New poly(amide‐imide) syntheses. 24. Synthesis and properties of fluorinated poly(amide‐imide)s based on 2,2‐bis[4‐(trimellitimidophenoxy)phenyl]hexafluoropropane and various aromatic diamines

An imide ring‐performed dicarboxylic acid bearing one hexafluoroisopropylidene and two ether linkages between aromatic rings, 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane (II), was prepared from the condensation of 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane and trimellitic anhydride. A novel series of poly(amide‐imide)s having inherent viscosities of 0.72 ∼ 1.86 dL g⁻¹ was prepared by the triphenyl phosphite‐activated polycondensation from the diimide‐diacid (II) with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrolidone, pyridine, and calcium chloride. Several of the resulting polymers were soluble in polar amide solvents, and their solutions could be cast into transparent, thin, flexible films having good tensile properties and high thermal stability. The 10% weight loss temperatures were all above 495°C in air or nitrogen atmosphere, and the glass transition temperatures were in the range of 237°–276°C. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 823–831, 1999     

Preparation and properties of poly(amideether-imide)s derived from 1,4-bis(4-aminophenoxy)benzene,trimellitic anhydride,and various aromatic diamines

An imide ring containing dicarboxylic acid, 1,4-bis(4-trimellitimidophenoxy)benzene (III), was prepared by the condensation of 1,4-bis(4-aminophenoxy)benzene and trimellitic anhydride. A series of new poly(amide-ether-imide)s were prepared by the direct polycondensation of diimide-diacid III with various aromatic diamines using triphenyl phosphite and pyridine as condensing agents inN-methyl-2-pyrrolidone (NMP) in the presence of calcium chloride. The highest inherent viscosity value of a poly(amide-ether-imide) obtained was 1.78 dL/g (inN,N-dimethylacetamide, DMAc, at 30 °C). Flexible films with excellent tensile properties were cast from DMAc solutions. Glass transition temperatures of these poly(amide-ether-imide)s were recorded in the range of 248–297 C. These polymers do not show obvious weight loss before 400°C; the decomposition temperatures at which 10% weight loss in nitrogen and in air were observed for these poly(amide-ether-imide)s in the range of 521–564°C and 501–539°C, respectively. The polymers derived fromp-phenylenediamine or the diamines containing 1,4-bisphenoxy units exhibited a higher degree of crystallinity and higher initial decomposition temperatures but poor solubility in organic solvents.     

Preparation and properties of polyamide-imides derived from 1,3-bis(4-aminophenoxy)benzene,trimellitic anhydride,and various aromatic diamines

A diamine, 1,3-bis(4-aminophenoxy) benzene (II), was synthesized in two steps; fist from the condensation of resorcinol with p-chloronitrobenzene in the presence of potassium carbonate, producing I ,3-bis(4-nitrophenoxy) benzene (I), followed by hydrazine hydrate/Pd-C reduction. A two imide rings-preformed dicarboxylic acid, 1,3-bis(4-trimellitimidophenoxy)benzene (III), was prepared from the condensation of diamine II and trimellitic anhydride in 1:2 molar ratio. A series of structurally new polyamide-imides (V_a-p) were directly synthesized from the diacid III and various aromatic diamines (IV_a-p). The resultant polyamide-imides had inherent viscosities between 0.56–1.39 dl/g. All polymers, except some derived from diamines with p-phenoxy structure, showed excellent solubility. Some polymer resulted in tough or flexible transparent films. Dynamic TG data indicated that all polymers possess excellent thermal stability with no significant weight loss up to the temperature of approximately 450 °C in nitrogen, and their 10% weight loss temperature was recorded in the range of 489–577 °C. Measurements of wide-angle X-ray diffraction revealed that some polymers derived from p-phenoxy group-containing diamines showed crystalline patterns.     

Synthesis of new poly(amide-imide)s XX. Preparation and properties of poly(amide-Imide)s derived from 1,7-Bis(4-aminophenoxy) naphthalene,trimellitic anhydride,and various aromatic diamines

A dicarboxylic acid (1,7-BTMPN) bearing two preformed imide rings, was prepared from the condensation of 1,7-bis(4-aminophenoxy)naphthalene and trimellitic anhydride. A new family of poly(amide-imide)s with inherent viscosities up to 1.56 dL/g (0.5g/dL in DMAc at 30 °C) was prepared by the triphenyl phosphite activated polycondensation from the diimide-diacid 1,7-BTMPN with various aromatic diamines in a medium consisting ofN-methyl-2-pyrrolidone (NMP), pyridine, and calcium chloride. Most of the resulting polymers were readily soluble in polar solvents such as NMP and DMAc. All the soluble poly(amide-imide)s can form transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 185–267°C and the 10% weight loss temperatures were above 430 °C in nitrogen.     

Syntheses and properties of new poly(amide–imide)s based on 1,4‐bis(4‐aminophenoxy)naphthalene and various diimide–diacids

A series of new alternative poly(amide–imide)s (PAIs, III_a–j ) was synthesized by the direct polycondensation of 1,4‐bis(4‐aminophenoxy)naphthalene (1,4‐BAPON) with various aromatic diimide–diacids. These polymers were obtained in quantitative yields with inherent viscosities of 0.71–1.03 dL/g. Except for III_a, most of the polymers were soluble in aprotic polar solvents such as NMP, DMAc, DMF, and DMSO and could be solution‐cast into transparent, flexible, and tough films. The glass transition temperatures of these PAIs were in the range of 235–280°C. Thermogravimetric analyses established that these polymers were fairly stable up to 450°C, and 10% weight loss temperatures were recorded in the range of 520–569°C under nitrogen and 506–566°C under an air atmosphere. Compared with the PAIs with the 1,4‐bis(4‐aminophenoxy)benzene structure (series IV), the solubility of series III was better than that of series IV. Series III also exhibited lower crystallinity and better processability than those of series IV. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 217–225, 2000     

Preparation of new poly(amide–imide)s with chiral architectures via direct polyamidation reaction

N‐trimellitylimido‐L ‐methionine ( 3 ) was prepared by reaction of trimellitic anhydride ( 1 ) with ‐L ‐methionine ( 2 ) in acetic acid solution at refluxing temperature. This diacid was reacted with thionyl chloride, and N‐trimellitylimido‐L ‐methionine diacid chloride ( 4 ) was obtained in quantitative yield. The resulting diacid chloride was reacted with p‐aminobenzoic acid in dry acetone and bis(p‐aminobenzoic acid)‐N‐trimellitylimido‐L ‐methionine ( 5 ) was obtained as a novel optically active amide–imide diacid monomer in high yield. The direct polycondensation of amide–imide diacid monomer 5 with several aromatic diamines was carried out with tosyl chloride (TsCl)/pyridine (Py)/dimetheylformamide (DMF) system. The resulting thermally stable poly(amide–imide)s (PAIs) were obtained in good yields and inherent viscosities ranging between 0.24 and 0.46 dL g^?1 and were characterized with FTIR, ¹H NMR, CHN, and TGA techniques. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1248–1254, 2007     

Synthesis and characterization of new aromatic poly(amide–imide)s based on 4‐aryl‐2,6‐bis(4‐trimellitimidophenyl) pyridines

New diimide–dicarboxylic acids, ie 4‐phenyl‐2,6‐bis(4‐trimellitimidophenyl)pyridine and 4‐p‐biphenyl‐2,6‐bis‐(4‐trimellitimidophenyl)pyridine, were synthesized by the condensation reaction of 4‐phenyl‐2,6‐bis(4‐aminophenyl)pyridine and 4‐p‐biphenyl‐2,6‐bis(4‐aminophenyl)pyridine with trimellitic anhydride in glacial acetic acid or dimethylformamide. The monomers were fully characterized by FT‐IR and NMR spectroscopies, and elemental analyses. A series of novel poly(amide–imide)s with inherent viscosities of 0.68–0.87 dl g^?1 was prepared from the two diimide–diacids with various aromatic diamines by direct polycondensation. The poly(amide–imide)s were characterized by FT‐IR and NMR spectroscopies. The λ_max data for the resulting poly(amide–imide)s were in the range of 260–292 nm. These polymers exhibited good solubilities in polar aprotic solvents. The 10 % weight loss temperatures are above 485 °C under a nitrogen atmosphere. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of novel heat resistance poly(amide‐imide)s from N,N′‐[2,5‐bis(4‐aminobenzylidene) cyclopentanone] bistrimellitimide acid and various aromatic diamines

A new‐type of dicarboxylic acid was synthesized from the reaction of 2,5‐bis(4‐aminobenzylidene)cyclopentanone with trimellitic anhydride in a solution of glacial acetic acid/pyridine (Py) at refluxing temperature. Six novel heat resistance poly(amide‐imide)s (PAIs) with good inherent viscosities were synthesized, from the direct polycondensation reaction of N,N′‐[2,5‐bis(4‐aminobenzylidene)cyclopentanone]bistrimellitimide acid with several aromatic diamines, by two different methods such as direct polycondensation in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP)/triphenyl phosphite (TPP)/calcium chloride (CaCl₂)/pyridine (Py) and direct polycondensation in a p‐toluene sulfonyl chloride (tosyl chloride, TsCl)/pyridine (Py)/N,N‐dimethylformamide (DMF) system. All of the above polymers were fully characterized by ¹H NMR, FTIR, elemental analysis, inherent viscosity, solubility tests, UV‐vis spectroscopy, differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), and derivative of thermaogravimetric (DTG). The resulted poly(amide‐imide)s (PAIs) have showed admirable good inherent viscosities, thermal stability, and solubility. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of poly(amide–imide)s and their precursors as materials for membranes

Water soluble diamine amic acids (DAAs) were synthesized by reacting aliphatic diamines with pyromellitic dianhydride. Poly(amide–amic acid)s (PAAs) were prepared by interfacial polycondensation of DAAs in aqueous sodium hydroxide solution with isophthaloyl chloride in dichloromethane. Poly(amide–imide)s (PAIs) containing alternating (amide–amide)–(imide–imide) sequences were obtained by thermal cycloimidization of the PAA films at 175°C for 4 h in a forced air woven. The PAIs were readily soluble in polar aprotic solvents such as dimethylformamide, dimethylacetamide, dimethylsulfoxide, and N‐methyl‐2‐pyrrolidone. The inherent viscosities of the polymers are in the range of 0.97–1.7 dL/g. The polymers were characterized by IR, ¹H nuclear magnetic resonance (NMR), and thermogravimetric analysis (TGA). Thin film composite membranes containing PAA ultrathin barrier layer were prepared by in situ interfacial polycondensation of DAA in water with trimesoyl chloride or isophthaloyl chloride in hexane on the surface of a porous polysulfone membrane. The membranes were characterized for water permeability and for the separation of NaCl and Na₂SO₄. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1721–1727, 2000     

Synthesis and properties of some novel,soluble and light‐coloured,aromatic poly(amide–imide) copolymers

A new type of tetraimide‐dicarboxylic acid (I) was synthesized starting from the ring‐opening addition of m‐aminobenzoic acid (m‐ABA), 4,4′‐oxydiphthalic anhydride (ODPA) and 4,4′‐methylenedianiline (MDA) at a 2:2:1 molar ratio in N‐methyl‐2‐pyrrolidone (NMP), followed by cyclodehydration to the diacid I. A series of soluble and light‐coloured poly(amide–imide–imide)s (III_a–j) was prepared by triphenyl phosphite‐activated polycondensation from the tetraimide‐diacid I with various aromatic diamines (II_a–j). All films cast from DMAc had cutoff wavelengths shorter than 400 nm (376–393 nm) and had b* values between 20.46 and 40.67; these polymers were much lighter in colour than those of the corresponding trimellitimide series. All polymers were readily soluble in a variety of organic solvents such as NMP, N,N‐dimethylacetamide, dimethyl sulfoxide, and even in the less polar m‐cresol and pyridine. Compared with those of corresponding ODPA–MDA polyimide, the solubilities of poly(amide–imide–imide)s III_a–j were greatly improved. Polymers III_a–j afforded tough, transparent, and flexible films, which had tensile strengths ranging from 82 to 105 MPa, elongations at break from 8 to 14%, and initial moduli from 2.0 to 2.2 GPa. The glass transition temperature of polymers were recorded at 255–288 °C. They had 10% weight loss at a temperature above 540 °C and left more than 60% residue even at 800 °C in nitrogen. © 2002 Society of Chemical Industry     

Synthesis and characterization of novel aromatic poly(amide‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl or 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic diamines

New aromatic diimide‐dicarboxylic acids having kinked and cranked structures, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b), were synthesized by the reaction of trimellitic anhydride with 2,2′‐bis(4‐aminophenoxy)biphenyl (1a) and 2,2′‐bis(4‐aminophenoxy)‐1,1′‐binaphthyl (1b), respectively. Compounds 2a and 2b were characterized by FT‐IR and NMR spectroscopy and elemental analyses. Then, a series of novel aromatic poly(amide‐imide)s were prepared by the phosphorylation polycondensation of the synthesized monomers with various aromatic diamines. Owing to structural similarity, and a comparison of the characterization data, a model compound was synthesized by the reaction of 2b with aniline. The resulting polymers with inherent viscosities of 0.58–0.97 dl g^?1 were obtained in high yield. The polymers were fully characterized by FT‐IR and NMR spectroscopy. The ultraviolet λ_max values of the poly(amide‐imide)s were also determined. The polymers were readily soluble in polar aprotic solvents. They exhibited excellent thermal stabilities and had 10% weight loss at temperatures above 500 °C under a nitrogen atmosphere. Copyright © 2003 Society of Chemical Industry     

Synthesis and properties of poly(amide–imide)s based on N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide,p‐aminobenzoic acid and various aromatic diamines

A new diimide–diacid monomer, N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide (I), was prepared by azeotropic condensation of 4,4′‐oxydiphthalic anhydride (ODPA) and p‐aminobenzoic acid (p‐ABA) at a 1:2 molar ratio in a polar solvent mixed with toluene. A series of poly(amide–imide)s (PAI, III_a–m) was synthesized from the diimide–diacid I (or I′, diacid chloride of I) and various aromatic diamines by direct polycondensation (or low temperature polycondensation) using triphenyl phosphite and pyridine as condensing agents. It was found that only III_k–m having a meta‐structure at two terminals of the diamine could afford good quality, creasable films by solution‐casting; other PAIs III using diamine with para‐linkage at terminals were insoluble and crystalline; though III_g–i contained the soluble group of the diamine moieties, their solvent‐cast films were brittle. In order to improve their to solubility and film quality, copoly(amide–imide)s (Co‐PAIs) based on I and mixtures of p‐ABA and aromatic diamines were synthesized. When on equimolar of p‐ABA (m = 1) was mixed, most of Co‐PAIs IV had improved solubility and high inherent viscosities in the range 0.9–1.5 dl g^?1; however, their films were still brittle. With m = 3, series V was obtained, and all members exhibited high toughness. The solubility, film‐forming ability, crystallinity, and thermal properties of the resultant poly(amide–imide)s were investigated. © 2002 Society of Chemical Industry     

Synthesis of new poly(amide–imide)s derived from trimellitylimido‐L‐phenylalanine

N‐Trimellitylimido‐L ‐phenylalanine was prepared from the reaction of 1,2,4‐benzenetricarboxylic anhydride with L ‐phenylalanine in N,N‐dimethylformamide solution at refluxing temperature. The direct polycondensation reaction of the monomer imide‐diacid with 4,4′‐diaminodiphenylsulfone, 4,4′‐diaminodiphenylmethane, 1,4‐phenylenediamine, 1,3‐phenylenediamine, 2,4‐diaminotoluene, 4,4′‐diaminodiphenylether and benzidine was carried out in a medium consisting of triphenyl phosphite, N‐methyl‐2‐pyrrolidone, pyridine and calcium chloride. The resulting poly(amide–imide)s, PAIs, having inherent viscosities of 0.21–0.45 dlg^?1 were obtained in high yield. All of the above compounds were fully characterized by IR spectroscopy and elemental analyses. The optical rotation of all PAIs has also been measured. Some structural characterization and physical properties of these new optically active PAIs are reported. © 2001 Society of Chemical Industry     

Microwave‐promoted rapid synthesis of new optically active poly(amide imide)s derived from N,N′‐(pyromellitoyl)‐bis‐L‐isoleucine diacid chloride and aromatic diamines

A pyromellitic dianhydride (benzene‐1,2,4,5‐tetracarboxylic dianhydride) was reacted with L ‐isoleucine in acetic acid, and the resulting imide acid [N,N′‐(pyromellitoyl)‐bis‐L ‐isoleucine] (4) was obtained in a high yield. 4 was converted into N,N′‐(pyromellitoyl)‐bis‐L ‐isoleucine diacid chloride by a reaction with thionyl chloride. The polycondensation reaction of this diacid chloride with several aromatic diamines, including 1,4‐phenylenediamine, 4,4′‐diaminodiphenyl methane, 4,4′‐diaminodiphenylsulfone (4,4′‐sulfonyldianiline), 4,4′‐diaminodiphenylether, 2,4‐diaminotoluene, and 1,3‐phenylenediamine, was developed with two methods. The first method was polymerization under microwave irradiation, and the second method was low‐temperature solution polymerization, with trimethylsilyl chloride used as an activating agent for the diamines. The polymerization reactions proceeded quickly and produced a series of optically active poly(amide imide)s with good yields and moderate inherent viscosities of 0.17–0.25 dL/g. All of the aforementioned polymers were fully characterized by IR, elemental analyses, and specific rotation. Some structural characterization and physical properties of these optically active poly(amide imide)s are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 951–959, 2004     

Novel organosoluble poly(amide‐imide‐imide)s synthesized from new tetraimide‐dicarboxylic acid by condensation with 4,4′‐oxydiphthalic anhydride, 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene,trimellitic anhydride,and various aromatic diamines

A new monomer of tetraimide‐dicarboxylic acid (IV) was synthesized by starting from ring‐opening addition of 4,4′‐oxydiphthalic anhydride, trimellitic anhydride, and 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene at a 1:2:2 molar ratio in N‐methyl‐2‐pyrrolidone (NMP). From this new monomer, a series of novel organosoluble poly(amide‐imide‐imide)s with inherent viscosities of 0.7–0.96 dL/g were prepared by triphenyl phosphite activated polycondensation from the tetraimide‐diacid with various aromatic diamines. All synthesized polymers were readily soluble in a variety of organic solvents such as NMP and N,N‐dimethylacetamide, and most of them were soluble even in less polar m‐cresol and pyridine. These polymers afforded tough, transparent, and flexible films with tensile strengths ranging from 99 to 125 MPa, elongations at break from 12 to 19%, and initial moduli from 1.6 to 2.4 GPa. The thermal properties and stability were also good with glass‐transition temperatures of 236–276°C and thermogravimetric analysis 10 wt % loss temperatures of 504–559°C in nitrogen and 499–544°C in air. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2854–2864, 2006     

Synthesis and properties of new poly(amide‐imide)s based on 1,3‐bis[4,4'‐(trimellitimido) phenoxy] propane and aromatic diamines

Six new poly(amide‐imide)s 8a–f containing trimethylene moiety in the main chain were synthesized by the polycondensation reactions of 1,3‐bis[4,4'‐(trimellitimido) phenoxy] propane 6 with six different aromatic diamines 7a–f in a medium constituting N‐methyl‐2‐pyrrolidone, triphenylphosphite, CaCl₂, and pyridine as condensing agents. The polycondensation reaction produced a series of novel poly(amide‐imide)s 8a–f in high yields with inherent viscosities between 0.35 and 0.63 dL/g. The resulting poly(amide‐imide)s were characterized by elemental analysis, viscosity measurements, thermal gravimetric analysis (TGA and DTG), solubility tests, and FTIR spectroscopy. 1,3‐Bis[4,4'‐(trimellitimido) phenoxy] propane 6 as a new monomer containing trimethylene moiety was synthesized using a three‐step reaction. At first 1,3‐bis[4,4'‐nitrophenoxy] propane 3 was prepared by the reaction of 4‐nitrophenol 1 with 1,3‐dibromo propane 2 in DMF solution . Then, dinitro 3 was reduced to 1,3‐bis[4,4'‐aminophenoxy] propane 4 by using a solution of sodium sulfite in ethanol. Finally, 1,3‐bis[4,4'‐(trimellitimido) phenoxy] propane 6 was prepared by the reaction of one equivalent diamine 4 with two equivalents of trimellitic anhydride 5 in a mixture of acetic acid‐pyridine (3 : 2). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of new rigid‐rod and organosoluble poly(amide–imide)s based on 1,4‐bis(trimellitimido)‐2,3,5,6‐tetramethylbenzene

A series of new aromatic poly(amide–imide)s (PAIs) was synthesized by triphenyl phosphite‐activated polycondensation of the diimide–diacid, 1,4‐bis(trimellitimido)‐2,3,5,6‐tetramethylbenzene (I), with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP), pyridine, and calcium chloride. The PAIs had inherent viscosities of 0.82–2.43 dL/g. The diimide–diacid monomer (I) was prepared from 2,3,5,6‐tetramethyl‐p‐phenylenediamine with trimellitic anhydride (TMA). Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents including NMP, N,N‐dimethylacetamide (DMAc), and N,N‐dimethylformamide (DMF). Transparent, flexible, and tough films of these polymers could be cast from DMAc solutions. Their cast films had tensile strengths ranging from 80 to 95 MPa, elongation at break from 10 to 45%, and initial modulus from 2.01 to 2.50 GPa. The 10% weight loss temperatures of these polymers were above 510°C in nitrogen. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1162–1170, 2000     

Synthesis and characterization of new cardo poly(ether imide)s derived from 9,9‐bis [4‐(4‐aminophenoxy)phenyl]xanthene

A series of new cardo poly(ether imide)s bearing flexible ether and bulky xanthene pendant groups was prepared from 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene with six commercially available aromatic tetracarboxylic dianhydrides in N,N‐dimethylacetamide (DMAc) via the poly(amic acid) precursors and subsequent thermal or chemical imidization. The intermediate poly(amic acid)s had inherent viscosities between 0.83 and 1.28 dL/g, could be cast from DMAc solutions and thermally converted into transparent, flexible, and tough poly(ether imide) films which were further characterized by X‐ray and mechanical analysis. All of the poly(ether imide)s were amorphous and their films exhibited tensile strengths of 89–108 MPa, elongations at break of 7–9%, and initial moduli of 2.12–2.65 GPa. Three poly(ether imide)s derived from 4,4′‐oxydiphthalic anhydride, 4,4′‐sulfonyldiphthalic anhydride, and 2,2‐bis(3,4‐dicarboxyphenyl))hexafluoropropane anhydride, respectively, exhibited excellent solubility in various solvents such as DMAc, N,N‐dimethylformamide, N‐methyl‐2‐pyrrolidinone, pyridine, and even in tetrahydrofuran at room temperature. The resulting poly(ether imide)s with glass transition temperatures between 286 and 335°C had initial decomposition temperatures above 500°C, 10% weight loss temperatures ranging from 551 to 575°C in nitrogen and 547 to 570°C in air, and char yields of 53–64% at 800°C in nitrogen. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of novel diimide–dinaphthols and resulting poly(urethane–imide)s

Novel diols containing imide groups were prepared via condensation of aromatic dianhydrides with 5‐amino‐1‐naphthol. The diimide–dinaphthols prepared were characterized by conventional methods and used to synthesize new poly(urethane–imide)s (PUIs). All the polymers were characterized and their physical properties, such as solubility, solution viscosity, thermal stability, and thermal behaviour were studied. The polymers obtained showed more thermal stability than typical polyurethanes because of the presence of the imide groups. Copyright © 2003 Society of Chemical Industry     

Synthesis and characterization of novel optically active poly(amide–imide)s containing N,N′‐(pyromellitoyl)‐bis‐L‐valine diacid chloride and 5,5‐disubstituted hydantoin derivatives under microwave irradiation

Pyromellitic dianhydride (1,2,4,5‐benzenetetracarboxylic acid 1,2,4,5‐dianhydide) was reacted with L ‐valine in a mixture of acetic acid and pyridine (3:2) at room temperature, and then was refluxed at 90–100 °C, N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid was obtained in quantitative yield. The imide–acid was converted to N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid chloride by reaction with thionyl chloride. Rapid and highly efficient synthesis of a number of poly(amide–imide)s was achieved under microwave irradiation using a domestic microwave oven by polycondensation of N,N′‐(pyromellitoyl)‐bis‐L ‐valine diacid chloride with six different derivatives of 5,5‐disubstituted hydantoin compounds in the presence of a small amount of a polar organic medium that acts as a primary microwave absorber. A suitable organic medium was o‐cresol. The polycondensation proceeded rapidly, compared with conventional melt polycondensation and solution polycondensation and was almost completed within 8 min, giving a series of poly(amide–imide)s with inherent viscosities in the range 0.15–0.36 dl g^?1. The resulting poly(amide–imide)s were obtained in high yield and are optically active and thermally stable. All of the above compounds were fully characterized by Fourier‐transform infrared (FT‐IR) spectroscopy, elemental analysis, inherent viscosity (η_inh) measurements, solubility testing and specific rotation measurements. The thermal properties of the poly(amide–imide)s were investigated by using thermogravimetric analysis. Copyright © 2004 Society of Chemical Industry