Improving thermal stability of SiC whiskers via nanoscale Ti3SiC2 coatings

Effects of SiC whiskers (SiC_w) on the mechanical properties of composites largely depend on their thermal stability at high temperature. In this study, pure SiC_w and Ti₃SiC₂ coated SiC_w were thermal treated at 1600–1800°C for 1 h. Their phase assemblage, morphology, and structural evolution were investigated. Oxygen partial pressures in the graphite furnace resulted in the breakdown of SiC_w into particles at 1600°C, and the degradation became more pronounced with temperature increasing. The thermal stability of SiC whiskers at 1600–1700°C was significantly improved by a thin Ti₃SiC₂ coating on them, as both thermodynamic calculations and experimental observations suggest Ti₃SiC₂ coating could be preferentially oxidized/decomposed, prior to the active oxidation of SiC. At 1800°C, the protective role of the coating on the whiskers became weakened. SiC was converted into gaseous SiO and CO, with the remaining of interconnected TiC micro-rods and amorphous carbon.     

Wetting behavior and brazing of titanium-coated SiC ceramics using Sn0.3Ag0.7Cu filler

By coating active titanium, Sn0.3Ag0.7Cu (SAC) filler wetted SiC effectively, as the contact angle decreased significantly from ~145° to ~10°. Ti₃SiC₂ and TiO_x (x ≤ 1) reaction layers were formed at the droplet/SiC interface, leading to the reduction of contact angle. Reliable brazing of SiC was achieved using titanium deposition at 900°C for 10 minutes, and the typical interfacial microstructure of Ti-coated SiC/SAC was SiC/TiO_x + Ti₃SiC₂/Sn(s,s). Comparing to direct brazing, Ti–Sn compounds in the brazing seam were effectively reduced and the mechanical property of joints was dramatically improved by titanium coating. The optimal average shear strength of SiC joints reached 25.3 MPa using titanium coating- assisted brazing, which was ∼62% higher than that of SiC brazed joints using SAC-Ti filler directly.     

Residual thermal stress of SiC/Ti3SiC2/SiC joints calculation and relaxed by postannealing

Residual thermal stresses in SiC/Ti₃SiC₂/SiC joining couples were calculated by Raman spectra and simulated by finite element analysis, and then relaxed successfully by postannealing. The results showed that the thermal residual stress between Ti₃SiC₂ and SiC was about on the order of 1 GPa when cooling from 1300°C to 25°C. The thermal residual stresses can be relaxed by the recovery of structure disorders during postannealing. When the SiC/Ti₃SiC₂/SiC joints postannealed at 900°C, the bending strength reached 156.9 ± 13.5 MPa, which was almost twice of the as‐obtained SiC/Ti₃SiC₂/SiC joints. Furthermore, the failure occurred at the SiC matrix suggested that both the flexural strength of joining layer and interface were higher than the SiC matrix.     

In-situ formation of Ti3SiC2 interphase in SiCf/SiC composites by molten salt synthesis

Titanium silicon carbide (Ti₃SiC₂) film was synthesized by molten salt synthesis route of titanium and silicon powder based on polymer-derived SiC fibre substrate. The pre-deposited pyrolytic carbon (PyC) coating on the fibre was utilized as the template and a reactant for Ti₃SiC₂ film. The morphology, microstructure and composition of the film product were characterized. Two Ti₃SiC₂ layers form the whole film, where the Ti₃SiC₂ grains have different features. The synthesis mechanism has been discussed from the thickness of PyC and the batching ratio of mixed powder respectively. Finally, the obtained Ti₃SiC₂ film was utilized as interphase to prepare the SiC fibre reinforced SiC matrix composites (SiC_f/Ti₃SiC₂/SiC composites). The flexural strength (σ_F) and fracture toughness (K_IC) of the SiC_f/Ti₃SiC₂/SiC composite is 460 ± 20 MPa and 16.8 ± 2.4 MPa?m^1/2 respectively.     

Improved oxidation resistance of expanded graphite through nano SiC coating

Expanded graphite with nano SiC and amorphous SiC_xO_y coating was successfully prepared through pyrolysing silane coupling agent (SCA), where the grafting of SCA dominated the final products. The results show that mainly amorphous SiC_xO_y coating covers expanded graphite at 1000 °C, regardless of the SCA concentration. In comparison, nano SiC coating can be synthesized at 1200 °C depending on the good dispersion of SCA (with a SCA concentration of 50 vol%). The formed SiC coating contributes to much higher peak oxidation temperature (812.1 °C) than 678.0 °C of the pure expanded graphite. Meanwhile, the oxidation activation energies of expanded graphite are remarkably improved from 149.15 kJ/mol to 176.16 kJ/mol (based on Kissinger method), attributing to the derived nano SiC and SiC_xO_y coating.     

Effect of silicon/graphite ratio and temperature on oxidation protective properties of SiC/ZrB2–SiC coatings prepared by pack cementation

To investigate the silicon/graphite ratio and temperature on preparation and properties of ZrB₂–SiC coatings, ZrB₂, silicon, and graphite powders were used as pack powders to prepare ZrB₂–SiC coatings on SiC coated graphite samples at different temperatures by pack cementation method. The composition, microstructure, thermal shock, and oxidation resistance of these coatings were characterized and assessed. High silicon/graphite ratio (in this case, 2) did not guarantee higher coating density, instead could be harmful to coating formation and led to the lump of pack powders, especially at temperatures of 2100 and 2200 °C. But residual silicon in the coating is beneficial for high density and oxidation protection ability. The SiC/ZrB₂–SiC (ZS50-2) coating prepared at 2000 °C showed excellent oxidation protective ability, owing to the residual silicon in the coating and dense coating structure. The weight loss of ZS50-2 after 15 thermal shocks between 1500 °C and room temperature, and oxidation for 19 h at 1500 °C are 6.5% and 2.9%, respectively.     

The effects of preparation temperature on the SiCf/SiC 3D4d woven composite

Continuous silicon carbide fiber reinforced silicon carbide matrix (SiC_f/SiC) composites have promising applications in aero-engine due to their unique advantages, such as low density, high modulus and strength, outstanding high temperature resistance and oxidation resistance. As SiC fibers are main reinforcements in SiC_f/SiC composites, the crystallization rate and initial damage degree of SiC fibers are seriously influenced by preparation temperatures of SiC_f/SiC composites, namely mechanical properties of SiC fibers and SiC_f/SiC composites are influenced by preparation temperatures. In this paper, KD-II SiC fibers were woven into 3D4d preforms and SiC matrix was fabricated by PIP process at 1100 °C, 1200 °C, 1400 °C and 1600 °C. Digital image correlation (DIC) method was adopted to measure the uniaxial tensile properties of these SiC_f/SiC composites. In addition, finite element method (FEM) based on representative volume element (RVE) was adopted to predict the mechanical properties of SiC_f/SiC composites. The good agreements between numerical results and experimental results of uniaxial tensile tests verified the validity of the RVE. In last, the transverse tensile, transverse shear, uniaxial shear properties were predicted by this method. The predicted results illustrated that axial tensile, transverse tensile and axial shear properties were greatly influenced by the preparation temperatures of SiC_f/SiC composites while transverse shear properties were not significantly various. And the mechanical properties of SiC_f/SiC composites peaked at 1200 °C among these four temperatures while their values reached their lowest points at 1600 °C because of thermal damage and brittle failure of SiC_f/SiC composites.     

Ti3SiC2 interphase coating in SiCf/SiC composites: Effect of the coating fabrication atmosphere and temperature

The SiC fibers were coated with Ti₃SiC₂ interphase by dip-coating. The Ti₃SiC₂ coated fibers were heat-treated from 900 °C to 1100 °C in vacuum and argon atmospheres to comparatively analyze the effect of temperature and atmosphere on the microstructural evolution and mechanical strength of the fibers. The results show that the surface morphology of Ti₃SiC₂ coating is rough in vacuum and Ti₃SiC₂ is decomposed at 1100 °C. However, in argon atmosphere, the surface morphology is smooth and Ti₃SiC₂ is oxidized at 1000 °C and 1100 °C. At 1100 °C, Ti₃SiC₂ oxidized to form a thin layer of amorphous SiO₂ embedded with TiO₂ grains. Meanwhile, defects and pores appeared in the interphase scale. As a result, the fiber strength treated in the argon was lower than that treated in vacuum. The porous Ti₃SiC₂ interphase fabricated under vacuum was then employed to prepare the SiC_f/SiC mini composite by chemical vapor infiltration (CVI) combined with precursor infiltration pyrolysis (PIP), and can effectively improve the toughness of SiC_f/SiC mini composite. The propagating cracks can be deflected within the porous interphase layer, which promotes fiber pull-outs under the tensile strength.     

Effect of Temperature on Oxidation Behavior of 3‐Dimensional C/SiC Composites Coated by Different Structural SiC and a‐BCx Coatings in Static Wet Oxygen Atmosphere

The effect of temperature on oxidation behavior of 3‐dimensional C/SiC composites coated with SiC and a‐BC_x coatings was investigated. Below 1000°C, C/SiC composites with SiC coating (sample SSS) showed low residual strength, while the composites with a‐BC_x coating (sample BBB) and the composites with a‐BC_x/a‐BC_x/SiC coatings (sample BBS) showed high residual strength. Above 1000°C, samples SSS and BBS showed high residual strength, while sample BBB showed the opposite results. Sample BBS presented better oxidation resistance during 700–1200°C. The oxidation temperature made an effect on self‐sealing mode of sample BBS.     

High temperature properties of the monolithic CVD β-SiC materials joined with a pre-sintered MAX phase Ti3SiC2 interlayer via solid-state diffusion bonding

Monolithic high purity CVD β-SiC materials were successfully joined with a pre-sintered Ti₃SiC₂ foil via solid-state diffusion bonding. The initial bending strength of the joints (∼ 220 MPa) did not deteriorate at 1000 °C in vacuum, and the joints retained ∼ 68 % of their initial strength at 1200 °C. Damage accumulation in the interlayer and some plastic deformation of the large Ti₃SiC₂ grains were found after testing. The activation energy of the creep deformation in the temperature range of 1000 – 1200 °C in vacuum was ∼ 521 kJmol⁻¹. During the creep, the linkage of a significant number of microcracks to form a major crack was observed in the interlayer. The Ti₃SiC₂ interlayer did not decompose up to 1300 °C in vacuum. A mild and well-localized decomposition of Ti₃SiC₂ to TiC_x was found on the top surface of the interlayer after the bending test at 1400 °C in vacuum, while the inner part remained intact.     

Microstructure and mechanical properties of SiC-SiC joints joined by spark plasma sintering

The development of reliable joining technology is of great importance for the full use of SiC. Ti₃SiC₂, which is used as a filler material for SiC joining, can meet the demands of neutron environment applications and can alleviate residual stress during the joining process. In this work, SiC was joined using different powders (Ti₃SiC₂ and 3Ti/1.2Si/2C/0.2Al) as filler materials and spark plasma sintering (SPS). The influence of the joining temperature on the flexural strength of the SiC joints at room temperature and at high temperatures was investigated. Based on X-ray diffraction and scanning electron microscopy analyses, SiC joints with 3Ti/1.2Si/2C/0.2Al powder as the filler material possess high flexural strengths of 133 MPa and 119 MPa at room temperature and at 1200 °C, respectively. The superior flexural strength of the SiC joint at 1200 °C is attributed to the phase transformation of TiO₂ from anatase to rutile.     

Fabrication of Ti3SiC2 and Ti4SiC3 MAX phase ceramics through reduction of TiO2 with SiC

Ti₃SiC₂ and Ti₄SiC₃ MAX phase ceramics were fabricated through high-temperature vacuum reduction of TiO₂ using SiC as a reductant, followed by hot pressing of the products under 25 MPa of pressure at 1600 °C. It was found that both Ti₃SiC₂ and Ti₄SiC₃ may be obtained in good yields, depending on the annealing time during the reduction step. In addition to MAX phases, the products contained some amounts of TiC. The hot pressing step did not significantly affect the composition of the products, indicating good stability of Ti₃SiC₂ and Ti₄SiC₃ under these conditions. Analysis of the densification behavior of the samples revealed lower ductility in Ti₄SiC₃ compared to Ti₃SiC₂. The samples prepared herein exhibited the flexural strength, fracture toughness and microhardness typical of coarse-grained MAX-phase ceramics.     

Green synthesis,formation mechanism and oxidation of Ti3SiC2 powder from bamboo charcoal,Ti and Si

Using low-cost and highly reactive bamboo charcoal, Ti and Si elemental powders as starting materials, Ti₃SiC₂ powder was synthesized via a simple and cost-efficient pressureless sintering technique in argon atmosphere. The influences of synthesis temperature, holding time and Si content on the Ti₃SiC₂ content of the synthesized products were investigated, and the analysis indicated that the relative content of Ti₃SiC₂ reached 98.9 wt% with a molar ratio of 3Ti/1.2Si/2.2C at 1400 °C for 1.5 h. The Ti₃SiC₂ with good crystallinity and homogeneous nanolayered structure was synthesized at lower temperatures due to the high reactivity and high specific surface area of bamboo charcoal. The non-isothermal oxidation behavior showed that Ti₃SiC₂ powder was stable in air below 540 °C. With the temperature increasing up to 1300 °C, continuous and dense TiO₂ and SiO₂ oxidation layers were formed on the surface of Ti₃SiC₂ particles, which conferred good oxidation resistance to Ti₃SiC₂ powder.     

High temperature interfacial phase stability of a Mo/Ti3SiC2 laminated composite

A Mo/Ti₃SiC₂ laminated composite is prepared by spark plasma sintering at 1300 °C under a pressure of 50 MPa. Al powder is used as sintering aid to assist the formation of Ti₃SiC₂. The fabricated composites were annealed at 800, 1000 and 1150 °C under vacuum for 5, 10, 20 and 40 h to study the composite's interfacial phase stability at high temperature. Three interfacial layers, namely Mo₂C layer, AlMoSi layer and Ti₅Si₃ solid solution layer are formed during sintering. Experimental results show that the Mo/Ti₃SiC₂ layered composite prepared in this study has good interfacial phase stability up to at least 1000 °C and the growth of the interfacial layer does not show strong dependence on annealing time. However, after being exposed to 1150 °C for 10 h, cracks formed at the interface.     

Joining of SiCf/SiC using a layered Ti3SiC2-SiCw and TiC gradient filler

A layered filler consisting of Ti₃SiC₂-SiC whiskers and TiC transition layer was used to join SiC_f/SiC. The effects of SiC_w reinforcement in Ti₃SiC₂ filler were examined after joining at 1400 or 1500 °C in terms of the microstructural evolution, joining strength, and oxidation/chemical resistances. The TiC transition layer formed by an in-situ reaction of Ti coating resulted in a decrease in thermal expansion mismatch between SiC_f/SiC and Ti₃SiC₂, revealing a sound joint without cracks formation. However, SiC_f/SiC joint without TiC layer showed formation of cracks and low joining strength. The incorporation of SiC_w in Ti₃SiC₂ filler showed an increase in joining strength, oxidation, and chemical etching resistance due to the strengthening effect. The Ti₃SiC₂ filler containing 10 wt.% SiC_w along with the formation of TiC was the optimal condition for joining of SiC_f/SiC at 1400 °C, showing the highest joining strength of 198 MPa as well as improved oxidation and chemical resistance.     

Microstructure and mechanical properties of hot-pressed SiC nanofiber reinforced SiC composites

This study reports on the preparation and mechanical properties of a novel SiC_nf/SiC composite. The single crystal SiC nanofiber(SiC_nf) reinforced SiC ceramic matrix composites (CMC) were successfully fabricated by hot pressing the mixture of β-SiC powders, SiC_nf and Al–B–C powder. The effects of SiC_nf mass fraction as well as the hot-pressing temperature on the microstructure and mechanical properties of SiC_nf/SiC CMC were systematically investigated. The results demonstrated that the 15 wt% SiC_nf/SiC CMC obtained by hot pressing (HP) at 1850 °C with 30 MPa for 60 min possessed the maximum flexural strength and fracture toughness of 678.2 MPa and 8.33 MPa m^1/2, respectively. The nanofibers pull out, nanofibers bridging and cracks deflection were found by scanning electron microscopy, which are believed can strengthen and toughen the SiC_nf/SiC CMC via consuming plenty of the fracture energy. Besides, although the relative density of the prepared SiC_nf/SiC CMC further increased with the sintering temperature rose to 1900 °C, the further coarsend composites grains results in the deterioration of the mechanical properties for the obtained composites compared to 1850 °C.     

Effect of excess silicon content on the formation of nano-layered Ti3SiC2 ceramic via infiltration of TiC preforms

The aim of this work was to investigate the effect of silicon content on the formation and morphology of Ti₃SiC₂ based composite via infiltration of porous TiC preforms. The gelcasting process was used for fabrication of preforms. It was found that the infiltrated sample at 1500 °C for 90 min from a mixture of 3TiC/1.5Si containing 92 wt.% Ti₃SiC₂. With the increasing of TiC and SiC impurity phases, Vickers hardness was increased to the maximum value of 12.9 GPa in Ti₃SiC₂–39 wt.%TiC composite. Microscopic observations showed that the Ti₃SiC₂ matrix was composed of columnar, platelike and equiaxial grains with respect to silicon content.     

Machinability of Ti3SiC2 with layered structure synthesized by hot pressing mixture of TiCx and Si powder

Nanolaminate Ti₃SiC₂ was synthesized from a mixture of TiC_x (x = 0.67)/Si powder by hot pressing to increase machinability. Ti₃SiC₂ was synthesized at temperatures of 1360 °C and 1420 °C for 90 min under a pressure of 25 MPa. The X-ray diffraction results showed that while mainly Ti₃SiC₂ with some unreacted TiC_x were detected in the synthesized samples at 1360 °C, no phases except Ti₃SiC₂ phases remained in the synthesized samples at 1420 °C. The cutting resistance of Ti₃SiC₂ was measured in terms of the principle, feed, and thrust forces and was compared with that of middle-carbon steel, SM45C. The values of the principal force of the synthesized Ti₃SiC₂ were lower than those of SM45C. After machining, the roughness of the Ti₃SiC₂ was lower than those of SM45C; however, the damage to the tool bit used for the machining of SM45C was less than the damage to those used for the machining of the Ti₃SiC₂.     

Fast seamless joining of SiCw/Ti3SiC2 composite using electric field-assisted sintering technique

A pair of Ti₃SiC₂ reinforced with SiC whiskers (SiC_w/Ti₃SiC₂) composites was successfully joined without any joining materials using electric field-assisted sintering technology at a temperature as low as 1090°C (T_i) and a short time of 30 s. The microstructure and mechanical properties of the obtained SiC_w/Ti₃SiC₂ joints were investigated. The solid-state diffusion was the main joining mechanism, which was facilitated by a relatively high current density (~586 A/cm²) at the joining interface. The shear strength of the sample joined at 1090°C was 51.8 ± 2.9 MPa. The sample joined at 1090°C failed in the matrix rather than at the interface, which confirmed that a sound inter-diffusion bonding was obtained. A rapid and high efficient self-joining process may find application in the case of SiC_w/Ti₃SiC₂ sealing cladding tube and end cap.     

Microstructure and mechanical strength of transient liquid phase bonded Ti3SiC2 joints using Al interlayer

Based on the structure characteristic of Ti₃SiC₂ and the easy formation of Ti₃Si_1−xAl_xC₂ solid solution, a transient liquid phase (TLP) bonding method was used for bonding layered ternary Ti₃SiC₂ ceramic via Al interlayer. Joining was performed at 1100–1500 °C for 120 min under a 5 MPa load in Ar atmosphere. SEM and XRD analyses revealed that Ti₃Si(Al)C₂ solid solution rather than intermetallic compounds formed at the interface. The mechanism of bonding is attributed to aluminum diffusing into the Ti₃SiC₂. The strength of joints was evaluated by three point bending test. The maximum flexural strength reaches a value of 263 ± 16 MPa, which is about 65% of that of Ti₃SiC₂; for the sample prepared under the joining condition of 1500 °C for 120 min under 5 MPa. This flexural strength of the joint is sustained up to 1000 °C.