基于频率识别纤维增强复合材料弧形板分层损伤

利用损伤发生前后的频率变化识别纤维增强复合材料(FRP)弧形层合板中的分层损伤。首先建立含分层损伤的FRP弧形板有限元模型,在不同分层损伤情况下计算弧形板的频率,与无损伤弧形板比较后得到频率改变量。分别使用遗传算法、有代理模型的遗传算法和人工神经网络等三种逆向检测算法对分层的界面、位置和大小进行识别,发现遗传算法比人工神经网络的预测精度要高很多,而有代理模型的遗传算法由于采用近似模型替代遗传算法中的有限元模型,大大提高了算法的运算效率,在保证精度的前提下,损伤识别的时间是直接遗传算法的1/163。     

基体损伤对分层复合材料加筋板动力特性的影响研究

基于Mindlin假定的复合材料层合板单元和层合梁单元,推导了复合材料加筋板的刚度阵和质量阵;采用Adams应变能法与Rayleigh阻尼模型相结合的方法,构造了相应的阻尼阵列式;建立了分层损伤特征的三板模型和表征基体微裂纹损伤的基体损伤模型;并推导了一种基于Hertz型非线性接触法则的虚拟联接单元模型,以避免在振动分析过程中在低阶模态中分层处出现的上、下子板间不合理的嵌入现象;在上述模型和理论基础上,采用精细积分法求解含损伤结构的动力响应。对典型数例进行参数讨论,表明在动载荷作用下,嵌入分层损伤以及在振动过程中诱发的基体微裂纹损伤的演化将明显地影响加筋层合板的动力特性。     

含离散源损伤复合材料加筋板的拉伸特性

通过对含有离散源损伤的复合材料加筋板的拉伸试验和有限元模拟,研究了离散源损伤的损伤扩展与破坏特性。结果表明:复合材料加筋板的离散源损伤用穿透蒙皮切断桁条的切口来模拟是合适的,蒙皮上的穿透切口前端有很高的应力集中,桁条被切断导致加筋板传力路线改变;基于Hashin失效准则的渐进损伤有限元数值模拟方法,可以有效地模拟含切口加筋板的宏观损伤扩展和破坏过程,计算结果与试验值吻合较好。      

含分层损伤复合材料加筋层合板的动承载能力

采用有限元方法研究了含穿透分层损伤复合材料加筋层合板的动力响应和承载能力。根据复合材料层合板一阶剪切理论, 推导了复合材料层合板单元的刚度阵和质量阵列式;同时采用Adams 应变能法与Rayleigh阻尼模型相结合的方法, 构造了相应的阻尼阵列式;为了防止在低阶模态中分层处出现的上、下子板不合理的嵌入现象, 建立了含分层损伤复合材料加筋层合板动力分析中分层分析模型和虚拟界面联接模型。并采用Tsai提出的刚度退化准则和动力响应分析的精细积分法, 对在动荷载作用下含分层损伤复合材料加筋层合板结构进行了破坏和承载能力分析。通过典型算例分析, 分别讨论了外载频率、分层深度、筋的位置以及破坏过程中刚度退化对含损伤复合材料加筋层合板动力响应特征和承载能力的影响, 得到了一些具有理论和工程价值的结论。     

简谐激励下复合材料加筋板的基体微裂纹损伤演化

研究了在简谐激励作用下复合材料加筋板基体微裂纹损伤的演化行为及其对加筋板动力特性的影响。基于平均微裂纹密度和断裂力学方法, 建立了复合材料加筋板基体微裂纹演化的刚度退化准则。由于该准则考虑了载荷作用周期数的影响, 从而能够更合理地分析周期性动载荷作用下基体微裂纹损伤演化规律。采用Mindlin一阶剪切理论和复合材料模态阻尼模型, 建立了复合材料加筋板动力分析的有限元方法, 研究了在简谐激励作用下, 含分层损伤复合材料加筋板振动过程中诱发的基体微裂纹损伤的演化、 刚度退化, 频率折减和动力响应。      

含脱粘损伤的复合材料加筋板压缩破坏渐进损伤数值分析

本文提出了基于连续损伤力学的复合材料层合加筋壁板渐进损伤分析模型。该模型采用界面单元模拟筋条和壁板之间的连接界面,连接界面和复合材料层板分别采用Quads准则和Hashin准则作为失效判据,基于内嵌连续损伤状态变量的材料刚度退化方案,采用非线性有限元方法,研究了复合材料加筋壁板在压缩载荷下的破坏过程,分析了结构相应失效模式的细观失效机理。数值分析结果与实验数据吻合较好,证明该方法的合理性和有效性,并详细探讨了界面单元关键参数和层板铺设角度对加筋壁板结构力学响应的影响规律,得到了一些富有价值的结论。     

频率相关自由阻尼层复合材料加筋板动力分析

采用子空间迭代法和精细积分对敷设粘弹性阻尼层的含损伤复合材料加筋板结构进行了频率和动力响应分析。分析中对层合板和层合梁采用了Adams应变能法与Raleigh阻尼模型相结合的阻尼矩阵构造方法;对表面粘弹性阻尼材料则考虑了材料性质和耗散系数对激振频率与温度的依赖性,建立了频率相关粘弹性材料阻尼矩阵的计算方法。通过有限元分析,分别研究了敷设自由阻尼层无损伤和含分层损伤复合材料加筋板的自振频率和模态特征,并根据幅频曲线讨论了阻尼材料模量、耗散系数和阻尼层厚度等因素对结构响应的影响,提出的计算方法对通过合理选择阻尼层材料与几何参数来有效地控制加筋板结构的振动特性,具有一定的参考价值。     

复合材料加筋板低速冲击损伤及剩余压缩强度试验研究

采用落锤法对复合材料加筋板进行了低速冲击损伤（LVI）试验,根据复合材料加筋板构型,设计了冲击支持支架,研究了支持支架的间距对冲击结果的影响;用相同的冲击能量对复合材料加筋板结构中3处典型位置进行冲击,得到不同位置的损伤形貌;分别对完好件和损伤试验件进行压缩试验,将试验结果进行对比,分析不同位置的冲击损伤对结构压缩性能的影响。试验结果表明：在相同的冲击能量下,支持支架间距越小,所造成的冲击损伤越严重;在50 J冲击能量下,筋条区蒙皮处的冲击所造成的损伤不易观察,筋条间蒙皮处的冲击所造成的损伤最为明显,而筋条边缘蒙皮处的冲击可以导致筋条边缘的脱粘;冲击损伤会使加筋板屈曲载荷轻微下降,筋条间蒙皮和筋条区蒙皮冲击损伤对压缩结果影响相对较小,筋条边缘处的冲击会引起损伤处蒙皮的子层屈曲,并影响结构破坏形式,使结构压缩承载能力有较为明显的下降。     

复合材料加筋板低速冲击损伤的数值模拟

建立了复合材料加筋板在横向低速冲击载荷作用下的渐进损伤有限元模型.该模型考虑了复合材料加筋板受低速冲击时的纤维断裂、基体开裂及分层脱粘等五种典型的损伤形式,在层内采用应变描述的失效判据,结合相应的材料性能退化方案,通过编写VUMAT用户自定义子程序以实现相应损伤类型的判断和演化.在层间以及筋条与层板间加入界面元,模拟层间区域的情况,结合传统的应力失效判据和断裂力学中的能量释放率准则来判断分层损伤的起始和演化规律.通过对数值模拟结果与实验数据的比较,验证了模型的合理性和有效性.同时探讨了不同位置、不同冲击能量以及含初始损伤(脱粘)等因素对复合材料加筋板低速冲击性能的影响.     

复合材料加筋板低速冲击损伤的数值模拟

建立了复合材料加筋板在横向低速冲击载荷作用下的渐进损伤有限元模型。该模型考虑了复合材料加筋板受低速冲击时的纤维断裂、基体开裂及分层脱粘等五种典型的损伤形式, 在层内采用应变描述的失效判据, 结合相应的材料性能退化方案, 通过编写VUMAT用户自定义子程序以实现相应损伤类型的判断和演化。在层间以及筋条与层板间加入界面元, 模拟层间区域的情况, 结合传统的应力失效判据和断裂力学中的能量释放率准则来判断分层损伤的起始和演化规律。通过对数值模拟结果与实验数据的比较, 验证了模型的合理性和有效性。同时探讨了不同位置、不同冲击能量以及含初始损伤(脱粘)等因素对复合材料加筋板低速冲击性能的影响。     

含分层损伤的复合材料格栅(AGS)板的非线性热屈曲分析

采用基于复合材料一阶剪切效应理论的有限元法分别研究了含分层损伤的复合材料层合光板、 单向加筋板和格栅加筋(AGS)板的热屈曲性态。在分析中考虑材料热物理性质与温度相关特性, 同时在分层前缘采用了位移约束条件以保证分层区域的各子板的变形相容要求。3种结构的典型算例分析和结果的比较表明, 复合材料格栅(AGS)板具有很强的抗热屈曲的能力, 但是, 分层损伤将使其临界温度降低, 同时还会导致热屈曲的模态发生改变。本文中提出的方法和所得结论对AGS结构的热承载能力预测和损伤容限设计将具有参考价值。      

曲面结构石英纤维增强树脂复合材料分层损伤缺陷太赫兹智能检测

为探索先进预警机雷达罩石英纤维增强树脂复合材料中典型分层缺陷的智能化检测手段,将协作机器人与反射式太赫兹时域光谱系统相结合,搭建了一种基于光纤耦合的反射式太赫兹时域光谱扫查系统,测试所得信噪比的动态范围约60 dB。利用搭建系统对预埋模拟分层缺陷的曲面结构石英纤维增强树脂复合材料样件进行太赫兹无损检测,不同扫描区域获得的反射式太赫兹成像图中均能通过目视辨认出内部预埋缺陷。利用改进的YOLOv4算法在缺陷自动识别中获得90.18%的准确率和91.26%召回率,分别较原YOLOv4算法提高3.37%和4.01%,对小目标缺陷的检测效果良好。实验丰富了预警机雷达罩样件的设计和检测研究内容,探索了曲面结构石英纤维增强树脂复合材料缺陷太赫兹成像,为预警机雷达罩的无损检测提供了新的智能检测工艺,具备工程应用价值。      

Behavior of a flat internal delamination within a fiber reinforced cross-ply composite

A penny-shaped delamination is modeled as a flat octahedral shaped crack between layers of a cross-ply laminate. The fibers of the laminate intersect the edges of the delamination at angles of 0°/90°, +45°/−45°, 90°/0° and −45°/+45° as one proceeds along the delamination edge. Two lay-ups are considered, a cross-ply consisting of two layers, and a symmetric composite, consisting of three layers. The delamination is always between two of the layers. Both tension and shear are applied to the outer boundary of the body. Stress intensity factors about the delamination edge are calculated by means of a conservative M-integral. These are employed to calculate the interface energy release rate and corresponding phase angles. Use is made of existing experimental results to predict the location of propagation along the edge of the delamination. It was found that the most dangerous regions along the delamination front occurred for the 0°/90° or 90°/0° interfaces.     

Enhancement of delamination fatigue resistance in carbon nanotube reinforced glass fiber/polymer composites

We show that the addition of small volume fractions of multi-walled carbon nanotubes (CNTs) to the matrix of glass–fiber composites reduces cyclic delamination crack propagation rates significantly. In addition, both critical and sub-critical inter-laminar fracture toughness values are increased. These results corroborate recent experimental evidence that the incorporation of CNTs improve fatigue life by a factor of two to three in in-plane cyclic loading. We show that in both the critical and sub-critical cases, the degree of delamination suppression is most pronounced at lower levels of applied cyclic strain energy release rate, ΔG. High-resolution scanning electron microscopy of the fracture surfaces suggests that the presence of the CNTs at the delamination crack front slows the propagation of the crack due to crack bridging, nanotube fracture, and nanotube pull-out. Further examination of the sub-critical fracture surfaces shows that the relative proportion of CNT pull-out to CNT fracture is dependent on the applied cyclic strain energy, with pull-out dominating as ΔG is reduced. The conditions for crack propagation via matrix cracking and nanotube pull-out and fracture are studied analytically using fracture mechanics theory and the results compared with data from the experiments. It is believed that the shift in the fracture behavior of the CNTs is responsible for the associated increase in the inter-laminar fracture resistance that is observed at lower levels of ΔG relative to composites not containing CNTs.     

Bending stiffness of composite plates with delamination

Cross-ply GFRP circular plates have been impacted repeatedly at increasing input energies. The global bending stiffness of each plate was measured before and after each impact through quasi-static bending tests. The effects of local thickening as well as matrix cracking and delamination on global bending stiffness have been discussed. Approximate analytical solutions for bending of damaged and undamaged plates under uniform ring load have been obtained. Two types of models have been used to separate the effects of changes in material and geometrical properties on global bending stiffness. The trends of bending stiffness changes have been successfully simulated by analytical calculations.     

Impact analysis of fiber reinforced polymer honeycomb composite sandwich beams

Large scale fiber reinforced polymer (FRP) composite structures have been used in highway bridge and building construction. Recent applications have demonstrated that FRP honeycomb sandwich panels can be effectively and economically applied for both new construction and rehabilitation and replacement of existing structures. This paper is concerned with impact analysis of an as-manufactured FRP honeycomb sandwich system with sinusoidal core geometry in the plane and extending vertically between face laminates. The analyses of the honeycomb structure and components including: (1) constituent materials and ply properties, (2) face laminates and core wall engineering properties, and (3) equivalent core material properties, are first introduced, and these properties for the face laminates and equivalent core are later used in dynamic analysis of sandwich beams. A higher-order impact sandwich beam theory by the authors [Yang MJ, Qiao P. Higher-order impact modeling of sandwich beams with flexible core. Int J Solids Struct 2005;42(20):5460–90] is adopted to carry out the free vibration and impact analyses of the FRP honeycomb sandwich system, from which the full elastic field (e.g., deformation and stress) under impact is predicted. The higher order vibration analysis of the FRP sandwich beams is conducted, and its accuracy is validated with the finite element Eigenvalue analysis using ABAQUS; while the predicted impact responses (e.g., contact force and central deflection) are compared with the finite element simulations by LS-DYNA. A parametric study with respect to projectile mass and velocity is performed, and the similar prediction trends with the linear solution are observed. Furthermore, the predicted stress fields are compared with the available strength data to predict the impact damage in the FRP sandwich system. The present impact analysis demonstrates the accuracy and capability of the higher order impact sandwich beam theory, and it can be used effectively in analysis, design applications and optimization of efficient FRP honeycomb composite sandwich structures for impact protection and mitigation.     

玻璃纤维增强聚合物复合材料筋与工程水泥基复合材料黏结性能

为了研究玻璃纤维增强聚合物（GFRP）复合材料筋和工程水泥基复合材料（ECC）黏结性能的影响因素,对42个GFRP/ECC试件进行了拉拔试验,分析了GFRP复合材料筋表面形式、直径、ECC基体强度及保护层厚度等因素对GFRP复合材料筋与ECC基体黏结性能的影响。结果表明:GFRP/ECC试件的破坏形式主要有拔出破坏、筋剥离剪切破坏、劈裂破坏三种形式。表面带肋GFRP复合材料筋黏结强度比光滑GFRP复合材料筋高约66%;当ECC保护层厚度由1.5D（D为GFRP筋直径）增大至4D时,GFRP/ECC黏结强度提高了约58%;当GFRP复合材料筋直径为12~18 mm时,GFRP/ECC黏结强度随着GFRP复合材料筋直径的增大而降低;ECC强度由33.7 MPa增大至73.3 MPa时,GFRP/ECC黏结强度增大约3倍。增加GFRP复合材料筋表面形式复杂程度,或一定程度上提高ECC基体保护层厚度、提高ECC强度等级,有助于提高GFRP复合材料筋与ECC的黏结强度。