Evaluation of mechanical properties of acrylated guar gum – unsaturated polyester composites

Guar gum (GG) and its derivatives are commonly used in aqueous solutions as rheology modifiers. The use of polysaccharides as fillers in thermoset polymer composites has as yet not received that attention attributed to other materials. In the present study GG and the effect of acrylation on its filler properties were evaluated. Unsaturated polyester composites were evaluated for their mechanical properties as well as solvent resistance and water absorption. It was observed that the acrylate derivatives with the highest degree of substitution resulted in composites with the best mechanical properties as well as increased toluene and water resistance. Thus, polysaccharides could be used as reinforcing fillers in thermoset composites.     

Sintering and mechanical properties of tricalcium phosphate–fluorapatite composites

Tricalcium phosphate and synthesized fluorapatite powder were mixed in order to elaborate biphasic ceramics composites. The effect of fluorapatite addition on the densification and the mechanical properties of tricalcium phosphate were measured with the change in composition and microstructure of the bioceramic. The Brazilian test was used to measure the mechanical resistance of the tricalcium phosphate–26.52 wt% fluorapatite composites. The densification and rupture strength increase versus sintering temperature. The composites have a good sinterability and rupture strength in temperature ranging between 1300 and 1400 °C. Thus, the densification ultimate was obtained at 1350 °C and the mechanical resistance optimum reached 9.6 MPa at 1400 °C. Above 1400 °C, the densification and the mechanical properties were hindered by the allotropic transformation of tricalcium phosphate, grain growth and the formation of both intragranular porosity and many cracks. The ³¹P magic angle spinning nuclear magnetic resonance analysis of composites reveals the presence of tetrahedral P sites.     

Processing and mechanical properties of hydroxyapatite–polysulfone laminated composites

Designing biocomposites that mimic bone with specific mechanical properties of toughness and elastic modulus is a long-standing challenge in the biomaterials field. Traditional biocomposites comprise polymer matrices reinforced with ceramic particles. Laminated composites are structures also found in nature that can offer improved mechanical properties such as strength, elastic modulus and toughness. Hydroxyapatite/polysulfone laminated composites were fabricated to develop biologically compatible, toughened composites that would match the elastic modulus of bone. Multilayered composites were successfully designed with improved toughness measured by the work of fracture. Toughness measurements were more than an order of magnitude greater than monolithic hydroxyapatite. The toughness and modulus values of hydroxyapatite/polysulfone were within the range of cortical bone.     

Preparation，properties and applications of hydroxyapatite/synthetic polymer composites

随着生物医用材料的需求量日趋增大,磷灰石与人工合成高分子的复合材料成为组织修复和替代材料的研究热点。以不同单体分类,综述了磷灰石与合成的非降解高分子、可降解高分子复合材料的研究进展;对羟基磷灰石/合成高分子复合材料的制备方法、性能及其应用等方面进行研究,并对此复合材料存在的问题和发展前景进行讨论。说明从分子水平设计出具有良好力学性能、生物活性和生物相容性的医学材料,具有十分重要的意义。     

Improvement in mechanical properties in AlN–h-BN composites with high thermal conductivity

It is possible to improve the machinability of aluminum nitride–hexagonal boron nitride (AlN–h-BN) ceramics while maintaining high strength and high thermal con...     

Effects of vinyltrimethoxy silane on thermal properties and dynamic mechanical properties of polypropylene–wood flour composites

The viability of vinyltrimethoxy silane was investigated as a coupling agent for the manufacture of wood–plastic composites (WPC). The effect of silane pretreatment of the wood flour on the thermal and the dynamic mechanical properties and thermal degradation properties of the composites were studied. Moreover, the effect of organosilane on the properties of composites was compared with the effect of maleated polypropylene (MAPP). DSC studies indicated that the wood flour acts as a PP-nucleating agent, increasing the PP crystallization rate. In general, pretreatment with small amounts of silane improved this behavior in all the WPCs studied. Thermal degradation studies of the WPCs indicated that the presence of wood flour delayed degradation of the PP. Silane pretreatment of the wood flour augmented this effect, though without significantly affecting cellulose degradation. Studies of dynamic mechanical properties revealed that the wood flour (at up to 30 wt %) increased storage modulus values with respect to those of pure PP; in WPCs with a higher wood flour amount, there was no additional increase in storage modulus. Pretreatment of the wood flour with silane basically had no effect on the dynamic mechanical properties of the WPC. These results show that with small amounts of vinyltrimethoxy silane similar properties to the MAPP are reached. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis,microstructure and mechanical properties of lamellar YB2C2 – based ultra-high temperature ceramic composites

A significant improvement of the mechanical performance was observed following the introduction of rare earth oxides in ZrB₂-based ultra-high temperature ceramic matrix composites (UHTCMCs), resulting in the formation of ternary boro-carbides of general formula REB₂C₂, belonging to a new class of layered compounds akin to MAX phases. These layered phases possess high melting points and could be responsible for the toughening of UHTCMCs, but their formation, properties and role were never fully investigated. In this study we focused on the potential routes for the synthesis of YB₂C₂ phases at temperatures typical of UHTC sintering, starting from Y₂O₃, carbon and four different boron sources (B, B₂O₃, BN, B₄C) and their microstructure was analysed by SEM, XRD and TEM. The mixture with B₄C led to the highest selectivity towards the formation of YB₂C₂ and was selected to fabricate a long carbon fibre reinforced YB₂C₂ ceramic composite, which was mechanically tested displaying a flexural strength of 380 MPa. Finally, the chemical stability in air of these materials was assessed.     

Thermoset/graphene polymer composites—A review of processing and properties

Polymer-carbon nanocomposites incorporate the exceptional properties of both the polymer matrices, such as low cost and simple processing, with the distinctive features of the carbon-based fillers, such as high electrical and thermal conductivities, and excellent mechanical properties. Various fillers like carbon black (CB), graphite, expanded graphite (EG), and carbon nanotubes (CNTs) are being used to produce materials with advanced properties. However, at high filler loading, these filler materials have some major challenges such as filler agglomeration. Recently, graphene has gained increased interest as an alternative filler to produce polymer nanocomposites with advanced characteristics. Thermosetting polymer composites with graphene fillers are being considered for multiple applications and are a subject of interest for researchers because of enhanced properties like excellent corrosion resistance and low density. This review outlines studies to improve the mechanical, electrical, and thermal properties of thermoset/graphene composites.     

Enhanced mechanical and tribological properties of oscillatory pressure sintered WC–GNPs composites

It remains as a challenge to develop binderless WC ceramics that integrate high mechanical properties and low friction wear. Here, we report the preparation of strong and tough WC ceramics with low wear rate by adding graphene nanoplatelets (GNPs) and using oscillatory pressure sintering (OPS) process. The introduced GNPs lead to the formation of nearly fully dense composites with the aid of an oscillatory pressure. The OPS-prepared WC–0.3-wt% GNPs composites reached a high flexural strength, hardness, and fracture toughness, being up to 1420 MPa, 24.9 GPa, and 6.89 MPa m^1/2, respectively. Moreover, a low friction wear rate of 3.17 × 10⁻⁷ mm³ N⁻¹ m⁻¹ is achieved for such composites, which can be ascribed to the formation of a friction lubrication film during dry sliding friction process and their higher mechanical properties.     

ZrB2 – SiC ceramics: Residual stresses and mechanical properties

The stress-strain state of ZrB₂-SiC ultra-high-temperature ceramics, produced using commercial powders with different impurity levels, was investigated by X-ray diffraction. Upon analysis of ZrB₂ and SiC diffraction lines shift, the level of thermal stresses (strains) of the different phases was determined. An increase of internal stresses in ceramics with rising viscous-brittle transition temperatures, T_ve, was attributed to increased grain boundary strength. Ceramics, for which high T_ve and high level of internal stresses were estimated, exhibited high strength, up to 700 MPa at 1400 °C. A field of compressive thermal stresses in the matrix phase resulted to be necessary for achieving high strength at low-temperatures. On the contrary, the presence of low-melting impurities at the grain boundaries negatively impacted on the stress level in ZrB₂ boundaries in the high temperature regime.     

An investigation of thermal and mechanical properties of synthesised polyamide-6/γ-alumina composites

Abstract

Polyamide based composites were formed by melt blending of polyamide 6 (PA6) with a γ) -alumina powder toughened with ethylene–octene copolymer grafted by maleic anhydride (EOC-g-MAH) and also without EOC in a corotating twin screw extruder. Mechanical properties, morphological structure and thermal stability of toughened PA6 (PA6-g-EOC) and PA6-g-EOC/alumina composites were investigated in this study.To study the effect of powder loading of γ-alumina on the mechanical properties of the composites such as tensile strength, modulus of elasticity, break point and impact strength, varied amounts of 5, 10 and 15?wt-% were deployed. The toughened PA6–γ-alumina composites, i.e. blended by EOC-g-MAH, revealed higher impact strength and more toughness compared to that of the PA6–γ-alumina composites without EOC-g-MAH. Morphology of the composites was investigated by scanning electron microscopy (SEM) from the as moulded specimens. Micrographs showed a fine dispersion of γ-alumina particles in polyamide matrix due to appropriate mixing. Furthermore, thermal stability and degradation characteristics of the toughened PA6–γ-alumina composites were measured by thermogravimetric analysis. The addition of γ-alumina into the polyamide matrix showed an increase in thermal resistance so that thermal stability was increased by a rise in the powder loading.     

Processing and mechanical properties of hot-pressed zirconium diboride – zirconium carbide ceramics

ZrB₂ was mixed with 0.5 wt% carbon and up to 10 vol% ZrC and densified by hot-pressing at 2000 °C. All compositions were > 99.8% dense following hot-pressing. The dense ceramics contained 1–1.5 vol% less ZrC than the nominal ZrC addition and had between 0.5 and 1 vol% residual carbon. Grain sizes for the ZrB₂ phase decreased from 10.1 µm for 2.5 vol% ZrC to 4.2 µm for 10 vol% ZrC, while the ZrC cluster size increased from 1.3 µm to 2.2 µm over the same composition range. Elastic modulus was ~505 GPa and toughness was ~2.6 MPa·m^½ for all compositions. Vickers hardness increased from 14.1 to 15.3 GPa as ZrC increased from 2.5 to 10 vol%. Flexure strength increased from 395 MPa for 2.5 vol% ZrC to 615 MPa for 10 vol% ZrC. Griffith-type analysis suggests ZrB₂ grain pullout from machining as the strength limiting flaw for all compositions.     

A review of graphene-oxide/metal–organic framework composites materials: characteristics,preparation and applications

Journal of Porous Materials - Graphene-oxide (GO) is an oxidized derivative of graphene. GO has a large number of oxygen-containing functional groups, including hydroxyl, carboxyl, and epoxy...     

Microstructure and mechanical properties of Al2O3–YSZ spherical polycrystalline composites

The mechanical behavior and microstructure of highly densified, spherically shaped, polycrystalline Al₂O₃–YSZ composites, processed from pseudoboehmite powders by sol–gel is reported here. Processing was carried out by combining nanometric sized α-Al₂O₃ (120 nm) seeds and YSZ particles of tetragonal structure. The YSZ particles were homogeneously distributed in a coarse-grained matrix of alumina, both inside grains and along grain boundaries. Fracture surfaces, achieved by impact tests showed toughening effects of the zirconia particles. The tetragonality of the YSZ phase stability even after fracture events and fracture toughness measurements by Vickers indentation, where the crack tip interacts with YSZ particles, are all provided and discussed. The local mechanical properties, such as elastic modulus, indentation hardness and the onset of plastic deformation or fracture contact pressure of both YSZ particles and the Al₂O₃ matrix were quantified by nanoindentation. Evidence of coercive contact pressure was observed in YSZ from indentation stress–strain curves.     

Investigation of microstructure and mechanical properties of Cu/Ti–B–SiCp hybrid composites

In this study, Cu/Ti–B-SiC_p hybrid composite materials were produced by powder metallurgy method using three different sintering temperatures (950, 1000, 1050 °C). The optimum sintering temperature of Cu main matrix composites reinforced with Ti–B-SiC_p reinforcement materials at 2-4-6-8 wt.% were determined and their microstructure and mechanical properties were investigated. As a result of microstructure studies, it was determined that reinforcement elements have a homogeneous interface in the main matrix. The hardness of the produced composites was determined by the Brinell hardness method. The highest hardness value (77.74 HB) was determined in the sample with 6 wt% reinforcement ratio. In the tensile and three point bending tests, maximum strength values (112.96 MPa, 37.76 MPa) were found in samples with a reinforcement ratio of 4 wt%. It was determined that increasing reinforcement ratios and sintering temperature made a positive contribution to the hybrid composite materials produced.     

Improvement of mechanical properties of macroporous β-tricalcium phosphate bioceramic scaffolds with uniform and interconnected pore structures

The biocompatible and degradable macroporous bioceramic scaffolds with high mechanical properties and interconnected porous structures play an important role in hard tissue regeneration and bone tissue engineering applications. In this study, the improvement of mechanical properties of macroporous β-tricalcium phosphate [β-Ca₃(PO₄)₂, β-TCP] bioceramic scaffolds with uniform macropore size and interconnected pores were fabricated by impregnation of the synthesized β-TCP nano-powder slurry into polymeric frames. The microstructures, mechanical properties and in vitro degradation of the fabricated samples were investigated. For a comparison, β-TCP scaffolds were also fabricated from commercial micro-size powders under the same conditions. The resultant scaffolds showed porosities ∼65% with uniform macropore size ranging from 400 to 550 μm and interconnected pore size ∼100 μm. The compressive strength of the samples fabricated from nano-size powders reached 10.87 MPa, which was almost twice as high as those fabricated from commercial micro-size powders, and was comparable to the high-end value (2–10 MPa) of human cancellous bone. Furthermore, the degradation of the β-TCP bioceramics fabricated from nano-size powders was apparently lower than those fabricated from commercial micro-size powders, suggesting the possible control of the degradation of the scaffolds by regulating initial powder size. Regarding the excellent mechanical properties and porous structures, the obtained macroporous β-TCP bioceramic scaffolds can be used in hard tissue regeneration and bone tissue engineering applications.     

Structures and mechanical properties of electrospun cellulose nanofibers/poly(ε-caprolactone) composites

Poly(ε-caprolactone) (PCL) is one of the ecofriendly biodegradable polymers with excellent moldability but with rather low mechanical properties especially for the industrial and biomedical use. In this research, to overcome the problem, the two types of cellulose nanofibers, the cellulose acetate nanofibers (CA-NF) and the cellulose nanofibers (C-NF), were composited into PCL for the enhancement of the mechanical properties of PCL. CA-NF were prepared by electrospinning and converted into C-NF afterward by deacetylation. It was found that the Young's modulus of the CA-NF/PCL composite at the fiber concentration of 35 wt% significantly increased by ~3 times as compared with that of neat PCL, whereas C-NF/PCL of the same fiber concentration also increased by ~4.5 times. It was also found that the Young's moduli of CA-NF/PCL nearly reached the theoretical values calculated by the equation suggested by Tsai, but that the Young's moduli of C-NF/PCL could not reach the theoretical values. It indicates that CA-NF possessed better compatibility with PCL than C-NF, agreeing well with the fracture-surface analyses of the two composites by the scanning electron microscopy.     

Microstructure and mechanical properties of superplastically deformed silicon nitride–silicon oxynitride in situ composites

Silicon nitride–silicon oxynitride in situ composites were fabricated by plane-strain-compressing dense silicon nitrides, starting from 93 wt.% ultrafine β-Si₃N₄ and 7 wt.% cordierite, at 1600 °C under a constant load of 40 MPa and subsequent annealing at 1750 °C for 30 min. The resulting composites featured a microstructure of elongated Si₂N₂O grains (∼0.64 μm in diameter and ∼5.5 in aspect ratio) dispersed in a fine-grained β-Si₃N₄ matrix (∼ 0.30μm in diameter and ∼3.5 in aspect ratio), with the amount of Si₂N₂O, which had relatively strong textures, being strain-dependent. The mechanical properties were found to be improved due to the development of elongated Si₂N₂O grains, the texture formation, and the coarsening of β-Si₃N₄. Fracture toughness, however, was still low (∼5.2 MPa m^1/2) for these composites in comparison to self-reinforced silicon nitrides, resulted from the strong Si₂N₂O-matrix interfacial bond and nearly equiaxed β-Si₃N₄ with a small grain size. Anticipated property anisotropies were clearly observed as a result of the textured microstructure.