Catalytic decomposition of N2O over CeO2 promoted Co3O4 spinel catalyst

A series of CeO₂ promoted cobalt spinel catalysts were prepared by the co-precipitation method and tested for the decomposition of nitrous oxide (N₂O). Addition of CeO₂ to Co₃O₄ led to an improvement in the catalytic activity for N₂O decomposition. The catalyst was most active when the molar ratio of Ce/Co was around 0.05. Complete N₂O conversion could be attained over the CoCe0.05 catalyst below 400 °C even in the presence of O₂, H₂O or NO. Methods of XRD, FE-SEM, BET, XPS, H₂-TPR and O₂-TPD were used to characterize these catalysts. The analytical results indicated that the addition of CeO₂ could increase the surface area of Co₃O₄, and then improve the reduction of Co³⁺ to Co²⁺ by facilitating the desorption of adsorbed oxygen species, which is the rate-determining step of the N₂O decomposition over cobalt spinel catalyst. We conclude that these effects, caused by the addition of CeO₂, are responsible for the enhancement of catalytic activity of Co₃O₄.     

Potassium-doped Co3O4 catalyst for direct decomposition of N2O

Direct decomposition of nitrous oxide (N₂O) on K-doped Co₃O₄ catalysts was examined. The K-doped Co₃O₄ catalyst showed a high activity even in the presence of water. In the durability test of the K-doped Co₃O₄ catalyst, the activity was maintained at least for 12 h. It was found that the activity of the K-doped Co₃O₄ catalyst strongly depended on the amount of K in the catalyst. In order to reveal the role of the K component on the catalytic activity, the catalyst was characterized by XRD, XPS, TPR and TPD. The results suggested that regeneration of the Co²⁺ species from the Co³⁺ species formed by oxidation of Co²⁺ with the oxygen atoms formed by N₂O decomposition was promoted by the addition of K to the Co₃O₄ catalyst.     

Effect of Mn/Al ratio in Co–Mn–Al mixed oxide catalysts prepared from hydrotalcite-like precursors on catalytic decomposition of N2O

The Co–Mn–Al mixed oxide catalysts were prepared by thermal decomposition of hydrotalcite-like precursors with Co/(Mn + Al) molar ratio of 2 and Mn/Al molar ratio varying from 0 to 2. The obtained catalysts were characterized by powder XRD, XPS, BET surface area and TPR measurements and tested in N₂O decomposition. The most active Co4MnAl catalyst exhibited both the optimum Mn/Al molar ratio and the optimum amount of components reducible in the temperature region in which the catalytic reaction proceeds (350–450 °C).     

Cu-Mn氧化物催化N_2O直接分解性能

分别以Cu(NO_3)_2·3H_2O和50%Mn(NO_3)_2水溶液为铜源和锰源,K_2CO_3为沉淀剂,采用沉淀法和共沉淀法制备单一Cu、Mn氧化物催化剂和Cu-Mn-O复合氧化物催化剂,用于催化N_2O直接分解反应,并利用N_2物理吸附-脱附、XRD、FT-IR和TPR等进行表征。结果表明,单一Cu和Mn氧化物分别以体相CuO和Mn2O_3物相形式存在,Cu-Mn-O复合氧化物中除形成CuMn_2O_4尖晶石物相外,还有一定量小晶粒CuO,较单一氧化物具有更加优异的还原性能,表现出较高的催化N_2O直接分解活性。在空速10 000 h~(-1)和N_2O体积分数0.1%条件下,Cu-Mn-O复合氧化物催化剂可在440℃催化N_2O完全分解,分别较单一Cu和Mn氧化物催化剂降低了40℃和60℃。     

N2O catalytic decomposition over various spinel-type oxides

Various spinel-type catalysts AB₂O₄ (where A = Mg, Ca, Mn, Co, Ni, Cu, Cr, Fe, Zn and B = Cr, Fe, Co) were prepared and characterized by XRD, BET, TEM and FESEM-EDS. The performance of these catalysts towards the decomposition of N₂O to N₂ and O₂ was evaluated in a temperature programmed reaction (TPR) apparatus in the absence and the presence of oxygen. Spinel-type oxides containing Co at the B site were found to provide the best activity. The half conversion temperature of nitrous oxide over the MgCo₂O₄ catalyst was 440 °C and 470 °C in the absence and presence of oxygen, respectively (GHSV = 80,000 h⁻¹).

On the grounds of temperature programmed oxygen desorption (TPD) analyses as well as of reactive runs, the prevalent activity of the MgCo₂O₄ catalyst could be explained by its higher concentration of suprafacial, weakly chemisorbed oxygen species, whose related vacancies contribute actively to nitrous oxide catalytic decomposition. This indicates the way for the development of new, more active catalysts, possibly capable of delivering at low temperatures amounts of these oxygen species even higher than those characteristic of MgCo₂O₄.     

动物骨源羟磷灰石负载Co3O4用于N2O催化分解

通过焙烧猪骨和鸡骨获得羟磷灰石(nHAP)载体,并采用浸渍法制备Co3O4/nHAP催化剂。采用XRD、N2物理吸附-脱附、FT-IR和H2-TPR等对催化剂进行表征,在连续流动微反装置上考察催化剂催化分解N2O的性能。结果表明,相比于鸡骨源Co3O4/nHAP催化剂,以猪骨源HAP为载体的催化剂因其较大的比表面积以及较小的Co3O4粒径尺寸,提供了更多的活性位点。特别是猪骨源Co3O4/nHAP催化剂中适量的K、Na等元素促进了Co^3+到Co^2+的还原,削弱了Co-O键,使催化剂的催化活性显著提高。     

负载型钴锰复合金属氧化物催化剂催化分解N_2O

以ZrO_2为载体,采用浸渍法制备负载型钴锰复合金属氧化物催化剂,研究催化剂活性组分负载量、Co与Mn物质的量比、焙烧条件及含H_2O气氛对N_2O转化率的影响。结果表明,催化剂最佳制备条件为:活性组分Co负载质量分数3%,Co与Mn物质的量比为1∶1,焙烧升温速率2℃·min-1,焙烧温度900℃。该条件制备的负载型钴锰复合金属氧化物催化剂在反应温度850℃时,N_2O转化率达98.7%。当反应气氛中H_2O体积分数小于20%条件下,850℃时N_2O转化率高于90%,表明催化剂具有较强的抗水性能。     

Development of a new Rh/TiO2–sepiolite monolithic catalyst for N2O decomposition

Monolithic catalysts based on Rh/TiO₂–sepiolite were developed and tested in the decomposition of N₂O traces. Several effects such as the presence of NO, O₂ and NO + O₂ in the gas mixture, the catalysts pre-treatment and the metal loading were evaluated. The system was extremely sensitive to the amount of rhodium, passing through a maximum in the catalytic activity at a Rh content of 0.2 wt.%. It has been demonstrated that both NO and O₂ compete for the same adsorption sites as N₂O; however, this effect was not as severe as for other previously reported Rh systems. For NO + O₂ gas mixtures the inhibition effect was stronger than when only NO or O₂ was present. Analysis of the pre-reduced sample by XPS showed Rh mainly in the metal state, even after treatment with N₂O + O₂ mixtures, suggesting that the oxygen consumption observed in the Temperature Programmed Reaction experiments was related to the oxygen uptake by vacancies in the support. The presence of sepiolite in the support preparation and its role as a matrix over which TiO₂ particles were distributed, seems to play an important effect in the migration process of oxygen species through the support vacancies. The Rh/TiO₂ monolithic system is an attractive alternative for the elimination of N₂O traces from stationary sources due to the combination of high catalytic activity with a low pressure drop and optimum textural/mechanical properties.     

N2O decomposition over wet- and solid-exchanged Fe-ZSM-5 catalysts

The N₂O decomposition activity of Fe-ZSM-5 strongly depends on the iron content and the preparation methods, including wet (WIE) and solid state ion exchanges (SSIE). The state of Fe species formed on the surface of a series of Fe-ZSM-5 catalysts containing a variety of Fe contents with respect to the preparation method and their role for N₂O decomposition activity have been systematically examined. The general trend for the decomposition activity of Fe-ZSM-5-SSIE is higher than that of Fe-ZSM-5-WIE, indicating the formation of a distinctive local structure of Fe on the catalyst surface during the course of the ion-exchange procedure. Based upon the Fourier transformed Fe K-edge EXAFS spectra for the series of Fe-ZSM-5-SSIE and -WIE catalysts, most of the Fe species on the surface of Fe-ZSM-5-SSIE with high Fe loading are well dispersed in the form of oxygen-bridged binuclear Fe species. The turnover frequency (TOF) for N₂O decomposition under dry and wet conditions has been confirmed assuming that Fe-ZSM-5-SSIE samples with Fe/Al = 0.20 and Fe/Al = 0.65 only contain mononuclear and binuclear Fe species, respectively, as active reaction species on their surface. The high performance of Fe-ZSM-5-SSIE may be mainly due to the formation of the binuclear Fe species onto its surface during the preparation of the catalyst.     

Mechanism of N2O decomposition over a Rh black catalyst studied by a tracer method: The reaction of N2O with O(a)

N₂O decomposition on an unsupported Rh catalyst has been studied using tracer technique in order to reveal the reaction mechanism. N₂¹⁶O was pulsed onto ¹⁸O/oxidized Rh catalyst at 220°C and desorbed O₂ molecules (m/e=32,34,36) were monitored by means of mass spectrometer. The ¹⁸O fraction in the desorbed dioxygen was the same value as that on the surface oxygen. The result shows that the O₂ molecules desorb via Langmuir–Hinshelwood mechanism, i.e., the desorption of dioxygen through the recombination of adsorbed oxygen. On the other hand, TPD measurements in He showed that desorption of oxygen from the Rh black catalyst occurred at the higher temperatures. Therefore, reaction-assisted desorption of oxygen during N₂O decomposition reaction at the low temperature was proposed.     

Co-Cu-Ce-Fe/γ-Al_2O_3催化剂催化分解N_2O的性能

以等体积浸渍法制备γ-Al_2O_3负载的Co、Cu、Ce和Fe氧化物催化剂,利用正交试验设计实验条件,采用XRD、BET和H_2-TPR等对催化剂进行表征,并考察活性组分对催化剂催化分解N_2O活性的影响。结果表明,催化剂具有尖晶石结构,其BET比表面积随着金属氧化物负载量增加而降低。催化剂中铜的氧化物可以降低还原峰温度,进而明显提高催化活性,Co和Fe的加入对活性有一定的提高,Ce对催化活性没有明显影响。     

Superior performance of Ir-substituted hexaaluminate catalysts for N2O decomposition

Novel Ir-substituted hexaaluminate catalysts were developed for the first time and used for catalytic decomposition of high concentration of N₂O. The catalysts were prepared by one-pot precipitation and characterized by X-ray diffraction (XRD), N₂-adsorption, scanning electronic microscopy (SEM) and temperature-programmed reduction (H₂-TPR). The XRD results showed that only a limited amount of iridium was incorporated into the hexaaluminate lattice by substituting Al³⁺ to form BaIr_xFe_1−xAl₁₁O₁₉ after being calcined at 1200 °C, while the other part of iridium existed as IrO₂ phase. The activity tests for high concentration (30%, v/v) of N₂O decomposition demonstrated that the BaIr_xFe_1−xAl₁₁O₁₉ hexaaluminates exhibited much higher activities and stabilities than the Ir/Al₂O₃-1200, and the pre-reduction with H₂ was essential for activating the catalysts. By comparing BaIr_xFe_1−xAl₁₁O₁₉ with BaIr_xAl_12−xO₁₉ (x = 0–0.8), it was found that iridium was the active component in the N₂O decomposition and the framework iridium was more active than the large IrO₂ particles. On the other hand, Fe facilitated the formation of hexaaluminate as well as the incorporation of iridium into the framework.     

Co3O4–CeO2 mixed oxide-based catalytic materials for diesel soot oxidation

Co₃O₄–CeO₂ type mixed oxide catalyst compositions have been prepared by using co-precipitation method and, their catalytic activity towards diesel particulate matter (PM)/carbon oxidation has been evaluated under both loose and tight contact conditions. These catalysts show excellent catalytic activity for PM/carbon oxidation, despite their low surface area. The activation energy observed for non-catalyzed and catalyzed reactions are 163 kJ/mol and 140 kJ/mol, respectively, which also confirm the catalytic activity of catalyst for carbon/soot oxidation. The promotional effects of an optimum amount of cobalt oxide incorporation in ceria and presence of a small amount of potassium appears to be responsible for the excellent soot oxidation activity of this mixed oxide type material. The catalytic materials show good thermal stability, while their low cost will also add to their potential for practical applications.     

分子筛催化剂上N2O催化分解的研究进展

氧化亚氮(N2O)会造成温室效应和臭氧层破坏,N2O的控制日益引起关注。催化分解技术是控制N2O的有效手段,分别对Fe基、Cu基和Co基分子筛催化剂催化分解N2O的研究现状进行总结和评述,并展望未来发展方向。     

Self oscillatory behaviour in N2O decomposition over Co-ZSM-5 catalysts

Isothermal oscillations developed during N₂O decomposition over Co-ZSM-5 catalysts with different Si/Al ratios have been investigated. Spontaneous oscillations were observed between 350 and 450 °C. The maximum amplitude has been obtained for the catalysts having Si/Al of 40 and 50. The activation energies of the obtained oscillations were calculated in respect to cobalt concentration. The results showed that the E_a values increase linearly with an increasing Si/Al ratio of the zeolite. For Co-ZSM-5 catalyst (Si/Al = 25), increasing cobalt content in the catalyst led to a decrease in the frequency as well as the amplitude of the oscillations. Meanwhile, the increase in the E_a values was observed. The calculated reaction rate was found to be first order with respect to nitrous oxide concentration. Moreover, the developed oscillations were found to be sensitive to inlet N₂O concentration, catalyst weight and milling time duration. Decreasing the N₂O inlet concentration as well as the catalyst weight and increasing the milling time would lead to a quenching of the developed oscillations.     

Cu-Ce-O/γ-Al_2O_3的CO氧化性能

采用柠檬酸络合法制备一系列不同铜铈比的Cu-Ce-O/γ-Al_2O_3催化剂,用XRD、H2-TPR对其进行表征,采用连续固定床微反装置对Cu-Ce-O/γ-Al_2O_3催化剂CO催化氧化活性进行评价。结果表明,Cu-Ce-O/γ-Al_2O_3催化剂的XRD图谱中除归属于γ-Al_2O_3的晶相峰外,还出现CuO和CeO_2的晶相峰。高温水热引起活性组分CeO_2的晶粒聚集、长大和尖晶石结构CuAl2O4物质的生成;CuO-CeO_2之间的共生共存与相互作用,使得Cu-Ce-O/γ-Al_2O_3催化剂中具有非完整结构的[Cu2+1-xCu+x][O1-12x12x]增多,Cu+离子和氧空位增多,有利于其H2-TPR还原峰温度向低温区偏移,有利于提高其CO的催化氧化活性,使得Cu-Ce-O/γ-Al_2O_3催化剂的TCO50和TCO90降低。Cu与Ce物质的量比为5∶5制备的Cu-Ce-O/γ-Al_2O_3-55催化剂的TCO50和TCO90分别降至最低的162℃和199℃,表明此时的Cu-Ce-O协同效应最佳;CuO-CeO_2二相的共生共存与相互作用有利于减少高温水热环境下活性组分的聚集和晶粒长大,有利于Cu-Ce-O/γ-Al_2O_3催化剂能够保持较高的CO催化氧化活性。     

负载型RuO_2/Me_xO_y(Me=La,Mg,Al)催化剂催化分解N_2O

采用共沉淀法制备LaMgAlO(简称Me_xO_y)复合金属氧化物,以Me-xO_y为载体,采用浸渍法制备系列负载型RuO_2/Me_xO_y催化剂,应用BET、TEM、XRF和SEM对代表性样品进行表征。结果表明,实验条件下,RuO_2负载质量分数2.0%时比较合适,在气体混合物中含有氧和少量水蒸汽条件下,催化剂具有较好的催化分解N_2O稳定性。     

Micro-kinetic analysis of direct N2O decomposition over steam-activated Fe-silicalite from transient experiments in the TAP reactor

Mechanistic and kinetic aspects of the direct decomposition of N₂O over steam-activated Fe-silicalite were investigated by transient experiments in vacuum (N₂O peak pressure of ca. 10 Pa) using the temporal analysis of products (TAP) reactor in the temperature range of 773–848 K. The transient responses of N₂O, N₂, and O₂ obtained upon N₂O decomposition were fitted to different micro-kinetic models. Through model discrimination it was concluded that both free iron sites and iron sites with adsorbed mono-atomic oxygen (*O) species are active for N₂O decomposition. Oxygen formation occurs via decomposition of bi-atomic (*O₂) oxygen species adsorbed over the iron site. This bi-atomic oxygen species originates from another bi-atomic oxygen species (O*O), which is initially formed via interaction of N₂O with iron site possessing mono-atomic oxygen species (*O). Based on our modeling, the recombination of two mono-atomic oxygen (*O) species or direct O₂ formation via reaction of N₂O with *O can be excluded as potential reaction pathways yielding gas-phase O₂. The simulation results predict that the overall rate of N₂O decomposition is controlled by regeneration of free iron sites via a multi-step oxygen formation at least below 700 K.     

Mechanistic insights into the formation of N2O and N2 in NO reduction by NH3 over a polycrystalline platinum catalyst

The reaction pathways of N₂ and N₂O formation in the direct decomposition and reduction of NO by NH₃ were investigated over a polycrystalline Pt catalyst between 323 and 973 K by transient experiments using the temporal analysis of products (TAP-2) reactor. The interaction between nitric oxide and ammonia was studied in the sequential pulse mode applying ¹⁵NO. Differently labelled nitrogen and nitrous oxide molecules were detected. In both, direct NO decomposition and NH₃–NO interaction, N₂O formation was most marked between 573 and 673 K, whereas N₂ formation dominated at higher temperatures. An unusual interruption of nitrogen formation in the ¹⁵NO pulse at 473 K was caused by an inhibiting effect of adsorbed NO species. The detailed analysis of the product distribution at this temperature clearly indicates different reaction pathways leading to the product formation. Nitrogen formation occurs via recombination of nitrogen atoms formed by dissociation of nitric oxide or/and complete dehydrogenation of ammonia. N₂O is formed via recombination of adsorbed NO molecules. Additionally, both products are formed via interactions between adsorbed ammonia fragments and nitric oxide.     

Characteristics of Fe-exchanged natural zeolites for the decomposition of N2O and its selective catalytic reduction with NH3

Natural zeolites obtained from various regions of Turkey and their iron-exchanged forms were characterised by XRD, BET, H₂-TPR and NH₃-TPD methods. Transient experiments with N₂O showed that the iron introduced into natural zeolites have appreciable oxygen deposition capacity due to isolated iron species involved. Atomic surface oxygen species in these zeolites are formed at 250 °C, which is released through increasing the temperature until 900 °C, similar to Fe-containing ZSM-5 zeolite. The steady-state experiments indicate that the iron-containing zeolite of the Yavu-Sivas region, in particular, has high activity in selective catalytic reduction of N₂O with NH₃ as a consequence of isolated cationic and/or dimeric iron content.