Structural and electrical properties of radio frequency magnetron sputtered tantalum oxide films: Influence of post-deposition annealing

The as-deposited and annealed radio frequency reactive magnetron sputtered tantalum oxide (Ta₂O₅) films were characterized by studying the chemical binding configuration, structural and electrical properties. X-ray photoelectron spectroscopy and X-ray diffraction analysis of the films elucidate that the film annealed at 673 K was stoichiometric with orthorhombic β-phase Ta₂O₅. The dielectric constant values of the tantalum oxide capacitors with the sandwich structure of Al/Ta₂O₅/Si were in the range from 14 to 26 depending on the post-deposition annealing temperature. The leakage current density was <20 nA cm^?2 at the gate bias voltage of 0.04 MV/cm for the annealed films. The electrical conduction mechanism observed in the films was Poole–Frenkel.     

Effect of thickness on the structural,optical and electrical properties of RF magnetron sputtered GZO thin films

Gallium-doped zinc oxide (GZO) thin films with very high conductivity and transparency were successfully deposited by RF magnetron sputtering at a substrate temperature of 400 °C. The dependence of the film properties over the thickness was investigated. X-ray diffraction (XRD) results revealed the polycrystalline nature of the films with hexagonal wurtzite structure having preferential orientation along [001] direction normal to the substrate. The lowest resistivity obtained from electrical studies was 5.4×10⁻⁴ Ω cm. The optical properties were studied using a UV–vis spectrophotometer and the average transmittance in the visible region (400–700 nm) was found to be 92%, relative to the transmittance of a soda–lime glass reference for a GZO film of thickness 495 nm and also the transparency of the films decreases in the near IR region of the spectra. The mobility of the films showed a linear dependence with crystallite size. GZO film of thickness 495 nm with the highest figure of merit indicates that the GZO film is suitable as an ideal transparent conducting oxide (TCO) material for solar cell applications.     

Effect of rapid thermal annealing of sputtered aluminium nitride film in an oxygen ambient

Aluminium nitride (AlN) thin films were deposited by radio frequency (RF) magnetron sputtering on p-type silicon (Si) substrate of (1 0 0) orientation using only argon (Ar) gas at substrate temperature of 300 °C. In order to achieve improved electrical properties, we performed post-deposition rapid thermal annealing (RTA). Sputtered AlN films were annealed in an oxygen ambient at temperatures of 600, 700, and 800 °C using RTA for 30 min. The orientation of the AlN crystal in the film was investigated using X-ray diffraction (XRD). The characteristic spectra by functional group were analyzed by Fourier transformation infrared (FTIR) spectroscopy. The electrical properties of the AlN thin films were studied through capacitance–voltage (C–V) characteristics in metal–insulator–semiconductor (MIS) device using the films as insulating layers. The flatband voltages (V_FB) in C–V curves were found to depend on crystal orientations. Negative V_FB was found in the case when AlN (1 0 0) peak was found. Also, when AlN (1 0 3) peak was observed upon increasing the annealing temperature, the value of V_FB was positive and after annealing at 700 °C, AlN (1 0 3) peak intensity was found to be maximum and V_FB was as high as+6.5 V.     

Effects of substrate temperature on electrical and structural properties of copper thin films

This paper addresses the effects of substrate temperature on electrical and structural properties of dc magnetron sputter-deposited copper (Cu) thin films on p-type silicon. Copper films of 80 and 500 nm were deposited from Cu target in argon ambient gas pressure of 3.6 mTorr at different substrate temperatures ranging from room temperature to 250 °C. The electrical and structural properties of the Cu films were investigated by four-point probe and atomic force microscopy. Results from our experiment show that the increase in substrate temperature generally promotes the grain growth of the Cu films of both thicknesses. The RMS roughness as well as the lateral feature size increase with the substrate temperature, which is associated with the increase in the grain size. On the other hand, the resistivity for 80 nm Cu film decreases to less than 5 μΩ-cm at the substrate temperature of 100 °C, and further increase in the substrate temperature has not significantly decreased the film resistivity. For the 500 nm Cu films, the increase in the grain size with the substrate temperature does not conform to the film resistivity for these Cu films, which show no significant change over the substrate temperature range. Possible mechanisms of substrate-temperature-dependent microstructure formation of these Cu films are discussed in this paper, which explain the interrelationship of grain growth and film resistivity with elevated substrate temperature.     

Effects of thermal annealing on the structural properties of sputtered W–Si–N diffusion barriers

W–Si–N thin films were deposited via rf-magnetron sputtering from a W₅Si₃ target in Ar/N₂ reactive gas mixtures over a large range of compositions, obtained by varying the partial flow of nitrogen within the reaction chamber. The samples of each set were then thermally annealed in vacuum at different temperatures up to 980 °C.Film composition was determined by Rutherford backscattering spectrometry (RBS), surface film morphology by scanning electron microscopy (SEM), micro-structure by transmission electron microscopy (TEM), vibrational properties by FT-IR absorption and Raman scattering spectroscopy, and electrical resistivity by four-point probe measurements.Independently of the deposition conditions, all the as-deposited films have an amorphous structure, while their composition varies, showing an increase of Si/W ratio from 0.1 up to 0.55 when the nitrogen concentration in the films increases from 0 to 60 at%. Thermal treatments in vacuum induce an important loss of nitrogen in the nitrogen-rich samples, especially at temperatures higher than 600 °C. Samples with high nitrogen content preserve their amorphous structure even at the highest annealing temperature, despite the chemical bonding ordering observed by means of FT-IR measurements. Raman spectroscopy of as-deposited films rich in nitrogen suggests the presence of an important amorphous silicon nitride component, but fails to detect any structural rearrangement either within the composite matrix of film or within silicon nitride component. Segregation of metallic tungsten was detected by TEM in the annealed sample with lowest nitrogen content (W₅₈Si₂₁N₂₁). Finally, the resistivity of the films increases with the N content, while the loss of nitrogen accompanies the decrease of resistivity especially of samples with high nitrogen content.     

Thickness dependence of the structural and electrical properties of copper films deposited by dc magnetron sputtering technique

This paper addresses the influences of film thickness on structural and electrical properties of dc magnetron sputter-deposited copper (Cu) films on p-type silicon. Cu films with thicknesses of 130-1050 nm were deposited from Cu target at sputtering power of 125 W in argon ambient gas pressure of 3.6 mTorr at room temperature. The electrical and structural properties of the Cu films were investigated by four-point probe, atomic force microscopy (AFM) as well as X-ray diffraction (XRD). Results from our experiment show that the grain grows with increasing film thickness, along with enhanced film crystallinity. The root mean square (RMS) roughness as well as the lateral feature size increase with the Cu film thickness, which is associated with the increase in the grain size. On the other hand, the Cu film resistivity decreases to less than 5 μΩ-cm for 500 nm thick film, and further increase in the film thickness has no significant effects on the film resistivity. Possible mechanisms of film thickness dependent microstructure formation of these Cu films are discussed in the paper, which explain the interrelationship of grain growth and film resistivity with increasing Cu film thickness.     

Effect of annealing temperature on structural,electrical and optical properties of spray pyrolytic nanocrystalline CdO thin films

Nanocrystalline CdO thin films were prepared onto a glass substrate at substrate temperature of 300 °C by a spray pyrolysis technique. Grown films were annealed at 250, 350, 450 and 550 °C for 2.5 h and studied by the X-ray diffraction, Hall voltage measurement, UV-spectroscopy, and scanning electron microscope. The X-ray diffraction study confirms the cubic structure of as-deposited and annealed films. The grain size increases whereas the dislocation density decreases with increasing annealing temperature. The Hall measurement confirms that CdO is an n-type semiconductor. The carrier density and mobility increase with increasing annealing temperature up to 450 °C. The temperature dependent dc resistivity of as-deposited film shows metallic behavior from room temperature to 370 K after which it is semiconducting in nature. The metallic behavior completely washed out by annealing the samples at different temperatures. Optical transmittance and band gap energy of the films are found to decrease with increasing annealing temperature and the highest transmittance is found in near infrared region. The refractive index and optical conductivity of the CdO thin films enhanced by annealing. Scanning electron microscopy confirms formation of nano-structured CdO thin films with clear grain boundary.     

Electrical properties of zinc oxide sputtered thin films

ZnO thin films were deposited on silicon substrate by rf magnetron sputtering from metallic zinc target. The electrical properties of ZnO are currently being studied. In this work, measurements of the ac conductivity properties of ZnO sandwich structures with silver and platinum electrodes are reported. The frequency dependence of both the ac conductivity and dielectric constant of thin films of ZnO have been investigated in the frequency range 5 kHz-13 MHz. It is shown that the total ac conductivity σ(ω), obeys the equation σ(ω)=Aω^S where s is an index which increases with frequency and decreases with temperature. It appears that for ZnO films, the conduction mechanism is thermally activated and both the overlap large polaron tunnelling and the correlated barrier-hopping of charge carrier over localized states fit the experimental data. The dielectric constant, ε_r, lies in the range 8-9 at room temperature and is independent of the frequency in the dielectric thin films.     

Effect of processing parameter on structural,optical and electrical properties of photovoltaic chalcogenide nanostructured RF magnetron sputtered thin absorbing films

The aim of this work was to develop high quality of CuIn_1−xGa_xSe₂ thin absorbing films with x (Ga/In+Ga)<0.3 by sputtering without selenization process. CuIn_0.8Ga_0.2Se₂ (CIGS) thin absorbing films were deposited on soda lime glass substrate by RF magnetron sputtering using single quaternary chalcogenide (CIGS) target. The effect of substrate temperature, sputtering power & working pressure on structural, morphological, optical and electrical properties of deposited films were studied. CIGS thin films were characterised by X-ray diffraction (XRD), Field emission scanning electron microscope (FE-SEM), Energy dispersive X-ray spectroscopy (EDAX), Atomic force microscopy (AFM), UV–vis–NIR spectroscopy and four probe methods. It was observed that microstructure, surface morphology, elemental composition, transmittance as well as conductivity of thin films were strongly dependent on deposition parameters. The optimum parameters for CIGS thin films were obtained at a power 100 W, pressure 5 mT and substrate temperature 500 °C. XRD revealed that thin film deposited at above said parameters was polycrystalline in nature with larger crystallite size (32 nm) and low dislocation density (0.97×10¹⁵ lines m⁻²). The deposited film also showed preferred orientation along (112) plane. The morphology of the film depicted by FE-SEM was compact and uniform without any micro cracks and pits. The deposited film exhibited good stoichiometry (Ga/In+Ga=0.19 and In/In+Ga=0.8) with desired Cu/In+Ga ratio (0.92), which is essential for high efficiency solar cells. Transmittance of deposited film was found to be very low (1.09%). The absorption coefficient of film was ~10⁵ cm⁻¹ for high energy photon. The band gap of CIGS thin film evaluated from transmission data was found to be 1.13 eV which is optimum for solar cell application. The electrical conductivity (7.87 Ω⁻¹ cm⁻¹) of deposited CIGS thin film at optimum parameters was also high enough for practical purpose.     

Effect of rapid thermal annealing on pentacene-based thin-film transistors

The bottom contact pentacene-based thin-film transistor is fabricated, and it is treated by rapid thermal annealing (RTA) with the annealed temperature up to 240 °C for 2 min in the vacuum of 1.3 × 10⁻² torr. The morphology and structure for the pentacene films of OTFTs were examined by scanning electron microscopy and X-ray diffraction technique. The thin-film phase and a very small fraction of single-crystal phase were found in the as-deposited pentacene films. While the annealing temperature increases to 60 °C, the pentacene molecular ordering was significantly improved though the grain size only slightly increased. The device annealed at temperature of 120 °C has optimal electrical properties, being consistent with the experimental results of XRD. The post-annealing treatment results in the enhancement of field-effect mobility in pentacene-based thin-film transistors. The field-effect mobility increases from 0.243 cm²/V s to 0.62 cm²/V s. Besides, the threshold voltage of device shifts from −7 V to −3.88 V and the on/off current ratio increases from 4.0 × 10³ to 8.7 × 10³.     

Electrical characterization and morphological properties of AlN films prepared by dc reactive magnetron sputtering

Aluminum nitride (AlN) films were deposited by dc reactive magnetron sputtering on p-Si-(1 0 0) substrate in Ar-N₂ gas mixtures. The effects of nitrogen concentration and sputtering power on AlN films deposition rate, crystallographic orientation, refractive index, and surface morphology are investigated by means of several characterization techniques. The results show that AlN films reasonably textured in (0 0 2) orientation with low surface roughness can be obtained with the deposition rate as high as 70 nm/min by the control of either target power or N₂ concentration in the gas mixture. Increasing the dc discharge power, Al atoms are not completely nitridized and the Al phases appear, as well as the AlN phases. MIS (Metal-Insulator-Semiconductor) structures were fabricated and electrically evaluated by I-V (current-voltage) and C-V (capacitance-voltage) measurements at high frequency (1 MHz). The results obtained from C-V curves indicate that charges at the dielectric/semiconductor interface occur, and the dielectric constant values (extracted under strong accumulation region) are compatible with those found in literature.     

退火对纳米VO2薄膜结构及电性能的影响

采用直流反应磁控溅射法在K9玻璃和DBr衬底上制备了VO2薄膜.利用扫描电镜(SEM)、X射线衍射(XRD)、傅里叶红外光谱(FT-IR)对薄膜的形貌、晶相和分子结构等进行分析.结果表明,在氧气气氛下退火后,薄膜颗粒变得清晰可见,平均尺寸约25 nm,薄膜由非晶态结构转变为晶态的VO2,且在(011)方向出现明显择优取...     

Optical,morphological and electrical studies of Zn:PbS thin films

Structural, electrical, and optical properties of undoped and Zn doped lead sulfide (PbS) thin films are benign reported in this paper. The subjected films were grown on glass substrates at 25 °C by a chemical bath deposition (CBD) method. The concentration of Zn in the deposition bath represented by the ratio [Zn²⁺]/[Pb²⁺] was varied from 0% to 5%. It was found that the film׳s grains decreased in size with increasing Zn content in the film. XRD data showed the polycrystalline nature of the film its crystal orientation peak intensities decreased with higher doping concentration of Zn. Atomic force microscopy (AFM) measurements revealed that the surface roughness of the films decreased due to zinc doping as well. However, with increasing of the dopant concentration from 0% to 5%, the average transmittance of the films varied over the range of 35–75%. The estimated optical band (E_g) gaps of undoped and Zn doped PbS thin films were in the range of 0.72–1.46 eV. Hall Effect measurements electrical resistivity, carrier concentration and Hall mobility have been determined for the titled film as functions on the Zn content within the film׳s textures. The overall result of this work suggested that the Zn:PbS film is a good candidate as an absorber layer in the modern solar cell devices.     

Effect of thermal annealing on the electrical properties of P3HT:PC70BM nanocomposites

We studied the electrical properties of organic photovoltaic (OPV) devices based on poly (3-hexylthiophene) and fullerene derivative [6, 6]-Phenyl-C₇₀-butyric acid methyl ester nanocomposite (P3HT:PC₇₀BM) as a function of the annealing temperature. Thermal annealing enables crystallization of the polymer and diffusion of the PC₇₀BM molecules. Diode parameters, such as the barrier height ϕ_b and the ideality factor n were calculated. They were found to be depend strongly on the annealing temperature. This dependence is attributed to surface states, inhomogeneity in the material and series resistance. Best OPV devices had a short circuit current density of 3.35 mA/cm², an open circuit voltage of 0.68 V, a fill factor of 0.45, and a power conversion efficiency of 2.2%, by applying a thermal annealing temperature of 150 °C for 10 min.     

Influence of thermal annealing on electrical and optical properties of indium tin oxide thin films

Transparent conducting indium tin oxide (ITO) thin films with the thickness of 300 nm were deposited on quartz substrates via electron beam evaporation, and five of them post-annealed in air atmosphere for 10 min at five selected temperature points from 200 °C to 600 °C, respectively. An UV–vis spectrophotometer and Hall measurement system were adopted to characterize the ITO thin films. Influence of thermal annealing in air atmosphere on electrical and optical properties was investigated in detail. The sheet resistance reached the minimum of 6.67 Ω/sq after annealed at 300 °C. It increased dramatically at even higher annealing temperature. The mean transmittance over the range from 400 nm to 800 nm reached the maximum of 89.03% after annealed at 400 °C, and the figure of merit reached the maximum of 17.79 (Unit: 10⁻³ Ω⁻¹) under the same annealing condition. With the annealing temperature increased from 400 °C to 600 °C, the variations of transmittance were negligible, but the figure of merit decreased significantly due to the deterioration of electrical conductivity. With increasing the annealing temperature, the absorption edge shifted towards longer wavelength. It could be explained on the basis of Burstein–Moss shift. The values of optical band gap varied in the range of 3.866–4.392 eV.     

Properties of ZnO/Cu/ZnO multilayer films deposited by simultaneous RF and DC magnetron sputtering at different substrate temperatures

ZnO/Cu/ZnO transparent conductive multilayer films are prepared by simultaneous RF sputtering of ZnO and DC sputtering of Cu. The properties of the multilayer films are studied at different substrate temperatures. Sheet resistance of the multilayer film decreased initially with increase of substrate temperature and increased further with increase of substrate temperature beyond 100 °C. However, transmittance of the multilayer film increased with increase of substrate temperature. Good transparent conductive film of sheet resistance 9.3 Ω/sq and transmittance of 85% was found at a substrate temperature of 100 °C. The performance of the multilayer film was evaluated using a figure of merit. The observed property of the multilayer film is suitable for the application of transparent conductive electrodes.     

Ni dependent structural,optical and electrical properties of CuO nanostructures

The present work reports the synthesis of Cu_1-xNi_xO (x = 0%, 3%, 6% and 9%) nanoparticles by co-precipitation method and correlates the effect of nickel on structural, optical and electrical properties. A phase separation into cubic NiO was observed at the higher nickel concentration of 9%. The difference in ionic radii between copper and nickel resulted in the lattice contraction. The mean crystallite size and strain values were found to be varying with respect to nickel concentration. Raman spectroscopy studies exhibited the emergence of 1LO peak on 9% doping due to the phase separation into NiO. The band gap energy calculated using diffuse reflectance spectra indicated a narrowing of band gap with the increase in nickel content. AC impedance measurement showed a maximum conductivity of 2.13 × 10⁻² S/cm at 600 °C for Cu_0.94Ni_0.06O. Further, a lower activation energy was noticed for 6% which increased at 9% Ni presence. The dielectric constant was found to be increasing till 6% and decreases with higher nickel content (9%). The present work clearly demonstrates the beneficial role of nickel in the form of a doped structure while it becomes detrimental upon phase separation.     

富汞热处理对碲镉汞电学性能的影响

对液相外延方法(LPE)生长的碲镉汞(HgCdTe)材料进行了闭管富汞热处理,并研究了不同的热处理时间和热处理温度对碲镉汞材料电学性能的影响。HgCdTe材料经过富汞热处理后可以有效降低材料内的缺陷尺寸和密度。该方法不仅可以降低材料内的位错密度,而且还可以完成材料P型到N型的转变。工艺中的低温热处理对HgCdTe材料的电学性能有较大影响。研究发现,随着低温热处理时间的持续增加,HgCdTe材料的载流子浓度会明显增加。而当低温热处理温度在210℃~250℃范围内变化时,若保持低温热处理时间不变,则热处理后HgCdTe材料的载流子浓度在一定范围内波动,且无明显变化。通过对HgCdTe器件进行I-V曲线测试以及最终的组件测试,发现热处理后载流子浓度在1E13~1E14cm^-3范围内的HgCdTe芯片就可以得到很好的测试结果。     

Effect of sputter deposited Zn precursor film thickness and annealing time on the properties of Cu2ZnSnS4 thin films deposited by sequential reactive sputtering of metal targets

Cu₂ZnSnS₄ (CZTS) is made of earth abundant elements and also have suitable optical properties for solar cell applications. But, in phase diagram, CZTS exists in a narrow range of temperature and composition. Therefore, optimizing the elemental composition and annealing time is very important for obtaining phase pure CZTS. In this study, the effects of elemental composition and short annealing time on the structural and optical properties of reactively sputtered CZTS thin films are reported. Thin films were deposited by reactive sputtering of Cu: Sn (60:40 wt%), Sn and Zn targets sequentially in the presence of H₂S at room temperature. Amount of Zn precursor was varied by changing the sputter time for Zn. The films were rapidly annealed in inert atmosphere for varying time. The band gap of sample changed with change in the composition as well as annealing time. Sample with higher Zn content showed better crystallinity. With increase in the annealing time the crystallinity of samples improved. Sample annealed for 12 min at 550 °C was phase pure. Obtaining good quality film even for very short anneal time is the novelty of reactive sputtering method as all the elements are already mixed and short annealing is required only for crystal growth. Through detailed experiments, the optimum composition and annealing time required for the growth of phase pure CZTS has been established.     

Rapid thermal annealing of cerium dioxide thin films sputtered onto silicon (111) substrates: Influence of heating rate on microstructure and electrical properties

The impact of the heating rate (HR) of a Rapid Thermal Annealing (RTA) on the crystallinity and on the morphology of CeO₂ thin films has been investigated by Raman Spectroscopy (RS), Photoluminescence (PL), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), and tapping mode Atomic Force Microscopy (AFM). The electrical properties of CeO₂ thin films have also been studied with the Conductive AFM mode. This paper highlights the importance of the heating rate value used during an RTA on crystalline quality, morphology and on the electrical properties of the CeO₂ layer. In fact, the best crystallinity with a good morphology and a high resistivity has been obtained for a CeO₂ layer sputtered on (111) Si substrate and post-annealed at 1000 °C for 30 s with an HR of 25 °C/s.