Enhanced mechanical and dielectric properties of SiCf/SiC composites with silicon oxycarbide interphase

SiC_f/SiC composites with silicon oxycarbide (SiOC) interphase were successfully prepared using silicone resin as interphase precursor for dip-coating process and polycarbosilane as matrix precursor for PIP process assisted with hot mold pressing. The effects of SiOC interphase on mechanical and dielectric properties were investigated. XRD and Raman spectrum results show that SiOC interphase is composed of silicon oxycarbide and free carbon with a relatively low crystalline degree. The surface morphology of SiC fibers with SiOC interphase is smooth and homogeneous observed by SEM. The flexural strength and failure displacement of SiC_f/SiC composites with SiOC interphase vary with the thickness of interphase and the maximum value of flexural strength is 289 MPa with a failure displacement of 0.39 mm when the thickness of SiOC interphase is 0.25 µm. The complex permittivity of the composites increases from 8.8-i5.7 to 9.8-i8.3 with the interphase thicker.     

Microstructure and ablation behavior of SiC coated C/C–SiC–ZrC composites prepared by a hybrid infiltration process

In this study, C/C–SiC–ZrC composites coated with SiC were prepared by precursor infiltration pyrolysis combined with reactive melt infiltration. The pyrolysis behavior of the hybrid precursor was investigated using thermal gravimetric analysis-differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy techniques. The microstructure and ablation behavior of the composites were also investigated. The results indicate that the composites exhibit an interesting structure, wherein a ceramic coating composed of SiC and a small quantity of ZrC covers the exterior of the composites, and the SiC–ZrC hybrid ceramics are partially embedded in the matrix pores and distributed around the carbon fibers as well. The composites exhibit good ablation resistance with a surface temperature of over 2300 °C during ablation. After ablation for 120 s, the mass and linear ablation rates of the composites are 0.0026 g/s and 0.0037 mm/s, respectively. The great ablation resistance of the composites is attributed to the formation of a continuous phase of molten SiO₂ containing SiC and ZrO₂, which seals the pores of the composites during ablation.     

Ablation behavior and mechanism of C/C–ZrC–SiC composites under an oxyacetylene torch at 3000 °C

C/C–ZrC–SiC composites with continuous ZrC–SiC ceramic matrix were prepared by a multistep technique of precursor infiltration and pyrolysis process. Ablation properties of the composites were tested under an oxyacetylene flame at 3000 °C for 120 s. The results show that the linear ablation rate of the composites was about an order lower than that of pure C/C and C/C–SiC composites as comparisons, and the mass of the C/C–ZrC–SiC composites increased after ablation. Three concentric ring regions with different coatings appeared on the surface of the ablated C/C–ZrC–SiC composites: (i) brim ablation region covered by a coating with layered structure including SiO₂ outer layer and ZrO₂–SiO₂ inner layer; (ii) transition ablation region, and (iii) center ablation region with molten ZrO₂ coating. Presence of these coatings which acted as an effective oxygen and heat barrier is the reason for the great ablation resistance of the composites.     

Effect of PyC interphase thickness on mechanical and ablation properties of 3D Cf/ZrC–SiC composite

Three-dimensional (3D) C_f/ZrC–SiC composites were successfully prepared by the polymer infiltration and pyrolysis (PIP) process using polycarbosilane (PCS) and a novel ZrC precursor. The effects of PyC interphase of different thicknesses on the mechanical and ablation properties were evaluated. The results indicate that the C_f/ZrC–SiC composites without and with a thin PyC interlayer of 0.15 µm possess much poor flexural strength and fracture toughness. The flexural strength grows with the increase of PyC layer thickness from 0.3 to 1.2 µm. However, the strength starts to decrease with the further increase of the PyC coating thickness to 2.2 µm. The highest flexural strength of 272.3±29.0 MPa and fracture toughness of 10.4±0.7 MPa m^1/2 were achieved for the composites with a 1.2 µm thick PyC coating. Moreover, the use of thicker PyC layer deteriorates the ablation properties of the C_f/ZrC–SiC composites slightly and the ZrO₂ scale acts as an anti-ablation component during the testing.     

Enhanced mechanical and microwave-absorption properties of SiCf/AlPO4 composite with PIP–SiC interphase and the MWCNTs filler

A single-layer radar-absorbing structure in the X-band (8.2 GHz to 12.4 GHz) was designed and fabricated by blending multi-walled carbon nanotubes (MWCNTs) with the binder matrix of SiC fiber/aluminum phosphate matrix (SiC_f/AlPO₄) composite. The SiC interphase was successfully prepared on SiC fibers by a precursor infiltration and pyrolysis (PIP) method. The morphology of as-received interphase was observed by SEM, and its structure was characterized by XRD and Raman spectrum. The effects of PIP–SiC interphase on the mechanical and dielectric properties of the composite were investigated. The influence of MWCNTs content on the dielectric and microwave-absorption properties of coated SiC_f/AlPO₄ composite was discussed. When the content of MWCNTs was between 1.5 wt% and 3.5 wt% and the composite thickness is in the range of 2.5–3.5 mm, the SiC_f/AlPO₄ composite achieved excellent absorbing wave property in X-band.     

Fabrication and mechanical properties of SiC composites toughened by buckypaper and carbon fiber fabrics alternately laminated

SiC ceramics, for the first time, were toughened with nano scale carbon nanotubes (CNTs) buckypapers and micro scale carbon fibers within this work. The CNTs buckypapers were alternately laminated with carbon fiber fabrics (C_fb) to a preform by needle punched in Z-direction. Afterwards, the buckypaper-C_fb/SiC composites were obtained by infiltrating of SiC into the as-laminated preform via chemical vapor infiltration (CVI). Some effects of different lamination thickness and CVI times on the mechanical properties of the composites were investigated. Results showed that the maximum flexural strength and work of fracture of the buckypaper-C_fb/SiC composites reached 262.4 MPa and 4.15 kJ m⁻², respectively, when the thickness reached about 3.50 mm. Compared to C_fb/SiC composites without buckypapers, the strength and work of fracture of the buckypaper-C_fb/SiC composites increased by 19.8% and 111.7%, respectively. Densified composites can be obtained after CVI for 8 times. A main factor affecting the mechanical properties of buckypaper-C_fb/SiC composites is the degree of densification. Introducing nano scale CNTs and micro scale carbon fibers reaches a multiscale co-toughening effect. Meanwhile, a sandwich structure ceramic matrix composite with high-CNT concentration was obtained in this work.     

Si/SiC coated Cf/SiC composites via tape casting and reaction bonding: The effect of carbon content

In this paper, a novel surface modification method for C_f/SiC composites is proposed. Si/SiC coating on C_f/SiC composites is prepared by tape casting and reaction bonding method. The effects of carbon content on the rheological property of the slurries along with the microstructure of the sintered coatings are investigated. The best result has been obtained by infiltrating liquid silicon into a porous green tape with a carbon density of 0.84 g/cm³. In addition, the effect of sintering parameters on the phase composition of the coatings is studied. Dense Si/SiC coating with high density as well as strong bonding onto the substrate is obtained. This Si/SiC coating exhibits an excellent mechanical property with HV hardness of 16.29±0.53 GPa and fracture toughness of 3.01±0.32 MPa m^1/2. Fine surface with roughness (RMS) as low as 2.164 nm is achieved after precision grinding and polishing. This study inspires a novel and effective surface modification method for C_f/SiC composites.     

Mechanical properties of ceramic matrix composites with siloxane matrix and liquid phase coated carbon fiber reinforcement

In order to evaluate the benefits of continuous liquid phase coating (CLPC) for carbon fibers, coated fibers as well as uncoated fibers were applied in the preparation of unidirectionally reinforced ceramic matrix composites (CMCs) with polysiloxane based matrix. Fibers coated with precursor based ceramic or carbon coatings were transferred into prepregs by continuous fiber impregnation with liquid polysiloxane and filament winding. The wet prepregs were cut to shape, laminated and then pressed and cured in the mold at 150 °C for 1 h. The cured polymeric matrix composites were calcined and densified by subsequent precursor infiltration/calcination cycles. The flexural strength of the CMCs was measured by 4-point bending tests, the microstructure was determined by optical and scanning electron microscopy. The application of CLPC coated fibers led to a significant improvement in composite strength and young's modulus compared to identical reference samples with uncoated carbon fibers.     

Effects of 1600 °C annealing atmosphere on the microstructures and mechanical properties of C/SiC composites fabricated by precursor infiltration and pyrolysis

Effects of 1600 °C annealing atmosphere on microstructures and mechanical properties of the C/SiC composites fabricated by PIP route were remarkable. Due to carbothermic reductions, the ratios of weight loss of the C/SiC composites were all above 7 wt% in 1 h. Consequently, the mechanical properties all had a significant drop during the first hour of annealing because of the bonding between the fibers and matrix remarkably weaken by cracks and pores. And then the flexural strengths gradually decreased with the annealing time increasing, when the flexural moduli slightly changed within the range of 44.2–49.7 GPa. However, the fracture behaviors of the C/SiC composites annealed under Ar faster became brittle than the C/SiC composites annealed under vacuum. The C/SiC composites annealed under Ar for 5 h and under vacuum for 10 h both became brittle mainly due to the sensitive to annealing of the weak carbon interphase, while the C/SiC composites annealed under Ar for 7 h became brittle mainly due to the chemical bonding between the fibers and matrix. And these phenomena were confirmed by the post densification and the stress-releasing annealing.     

Wear behavior of SiC nanowire-reinforced SiC coating for C/C composites at elevated temperatures

To improve the wear resistance of SiC coating on carbon/carbon (C/C) composites, SiC nanowires (SiCNWs) were introduced into the SiC wear resistant coating. The dense SiC nanowire-reinforced SiC coating (SiCNW-SiC coating) was prepared on C/C composites using a two-step method consisting of chemical vapor deposition and pack cementation. The incorporation of SiCNWs improved the fracture toughness of SiC coating, which is an advantage in wear resistance. Wear behavior of the as-prepared coatings was investigated at elevated temperatures. The results show that the wear resistance of SiCNW-SiC coating was improved significantly by introducing SiC nanowires. It is worth noting that the wear rate of SiCNW-SiC coating was an order of magnitude lower than that of the SiC coating without SiCNWs at 800 °C. The wear mechanisms of SiCNW-SiC coating at 800 °C were abrasive wear and delamination. Pullout and breakage of SiC grains resulted in failure of SiC coating without SiCNWs at 800 °C.     

Fabrication of Cf/ZrC–SiC composites using Zr–8.8Si alloy by melt infiltration

Cf/ZrC–SiC composites were fabricated by melt infiltration at 1800 °C using Zr–8.8Si alloy and carbon felt preforms. Microstructural analysis showed the formation of both ZrC and SiC phases in the matrix, in which ZrC acted as a main composition of the resulting composites. The results showed that carbon matrix reacted preferentially with Si of Zr–8.8Si alloy, which caused the formation of SiC first and then ZrC. The designed carbon coating by pyrolysis prevented the severe reaction between fibers and the melt. The composites could be more dense and uniform with the bending strength of 53.3 MPa, when preforms had a high open porosity (47.2%) with small size pores (10–40 μm).     

Oxidation resistance of SiC/SiC composites containing SiBC matrix fabricated by liquid silicon infiltration

The mechanical behavior and oxidation resistance of SiC/SiC-SiBC composites were studied in this work. According to the debonding criterion of He and Hutchinson, the debonding could occur at the BN interphase, which insures that the fibers can well play the strengthening and toughening performance. The oxidation resistance of SiC/SiC-SiBC composites consisting of SiC fibers with thermal expansion coefficients (CTE) of 5.1 × 10^?6 K^?1 and 4.0 × 10^?6 K^?1 was compared. The composites consisting of SiC fibers with higher CTE show slight weight changes at 800, 1000, and 1200 °C, and the corresponding strength retention ratios are 109.6%, 103.2% and 102.9%, exhibiting excellent oxidation resistance. The CTE of composites consisting of SiC fibers with higher CTE matches well with the CTE of SiC coating, so rarely no cracks can be formed in the coating, which inhibits the inward diffusion of oxidizing medium and leads to high strength retention ratios after oxidation tests.     

Microstructure and properties of 2D-Cf/SiC composite fabricated by combination of CVI and PIP process with SiC particle as inert fillers

2D-C_f/SiC composite was manufactured by chemical vapor inflation (CVI) combined with polymer impregnation and pyrolysis (PIP) with SiC particle as inert fillers. The effects of CVI processes on SiC morphologies and the properties of composite were investigated. The composites were characterized by XRD, flexural strength test and SEM. The results revealed that uniform SiC coatings and nanowires were prepared when MTS/H₂ ratio of 1:8 was employed, while gradient thick coatings were fabricated as MTS/H₂ ratio of 1:1 was employed. The flexural strength of composites varied from 156 MPa at MTS/H₂ ratio of 1:1 to 233 MPa at MTS/H₂ ratio of 1:8. All of composites exhibited toughness due to significant debonding and pullout of fibers. The laminated structure of coatings on the fibers and nanowires were manufactured by combination of above different CVI process, and the obtained composites showed flexural strength of as high as 248 MPa and impressive toughness.     

A mullite/SiC oxidation protective coating for carbon/carbon composites

To protect carbon/carbon (C/C) composites against oxidation, a mullite coating was prepared on SiC precoated C/C composites by a hydrothermal electrophoretic deposition process. The phase composition, microstructure and oxidation resistance of the prepared mullite/SiC coatings were investigated. Results show that hydrothermal electrophoretic deposition is an effective route to achieve crack-free mullite coatings. The mullite/SiC coating displays excellent oxidation resistance and can protect C/C composites from oxidation at 1773 K for 322 h with a weight loss rate of only 4.89 × 10^?4 g/cm² h. The failure of the multi-layer coatings is considered to be caused by the volatilization of silicate glass layer, the formation of microholes and microcracks on the coating surface and the formation of penetrative holes between the SiC bonding layer and the C/C matrix at 1773 K. The corresponding high temperature oxidation activation energy of the coated C/C composites at 1573–1773 K is calculated to be 111.11 kJ/mol.     

Microstructure and oxidation resistance of C-AlPO4–mullite coating prepared by hydrothermal electrophoretic deposition for SiC-C/C composites

Oxidation resistant C-AlPO₄–mullite coating for SiC pre-coated carbon/carbon composites (SiC-C/C) was prepared by a novel hydrothermal electrophoretic deposition process. The phase composition, surface and cross-section microstructure of the as-prepared multi-layer coatings were characterized by X-ray Diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The influence of deposition voltage on phase composition, microstructure and oxidation resistance of the as-prepared coatings was particularly investigated. Results show that the outer layer coating mainly composed of C-AlPO₄ and mullite phase can be achieved after the hydrothermal electrophoretic deposition. The thickness, density and anti-oxidation property of the C-AlPO₄–mullite coating was improved with the increase of deposition voltage from 160 V to 200 V. The multi-layer coating prepared at a voltage of 200 V exhibit excellent anti-oxidation property, which can effectively protect C/C composites from oxidation in air at 1773 K for 324 h with a weight loss of 1.01%. The failure of the multi-layer coatings is due to the generation of cross-holes in the coating, which cannot be self-cured by the metaphosphate and silicate glass layer after long time oxidation at 1773 K.     

Effect of PyC interphase thickness on mechanical behaviors of SiBC matrix modified C/SiC composites fabricated by reactive melt infiltration

A dense carbon fiber reinforced silicon carbide matrix composites modified by SiBC matrix (C/SiC-SiBC) was prepared by a joint process of chemical vapor infiltration, slurry infiltration and liquid silicon infiltration. The effects of pyrolytic carbon (PyC) interphase thickness on mechanical properties and oxidation behaviors of C/SiC-SiBC composites were evaluated. The results showed that C/SiC-SiBC composites with an optimal PyC interphase thickness of 450 nm exhibited flexural strength of 412 MPa and fracture toughness of 24 MPa m^1/2, which obtained 235% and 300% improvement compared with the one with 50 nm-thick PyC interphase. The enhanced mechanical properties of C/SiC-SiBC composites with the increase of interphase thickness was due to the weakened interfacial bonding strength and the decrease of matrix micro-crack amount associated with the reduction of thermal residual stress. With the decrease in matrix porosity and micro-crack density, C/SiC-SiBC composites with 450 nm-thick interphase exhibited excellent oxidation resistance. The residual flexural strength after oxidized at 800, 1000 and 1200 °C in air for 10 h was 490, 500 and 480 MPa, which increased by 206%, 130% and 108% compared with those of C/SiC composites.     

Effects of porous C/C density on the densification behavior and ablation property of C/C–ZrC–SiC composites

C/C–ZrC–SiC composites were prepared by precursor infiltration and pyrolysis process using a mixture solution of organic zirconium-containing polymer and polycarbosilane as precursors. Porous carbon/carbon (C/C) composites with density of 0.92, 1.21 and 1.40 g/cm³ were used as preforms, and the effects of porous C/C density on the densification behavior and ablation resistance of C/C–ZrC–SiC composites were investigated. The results show that the C/C preforms with a lower density have a faster weight gain, and the obtained C/C–ZrC–SiC composites own higher bulk density and open porosity. The composites fabricated from the C/C preforms with a density of 1.21 g/cm³ exhibit better ablation resistance with a surface temperature of over 2400 °C during ablation. After ablation for 120 s, the linear and mass ablation rates of the composites are as low as 1.02 × 10⁻³ mm/s and −4.01 × 10⁻⁴ g/s, respectively, and the formation of a dense and continuous coating of molten ZrO₂ solid solution is the reason for their great ablation resistance.     

Analysis of instrumented scratch hardness and fracture toughness properties of laser surface alloyed tribological coatings

The mechanical characteristics of ceramic matrix composite (CMC) coatings are widely different from the same materials in bulk form or the individual constituents and are very important to be assessed to carry out application oriented studies on CMC coatings with novel compositions. In the present work, a composite coating of TiB₂, TiN and SiC is fabricated in-situ through a combination of high temperature chemical reaction and laser surface alloying. The formation of the surface layer is due to the laser-assisted chemical reaction followed by laser melting. A mixture of TiO₂, SiO₂, hBN and graphite in stoichiometric proportions is used as the precursor for the chemical reaction. The presence of all the reaction products in the CMC coatings developed is confirmed by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). A thorough evaluation of various mechanical properties achieved more insight into the CMC coatings developed. Hardness and fracture toughness of the coatings are measured with a scratch tester. The property evaluations are performed in a similar way for two more coatings fabricated with precursor mixtures containing more than a stoichiometric amount of SiC and hBN respectively. For comparison, a number of composites fabricated through various other routes are characterized afresh with the same set of techniques. Coatings formed with SiC in precursor show higher values of scratch hardness (14.37 GPa), microhardness (24.37 GPa) and fracture toughness (6.63 MPa-m^1/2).     

Mechanical and dielectric properties of SiCf/SiC composites fabricated by PIP combined with CIP process

2D KD-1 SiC fiber fabrics were employed to fabricate SiC_f/SiC composites by an improved polymer infiltration and pyrolysis (PIP) process, combined with cold isostatic pressing (CIP). The effect of CIP process on the microstructure, mechanical and dielectric properties of SiC_f/SiC composites was investigated. The infiltration efficiency was remarkably improved with the introduction of CIP process. Compared to vacuum infiltration, the CIP process can effectively increase the infiltrated precursor content and decrease the porosity resulting in a dense matrix. Thus SiC_f/SiC composites with high density of 2.11 g cm⁻³ and low porosity of 11.3% were obtained at 100 MPa CIP pressure, together with an increase of the flexural strength of the composites from 89 MPa to 213 MPa. Real part (ε′) and the imaginary part (ε″) of complex permittivity of SiC_f/SiC composites increase and vary from 11.7-i9.7 to 15.0-i12.8 when the CIP pressure reaches 100 MPa.     

Ablation resistance of HfB2-SiC coating prepared by in-situ reaction method for SiC coated C/C composites

To improve the ablation resistance of SiC coating, HfB₂-SiC coating was prepared on SiC-coated carbon/carbon (C/C) composites by in-situ reaction method. Owing to the penetration of coating powders, there is no clear boundary between SiC coating and HfB₂-SiC coating. After oxyacetylene ablation for 60 s at heat flux of 2400 kW/m², the mass ablation rate and linear ablation rate of the coated C/C composites were only 0.147 mg/s and 0.267 µm/s, reduced by 21.8% and 60.0%, respectively, compared with SiC coated C/C composites. The good ablation resistance was attributed to the formation of multiple Hf-Si-O glassy layer including SiO₂, HfO₂ and HfSiO₄.