Catalytic oxidation of methane over hexaaluminates and hexaaluminate-supported Pd catalysts

An aqueous (NH₄)₂CO₃ coprecipitation method, based on that of Groppi et al. [Appl. Catal. A 104 (1993) 101–108] was used to synthesize Sr_1−xLa_xMnAl₁₁O₁₉₋ hexaaluminates. These materials were first synthesized by alkoxide hydrolysis. This synthesis route requires special handling of the starting materials and is not likely to be commercially practical. The materials prepared by (NH₄)₂CO₃ coprecipitation have similar surface areas as those prepared by the alkoxide hydrolysis method. Their CH₄ oxidation activity, measured as the temperature needed for 10% conversion of methane, is higher than those prepared by alkoxide hydrolysis. The La-substantiated material, LaMnAl₁₁O₁₉₋, shows high surface area with 19.3 m²/g after calcination at 1400°C for 2 h. It is active for CH₄ oxidation with T_10% at 450°C using 1% CH₄ in air and 70 000 cm³/h g space velocity. The stability and activity of LaMnAl₁₁O₁₉₋ prepared by (NH₄)₂CO₃ coprecipitation method is a simple and important step forward for the application of CH₄ catalytic combustion for gas turbines.     

Catalytic reduction of NO by propene over LaCo1−xCuxO3 perovskites synthesized by reactive grinding

One series of LaCo_1−xCu_xO₃ perovskites with high specific surface area was prepared by the new method designated as reactive grinding. These solids were characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), H₂-temperature programmed reduction (TPR), O₂-temperature programmed desorption (TPD), NO + O₂-TPD, C₃H₆-TPD, NO + O₂-temperature programmed surface reaction (TPSR) under C₃H₆/He flow as well as catalytic reduction of NO activity tests. The catalytic performance of unsubstituted sample is poor with a maximum conversion to N₂ of 19% at 500 °C at a space velocity of 55,000 h⁻¹ (3000 ppm NO, 3000 ppm C₃H₆, 1% O₂ in helium) but it is improved by incorporation of Cu into the lattice. A maximal N₂ yield of 46% was observed over LaCo_0.8Cu_0.2O₃ under the same conditions. Not only the abundance of -oxygen but also the mobility of β-oxygen of lanthanum cobaltite was remarkably enhanced by Cu substitution according to O₂-TPD and H₂-TPR studies. The better performance of Cu-substituted samples is likely to correspond to the essential nature of Cu and facility to form nitrate species in NO transformation conditions. In the absence of O₂, the reduction of NO by C₃H₆ was performed over LaCo_0.8Cu_0.2O₃, leading to a maximal conversion to N₂ of 73% accompanied with the appearance of some organo nitrogen compounds (identified as mainly C₃H₇NO₂). Subsequently, a mechanism involving the formation of an organic nitro intermediate, which further converts into N₂, CO₂ and H₂O via isocyanate, was proposed. Gaseous oxygen acts rather as an inhibitor in the reaction of NO and C₃H₆ over highly oxidative LaCo_0.8Cu_0.2O₃ due to the heavily unselective combustion of C₃H₆ by O₂.     

Water vapor sensitivity of nanosized La(Co, Mn, Fe)1−x(Cu, Pd)xO3 perovskites during NO reduction by C3H6 in the presence of oxygen

A series of La(Co, Mn, Fe)_1−x(Cu, Pd)_xO₃ perovskites having high specific surface areas and nanosized crystal domains was prepared by reactive grinding. The solids were characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed desorption (TPD) of O₂, NO + O₂, C₃H₆, in the absence or presence of 5% H₂O, Fourier transform infrared (FTIR) spectroscopy, as well as activity tests towards NO reduction by propene under the conditions of 3000 ppm NO, 3000 ppm C₃H₆, 1% O₂, 0 or 10% H₂O, and 50,000 h⁻¹ space velocity. The objective was to investigate the influence of H₂O addition on catalytic behavior. A good performance (100% NO conversion, 77% N₂ yield, and 90% C₃H₆ conversion) was achieved at 600 °C over LaFe_0.8Cu_0.2O₃ under a dry feed stream. With the exposure of LaFe_0.8Cu_0.2O₃ to a humid atmosphere containing 10% water vapor, the catalytic activity was slightly decreased yielding 91% NO conversion, 51% N₂ yield, and 86% C₃H₆ conversion. A competitive adsorption between H₂O vapor with O₂ and NO molecules at anion vacancies over LaFe_0.8Cu_0.2O₃ was found by means of TPD studies here. A deactivation mechanism was therefore proposed involving the occupation of available active sites by water vapor, resulting in an inhibition of catalytic activity in C₃H₆ + NO + O₂ reaction. This H₂O deactivation was also verified to be strictly reversible by removing steam from the feed.     

Catalytic combustion of soot over alkali doped SrTiO3

The effect of introduction of alkalies (Me = Li, K, Cs) into SrTiO₃ on the physico-chemical properties of resulted materials and their catalytic activity in soot combustion was studied. Two groups of SrTiO₃ based perovskites were prepared: substituted in A-position of the structure (Sr_1 − xMe_xTiO₃, x = 0.05–0.2) and impregnated with the same amount of alkali metals. Prepared materials exhibit low specific surface area and perovskite structure, only these ones impregnated with the highest amount of Cs (K) show weak XRD signals of Me₂O. TPD-O₂ experiments show bimodal profiles of O₂ desorption curves with maximums corresponding to individual step of alkali nitrates thermal decomposition. It is supposed that second peak of O₂ desorption from impregnated SrTiO₃ can be related to reversible decomposition of MeNO₃. XPS shows that surface of SrTiO₃ substituted with K (Cs) is much richer in these elements than the surface of impregnated one. Prepared materials lower the temperature of soot ignition from 530 (inert) to 470 °C for SrTiO₃ and to 302–303 °C for Sr_0.8K_0.2TiO₃ and Sr_0.8K_0.2TiO₃, respectively. Substituted materials are more active in soot combustion than impregnated ones. A mechanism explaining effect of alkali metals nitrate addition to SrTiO₃ on its catalytic activity in soot combustion is proposed.     

Preparation of CexZr1−xO2 (x = 0.75, 0.62) solid solution and its application in Pd-only three-way catalysts

Nanoparticles of Ce_xZr_1−xO₂ (x = 0.75, 0.62) were prepared by the oxidation-coprecipitation method using H₂O₂ as an oxidant, and characterized by N₂ adsorption, XRD and H₂-TPR. Ce_xZr_1−xO₂ prepared had single fluorite cubic structure, good thermal stability and reduction property. With the increasing of Ce/Zr ratio, the surface area of Ce_xZr_1−xO₂ increased, but thermal stability of Ce_xZr_1−xO₂ decreased. The surface area of Ce_0.62Zr_0.38O₂ was 41.2 m²/g after calcination in air at 900 °C for 6 h. TPR results showed the formation of solid solution promoted the reduction of CeO₂, and the reduction properties of Ce_xZr_1−xO₂ were enhanced by the cycle of TPR-reoxidation. The Pd-only three-way catalysts (TWC) were prepared by the impregnation method, in which Ce_0.75Zr_0.25O₂ was used as the active washcoat and Pd loading was 0.7 g/L. In the test of Air/Fuel, the conversion of C₃H₈ was close to 100% and NO was completely converted at λ < 1.025. The high conversion of C₃H₈ was induced by the steam reform and dissociation adsorption reaction of C₃H₈. Pd-only catalyst using Ce_0.75Zr_0.25O₂ as active washcoat showed high light off activity, the reaction temperatures (T₅₀) of 50% conversion of CO, C₃H₈ and NO were 180, 200 and 205 °C, respectively. However, the conversions of C₃H₈ and NO showed oscillation with continuously increasing the reaction temperature. The presence of La₂O₃ in washcoat decreased the light off activity and suppressed the oscillation of C₃H₈ and NO conversion. After being aged at 900 °C for 4 h, the operation windows of catalysts shifted slightly to rich burn. The presence of La₂O₃ in active washcoat can enhance the thermal stability of catalyst significantly.     

CO2, NOx and SO2 emissions from the combustion of coal with high oxygen concentration gases

The emissions of CO₂, NO_x and SO₂ from the combustion of a high-volatile coal with N₂- and CO₂-based, high O₂ concentration (20, 50, 80, 100%) inlet gases were investigated in an electrically heated up-flow-tube furnace at elevated gas temperatures (1123–1573 K). The fuel equivalence ratio, φ, was varied in the range of 0.4–1.6. Results showed that CO₂ concentrations in flue gas were higher than 95% for the processes with O₂ and CO₂-based inlet gases. NO_x emissions increased with φ under fuel-lean conditions, then declined dramatically after φ=0.8, and the peak values increased from about 1000 ppm for the air combustion process and 500 ppm for the O₂(20%)+CO₂(80%) inlet gas process to about 4500 ppm for the oxygen combustion process. When φ>1.4 the emissions decreased to the same level for different O₂ concentration inlet gas processes. On the other hand, NO_x emission indexes decreased monotonically with φ under both fuel-lean and fuel-rich combustion. SO₂ emissions increased with φ under fuel-lean conditions, then declined slightly after φ>1.2. Temperature has a large effect on the NO_x emission. Peak values of the NO_x emission increased by 50–70% for the N₂-based inlet gas processes and by 30–50% for the CO₂-based inlet gas process from 1123 to 1573 K. However, there was only a small effect of temperature on the SO₂ emission.     

The reduction phase in NOx storage catalysis: Effect of type of precious metal and reducing agent

The effect of different reducing agents (H₂, CO, C₃H₆ and C₃H₈) on the reduction of stored NO_x over PM/BaO/Al₂O₃ catalysts (PM = Pt, Pd or Rh) at 350, 250 and 150 °C was studied by the use of both NO₂-TPD and transient reactor experiments. With the aim of comparing the different reducing agents and precious metals, constant molar reduction capacity was used during the reduction period for samples with the same molar amount of precious metal. The results reveal that H₂ and CO have a relatively high NO_x reduction efficiency compared to C₃H₆ and especially C₃H₈ that does not show any NO_x reduction ability except at 350 °C over Pd/BaO/Al₂O₃. The type of precious metals affects the NO_x storage-reduction properties, where the Pd/BaO/Al₂O₃ catalyst shows both a high storage and a high reduction ability. The Rh/BaO/Al₂O₃ catalyst shows a high reduction ability but a relatively low NO_x storage capacity.     

Potassium–copper and potassium–cobalt catalysts supported on alumina for simultaneous NOx and soot removal from simulated diesel engine exhaust

This paper deals with the activity of bimetallic potassium–copper and potassium–cobalt catalysts supported on alumina for the reduction of NO_x with soot from simulated diesel engine exhaust. The effect of the reaction temperature, the soot/catalyst mass ratio and the presence of C₃H₆ has been studied. In addition, the behavior of two monometallic catalysts supported on zeolite beta (Co/beta and Cu/beta), previously used for NO_x reduction with C₃H₆, as well as a highly active HC-SCR catalyst (Pt/beta) has been tested for comparison. The preliminary results obtained in the absence of C₃H₆ indicate that, at temperatures between 250 and 400 °C, the use of bimetallic potassium catalysts notably increases the rate of NO_x reduction with soot evolving N₂ and CO₂ as main reaction products. At higher temperatures, the catalysts mainly favor the direct soot combustion with oxygen. In the presence of C₃H₆, an increase in the activity for NO_x reduction has been observed for the catalyst with the highest metal content. At 450 °C, the copper-based catalysts (Cu/beta and KCu2/Al₂O₃) show the highest activity for both NO_x reduction (to N₂ and CO₂) and soot consumption. The Pt/beta catalyst does not combine, at any temperature, a high NO_x reduction with a high soot consumption rate.     

The low-temperature performance of NOx storage and reduction catalyst

The catalytic performance and the behavior of NO_x storage and reduction (NSR) over a model catalyst for lean-burn gasoline engines have been mainly investigated and be discussed based on the temperature and reducing agents use in this study. The experimental results have shown that the NO_x storage amount in the lean atmosphere was the same as the NO_x reduction amount from the subsequent rich spike (RS) above the temperature of 400 °C, while the former was greater than the latter below the temperature of 400 °C. This indicated that when the temperature was below 400 °C compared with the NO_x storage stage, the reduction of the stored NO_x is somehow restricted. We found that the reduction efficiencies with the reducing agents decrease in the order H₂ > CO > C₃H₆ below 400 °C, thus not all of the NO_x storage sites could be fully regenerated even using an excessive reducing agent of CO or C₃H₆, which was supplied to the NSR catalyst, while all the NO_x storage sites could be fully regenerated if an adequate amount of H₂ was supplied. We also verified that the H₂ generation more favorably occurred through the water gas shift reaction than through the steam reforming reaction. This difference in the H₂ generation could reasonably explain why CO was more efficient for the reduction of the stored NO_x than C₃H₆, and hinted as a promising approach to enhance the low-temperature performance of the current NSR catalysts though promoting the H₂ generation reaction.     

The selective reduction of NOx with propene on Pt-beta catalyst: A transient study

The mechanism of the NO/C₃H₆/O₂ reaction has been studied on a Pt-beta catalyst using transient analysis techniques. This work has been designed to provide answers to the volcano-type activity behaviour of the catalytic system, for that reason, steady state transient switch (C₃H₆/NO/O₂ → C₃H₆/Ar/O₂, C₃H₆/Ar/O₂ → C₃H₆/NO/O₂, C₃H₆/NO/O₂ → Ar/NO/O₂, Ar/NO/O₂ → C₃H₆/NO/O₂, C₃H₆/NO/O₂ → C₃H₆/NO/Ar and C₃H₆/NO/Ar → C₃H₆/NO/O₂) and thermal programmed desorption (TPD) experiments were conducted below and above the temperature of the maximum activity (T_max). Below T_max, at 200 °C, a high proportion of adsorbed hydrocarbon exists on the catalyst surface. There exists a direct competition between NO and O₂ for Pt free sites which is very much in favour of NO, and therefore, NO reduction selectively takes place over hydrocarbon combustion. NO and C₃H₆ are involved in the generation of partially oxidised hydrocarbon species. O₂ is essential for the oxidation of these intermediates closing the catalytic cycle. NO₂ is not observed in the gas phase. Above T_max, at 230 °C, C₃H_6 ads coverage is negligible and the surface is mainly covered by O_ads produced by the dissociative adsorption of O₂. NO₂ is observed in gas phase and carbon deposits are formed at the catalyst surface. From these results, the state of Pt-beta catalyst at T_max is inferred. The reaction proceeds through the formation of partially oxidised active intermediates (C_xH_yO_zN_w) from C₃H_6 ads and NO_ads. The combustion of the intermediates with O₂(g) frees the Pt active sites so the reaction can continue. Temperature has a positive effect on the surface reaction producing active intermediates. On the contrary, formation of NO_ads and C₃H_6 ads are not favoured by an increase in temperature. Temperature has also a positive effect on the dissociation of O₂ to form O_ads, consequently, the formation of NO₂ is favoured by temperature through the oxygen dissociation. NO₂ is very reactive and produces the propene combustion without NO reduction. These facts will determine the maximum concentration of active intermediates and consequently the maximum of activity.     

Comparative study of Pt-based catalysts on different supports in the low-temperature de-NOx-SCR with propene

Pt-based catalysts have been prepared using supports of different nature (γ-Al₂O₃, ZSM-5, USY, and activated carbon (ROXN)) for the C₃H₆-SCR of NO_x in the presence of excess oxygen. Nitrogen adsorption at 77 K, pH measurements, temperature-programmed desorption of propene, and H₂ chemisorption were used for the characterization of the different supports and catalysts. The performance of these catalysts has been compared in terms of de-NO_x activity, hydrocarbon adsorption and combustion at low temperature, and selectivity to N₂. Maximum NO_x conversions for all the catalysts were achieved in the temperature range of 200–250°C. The order of activity was, Pt-USY>Pt/ROXNPt-ZSM-5Pt/Al₂O₃. At temperatures above 300°C only Pt/ROXN maintains a high activity caused by the consumption of the support, while the other catalysts present a strong deactivation. Propene combustion starts at the same temperature for all the catalytic systems (160°C). Complete hydrocarbon combustion is directly related to the acidity of the support, thus determining the temperature of the maximum NO_x reduction. The support play an important role in the reaction mechanism through the hydrocarbon activation. N₂O formation was observed for all the catalysts. N₂ selectivity ranges from 15 to 30% with the order, Pt/ROXN>Pt-USYPt/Al₂O₃>Pt-ZSM-5. The catalytic systems exhibit a stable operation under isothermal conditions during time-on-stream experiments.     

SCR of NOx with CH3OH on H-mordenite: mechanism and reaction intermediates

The selective reduction of NO_x over H-mordenite (H-m) was studied using CH₃OH as reducing agent. Results are compared with those obtained with other conventional reducing agents (ethylene and methane), with gas-phase reactions, and with other metal-exchanged mordenites (Cu-mordenite (Cu-m) and Co-mordenite (Co-m)). H-m was found to be an effective catalyst for the SCR of NO_x with CH₃OH. When different reducing agents were compared over H-m, CH₃OH > C₂H₄ > CH₄ was the order according to the maximum NO conversion obtained using 1% of oxygen in the feed. Instead, if selectivity is considered, the order results CH₄ > CH₃OH > C₂H₄. In reaction experiments, two distinct zones defined by two maxima with NO to N₂ conversion are obtained at two different temperatures. A correlation exists between the said zones and the CO : CO₂ ratio. At low temperatures, CO prevails whereas at high temperatures CO₂ prevails. These results indicate that there exist different reaction intermediates. Evidence from reaction experiments, FTIR results, and transient experiments suggest that the reaction mechanism involves formaldehyde and dimethyl ether (DME) as intermediates in the 200–500°C temperature range. The surface interaction between CH₃OH (or its decomposition products) and NO is negligible if compared with NO₂, indicating that the oxidation of NO to NO₂ on acid sites is a fundamental path in this system. Different from other non-oxygenated reductants (methane and ethylene), a gas-phase NO_x initiation effect on hydrocarbon combustion was not observed.     

Effect of hydrogen on reaction intermediates in the selective catalytic reduction of NOx by C3H6

Selective catalytic reduction of NO_x by C₃H₆ in the presence of H₂ over Ag/Al₂O₃ was investigated using in situ DRIFTS and GC–MS measurements. The addition of H₂ promoted the partial oxidation of C₃H₆ to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO_x on Ag/Al₂O₃ surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H₂ on the SCR of NO_x by C₃H₆ over Ag/Al₂O₃ catalyst.     

The catalytic activity of FeOx/ZrO2 for the abatement of NO with propene in the presence of O2

FeO_x/ZrO₂ samples, prepared by impregnation with Fe(NO₃)₃, were characterised by means of DRS, XRD, FTIR, redox cycles and volumetric CO adsorption. Volumetric CO adsorption, combined with FTIR, showed that 45% of iron in the sample containing 2.8 Fe atoms nm⁻² was capable of forming iron carbonyls. DRS evidenced Fe₂O₃ on samples with Fe-content≥2.8 atoms nm⁻². The selective catalytic reduction of NO with C₃H₆ in the presence of O₂ was studied with a reactant mixture containing NO=4000 ppm, C₃H₆=4000 ppm, O₂=2%. The dependence on iron-content suggests that only isolated iron, prevailing in dilute FeO_x/ZrO₂, is active for NO reduction, whereas iron on the surface of small oxide particles, prevailing in concentrated FeO_x/ZrO₂, is active for C₃H₆ combustion.     

Studies on the deactivation of NOx storage-reduction catalysts by sulfur dioxide

The interaction of sulfur dioxide with a commercial NO_x storage-reduction catalyst (NSR) has been investigated using in situ IR and X-ray absorption spectroscopy. Two pathways of catalyst deactivation by SO₂ were identified. Under lean conditions (exposure to SO₂ and O₂) at 350 °C the storage component forms barium sulfates, which transform from surface to hardly reducible bulk sulfate species. The irreversible blocking of the Ba sites led to a decrease in NO_x storage capacity. Under fuel rich conditions (SO₂/C₃H₆) at 350–500 °C evidence for the formation of sulfides on the oxidation/reduction component (Pt) of the catalyst was found, which blocks the metal surface and thus hinders the further reduction of the sulfides.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

CO, H2 or C3H8 assisted catalytic combustion of methane over supported LaMnO3 monoliths

The effect of the addition of a second fuel such as CO, C₃H₈ or H₂ on the catalytic combustion of methane was investigated over ceramic monoliths coated with LaMnO₃/La-γAl₂O₃ catalyst. Results of autothermal ignition of different binary fuel mixtures characterised by the same overall heating value show that the presence of a more reactive compound reduces the minimum pre-heating temperature necessary to burn methane. The effect is more pronounced for the addition of CO and very similar for C₃H₈ and H₂. Order of reactivity of the different fuels established in isothermal activity measurements was: CO>H₂≥C₃H₈>CH₄. Under autothermal conditions, nearly complete methane conversion is obtained with catalyst temperatures around 800 °C mainly through heterogeneous reactions, with about 60–70 ppm of unburned CH₄ when pure methane or CO/CH₄ mixtures are used. For H₂/CH₄ and C₃H₈/CH₄ mixtures, emissions of unburned methane are lower, probably due to the proceeding of CH₄ homogeneous oxidation promoted by H and OH radicals generated by propane and hydrogen pyrolysis at such relatively high temperatures.

Finally, a steady state multiplicity is found by decreasing the pre-heating temperature from the ignited state. This occurrence can be successfully employed to pilot the catalytic ignition of methane at temperatures close to compressor discharge or easily achieved in regenerative burners.     

Catalytic oxidation of HCN over a 0.5% Pt/Al2O3 catalyst

The adsorption of HCN on, its catalytic oxidation with 6% O₂ over 0.5% Pt/Al₂O₃, and the subsequent oxidation of strongly bound chemisorbed species upon heating were investigated. The observed N-containing products were N₂O, NO and NO₂, and some residual adsorbed N-containing species were oxidized to NO and NO₂ during subsequent temperature programmed oxidation. Because N-atom balance could not be obtained after accounting for the quantities of each of these product species, we propose that N₂ and was formed. Both the HCN conversion and the selectivity towards different N-containing products depend strongly on the reaction temperature and the composition of the reactant gas mixture. In particular, total HCN conversion reaches 95% above 250 °C. Furthermore, the temperature of maximum HCN conversion to N₂O is located between 200 and 250 °C, while raising the reaction temperature increases the proportion of NO_x in the products. The co-feeding of H₂O and C₃H₆ had little, if any effect on the total HCN conversion, but C₃H₆ addition did increase the conversion to NO and decrease the conversion to NO₂, perhaps due to the competing presence of adsorbed fragments of reductive C₃H₆. Evidence is also presented that introduction of NO and NO₂ into the reactant gas mixture resulted in additional reaction pathways between these NO_x species and HCN that provide for lean-NO_x reduction coincident with HCN oxidation.     

In situ IR and pulse reaction studies on the active oxygen species over SrF2/Nd2O3 catalyst for oxidative coupling of methane

Pulse reaction method and in situ IR spectroscopy were used to characterize the active oxygen species for oxidative coupling of methane (OCM) over SrF₂/Nd₂O₃ catalyst. It was found that OCM activity of the catalyst was very low in the absence of gas phase oxygen, which indicated that lattice oxygen species contributed little to the yield of C₂ hydrocarbons. IR band of superoxide species (O₂⁻) was detected on the O₂-preadsorbed SrF₂/Nd₂O₃. The substitution of ¹⁸O₂ isotope for ¹⁶O₂ caused the IR band of O₂⁻ at 1128 cm⁻¹ to shift to lower wavenumbers (1094 and 1062 cm⁻¹), consistent with the assignment of the spectra to the O₂⁻ species. A good correlation between the rate of disappearance of surface O₂⁻ and the rate of formation of gas phase C₂H₄ was observed upon interaction of CH₄ with O₂-preadsorbed catalyst at 700 °C. The O₂⁻ species was also observed on the catalyst under working condition. These results suggest that O₂⁻ species is the active oxygen species for OCM reaction on SrF₂/Nd₂O₃ catalyst.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.