Hybrid Solar Cells Using HgTe Nanocrystals and Nanoporous TiO2 Electrodes

HgTe nanocrystals are demonstrated to increase the photon‐harvesting efficiency of hybrid solar cells over a broad spectral region between 350 and 1500 nm. Devices combining two solar cell concepts, a solid‐state nanocrystal‐sensitized solar cell and a nanocrystal/polymer‐blend solar cell, are described. These devices give incident photon to current efficiencies up to 10 % at around 550 nm monochromatic irradiation and short‐circuit current densities of 2 mA cm^–2 under simulated AM1.5 (100 mW cm^–2) illumination (AM: air mass).     

Elaboration of P3HT/CNT/PCBM Composites for Organic Photovoltaic Cells

This Full Paper focuses on the preparation of single‐walled or multi‐walled carbon nanotube solutions with regioregular poly(3‐hexylthiophene) (P3HT) and a fullerene derivative 1‐(3‐methoxycarbonyl) propyl‐1‐phenyl[6,6]C₆₁ (PCBM) using a high dissolution and concentration method to exactly control the ratio of carbon nanotubes (CNTs) to the P3HT/PCBM mixture and disperse the CNTs homogeneously throughout the matrix. The CNT/P3HT/PCBM composites are deposed using a spin‐coating technique and characterized by absorption and fluorescence spectroscopy and by atomic force microscopy to underline the structure and the charge transfer between the CNTs and P3HT. The performance of photovoltaic devices obtained using these composites as a photoactive layer mainly show an increase of the short circuit current and a slight decrease of the open circuit voltage which generally leads to an improvement of the solar cell performances to an optimum CNT percentage. The best results are obtained with a P3HT/PCBM (1 : 1) mixture with 0.1 wt % multi‐walled carbon nanotubes with an open circuit voltage (V_oc) of 0.57 V, a current density at the short‐circuit (I_sc) of 9.3 mA cm^–2 and a fill factor of 38.4 %, which leads to a power conversion efficiency of 2.0 % (irradiance of 100 mW cm^–2 spectroscopically distributed following AM1.5).     

Charge Transport and Photocurrent Generation in Poly(3‐hexylthiophene): Methanofullerene Bulk‐Heterojunction Solar Cells

The effect of controlled thermal annealing on charge transport and photogeneration in bulk‐heterojunction solar cells made from blend films of regioregular poly(3‐hexylthiophene) (P3HT) and methanofullerene (PCBM) has been studied. With respect to the charge transport, it is demonstrated that the electron mobility dominates the transport of the cell, varying from 10^–8 m² V^–1 s^–1 in as‐cast devices to ≈3 × 10^–7 m² V^–1 s^–1 after thermal annealing. The hole mobility in the P3HT phase of the blend is dramatically affected by thermal annealing. It increases by more than three orders of magnitude, to reach a value of up to ≈ 2 × 10^–8 m² V^–1 s^–1 after the annealing process, as a result of an improved crystallinity of the film. Moreover, upon annealing the absorption spectrum of P3HT:PCBM blends undergo a strong red‐shift, improving the spectral overlap with solar emission, which results in an increase of more than 60 % in the rate of charge‐carrier generation. Subsequently, the experimental electron and hole mobilities are used to study the photocurrent generation in P3HT:PCBM devices as a function of annealing temperature. The results indicate that the most important factor leading to a strong enhancement of the efficiency, compared with non‐annealed devices, is the increase of the hole mobility in the P3HT phase of the blend. Furthermore, numerical simulations indicate that under short‐circuit conditions the dissociation efficiency of bound electron–hole pairs at the donor/acceptor interface is close to 90 %, which explains the large quantum efficiencies measured in P3HT:PCBM blends.     

Measuring Domain Sizes and Compositional Heterogeneities in P3HT‐PCBM Bulk Heterojunction Thin Films with 1H Spin Diffusion NMR Spectroscopy

The application of ¹H spin diffusion nuclear magnetic resonance (NMR) is expanded to polymer‐fullerene blends for bulk heterojunction (BHJ) organic photovoltaics (OPV) by developing a new experimental methodology for measuring the thin films used in poly‐3‐hexylthiophene–phenyl C61‐butyric acid methyl ester (P3HT‐PCBM) OPV devices and by creating an analysis framework for estimating domain size distributions. It is shown that variations in common P3HT‐PCBM BHJ processing parameters such as spin‐coating speed and thermal annealing can significantly affect domain size distributions, which in turn affect power conversion efficiency. ¹H spin diffusion NMR analysis reveals that films spin‐cast at fast speeds in dichlorobenzene are primarily composed of small (<10 nm) domains of each component; these devices exhibit low power conversion efficiencies (η = 0.4%). Fast‐cast films improve substantially by thermal annealing, which causes nanometer‐scale coarsening leading to higher efficiency (η = 2.2%). Films spin‐cast at slow speeds and then slowly dried exhibit larger domains and even higher efficiencies (η = 2.6%), but do not benefit from thermal annealing. The ¹H spin diffusion NMR results show that a significant population of domains tens of nanometers in size is a common characteristic of samples with higher efficiencies.     

Conversion efficiency improvement mechanisms of polymer solar cells by balance electron–hole mobility using blended P3HT:PCBM:pentacene active layer

To improve the power conversion efficiency of polymer solar cells, the blended P3HT:PCBM:pentacene active layer was used to balance hole–electron mobility and roughen surface. Using space-charged-limited current model to analyze the hole-only devices and the electron-only devices, the P3HT:PCBM:pentacene (weight ratio = 1:0.8:0.09) active layer exhibited balance hole–electron mobility. Compared with the power conversion efficiency of 3.46% of the conventional polymer solar cells using P3HT:PCBM (1:0.8) active layer, the power conversion efficiency of 4.42% was obtained. In other words, the power conversion efficiency was improved about 27.5%.     

Annealing‐Free High Efficiency and Large Area Polymer Solar Cells Fabricated by a Roller Painting Process

Polymer solar cells are fabricated by a novel solution coating process, roller painting. The roller‐painted film – composed of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) – has a smoother surface than a spin‐coated film. Since the roller painting is accompanied by shear and normal stresses and is also a slow drying process, the process effectively induces crystallization of P3HT and PCBM. Both crystalline P3HT and PCBM in the roller‐painted active layer contribute to enhanced and balanced charge‐carrier mobility. Consequently, the roller‐painting process results in a higher power conversion efficiency (PCE) of 4.6%, as compared to that for spin coating (3.9%). Furthermore, annealing‐free polymer solar cells (PSCs) with high PCE are fabricated by the roller painting process with the addition of a small amount of octanedi‐1,8‐thiol. Since the addition of octanedi‐1,8‐thiol induces phase separation between P3HT and PCBM and the roller‐painting process induces crystallization of P3HT and PCBM, a PCE of roller‐painted PSCs of up to 3.8% is achieved without post‐annealing. A PCE of over 2.7% can also be achieved with 5 cm² of active area without post‐annealing.     

The Impact of Polymer Regioregularity on Charge Transport and Efficiency of P3HT:PCBM Photovoltaic Devices

The charge transport in pristine poly(3‐hexylthiophene) (P3HT) films and in photovoltaic blends of P3HT with [6,6]‐phenyl C61 butyric acid methyl ester (PCBM) is investigated to study the influence of charge‐carrier transport on photovoltaic efficiency. The field‐ and temperature dependence of the charge‐carrier mobility in P3HT of three different regioregularities, namely, regiorandom, regioregular with medium regioregularity, and regioregular with very high regioregularity are investigated by the time‐of‐flight technique. While medium and very high regioregularity polymers show the typical absorption features of ordered lamellar structures of P3HT in the solid state even without previous annealing, films of regiorandom P3HT are very disordered as indicated by their broad and featureless absorption. This structural difference in the solid state coincides with partially non‐dispersive transport and hole mobilities µ_h of around 10^?4 and 10^?5 cm² V^?1 s^?1 for the high and medium regioregularity P3HT, respectively, and a slow and dispersive charge transport for the regiorandom P3HT. Upon blending the regioregular polymers with PCBM, the hole mobilities are typically reduced by one order of magnitude, but they do not significantly change upon additional post‐spincasting annealing. Only in the case of P3HT with high regioregularity are the electron mobilities similar to the hole mobilities and the charge transport is, thus, balanced. Nonetheless, devices prepared from both materials exhibit similar power conversion efficiencies of 2.5%, indicating that very high regioregularity may not substantially improve order and charge‐carrier transport in P3HT:PCBM and does not lead to significant improvements in the power‐conversion efficiency of photovoltaic devices.     

Effects of Postproduction Treatment on Plastic Solar Cells

Efficiencies of organic solar cells based on an interpenetrating network of a conjugated polymer and a fullerene as donor and acceptor materials still need to be improved for commercial use. We have developed a postproduction treatment that improves the performance of solar cells based on poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PCBM) by means of a tempering cycle at elevated temperatures in which an external voltage is simultaneously applied, resulting in a significant increase of the short‐circuit current. Using this postproduction treatment, an enhancement of the short‐circuit current density, I_sc, to 8.5 mA cm^–2 under illumination with white light at an illumination intensity of 800 W m^–2 and an increase in external quantum efficiency (IPCE, incident photon to collected electron efficiency) to 70 % are demonstrated.     

A Simple and Effective Modification of PCBM for Use as an Electron Acceptor in Efficient Bulk Heterojunction Solar Cells

[6,6]‐phenyl‐C‐61‐butyric acid methyl ester (PCBM) and poly(3‐hexylthiophene) (P3HT) are the most widely used acceptor and donor materials, respectively, in polymer solar cells (PSCs). However, the low LUMO (lowest unoccupied molecular orbital) energy level of PCBM limits the open circuit voltage (V_oc) of the PSCs based on P3HT. Herein a simple, low‐cost and effective approach of modifying PCBM and improving its absorption is reported which can be extended to all fullerene derivatives with an ester structure. In particular, PCBM is hydrolyzed to carboxylic acid and then converted to the corresponding carbonyl chloride. The latter is condensed with 4‐nitro‐4’‐hydroxy‐α‐cyanostilbene to afford the modified fullerene F . It is more soluble than PCBM in common organic solvents due to the increase of the organic moiety. Both solutions and thin films of F show stronger absorption than PCBM in the range of 250–900 nm. The electrochemical properties and electronic energy levels of F and PCBM are measured by cyclic voltammetry. The LUMO energy level of F is 0.25 eV higher than that of PCBM. The PSCs based on P3HT with F as an acceptor shows a higher V_oc of 0.86 V and a short circuit current (J_sc) of 8.5 mA cm^?2, resulting in a power conversion efficiency (PCE) of 4.23%, while the PSC based on P3HT:PCBM shows a PCE of about 2.93% under the same conditions. The results indicate that the modified PCBM, i.e., F , is an excellent acceptor for PSC based on bulk heterojunction active layers. A maximum overall PCE of 5.25% is achieved with the PSC based on the P3HT: F blend deposited from a mixture of solvents (chloroform/acetone) and subsequent thermal annealing at 120 °C.     

High‐Performance Metal‐Free Solar Cells Using Stamp Transfer Printed Vapor Phase Polymerized Poly(3,4‐Ethylenedioxythiophene) Top Anodes

The use of vapor phase polymerized poly(3,4‐ethylenedioxythiophene) (VPP‐PEDOT) as a metal‐replacement top anode for inverted solar cells is reported. Devices with both i) standard bulk heterojunction blends of poly(3‐hexylthiophene) (P3HT) donor and 1‐(3‐methoxycarbonyl)‐propyl‐1‐phenyl‐(6,6)C₆₀ (PCBM) soluble fullerene acceptor and ii) hybrid inorganic/organic TiO₂/P3HT acceptor/donor active layers are studied. Stamp transfer printing methods are used to deposit both the VPP‐PEDOT top anode and a work function enhancing PEDOT:polystyrenesulphonate (PEDOT:PSS) interlayer. The metal‐free devices perform comparably to conventional devices with an evaporated metal top anode, yielding power conversion efficiencies of 3% for bulk heterojunction blend and 0.6% for organic/inorganic hybrid structures. These encouraging results suggest that stamp transfer printed VPP‐PEDOT provides a useful addition to the electrode materials tool‐box available for low temperature and non‐vacuum solar cell fabrication.     

Effect of Temperature and Illumination on the Electrical Characteristics of Polymer–Fullerene Bulk‐Heterojunction Solar Cells

The current–voltage characteristics of ITO/PEDOT:PSS/OC₁C₁₀‐PPV:PCBM/Al solar cells were measured in the temperature range 125–320 K under variable illumination, between 0.03 and 100 mW cm^–2 (white light), with the aim of determining the efficiency‐limiting mechanism(s) in these devices, and the temperature and/or illumination range(s) in which these devices demonstrate optimal performance. (ITO: indium tin oxide; PEDOT:PSS: poly(styrene sulfonate)‐doped poly(ethylene dioxythiophene); OC₁C₁₀‐PPV: poly[2‐methoxy‐5‐(3,7‐dimethyl octyloxy)‐1,4‐phenylene vinylene]; PCBM: phenyl‐C₆₁ butyric acid methyl ester.) The short‐circuit current density and the fill factor grow monotonically with temperature until 320 K. This is indicative of a thermally activated transport of photogenerated charge carriers, influenced by recombination with shallow traps. A gradual increase of the open‐circuit voltage to 0.91 V was observed upon cooling the devices down to 125 K. This fits the picture in which the open‐circuit voltage is not limited by the work‐function difference of electrode materials used. The overall effect of temperature on solar‐cell parameters results in a positive temperature coefficient of the power conversion efficiency, which is 1.9 % at T = 320 K and 100 mW cm^–2 (2.5 % at 0.7 mW cm^–2). The almost‐linear variation of the short‐circuit current density with light intensity confirms that the internal recombination losses are predominantly of monomolecular type under short‐circuit conditions. We present evidence that the efficiency of this type of solar cell is limited by a light‐dependent shunt resistance. Furthermore, the electronic transport properties of the absorber materials, e.g., low effective charge‐carrier mobility with a strong temperature dependence, limit the photogenerated current due to a high series resistance, therefore the active layer thickness must be kept low, which results in low absorption for this particular composite absorber.     

Three‐Dimensional Bulk Heterojunction Morphology for Achieving High Internal Quantum Efficiency in Polymer Solar Cells

Here, an investigation of three‐dimensional (3D) morphologies for bulk heterojunction (BHJ) films based on regioregular poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) is reported. Based on the results, it is demonstrated that optimized post‐treatment, such as solvent annealing, forces the PCBM molecules to migrate or diffuse toward the top surface of the BHJ composite films, which induces a new vertical component distribution favorable for enhancing the internal quantum efficiency (η_IQE ) of the devices. To investigate the 3D BHJ morphology, novel time‐of‐flight secondary‐ion mass spectroscopy studies are employed along with conventional methods, such as UV‐vis absorption, X‐ray diffraction, and high‐resolution transmission electron microscopy studies. The η_IQE of the devices are also compared after solvent annealing for different times, which clearly shows the effect of the vertical component distribution on the performance of BHJ polymer solar cells. In addition, the fabrication of high‐performance P3HT:PCBM solar cells using the optimized solvent‐annealing method is reported, and these cells show a mean power‐conversion efficiency of 4.12% under AM 1.5G illumination conditions at an intensity of 100 mW cm^?2.     

Optimization of Si NC/P3HT Hybrid Solar Cells

Silicon nanocrystals (Si NCs) are shown to be an electron acceptor in hybrid solar cells combining Si NCs with poly(3‐hexylthiophene) (P3HT). The effects of annealing and different metal electrodes on Si NC/P3HT hybrid solar cells are studied in this paper. After annealing at 150 °C, Si NC/P3HT solar cells exhibit power conversion efficiencies as high as 1.47%. The hole mobility in the P3HT phase extracted from space‐charge‐limited current measurements of hole‐only devices increases from 2.48 × 10^?10 to 1.11 × 10^?9 m² V^?1 s^?1 after annealing, resulting in better transport in the solar cells. A quenching of the open‐circuit voltage and short‐circuit current is observed when high work function metals are deposited as the cathode on Si NC/P3HT hybrid devices.     

Photo stability enhancement of Poly(3-hexylthiophene)-PCBM nanocomposites by addition of multi walled carbon nanotubes under ambient conditions

Poly(3-hexylthiophene)-Phenyl-C61-butyric acid methyl ester (P3HT–PCBM) composites find wide application in optoelectronic devices, especially bulk-hetero junction (BHJ) solar cells. These composites, even though could give efficient polymer solar cells with ∼4–5% power conversion efficiencies (PCE), a major problem of photo stability is associated with it and remains unsolved. P3HT–PCBM composite was found to be degrading on irradiation with ultraviolet radiation or a solar simulator providing AM1.5G illumination (1000 W m^–2, 72 ± 2 °C or 330 W m⁻², 25 °C), in presence of oxygen and moisture. Here, we have studied the photo stability of P3HT–PCBM under ambient conditions and showed that a new ternary composite, P3HT–PCBM–MWCNT (multi walled carbon nanotube) has superior photo stability even on extended UV–Vis exposure. A total of 7% (w/w) PCBM and 3% (w/w) MWCNT with respect to P3HT resulted in optimum stability. UV–Visible and fluorescence spectral analysis have been used to study the photo stability, both in solution state and solid/film state. Transmission electron micrograph (TEM) along with selected area electron diffraction (SAED) pattern and Field Emission Scanning Electron Microscopy (FE-SEM) micrographs have been used to show the well coating of MWCNT on P3HT–PCBM composite. Since MWCNT is one of the very important carbon based nanomaterial with several supreme characteristics, this new ternary composite has great importance for optoelectronic applications.     

Effect of Alkyl Side‐Chain Length on Photovoltaic Properties of Poly(3‐alkylthiophene)/PCBM Bulk Heterojunctions

The morphological, bipolar charge‐carrier transport, and photovoltaic characteristics of poly(3‐alkylthiophene) (P3AT):[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) blends are studied as a function of alkyl side‐chain length m, where m equals the number of alkyl carbon atoms. The P3ATs studied are poly(3‐butylthiophene) (P3BT, m = 4), poly(3‐pentylthiophene) (P3PT, m = 5), and poly(3‐hexylthiophene) (P3HT, m = 6). Solar cells with these blends deliver similar order of photo‐current yield (exceeding 10 mA cm^?2) irrespective of side‐chain length. Power conversion efficiencies of 3.2, 4.3, and 4.6% are within reach using solar cells with active layers of P3BT:PCBM (1:0.8), P3PT:PCBM (1:1), and P3HT:PCBM (1:1), respectively. A difference in fill factor values is found to be the main source of efficiency difference. Morphological studies reveal an increase in the degree of phase separation with increasing alkyl chain length. Moreover, while P3PT:PCBM and P3HT:PCBM films have similar hole mobility, measured by hole‐only diodes, the hole mobility in P3BT:PCBM lowers by nearly a factor of four. Bipolar measurements made by field‐effect transistor showed a decrease in the hole mobility and an increase in the electron mobility with increasing alkyl chain length. Balanced charge transport is only achieved in the P3HT:PCBM blend. This, together with better processing properties, explains the superior properties of P3HT as a solar cell material. P3PT is proved to be a potentially competitive material. The optoelectronic and charge transport properties observed in the different P3AT:PCBM bulk heterojunction (BHJ) blends provide useful information for understanding the physics of BHJ films and the working principles of the corresponding solar cells.     

Polymer Solar Cells Based on a Low‐Bandgap Fluorene Copolymer and a Fullerene Derivative with Photocurrent Extended to 850 nm

Polymer solar cells have been fabricated from a recently synthesized low band‐gap alternating polyfluorene copolymer, APFO‐Green2, combined with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) from organic solutions. External quantum efficiencies (EQEs) of the solar cells show an onset at 850 nm and a peak of > 10 % located at 650 nm, which corresponds to the extended absorption spectrum of the polymer. Photocurrent of 3.0 mA cm^–2, photovoltage of 0.78 V, and power conversion efficiency of 0.9 % have been achieved in solar cells based on this new low‐bandgap polymer under the illumination of air mass 1.5 (AM 1.5) (1000 W m^–2) from a solar simulator.     

High‐Performance Organic Solar Cells with Spray‐Coated Hole‐Transport and Active Layers

In this study, we report high performance organic solar cells with spray coated hole‐transport and active layers. With optimized ink formulations we are able to deposit films with controlled thickness and very low surface roughness (<10 nm). Specifically we deposit smooth and uniform 40 nm thick films of poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as well as films composed of a mixture of poly(3‐hexyl thiophene) (P3HT) and the C₆₀‐derivative (6,6)‐phenyl C61‐butyric acid methyl ester (PCBM) with thicknesses in the range 200–250 nm. To control film morphology, formation and thickness, the optimized inks incorporate two solvent systems in order to take advantage of surface tension gradients to create Marangoni flows that enhance the coverage of the substrate and reduce the roughness of the film. Notably, we achieve fill factors above 70% and attribute the improvement to an enhanced P3HT crystallization, which upon optimized post‐drying thermal annealing results in a favorable morphology. As a result, we could extend the thickness of the layer to several hundreds of nanometers without noticing a substantial decrease of the transport properties of the layer. By proper understanding of the spreading and drying dynamics of the inks we achieve spray coated devices with power conversion efficiency of 3.75%, with fill factor, short circuit current and open circuit voltage of 70%, 9.8 mA cm^?2 and 550 mV, respectively.     

Solution‐Processed Bulk‐Heterojunction Solar Cells Based on Monodisperse Dendritic Oligothiophenes

A novel family of soluble conjugated dendritic oligothiophenes (DOTs) as monodisperse 3D macromolecular architectures was characterized with respect to optical and redox properties in solution and in solid films. Band gaps of 2.5–2.2 eV, typical for organic semiconductors, were determined as well as HOMO/LUMO energy levels ideal for efficient electron transfer to acceptors such as [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) identifying them as suitable materials for solar cell applications. Solution‐processed bulk‐heterojunction solar cells using DOTs as electron donor and PCBM as acceptor were prepared and investigated. High open‐circuit voltages V_OC of 1.0 V and power‐conversion efficiencies up to 1.72% were obtained for the DOT‐based devices. The higher generations DOTs provide the highest efficiencies. Based on the monodispersity of the DOTs, an analysis of the molar ratio between donor and acceptor in the blended film was possible leading to an optimal value of five to six thiophene units per PCBM.     

Photovoltaic Devices: High‐Performance Organic Solar Cells with Spray Coated Hole‐Transport and Active Layers (Adv. Funct. Mater. 1/2011)

In this study, we report high performance organic solar cells with spray coated hole‐transport and active layers. With optimized ink formulations we are able to deposit films with controlled thickness and very low surface roughness (<10 nm). Specifically we deposit smooth and uniform 40 nm thick films of poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as well as films composed of a mixture of poly(3‐hexyl thiophene) (P3HT) and the C₆₀‐derivative (6,6)‐phenyl C61‐butyric acid methyl ester (PCBM) with thicknesses in the range 200–250 nm. To control film morphology, formation and thickness, the optimized inks incorporate two solvent systems in order to take advantage of surface tension gradients to create Marangoni flows that enhance the coverage of the substrate and reduce the roughness of the film. Notably, we achieve fill factors above 70% and attribute the improvement to an enhanced P3HT crystallization, which upon optimized post‐drying thermal annealing results in a favorable morphology. As a result, we could extend the thickness of the layer to several hundreds of nanometers without noticing a substantial decrease of the transport properties of the layer. By proper understanding of the spreading and drying dynamics of the inks we achieve spray coated devices with power conversion efficiency of 3.75%, with fill factor, short circuit current and open circuit voltage of 70%, 9.8 mA cm^?2 and 550 mV, respectively.     

Effect of Carbon Chain Length in the Substituent of PCBM‐like Molecules on Their Photovoltaic Properties

A series of [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM)‐like fullerene derivatives with the butyl chain in PCBM changing from 3 to 7 carbon atoms, respectively (F1–F5), are designed and synthesized to investigate the relationship between photovoltaic properties and the molecular structure of fullerene derivative acceptors. F2 with a butyl chain is PCBM itself for comparison. Electrochemical, optical, electron mobility, morphology, and photovoltaic properties of the molecules are characterized, and the effect of the alkyl chain length on their properties is investigated. Although there is little difference in the absorption spectra and LUMO energy levels of F1–F5, an interesting effect of the alkyl chain length on the photovoltaic properties is observed. For the polymer solar cells (PSCs) based on P3HT as donor and F1–F5, respectively, as acceptors, the photovoltaic behavior of the P3HT/F1 and P3HT/F4 systems are similar to or a little better than that of the P3HT/PCBM device with power conversion efficiencies (PCEs) above 3.5%, while the performances of P3HT/F3 and P3HT/F5‐based solar cells are poorer, with PCE values below 3.0%. The phenomenon is explained by the effect of the alkyl chain length on the absorption spectra, fluorescence quenching degree, electron mobility, and morphology of the P3HT/F1–F5 (1:1, w/w) blend films.