Li4Ti5O12/Sn composite anodes for lithium-ion batteries: Synthesis and electrochemical performance

Li₄Ti₅O₁₂/tin phase composites are successfully prepared by cellulose-assisted combustion synthesis of Li₄Ti₅O₁₂ matrix and precipitation of the tin phase. The effect of firing temperature on the particulate morphologies, particle size, specific surface area and electrochemical performance of Li₄Ti₅O₁₂/tin oxide composites is systematically investigated by SEM, XRD, TG, BET and charge-discharge characterizations. The grain growth of tin phase is suppressed by forming composite with Li₄Ti₅O₁₂ at a calcination of 500 °C, due to the steric effect of Li₄Ti₅O₁₂ and chemical interaction between Li₄Ti₅O₁₂ and tin oxide. The experimental results indicate that Li₄Ti₅O₁₂/tin phase composite fired at 500 °C has the best electrochemical performance. A capacity of 224 mAh g⁻¹ is maintained after 50 cycles at 100 mA g⁻¹ current density, which is still higher than 195 mAh g⁻¹ for the pure Li₄Ti₅O₁₂ after the same charge/discharge cycles. It suggests Li₄Ti₅O₁₂/tin phase composite may be a potential anode of lithium-ion batteries through optimizing the synthesis process.     

Fe3O4 submicron spheroids as anode materials for lithium-ion batteries with stable and high electrochemical performance

A magnetite (Fe₃O₄) powder composed of uniform sub-micrometer spherical particles has been successfully synthesized by a hydrothermal method at low temperature. X-ray diffraction, scanning electron microscopy, transmission electron microscopy and galvanostatic cell cycling are employed to characterize the structure and electrochemical performance of the as-prepared Fe₃O₄ spheroids. The magnetite shows a stable and reversible capacity of over 900 mAh g⁻¹ during up to 60 cycles and good rate capability. The experimental results suggest that the Fe₃O₄ synthesized by this method is a promising anode material for high energy-density lithium-ion batteries.     

Li3V2(PO4)3/C composite as an intercalation-type anode material for lithium-ion batteries

The carbon coated monoclinic Li₃V₂(PO₄)₃ (LVP/C) powder is successfully synthesized by a carbothermal reduction method using crystal sugar as the carbon source. Its structure and physicochemical properties are investigated using X-ray diffraction (XRD), scanning electron microscopy, high-resolution transmission electron microscopy and electrochemical methods. The LVP/C electrode exhibits stable reversible capacities of 203 and 102 mAh g⁻¹ in the potential ranges of 3.0-0.0 V and 3.0-1.0 V versus Li⁺/Li, respectively. It is identified that the insertion/extraction of Li⁺ undergoes a series of two-phase transition processes between 3.0 and 1.6 V and a single phase process between 1.6 and 0.0 V. The ex situ XRD patterns of the electrodes at various lithiated states indicate that the monoclinic structure can still be retained during charge-discharge process and the insertion/deinsertion of lithium ions occur reversibly, which provides an excellent cycling stability with high energy efficiency.     

Electrostatic spray deposition of porous Fe2O3 thin films as anode material with improved electrochemical performance for lithium-ion batteries

Iron oxide materials are attractive anode materials for lithium-ion batteries for their high capacity and low cost compared with graphite and most of other transition metal oxides. Porous carbon-free α-Fe₂O₃ films with two types of pore size distribution were prepared by electrostatic spray deposition, and they were characterized by X-ray diffraction, scanning electron microscopy and X-ray absorption near-edge spectroscopy. The 200 °C-deposited thin film exhibits a high reversible capacity of up to 1080 mAh g⁻¹, while the initial capacity loss is at a remarkable low level (19.8%). Besides, the energy efficiency and energy specific average potential (E_av) of the Fe₂O₃ films during charge/discharge process were also investigated. The results indicate that the porous α-Fe₂O₃ films have significantly higher energy density than Li₄Ti₅O₁₂ while it has a similar E_av of about 1.5 V. Due to the porous structure that can buffer the volume changes during lithium intercalation/de-intercalation, the films exhibit stable cycling performance. As a potential anode material for high performance lithium-ion batteries that can be applied on electric vehicle and energy storage, rate capability and electrochemical performance under high-low temperatures were also investigated.     

Facile synthesis of hierarchically structured Fe3O4/carbon micro-flowers and their application to lithium-ion battery anodes

A flower-like Fe₃O₄/carbon nanocomposite with nano/micro hierarchical structure is prepared by controlled thermal decomposition of the iron alkoxide precursor, which is obtained via an ethylene glycol-mediated solvothermal reaction of FeCl₃ and hexamethylenetetramine (HMT) in the absence of any surfactant. The nanocomposite is characterized by the assembly of porous nanoflakes consisting of Fe₃O₄ nanoparticles and amorphous carbon that is in situ generated from the organic components of alkoxide precursor. When used as the anode materials for the lithium-ion batteries, the resultant nanocomposite shows high capacity and good cycle stability (1030 m Ah g⁻¹ at a current density of 0.2 C up to 150 cycles), as well as enhanced rate capability. The excellent electrochemical performance can be attributed to the high structural stability and high rate of ionic/electronic conduction arising from the synergetic effect of the unique nano/micro hierarchical structure and conductive carbon coating.     

A novel carbon-silicon composite nanofiber prepared via electrospinning as anode material for high energy-density lithium ion batteries

Electrospun carbon-silicon composite nanofiber is employed as anode material for lithium ion batteries. The morphology of composite nanofiber is optimized on the C/Si ratio to make sure well distribution of silicon particles in carbon matrix. The C/Si (77/23, w/w) nanofiber exhibits large reversible capacity up to 1240 mAh g⁻¹ and excellent capacity retention. Ex situ scanning electron microscopy is also conducted to study the morphology change during discharge/charge cycle, and the result reveals that fibrous morphology can effectively prevent the electrode from mechanical failure due to the large volume expansion during lithium insertion in silicon. AC impedance spectroscopy reveals the possible reason of unsatisfactory rate capability of the nanofiber. These results indicate that this novel C/Si composite nanofiber may has some limitations on high power lithium ion batteries, but it can be a very attractive potential anode material for high energy-density lithium-ion batteries.     

Synthesis of Co3O4/Carbon composite nanowires and their electrochemical properties

Porous nanowires of Co₃O₄/Carbon composite have been synthesized by using a simple and inexpensive electrospinning technique. The as-prepared materials were investigated by X-ray diffraction and scanning electron microscopy. The electrochemical properties of the composite have been characterized using cyclic voltammetry and galvanostatic methods. The results show a remarkably improved electrochemical performance in term of reversible capacity, rate capability, and cycling performance.     

One-pot, glycine-assisted combustion synthesis and characterization of nanoporous LiFePO4/C composite cathodes for lithium-ion batteries

Nanoporous LiFePO₄/C composite cathodes have been synthesized by a novel one-pot, glycine-assisted combustion (GAC) method in presence of 2 wt.% Super P carbon in both Ar and 90% Ar-10% H₂ atmospheres at 750 °C for a short time of 6 h. While the Ar atmosphere offers phase pure samples, the Ar-H₂ atmosphere leads to the formation of impurity phases as indicated by X-ray diffraction data. The combustion-initiated expulsion of gases aids the formation of a nanoporous LiFePO₄/C composite structure as evident from electron microscopic analysis, which could allow easy penetration of the electrolyte and realization of an electronic-ionic 3D network. The nanoporous LiFePO₄/C sample synthesized in Ar atmosphere exhibits a high discharge capacity of 160 mAh g⁻¹ with 3% capacity fade in 50 cycles and high rate capability. With a short reaction time, the GAC method offers an energy efficient approach to synthesize high performance olivine LiFePO₄/C composite cathodes.     

V2O3 modified LiFePO4/C composite with improved electrochemical performance

In addition to lattice doping and carbon-coating, surface modification with other metal oxides can also improve the electrochemical performance of LiFePO₄ powders. In this work, highly conductive vanadium oxide (V₂O₃) is in situ produced during the synthesis of carbon-coated LiFePO₄ (LiFePO₄/C) powders by a solid state reaction process and acts as a surface modifier. The structures and compositions of LiFePO₄/C samples containing 0-10 mol% vanadium are analyzed by X-ray diffraction, Raman spectroscopy, scanning electron microscopy and transmission electron microscopy. Their electrochemical properties are also characterized with galvanostatic cell cycling and cyclic voltammetry. It is found that vanadium is present in the form of V₂O₃ that is incorporated in the carbon phase. The vanadium-modified LiFePO₄/C samples show improved rate capability and low-temperature performance. Their apparent lithium diffusion coefficient is in the range of 10⁻¹² to 10⁻¹⁰ cm² s⁻¹ depending on the vanadium content. Among the investigated samples, the one with 5 mol% vanadium exhibits the best electrochemical performance.     

Effects of Fe2P and Li3PO4 additives on the cycling performance of LiFePO4/C composite cathode materials

In this study, a solution method was employed to synthesize LiFePO₄-based powders with Li₃PO₄ and Fe₂P additives. The composition, crystalline structure, and morphology of the synthesized powders were investigated by using ICP-OES, XRD, TEM, and SEM, respectively. The electrochemical properties of the powders were investigated with cyclic voltammetric and capacity retention studies. The capacity retention studies were carried out with LiFePO₄/Li cells and LiFePO₄/MCMB cells comprised LiFePO₄-based materials prepared at various temperatures from a stoichiometric precursor. Among all of the synthesized powders, the samples synthesized at 750 and 775 °C demonstrate the most promising cycling performance with C/10, C/5, C/2, and 1C rates. The sample synthesized at 775 °C shows initial discharge capacity of 155 mAh g⁻¹ at 30 °C with C/10 rate. From the results of the cycling performance of LiFePO₄/MCMB cells, it is found that 800 °C sample exhibited higher polarization growth rate than 700 °C sample, though it shows lower capacity fading rate than 700 °C sample. For Fe₂P containing samples, the diffusion coefficient of Li⁺ ion increases with increasing amount of Fe₂P, however, the sample synthesized at 900 °C shows much lower Li⁺ ion diffusion coefficient due to the hindrance of Fe₂P layer on the surface of LiFePO₄ particles.     

Hollow Co3O4 thin films as high performance anodes for lithium-ion batteries

Cobalt oxide thin films composed of hollow spherical Co₃O₄ particles have been prepared by a two-step method. The first step involves in the synthesis of hollow cobalt alkoxide particles in a stable suspension from mixed polyalcohol solutions of cobalt acetate in oil bath at 170 °C. The second step includes the thin film fabrication by electrostatic spray deposition (ESD) and subsequent heat treatment in nitrogen. The obtained Co₃O₄ films with the unique hollow particle microstructure exhibit high reversible capacity of above 1000 mAh g⁻¹ during up to 50 cycles and good rate capability. The films are promising negative electrodes for high energy lithium-ion batteries.     

Core/shell Fe3O4@Fe encapsulated in N-doped three-dimensional carbon architecture as anode material for lithium-ion batteries

Core-shell Fe₃O₄@Fe nanoparticles embedded into porous N-doped carbon nanosheets was prepared by a facile method with NaCl as hard-template. The three-dimensional carbon architecture built by carbon nanosheets enhance the conductivity of the encapsulated Fe₃O₄@Fe nanoparticles and strengthen the structure stability suffering from volume expansion during extraction and insertion of lithium ions. Rich Pores enhance the surface between electrode and electrolyte, which short the transmission path of ions and electrons. The core-shell structure with Fe as core further improves charge transferring inside particles thus lead to high capacity. The as-prepared Fe₃O₄@Fe/NC composite displays an irreversible discharge capacity of 839 mAh g^?1 at 1 A g^?1, long cycling life (722.2 mAh g^?1 after 500th cycle at 2 A g^?1) and excellent rate performance (1164.2 and 649.2 mAh g^?1 at 1 and 20 A g^?1, respectively). The outstanding electrochemical performance of the Fe₃O₄@Fe/NC composite indicates its application potential as anode material for LIBs.     

Facile synthesis and electrochemical properties of Fe3O4 nanoparticles for Li ion battery anode

Nanostructured Fe₃O₄ nanoparticles were prepared by a simple sonication assisted co-precipitation method. Transmission electron microscopy, X-ray diffraction and BET surface area analysis confirmed the formation of ∼20 nm crystallites that constitute ∼200 nm nanoclusters. Galvanostatic charge-discharge cycling of the Fe₃O₄ nanoaprticles in half cell configuration with Li at 100 mA g⁻¹ current density exhibited specific reversible capacity of 1000 mAh g⁻¹. The cells showed stability at high current charge-discharge rates of 4000 mA g⁻¹ and very good capacity retention up to 200 cycles. After multiple high current cycling regimes, the cell always recovered to full reversible capacity of ∼1000 mAh g⁻¹ at 0.1 C rate.     

Synthesis and electrochemical performances of Li3V2(PO4)3/(Ag + C) composite cathode

Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C and Li₃V₂(PO₄)₃/(Ag + C) composites as cathodes for Li ion batteries are synthesized by carbon-thermal reduction (CTR) method and chemical plating reactions. The microstructure and morphology of the compounds are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The Li₃V₂(PO₄)₃/(Ag + C) particles are 0.5-1 μm in diameters. As compared to Li₃V₂(PO₄)₃, Li₃V₂(PO₄)₃/C, the Li₃V₂(PO₄)₃/(Ag + C) composite cathode exhibits high discharge capacity, good cycle performance (140.5 mAh g⁻¹ at 50th cycle at 1 C, 97.3% of initial discharge capacity) and rate behavior (120.5 mAh g⁻¹ for initial discharge at 5 C) for the fully delithiated (3.0-4.8 V) state. Electrochemical impedance spectroscopy (EIS) measurements show that the carbon and silver co-modification decreases the charge transfer resistance of Li₃V₂(PO₄)₃/(Ag + C) cathode, and improves the conductivity and boosts the electrochemical performance of the electrode.     

PVDF-HFP/PET/PVDF-HFP composite membrane for lithium-ion power batteries

In this study, a novel polymer electrolyte composite membrane is successfully fabricated using electrospinning and solution casting. The composite membrane comprises two microporous poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) layers plus an intermediate quaternary ammonium-containing SiO₂ nanoparticles modified polyethylene terephthalate (PET) nanofibrous nonwoven to form a sandwiched PVDF-HFP/PET/PVDF-HFP composite, which is employed as a separator for lithium-ion batteries (LIBs). The properties of the PET composite membrane are compared with those of commercial PE separator, such as the morphologies, physical properties, and electrochemical performances. According to our results, the composite membrane demonstrates superior thermal stability (thermal shrinkage ～8%), electrolyte-philicity (contact angle ～2.9°), electrolyte uptake and retention (282%, 74%), and ionic conductivity (～10^?3 S cm^?1). The separators are assembled into Li/LiFePO₄ cells for electrochemical tests, showing that the PET composite membrane cells exhibit higher capacities than those with the PE separator at 0.2–10C both at 25 °C and 55 °C. The discharge capacity retention and coulombic efficiency of the PET composite membrane cells at 1C/1C for 200 cycles can be respectively enhanced about 20% and 2% at 55 °C as compared to the PE separator cells. These results demonstrate that our prepared PET composite membrane is highly promising for LIB applications.     

Lithium diffusion in Li4Ti5O12 at high temperatures

Synthesis of the spinel lithium titanate Li₄Ti₅O₁₂ by an alkoxide-free sol-gel method is described. This method yields highly pure and crystalline Li₄Ti₅O₁₂ samples at relatively low temperature (850 °C) and via short thermal treatment (2 h). ⁶Li magic angle spinning nuclear magnetic resonance (MAS NMR) measurements on these samples were carried out at high magnetic field (21.1 T) and over a wide temperature range (295-680 K). The temperature dependence of the chemical shifts and integral intensities of the three ⁶Li resonances demonstrates the migration of lithium ions from the tetrahedral 8a to the octahedral 16c sites and the progressive phase transition from a spinel to a defective NaCl-type structure. This defective structure has an increased number of vacancies at the 8a site, which facilitate lithium diffusion through 16c → 8a → 16c pathways, hence providing an explanation for the reported increase in conductivity at high temperatures. Molecular dynamics simulations of the spinel oxides Li_4+xTi₅O₁₂, with 0 ≤ x ≤ 3, were also performed with a potential shell model in the temperature range 300-700 K. The simulations support the conclusions drawn from the NMR measurements and show a significant timescale separation between lithium diffusion through 8a and 16c sites and that out of the 16d sites.     

Synthesis and improved electrochemical performances of porous Li3V2(PO4)3/C spheres as cathode material for lithium-ion batteries

Spherical Li₃V₂(PO₄)₃/C composites are synthesized by a soft chemistry route using hydrazine hydrate as the spheroidizing medium. The electrochemical properties of the materials are investigated by galvanostatic charge-discharge tests, cyclic voltammograms and electrochemical impedance spectrum. The porous Li₃V₂(PO₄)₃/C spheres exhibit better electrochemical performances than the solid ones. The spherical porous Li₃V₂(PO₄)₃/C electrode shows a high discharge capacity of 129.1 and 125.6 mAh g⁻¹ between 3.0 and 4.3 V, and 183.8 and 160.9 mAh g⁻¹ between 3.0 and 4.8 V at 0.2 and 1 C, respectively. Even at a charge-discharge rate of 15 C, this material can still deliver a discharge capacity of 100.5 and 121.5 mAh g⁻¹ in the potential regions of 3.0-4.3 V and 3.0-4.8 V, respectively. The excellent electrochemical performance can be attributed to the porous structure, which can make the lithium ion diffusion and electron transfer more easily across the Li₃V₂(PO₄)₃/electrolyte interfaces, thus resulting in enhanced electrode reaction kinetics and improved electrochemical performance.     

Improved electrochemical performances of 9LiFePO4·Li3V2(PO4)/C composite prepared by a simple solid-state method

9LiFePO₄·Li₃V₂(PO₄)₃/C is synthesized via a carbon thermal reaction using petroleum coke as both reduction agent and carbon source. The as-prepared material is not a simple mixture of LiFePO₄ (LFP) and Li₃V₂(PO₄)₃ (LVP), but a composite possessing two phases: one is V-doped LFP and the other is Fe-doped LVP. The typical structure enhances the electrical conductivity of the composite and improves the electrochemical performances. The first discharge capacity of 9LFP·LVP/C in 18650 type cells is 168 mAh g⁻¹ at 1 C (1 C_9LFP·LVP/C = 166 mA g⁻¹), and exhibits high reversible discharge capacity of 125 mAh g⁻¹ at 10 C even after 150 cycles. At the temperature of −20 °C, the reversible capacity of 9LFP·LVP/C can maintain 75% of that at room temperature.     

Controlled synthesis of α-Fe2O3 nanostructures and their size-dependent electrochemical properties for lithium-ion batteries

Highly crystalline hematite α-Fe₂O₃ nanostructures were selectively synthesized by a simple hydrothermal method. By carefully tuning the concentration of the reactants, reaction time and pressure, a series of α-Fe₂O₃ nanocuboids, nanospheres, nanosheets, nanorods and nanowires can be obtained. Based on the evidence of electron microscope images, a formation mechanism for nanowire-structured hematite is proposed. The electrochemical performance of these hematite nanostructures as anode materials for lithium-ion batteries was further evaluated by cyclic voltammetry, electrochemical impedance and charge–discharge measurements. It was demonstrated that both the morphology and the particle size have an influence on the performance. The results showed that the nanospheres displayed the highest discharge capacity and superior cycling reversibility, which may result from the high surface area and small and uniform grain size.     

Improvement of electrochemical behavior of Sn2Fe/C nanocomposite anode with Al2O3 addition for lithium-ion batteries

Sn₂Fe/Al₂O₃/C nanocomposites are synthesized using a high-energy, mechanical milling method with thermally synthesized Sn₂Fe, Al₂O₃ and carbon (Super P) powders. The effect of Al₂O₃ addition on the microstructure of the Sn₂Fe/Al₂O₃/C nanocomposites is examined. The electrochemical characteristics of the material as an anode in lithium-ion batteries are also evaluated. High-resolution transmission electron microscopy shows that the crystallite size of active Sn₂Fe in the Sn₂Fe/Al₂O₃/C nanocomposite is smaller than that of the Sn₂Fe/C nanocomposite without Al₂O₃. A decrease in the initial irreversible capacity and enhanced cycle performance of the Sn₂Fe/Al₂O₃/C nanocomposite electrode are observed.