SnO2 nano-spheres/graphene hybrid for high-performance lithium ion battery anodes

SnO₂ nano-spheres/graphene composite was fabricated via a simple one-step hydrothermal method with graphene oxide and SnCl₄·5H₂O as the precursors. The composite was characterized by X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy and surface area measurement. It is shown that fine SnO₂ nano-spheres with an average size of 50–100 nm could be homogeneously deposited on graphene nano-sheets layer by layer. The structural feature enabled SnO₂ nano-spheres/graphene hybird as an excellent anode material in lithium ion battery. The composite possesses 1306 mA h g^?1 of initial discharge capacity and good capacity retention of 594 mA h g^?1 up to the 50th cycle at a current density of 100 mA g^?1. These results indicate that the composite is a promising anode material in high-performance lithium ion batteries.     

Ultrafine SnO2 nanoparticles as a high performance anode material for lithium ion battery

In this paper, the ultrafine tin oxides (SnO₂) nanoparticles are fabricated by a facile microwave hydrothermal method with the mean size of only 14 nm. Phase compositions and microstructures of the as-prepared nanoparticles have been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that the ultrafine SnO₂ nanoparticles are obtained to be the pure rutile-structural phase with the good dispersibility. Galvanostatic cycling and cyclic voltammetry results indicate that the first discharge capacity of the ultrafine SnO₂ electrode is 1196.63  mAh g⁻¹, and the reversible capacity could retain 272.63 mAh g⁻¹ at 100 mA g⁻¹ after 50 cycles for lithium ion batteries (LIBs). The excellent electrochemical performance of the SnO₂ anode for LIBs is attributed to its ultrafine nanostructure for providing active sites during lithium insertion/extraction processes. Pulverization and agglomeration of the active materials are effectively reduced by the microwave hydrothermal method.     

Nanocomposites of SnO2 and g-C3N4: Preparation,characterization and photocatalysis under visible LED irradiation

Tin dioxide nanoparticles were prepared in the presence of graphitized carbon nitride (g-C₃N₄) forming nanocomposites with different contents of SnO₂ up to 40 %. G-C₃N₄ was synthetized by heating of melamine at 550 °C in the open air and Sn²⁺ ions were precipitated by sodium hydroxide in g-C₃N₄ aqueous dispersions. Resulting mixtures were dried by freezing at ?20 °C and calcined at 450 °C to obtain SnO₂/g-C₃N₄ nanocomposites.The nanocomposites were characterized by common characterization methods in solid state and in their aqueous dispersions using dynamic light scattering (DLS) analysis and photocatalysis. SnO₂ nanoparticles in the nanocomposites were found to have an average size of 4 nm, however, those precipitated without g-C₃N₄ had an average size of 14 nm. Separation of photoinduced electron and holes via heterojunction between SnO₂ and g-C₃N₄ was demonstrated by photocatalytic decomposition of Rhodamine B (RhB) under LED visible irradiation (416 nm) and photocurrent measurements. The most photocatalytically active nanocomposite contained 10 % of SnO₂. Graphitized carbon nitride was assumed to serve as a template structure for the preparation of SnO₂ nanoparticles with a narrow size distribution without using any stabilizing additives.     

Controlled synthesis of Fe3O4@SnO2/RGO nanocomposite for microwave absorption enhancement

A ternary nanocomposite of Fe₃O₄@SnO₂/reduced graphene oxide (RGO) with different contents of SnO₂ nanoparticles was synthesized by a simple and efficient three-step method. The transmission electron microscopy and field emission scanning electron microscopy characterization display that plenty of Fe₃O₄@SnO₂ core–shell structure nanoparticles are well distributed on the surface of RGO sheets. The X-ray diffractograms show that the products consist of highly crystallized cubic Fe₃O₄, tetragonal SnO₂ and disorderedly stacked RGO sheets. The magnetic hysteresis measurement reveals the ferromagnetic behavior of the products at room temperature. The microwave absorption properties of paraffin containing 50 wt% products were investigated at room temperature in the frequency range of 2–18 GHz by a vector network analyzer. The electromagnetic data show that the maximum reflection loss is −45.5 dB and −29.5 dB for Fe₃O₄@SnO₂/RGO-1 and Fe₃O₄@SnO₂/RGO-2 nanocomposite, respectively. Meanwhile, the reflection loss less than −10 dB is up to 14.4 GHz and 13.8 GHz for Fe₃O₄@SnO₂/RGO-1 and Fe₃O₄@SnO₂/RGO-2 nanocomposite, respectively. It is believed that such nanocomposite could be used as promising microwave absorbers.     

Preparation and electrochemical performance of SnO2@carbon nanotube core–shell structure composites as anode material for lithium-ion batteries

Carbon nanotube-encapsulated SnO₂ (SnO₂@CNT) core–shell composite anode materials are prepared by chemical activation of carbon nanotubes (CNTs) and wet chemical filling. The results of X-ray diffraction and transmission electron microscopy measurements indicate that SnO₂ is filled into the interior hollow core of CNTs and exists as small nanoparticles with diameter of about 6 nm. The SnO₂@CNT composites exhibit enhanced electrochemical performance at various current densities when used as the anode material for lithium-ion batteries. At 0.2 mA cm^?2 (0.1C), the sample containing wt. 65% of SnO₂ displays a reversible specific capacity of 829.5 mAh g^?1 and maintains 627.8 mAh g^?1 after 50 cycles. When the current density is 1.0, 2.0, and 4.0 mA cm^?2 (about 0.5, 1.0, and 2.0C), the composite electrode still exhibits capacity retention of 563, 507 and 380 mAh g^?1, respectively. The capacity retention of our SnO₂@CNT composites is much higher than previously reported values for a SnO₂/CNT composite with the same filling yield. The excellent lithium storage and rate capacity performance of SnO₂@CNT core–shell composites make it a promising anode material for lithium-ion batteries.     

Highly sensitive acetone sensor based on Eu-doped SnO2 electrospun nanofibers

In this study, a series of undoped and Eu-doped SnO₂ nanofibers were synthesized via a simple electrospinning technique and subsequent calcination treatment. Field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were carefully used to characterize the morphologies, structures and chemical compositions of these samples. The results reveal that the as-prepared nanofibers are composed of crystallite grains with an average size of about 10 nm and Eu³⁺ ions are successfully doped into the SnO₂ lattice. Compared with pure SnO₂ nanofibers, Eu-doped SnO₂ nanofibers demonstrate significantly enhanced sensing characteristics (e.g., large response value, short response/recovery time and outstanding selectivity) toward acetone vapor, especially, the optimal sensor based on 2 mol% Eu-doped SnO₂ nanofibers shows the highest response (32.2 for 100 ppm), which is two times higher than that of the pure SnO₂ sensor at an operating temperature of 280 °C. In addition, the sensor exhibits a good sensitivity to acetone in sub-ppm concentrations and the detection limit could extend down to 0.3 ppm, making it a potential candidate for the breath diagnosis of diabetes.     

Design and synthesis of three-dimensional needle-like CoNi2S4/CNT/graphene nanocomposite with improved electrochemical properties

In this paper, we described a simple two–step method for preparing needle-like CoNi₂S₄/CNT/graphene nanocomposite with robust connection among its ternary components. The prepared CoNi₂S₄/CNT/graphene nanocomposite has been thoroughly characterized by spectroscopic (Fourier-transform infrared spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy), X-ray diffraction and thermogravimetric analysis. Microscopy techniques (scanning electron microscopy–energy dispersive spectroscopy and transmission electron microscopy) were employed to probe the morphological structures. The electrochemical properties of the as-prepared 3D architectures were investigated with three and two-electrode systems. In addition to its high specific capacitance (710 F g⁻¹ at 20 A g⁻¹), after charging–discharging for 2000 cycles, the electrode still maintained the capacity retention of about 82%. When used as the active electrode material for supercapacitors, the fabricated CoNi₂S₄–g–CNT nanostructure exhibited excellent specific capacitance and good rate capability, making it a promising candidate for next-generation supercapacitors.     

Synthesis of cross-linked graphene aerogel/Fe2O3 nanocomposite with enhanced supercapacitive performance

In this work, cross-linked graphene aerogel (CL-GA) and its composite with Fe₂O₃ nanoparticles (NPs) were synthesized through a one-step hydrothermal procedure by using p-phenylenediamine (PPD). Structural characterizations revealed that in the preparation of the composite PPD acts as a cross-liker and provides high surface area by decreasing restacking of graphene sheets and functions as nitrogen source simultaneously. The electrochemical characteristics of the nanocomposite were investigated by cyclic voltammetry (CV), galvanostatic charge/discharge, electrochemical impedance spectroscopy (EIS) and Fast Fourier transform continues cyclic voltammetry (FFTCCV). The results show that cross-linked graphene aerogel/Fe₂O₃ (CL-GA/Fe₂O₃) nanocomposite displays enhanced supercapacitive performance, where it has capacitance of 445 at 1 A g⁻¹, high energy density of 63 W h Kg⁻¹, and 89% capacitance retention after 5000 cycles in 3 M KOH. Presence of PPD considerably improved supercapacitive performance of nanocomposite as a result it could be promising material in synthesis of efficient graphene/metal oxide-based electrode material for high performance supercapacitors.     

Process intensification of uniform loading of SnO2 nanoparticles on graphene oxide nanosheets using a novel ultrasound assisted in situ chemical precipitation method

In this paper, a novel ultrasound assisted, solution-based chemical synthesis method for the preparation of SnO₂–graphene nanocomposite is presented. Graphene oxide (GO) was prepared by the modified Hummers–Offeman method in presence of ultrasonic irradiation. Further loading of SnO₂ on GO was carried out with an ultrasound assisted solution-based synthesis route. The prepared GO and SnO₂–graphene nanocomposite were characterized by XRD, TEM, FTIR spectra, TGA and DTA analysis in order to confirm the formation of graphene–SnO₂ nanocomposite. TEM analysis of ultrasonically prepared graphene–SnO₂ composite shows the uniform and fine loading of SnO₂ particles (3–5 nm) on graphene nanosheets. However agglomerated morphology was observed in case of conventionally prepared graphene–SnO₂ composite. The cavitational effects generated due to the ultrasonic irradiations during the synthesis of graphene–SnO₂ composite improve the fine and uniform loading of SnO₂ on graphene nanosheets by oxidation–reduction reaction between GO and SnCl₂·2H₂O compared to conventional synthesis methods. The formed material was used for the preparation of anode in lithium ion batteries and its electrochemical performance was characterized by cyclic voltammetry and charge/discharge cycles. It is found that the capacity of SnO₂–graphene nanocomposite based Li-battery is stable for around 120 cycles, and the battery could repeat stable charge–discharge reaction.     

Carbon-coated SnO2/graphene nanosheets as highly reversible anode materials for lithium ion batteries

A simple approach is reported to prepare carbon-coated SnO₂ nanoparticle–graphene nanosheets (Gr–SnO₂–C) as an anode material for lithium ion batteries. The material exhibits excellent electrochemical performance with high capacity and good cycling stability (757 mA h g^?1 after 150 cycles at 200 mA g^?1). The likely contributing factors to the outstanding charge/discharge performance of Gr–SnO₂–C could be related to the synergism between the excellent conductivity and large area of graphene, the nanosized particles of SnO₂, and the effects of the coating layer of carbon, which could alleviate the effects of volume changes, keep the structure stable, and increase the conductivity. This work suggests a strategy to prepare carbon-coated graphene–metal oxide which could be used to improve the electrochemical performance of lithium ion batteries.     

In situ sonochemical synthesis of Fe3O4–graphene nanocomposite for lithium rechargeable batteries

In this paper, we have presented experimental results for preparation of Fe₃O₄–graphene nanocomposite that uses an ultrasound assisted method. The graphene oxide (GO) was prepared from graphite powder using modified Hummers–Offeman method. Subsequently, the synthesis of graphene-Fe₃O₄ nanocomposite was carried out by ultrasound assisted co-precipitation of iron (II) and (III) chlorides in the presence of GO. The formation of GO and graphene-Fe₃O₄ nanocomposite was confirmed by X-ray diffraction (XRD), Energy dispersive X-ray (EDX) analysis and Fourier transform-infrared (FTIR) analysis. The particle size of Fe₃O₄ nanoparticles loaded on graphene nanosheets (observed from TEM image) was found to be smaller than 20 nm. The use of ultrasonic irradiations during synthesis of graphene-Fe₃O₄ nanocomposite resulted in uniform loading of Fe₃O₄ nanoparticles on graphene nanosheets. The prepared graphene-Fe₃O₄ nanocomposite material was used for the preparation of anode for lithium ion batteries. The electrochemical performance of the material was tested by cyclic voltammetry (CV) and charge/discharge cycles. It was observed that the capacity of Li-battery when the anode material was made using graphene-Fe₃O₄ nanocomposite showed stable electrochemical performance for around 120 cycles and the battery could repeat stable charge–discharge reaction.     

Raman spectra,photoluminescence and ferromagnetism of pure,Co and Fe doped SnO2 nanoparticles

The pure and transition metal (Co and Fe = 3 and 5 mol%) doped SnO₂ nanoparticles have been synthesized by a chemical route using polyvinyl alcohol as surfactant. These nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Raman, Fourier transform infrared (FTIR) spectroscopy, photoluminescence (PL) and magnetic measurements. The XRD patterns show that all the samples have tetragonal rutile structure without any extra phase and the value of average particle size using FWHM lies within 12–29 nm is also confirmed by TEM. FTIR spectrum has been used to confirm the formation of SnO bond. Raman spectroscopy shows the intensity loss of classical cassiterite SnO₂ vibration lines which is an indication of significant structural modifications. From PL, an intense blue luminescence centered at a wavelength ～530 nm is observed in the prepared SnO₂ nanoparticles, which is different from the yellow-red light emission observed in SnO₂ nanostructures prepared by other methods. The strong blue luminescence from the as-grown SnO₂ nanoparticles is attributed to oxygen-related defects that have been introduced during the growth process. These Co and Fe-doped SnO₂ nanoparticles exhibit room temperature ferromagnetism and the value of their magnetic moment and phase transition temperature are sensitive to their size and stoichiometric ratio.     

High reversible capacity of SnO2/graphene nanocomposite as an anode material for lithium-ion batteries

A gas–liquid interfacial synthesis approach has been developed to prepare SnO₂/graphene nanocomposite. The as-prepared nanocomposite was characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and Brunauer–Emmett–Teller measurements. Field emission scanning electron microscopy and transmission electron microscopy observation revealed the homogeneous distribution of SnO₂ nanoparticles (2–6 nm in size) on graphene matrix. The electrochemical performances were evaluated by using coin-type cells versus metallic lithium. The SnO₂/graphene nanocomposite prepared by the gas–liquid interface reaction exhibits a high reversible specific capacity of 1304 mAh g⁻¹ at a current density of 100 mA g⁻¹ and excellent rate capability, even at a high current density of 1000 mA g⁻¹, the reversible capacity was still as high as 748 mAh g⁻¹. The electrochemical test results show that the SnO₂/graphene nanocomposite prepared by the gas–liquid interfacial synthesis approach is a promising anode material for lithium-ion batteries.     

Polyaniline (PANI)–Co0.5Mn0.5Fe2O4 nanocomposite: Synthesis,characterization and magnetic properties evaluation

Polyaniline (PANI)/Cobalt-manganese ferrite, (PANI)/Co_0.5Mn_0.5Fe₂O₄, nanocomposite was synthesized by oxidative chemical polymerization of aniline in the presence of ammonium peroxydisulfate (APS). Microwave assisted synthesis method was used for the fabrication of core CoFe₂O₄ nanoparticles. The structural, morphological, thermal and magnetic properties of the nanocomposite were investigated in detail by X-ray diffraction (XRD), fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). The average crystallite size of (PANI)/Co_0.5Mn_0.5Fe₂O₄ nanocomposite by the line profile method was 20±9 nm. The magnetization measurements revealed that (PANI)/Co_0.5Mn_0.5Fe₂O₄ nanocomposite has superparamagnetic behavior with blocking temperature higher than 300 K. The saturation magnetization of the composite is considerably low compared to that of CoFe₂O₄ nanoparticles due to the partial replacement of Co²⁺ ions and surface spin disorder. As temperature decreases, both coercivity and strength of antiferromagnetic interactions increase which results in unsaturated magnetization of the nanocomposite.     

Surfactant-free microwave hydrothermal synthesis of SnO2 nanosheets as an anode material for lithium battery applications

SnO₂ nanosheets were synthesized using microwave hydrothermal method without using a surfactant and organic solvents. Formation of pure nanocrystalline rutile phase of SnO₂ sample was confirmed by X-ray diffraction (XRD) results and the average crystallite size of SnO₂ sample calculated using Scherrer's formula and XRD data is found to be 6 nm. HR-TEM, SAED and EDX results showed the formation of agglomerated nanosize sheets like morphology with high porous structured SnO₂ powder. Further, the formation of high porous structured SnO₂ powder was confirmed from BET surface area results (59.28 m² g^?1). The electrochemical performance of the lithium-ion battery made up of SnO₂ nanosheets, as an anode, was tested through the cyclic voltammetry and galvanostatic charge-discharge measurements. The galvanostatic charge-discharge results of the lithium-ion battery showed good discharge capacity of 257.8 mAh g^?1 after 50 cycles at a current density of 100 mA g^?1. The improved electrochemical properties may be due to the formation of a unique nanosize sheets type morphology with high porous structured SnO₂ powder. High porous structured nanosize sheets type morphology of SnO₂ can help to reduce the diffusion length and sustain the volume changes during the charging-discharging process.Hence, high porous structured nanosize sheets morphology of SnO₂ prepared using the microwave hydrothermal method without using a surfactant and organic solvents can be a better anode material for lithium ion battery applications.     

Electrochemical energy storage performance of heterostructured SnO2@MnO2 nanoflakes

In this work, we report synthesis of SnO₂@MnO₂ nanoflakes grown on nickel foam through a facile two-step hydrothermal route. The as-obtained products are characterized by series of techniques such as scanning electron microscopy (SEM), X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The as-obtained SnO₂@MnO₂ nanoflakes are directly used as supercapacitor electrode materials. The results show that the electrode possesses a high discharge areal capacitance of 1231.6 mF cm⁻² at 1 mA cm⁻² and benign cycling stability with 67.2% of initial areal capacitance retention when the current density is 10 mA cm⁻² after 6000 cycles. Moreover, the heterostructured electrode shows 41.1% retention of the initial capacitance when the current densities change from 1 to 10 mA cm⁻², which reveals good rate capability. SnO₂@MnO₂ nanoflakes products which possess excellent electrochemical properties might be used as potential electrode materials for supercapacitor applications.     

Simple self-assembly of SnS2 entrapped graphene aerogel and its enhanced lithium storage performance

In this work, SnS₂ nanoplates entrapped graphene aerogel has been successfully prepared by simple self-assembly of reduced graphene oxide obtained through mild chemical reduction. Structural and morphological investigations demonstrated that SnS₂ nanoplates are highly dispersed in the three dimensional (3D) porous graphene matrix. When served as anode material for lithium-ion batteries, the electrochemical properties of SnS₂/graphene aerogel (SnS₂/GA) were evaluated by galvanostatic discharge–charge tests, cyclic voltammetry and impedance spectroscopy measurement. Compared with pristine SnS₂, the SnS₂/GA nanocomposite achieved a much higher initial reversible capacity (1186 mAh g⁻¹), superior cyclic stability (1004 mAh g⁻¹ after 60 cycles, corresponding to 84.7% of the initial reversible capacity), as well as better rate capability (650 mAh g⁻¹ at a current density of 1000 mA g⁻¹). This significantly improved lithium storage performance can be attributed to the good integration of SnS₂ nanoplates with 3D porous graphene network, which can not only provide much more active sites and easy access for Li ions intercalation, but also prevent the aggregation of SnS₂ nanoplates and facilitate fast transportation of Li ions and surface electrons during the electrochemical process.     

Preparation of meso-porous SnO2 fibers with enhanced sensitivity for n-butanol

Meso-porous SnO₂ fibers were synthesized using a solvothermal method with metaplexis fruit as the bio-template. The products were characterized by powder X-ray diffraction, high resolution scanning electron microscopy, transmission electron microscopy and nitrogen adsorption/desorption measurements. Results show that SnO₂ fibers present a high specific surface area of 73.665 m²/g and a meso-porous structure with the pore size of 7.821 nm, and the crystal size of SnO₂ is about 6.5 ± 0.5 nm. The gas sensing performance of the prepared SnO₂ fibers toward several volatile organic compounds was investigated. The results show that the meso-porous SnO₂ fibers were highly sensitive and selective to n-butanol.     

Reduced graphene oxide anchored with δ-MnO2 nanoscrolls as anode materials for enhanced Li-ion storage

We developed a one-pot in situ synthesis procedure to form nanocomposite of reduced graphene oxide (RGO) sheets anchored with 1D δ-MnO₂ nanoscrolls for Li-ion batteries. The as-prepared products were characterized by X-ray diffraction (XRD), Raman spectra, X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscope (FESEM) and transmission electron microscope (TEM). The electrochemical performance of the δ-MnO₂ nanoscrolls/RGO composite was measured by galvanostatic charge/discharge cycling and electrochemical impedance spectroscopy. The results show that the δ-MnO₂ nanoscrolls/RGO composite displays superior Li-ion battery performance with large reversible capacity and high rate capability. The first discharge and charge capacities are 1520 and 810 mAh g⁻¹, respectively. After 50 cycles, the reversible discharge capacity is still maintained at 528 mAh g⁻¹ at the current density of 100 mAh g⁻¹. The excellent electrochemical performance is attributed to the unique nanostructure of the δ-MnO₂ nanoscrolls/RGO composite, the high capacity of MnO₂ and superior electrical conductivity of RGO.     

Stability and thermal conductivity of nanofluids of tin dioxide synthesized via microwave-induced combustion route

SnO₂ nanofluids were prepared by dispersing tin dioxide nanoparticles in deionized (DI) water as a base fluid. 4–5 nm tin dioxide crystals were synthesized via chloride solution combustion synthesis (CSCS) using SnCl₄ and sorbitol as a novel precursor and the fuel, respectively. Ammonium nitrate was also used as the combustion aid. The molar ratio of sorbitol plus ammonium nitrate to SnCl₄ was set at unity; whereas, the molar ratio of sorbitol-to-ammonium nitrate divided by that of stoichiometric value (Φ) was varied in the range of 0.5–1.4 in order to find the optimum values of specific surface area for the CSCS technique. Transition electron microscopy (TEM), scanning electron microscopy (SEM), powder X-ray diffraction (XRD), and Brunauer–Emmet–Teller (BET) techniques were employed for the characterization of the nanoparticles. Since SnO₂ nanoparticles form clusters within fluids, the fluids were ultrasonicated to improve the dispersion and stability of the nanoparticles. The colloidal stability of the SnO₂ nanofluids was quantitatively characterized by UV–vis spectrophotometric measurements. The results of the UV–vis experiments indicate higher dispersion together with enhanced stability for the nanofluid prepared by SnO₂ nanoparticles synthesized at Φ = 1.0. After 500 h sedimentation time, the relative concentration of the nanofluid with the highest stability is remained at around 77% of the initial concentration of the fluid.A transient hot-wire apparatus was used to measure the thermal conductivities of the nanofluids. In addition, the effects of pH and temperature on the thermal conductivity were also investigated. At 353 K, for the nanofluid prepared by SnO₂ nanoparticles synthesized at Φ = 1.0 at a weight fraction of 0.024%, thermal conductivity is enhanced up to about 8.7%, with an optimal pH = 8.