process provided a clean and well-bonded interface without physical gaps. By regulating the initial suspension concentration (20, 25, 30 and 35 vol%), the effects of different ceramic content on the microstructure, damage-tolerance behavior and toughening mechanisms of the composites parallel and perpendicular to the ice-growth direction were investigated. The strength and toughness in the longitudinal direction were greater than that in the transverse direction. The 2024Al/20 vol% B₄C composite in the longitudinal direction yielded the highest flexural strength of 658 MPa, crack-initiation toughness (K_Ic) of 18.4 MPa m^1/2 and crack-growth toughness (K_Jc) of 27.5 MPa m^1/2. The unique damage-tolerant properties were attributed to multiple toughening mechanisms, including crack deflection, branching and blunting, ductile-ligament bridging and multiple-crack propagation, as evidenced by the stable crack growth and rising R-curve behavior during fracture. The significantly decreased damage tolerance in the transverse direction was mainly due to inadequate toughening tools. On the other hand, both the flexural strength and fracture toughness reduced remarkably as the ceramic content increased. The 2024Al/35 vol% B₄C composite fractured in a single-crack mode and the crack growth path was almost straight, showing a relatively low ?exural strength (502 MPa) and crack-initiation toughness (9.1 MPa m^1/2). The toughening mechanism was discussed in terms of the relationship between structural characteristics and cracking mode.     

Spark plasma sintering of TiC–SiCw ceramics

Silicon carbide whiskers (SiC_w) in TiC had impressive impacts on the properties and made it possible for special applications which generally would not be conceivable with TiC alone. In the present work, SiC_w reinforced TiC based composites were prepared by spark plasma sintering (SPS) technique, at the temperature of 1900 °C under the pressure of 40 MPa for sintering time of 7 min. To test out the effects of different amount of SiC whisker (0, 10, 20 and 30 vol%) on the characteristics of TiC, the sintered samples were investigated about sinterability and physical-mechanical properties. Microstructure observations and density measurements confirmed that the composites were dense with uniformly distributed reinforcement, and the specimen doped with higher than 10 vol% SiC_w could attain higher relative density (>100%) than pure TiC and TiC–10 vol% SiC_w. Also, the highest values for hardness (29.04 GPa) and thermal conductivity (39.2 W/mK) were achieved in specimen containing 30 vol% SiC_w, whereas the optimum bending strength (644 MPa) was recorded in material containing 20 vol% SiC_w. It seems that one of the reasons which contributes to this trend of properties variation is the generation of near-stoichiometric TiC_x phase and new Ti₃SiC₂ compound.     

真空热压烧结制备高性能B4C/Al复合材料

B4C/Al复合材料因其优异的性能,受到了人们广泛关注.以Al粉和B4C粉体为原料,采用真空热压烧结法,在高于Al熔点温度时,制备出了碳化硼含量10wt%的铝基复合材料.研究结果表明:烧结温度为700 ℃,烧结压力为30 MPa,保温时间为45 min时,获得的B4C/Al复合材料力学性能最佳,其相对密度为98.2%,硬度为2.53 GPa,抗弯强度为350 MPa.球磨混料使Al颗粒表面生成少量Al2O3,在烧结过程中,Al2O3与B2O3发生固-液反应形成共融物,改善了B4C/Al之间的界面结合强度,从而获得力学性能优异的B4C/Al复合材料.     

Development and evaluation of Al2O3–ZrO2 composite processed by digital light 3D printing

Digital Light Processing (DLP) is a promising approach to fabricate delicate ceramic components with high-fidelity structural features. In this work, the alumina and zirconia/alumina ceramic suspensions with low viscosity and high solid loading (40 vol%) were prepared specifically for DLP 3D printing. After debinding and sintering, the final parts were obtained without any defects. The surface morphologies and mechanical properties of alumina (Al₂O₃) and zirconia toughened alumina (ZTA) composites were investigated and the results showed that the final parts exhibited high relative densities and good interlayer combination at the sintering temperature of 1600 °C. Comparing with the Al₂O₃, the ZTA composites exhibited significantly enhanced density (99.4%), bending strength (516.7 MPa) and indentation fracture toughness (7.76 MPa m^1/2).     

Optimization of spark plasma sintering parameters of Si3N4-SiC composite using response surface methodology (RSM)

The Si₃N₄-SiC micro-nano composites were fabricated via the spark plasma sintering method using MgSiN₂ as an additive. Response surface methodology and central composite design were applied to optimize the spark plasma sintering process for the fabrication of Si₃N₄-SiC/MgSiN₂ with improved density. The relation between the three parameters of sintering including temperature, pressure, and holding time was modeled and the optimized parameters were obtained. The best sintering results obtained for the sintering temperature, holding time, and pressure are 1700 °C, 487 s, and 49 MPa, respectively. The addition of MgSiN₂ as an additive and SiC as a secondary phase were also investigated in the present work. The Si₃N₄−5 vol% SiC composite exhibited high hardness (19 GPa) and fracture toughness values (6.5 MPa m^1/2) at room temperature.     

Influence of SPS temperature on the properties of TiC–SiCw composites

Titanium carbide (TiC) composites containing 10 vol% silicon carbide whisker (SiC_w) were spark plasma sintered at different temperatures of 1800, 1900, and 2000 °C under a pressure of 40 MPa and a holding time of 7 min. At the sintering temperature of 1900 °C, the relative density, Vickers hardness, and flexural strength of the sintered samples hit their maximum values of 98.7%, 24.4 GPa, and 511 MPa, respectively. The microstructural characteristics of the sintered samples were assessed by optical and field emission scanning electron microscopy (FESEM) and XRD. The results revealed that at 1900 °C, the dispersion of SiC_w in the TiC matrix was homogenous, no chemical reaction took place between the reinforcement and the matrix, and produced a fine-grained microstructure. It was found that the thermal conductivity of SPSed samples did not have the same trend with relative density and mechanical properties. A maximum value of 32.3 W/mK was measured for the thermal conductivity of the composite sintered at 2000 °C.     

Performance of B4C/CeB6 composites fabricated via hot pressing under different processes

In this work, CeO₂ sintering additive reinforced B₄C ceramic composites were prepared by hot-pressing reaction sintering under different processes of low temperature–long holding time (1980°C, 30 MPa, 3 h, 4 wt% CeO₂) and high temperature–short holding time (2050°C, 30 MPa, .5 h, 4 wt% and 6 wt% CeO₂). The effect of sintering process and CeO₂ content on the microstructure and mechanical properties of B₄C-CeB₆ composites were investigated. The existed impurities in the obtained composites were also analyzed. Results show that CeO₂ is an active sintering additive. CeB₆ is formed by the reaction between CeO₂, B₄C and C in sintering process. The densification of B₄C ceramics is enhanced, and the grains can be refined by the formed CeB₆, which promotes the strength. The thermal expansion coefficient mismatch, crack deflection, and fracture mode change caused by the in situ formed CeB₆ improve the toughness. The process of low temperature–long holding time is more suitable for playing the role of CeO₂ additive in sintering of B₄C, under which condition the relative density, flexural strength, fracture toughness, and hardness reach 99%, 417 MPa, 5.32 MPa·m^1/2, and 30.66 GPa, respectively. The impurities in the composites are the kinds of Ti-contained, C-O-Mg-Ca-contained, C-O-Ca-S-contained, and Si-contained impurities.     

Mechanical Properties and Microstructure of Nano-SiC–Al2O3 Composites Densified by Spark Plasma Sintering

Heterogeneous precipitation method has been used to produce 5 vol% SiC–Al₂O₃ powder, from aqueous suspension of nano-SiC, aqueous solution of aluminium chloride and ammonia. The resulting gel was calcined at 700°C. Nano-SiC–Al₂O₃ composites were densified using spark plasma sintering (SPS) process by heating to a sintering temperature at 1350, 1400, 1450, 1500 and 1550°C, at a heating rate of 600 °/min, with no holding time, and then fast cooling to 600°C within 2–3 min. High density composites could be achieved at lower sintering temperatures by SPS, as compared with that by hot-press sintering process. Bending strength of 5 vol% SiC–Al₂O₃ densified by SPS at 1450°C reached as high as 1000 MPa. Microstructure studies found that the nano-SiC particles were mainly located within the Al₂O₃ grains and the fracture mode of the nanocomposites was mainly transgranular fracture.     

In-situ fabrication of TiC-Fe3Al cermet

Titanium carbide has high hardness, resistance to oxidation and abrasion while iron aluminide has proper ductility as well as good strength and excellent oxidation resistance up to high temperatures. Therefore, it can be expected TiC-iron aluminide cermet to have excellent mechanical properties as a cutting tool and a wear-resistance material. In this study, mechanical milling and hot press sintering processes were used to manufacture in-situ TiC-Fe₃Al cermet, whose microstructure and mechanical properties were examined according to the changes in volume fraction of TiC and milling time. After 48 h of milling each mechanically alloyed powder crystallized in a TiC and Fe₃Al biphasic material. The milled powder was hot-pressed at 1250 ℃ and 50 MPa for 30 min to obtain sintered bodies also consisting of only TiC and Fe₃Al phases. The hard phase, TiC, had a size of 100–300 nm with overall uniform distribution decreasing as the volume fraction of TiC increased. The hardness of each sintered body showed a linearly increasing tendency according to the increase in TiC content, the hardness for 90 vol% TiC cermet being as high as 1813Hv. On the other hand, the bending strength was 1800 MPa and 1780 MPa when TiC volume fraction was 50% and 70%, respectively, while it showed an abrupt decrease up to 580 MPa at 90% TiC volume fraction. Fe₃Al phase is effective to toughening of TiC-Fe₃Al cermet and the volume fraction of Fe₃Al phase significantly influences the bending strength of the cermet.     

Design and optimization of TiB2-based ceramic tool materials based on fuzzy theory

Based on the material properties and fuzzy theory, a new design method of TiB₂-based composite ceramic tool material was proposed, and the TiB₂-based composite ceramic tool material with excellent friction and wear resistance was designed. Initially, the fuzzy evaluation method was used to establish the matrix of the friction and wear resistance of the material, and the TiB₂-based material component with excellent friction and wear resistance was determined. Ultimately, based on the principle of fuzzy cognitive map, the correlation mapping of “sintering process–microstructure–mechanical properties” was established, and the composition ratio and sintering process were optimized. The results show that the TiB₂–TaC–TiC ceramic tool material had excellent friction and wear resistance. When the volume content of TaC was 8 vol.%, the volume content of TiC was 20 vol.%, the heating rate was 100°C/min, the holding time was 8 min, the sintering temperature was 1600°C, and the sintering pressure was 50 MPa, the mechanical properties were hardness 23.5 GPa, bending strength 438 MPa, and fracture toughness 10.26 MPa∙m^1/2.     

Effects of holding time on structure and the properties of spodumene/mullite composite ceramics

In this paper, spodumene/mullite ceramics with good thermal shock resistance were prepared from spodumene, quartz, talc, and clay when the sintering temperature was 1270℃. In the sintering process, the effect of holding time on densification, mechanical properties, phase transformation, microstructure, and thermal shock resistance of the composite ceramics were investigated. The phase transition and microstructures of the ceramics were identified via X-ray diffraction (XRD) and scanning electron microscopy (SEM). The interaction between holding time and bulk density was studied by response surface methodology. The result show that an appropriate holding time can improve the mechanical properties of spodumene/mullite ceramics. When the holding time was kept 90 min, the spodumene/mullite ceramics with the apparent porosity was .47%, the bulk density was 2.28 g/cm³, and bending strength was 63.46 MPa. Furthermore, since no cracks formed after 20 thermal shock cycles for the composite ceramics with a bending strength decreasing rate of 12.66%, it is revealed that spodumene/mullite ceramics exhibit good thermal shock resistance. Therefore, this study can provide beneficial guidance for both industrial production and energy conservation.     

Advantages and disadvantages of graphite addition on the characteristics of hot-pressed ZrB2–SiC composites

ZrB₂–SiC–graphite composites with 0–35 vol% graphite flakes were densified via hot-pressing route at the temperature of 1800 °C under the uniaxial pressure of 40 MPa for 1 h. Consolidation, mechanical properties, and microstructure of hot-pressed composites were investigated by variation of graphite content. By the addition of graphite, the relative density of composites increased, and at this hot pressing condition, fully densified composites were fabricated. The highest flexural strength of 366 MPa was measured for composite containing 7.5 vol% graphite, while the maximum Vickers hardness resulted in 2.5 vol% graphite doped one, and its value was equal to 20.8 GPa. Phase analysis of hot-pressed samples revealed the formation of the Zr₃C₂ and B₄C phases besides the main existing ZrB₂, SiC, and graphite phases. The newly carbide phases formed at the surface of ZrB₂ grains. The addition of graphite into the ZrB₂–SiC composites improved the sintering process and caused a fine-grained microstructure.     

Effect of Cu and Zn elements on morphology of ceramic particles and interfacial bonding in TiB2/Al composites

The 50 vol% TiB₂/Al composites with different alloying elements (Cu and Zn) were prepared by hot pressing sintering. The effects of Zn and Cu on the micromorphology of TiB₂ ceramic particles and interfacial behavior between TiB₂ ceramic and Al matrix as well as the mechanical properties of composites were investigated. Results indicated that the addition of Zn and Cu not only significantly enhanced the interfacial bonding strength between TiB₂ ceramic particles and Al matrix but also facilitated the reaction by reducing the reaction temperature in the Al–Ti–B system. Furthermore, the yield strength (719 MPa) and ultimate compressive strength (1130 MPa) of TiB₂/Al-6wt.%Cu composite increased by 48.8% and 26.4%, respectively, compared with that of the composite without alloy element. For the TiB₂/Al-6wt.%Zn composite, the yield strength and ultimate compressive strength increased by 15.3% and 7.8%, respectively. The improvement on the mechanical properties can be attributed to solid solution strengthening and second phase strengthening.     

二硼化锆基超高温陶瓷的制备及性能

用碳化硅(SiC)颗粒增韧二硼化锆(ZrB2)陶瓷,在氩气流中热压烧结温度为1 950℃、保温1 h,20 MPa压力下成功制备出了致密的ZrB2/SiCp复合材料.ZrB2/SiCp复合材料的致密度随着SiC颗粒添加量的增加而增加.当SiC颗粒的体积分数(下同)为15%时,相对致密度达到100%.ZrB2/SiCp复合材料的抗弯强度和断裂韧性都随着SiC添加量的增加成上升趋势,当SiC颗粒的添加量在15%时同时达得最大值,分别为646 MPa和8.52 MPam·m1/2.SiCp的添加还提高了ZrB2/SiCp复合材料的耐氧化烧蚀性能.     

Low-temperature sintering and microstructure control of mullite–Mo composites

Dense mullite–Mo (45 vol%) composites with homogeneous microstructure have been obtained by plasma activated sintering of a mixture of Mo and mullite precursors at a relatively low temperature (1350 °C) and a pressure of 30 MPa. The mullite precursor was synthesized by a sol–gel process followed by a heat-treatment at 1000 °C. The influence of different mullite precursors on the densification behavior and the microstructure of mullite–Mo composites has been studied. The precursor powder heat-treated at 1000 °C with only Si–Al spinel but no mullite phase shows an excellent sintering activity. Following the sintering shrinkage curves, a two-stage sintering process is designed to enhance the composite densification for further reducing the sintering temperature. The study reveals that viscous flow sintering of amorphous SiO₂ at low temperatures effectively enhances the densification. Moreover, microstructure of these composites can be controlled by selecting different precursors and sintering temperatures.     

Effect of short carbon fiber content on the mechanical properties of TiB2-based composites prepared by spark plasma sintering

In this study, TiB₂-30 vol% SiC composites containing 0, 5, 10, and 15 vol% short carbon fibers (C_f) were produced by spark plasma sintering (SPS). The effect of carbon fiber content on microstructure, density, and mechanical properties (micro-hardness and flexural strength) of the fabricated composites was studied. Scanning electron microscopy (SEM) results indicated that the fibers were uniformly dispersed in the TiB₂–SiC matrix using wet ball milling before SPS process. Fully dense TiB₂–SiC–C_f composites were achieved by SPS process at 1900°C for 10 min under 30 MPa. With the addition of fibers, the relative density of the composites did not change considerably. Mechanical tests revealed that microhardness was reduced about 19% by the incorporation of carbon fibers, whereas the flexural strength improved significantly. However, the flexural strength diminished by adding carbon fibers above to critical value (5 vol%) due to residual thermal stresses, nonhomogeneous structure and graphitization of carbon fibers. It was found that the composite with 5 vol% C_f had the highest flexural strength (482 MPa), which was enhanced by 20% compared with the TiB₂–SiC composite.