共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
4.
5.
铅酸蓄电池生产过程中,和膏后和极板固化后铅膏的物相组成、微观结构对成品蓄电池的性能会产生直接的影响。所以,在实际生产中,除了需要关注和膏后铅膏的稳定性、一致性之外,还要随时关注固化生极板铅膏在不同搁置条件下物相的变化,以及结构性能。本文中,笔者利用X射线衍射仪(DX2700),邵氏硬度计(LX-D型)对和膏时和固化后铅膏不同搁置条件下的物相组成,以及正生板的硬度进行了跟踪分析。 相似文献
6.
7.
8.
9.
10.
分析了风能、太阳能独立发电系统储能蓄电池的使用状况,探讨了储能蓄电池使用环境对蓄电池的要求,认为储能蓄电池开发和应用面临着很多困难,需从板栅合金、铅膏配方、固化、化成等各工序进行分析研究,力争有所突破。 相似文献
11.
12.
特高压线路工频参数测试干扰分析是选择适合工频参数测试方法及测试结果分析的重要基础。测试了1 000 kV皖南-浙北特高压线路正序和零序参数测试期间的干扰电压信号,分析了其频谱特征;在此基础上,通过与正序参数仿真计算值的对比分析了正序参数实际测试偏差。结果表明:皖南-浙北特高压同塔双回线路工频参数测试期间,干扰电压存在“三相不平衡性及时变性”的特点;工频法和异频法2种不同方法得到的线路参数测试结果存在一定差异;干扰电压“时变”时,线路工频参数测试宜采用异频法。 相似文献
13.
《国外电子测量技术》2014,(10)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world’s premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
14.
电站锅炉停用保护剂多采用十八胺和表面活性胺。对这2种停用保护剂进行了应用效果对比研究,即对湿冷机组、空冷机组采用十八胺或表面活性胺、有无凝结水精处理系统等6台机组停机和启动过程中给水、主蒸汽和凝结水的氢电导率变化情况进行分析。研究结果表明:在停机过程和启动过程,2种保护剂均会在水汽系统中发生部分分解,导致水汽系统的氢电导率显著升高;表面活性胺和十八胺比较,使用前者,机组启停机过程可保持凝结水精处理系统正常投运,因而可使水汽质量迅速达标,对机组安全运行有利,因此推荐采用表面活性胺作为锅炉停用保护剂。 相似文献
15.
《国外电子测量技术》2014,(9)
正Qingdao,China7.16-19,2015The International Conference on Electronic MeasurementInstruments(ICEMI)is the world's premier conference dedicated to the electronic measurement and test of devices,boards and systems that is covering the complete cycle from design,verification,test,diagnosis,failure analysis and process of manufactory and products 相似文献
16.
17.
18.
19.
S. Y. Wu B. N. Tran F. Y. Davis C. L. Trent D. L. Edberg W. A. Geideman 《Integrated ferroelectrics》2013,141(3):281-291
Abstract Smart materials of lead-zirconate-titanate (PZT) piezoelectric ceramics have attracted attention in recent years for active vibration control, acoustic noise suppression, health monitoring and damage assessment. We at McDonnell Douglas Aerospace have been studying these ceramics for use as sensors and actuators in various space and aircraft structures. In this paper, we will report results of a recent study on active vibration control using monomorph PZT actuators. The experiments were performed on thin aluminum cantilever beams. Collocated and non-collocated sensors and actuators were employed. Two control techniques: the classical velocity feedback and adaptive feedback controls, were investigated. We have obtained significant damping and broadband vibration attenuation of greater than 30 dB using the classical control with the single-input single-output feedback approach. A 24 dB reduction has also been achieved using the adaptive control with the multiple-input single-output approach. Detailed experimental methods and results will be described. 相似文献