Comparative study of aluminum diethylphosphinate and aluminum methylethylphosphinate‐filled epoxy flame‐retardant composites

Epoxy resin (EP) is one of the main polymers in electrical and electronic applications. In this work, flame‐retardant epoxy resin composites based on aluminum diethylphosphinate (Al(DEP)) and aluminum methylethylphosphinate (Al(MEP) were prepared using aromatic amine 4, 4‐diaminodiphenylmethane as curing agent. The flammability, thermal degradation, flexural properties, and morphologies of composites were investigated with respect to the filler loading and filler type. Results showed that both Al(MEP) and Al(DEP) were efficient flame retardants for EP and a low dosage (15 wt%) is enough to achieve the important criterion UL 94 V‐0. Limiting oxygen index (LOI) of composites is increased with filler loading (phosphorus content) and reached of 32.2% for 15 wt% of Al(MEP) and 29.8 for 15 wt% of Al(DEP). The char formation and flexural modulus of composites are also improved by adding the two fillers. However, the flexural strength of all the composites decreased with increasing filler loading. In comparison with Al(DEP)/EP, Al(MEP)/EP provides a higher flammability, better thermal stability and char formation but inferior flexural properties. Scanning electron microscopy revealed that the dispersion of Al(DEP) filler in the EP matrix is more uniform and exhibits better compatibility with EP matrix, which in turn generates better flexural strength and higher modulus when compared with Al(MEP)‐filled EP composites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Synergistic effects of carbon fillers on tensile and flexural properties in liquid‐crystal polymer based resins

One emerging market for thermally and electrically conductive resins is bipolar plates for use in fuel cells. Adding carbon fillers to thermoplastic resins increases the composite thermal and electrical conductivity. These fillers have an effect on the composite tensile and flexural properties, which are also important for bipolar plates. In this study, various amounts of three different types of carbon (carbon black, synthetic graphite particles, and carbon fibers) were added to Vectra A950RX liquid‐crystal polymer. In addition, composites containing combinations of fillers were also investigated via a factorial design. The tensile and flexural properties of the resulting composites were then measured. The objective of this study was to determine the effects and interactions of each filler with respect to the tensile and flexural properties. The addition of carbon black caused the tensile and flexural properties to decrease. Adding synthetic graphite particles caused the tensile and flexural modulus to increase. The addition of carbon fiber caused the tensile and flexural modulus and ultimate flexural strength to increase. In many cases, combining two different fillers caused a statistically significant effect on composite tensile and flexural properties at the 95% confidence level. For example, when 40 wt % synthetic graphite particles and 4 wt % carbon black were combined, the composite ultimate tensile and flexural strength increased more than what would be expected from the individual additive effect of each single filler. It is possible that linkages were formed between the carbon black and synthetic graphite particles that resulted in improved ultimate tensile and flexural strength. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical and thermal properties of ABS and leather waste composites

To determine the possibility of using leather waste as reinforcing filler in the thermoplastic polymer composite, acrylonitrile–butadiene–styrene (ABS) as the matrix and leather buffing powder as reinforcing filler were used to prepare a particulate reinforced composite to determine testing data for the physical, mechanical, and thermal properties of the composites, according to the filler loading in respect to thermoplastic polymer. The ABS and leather powder composites were prepared by the extrusion of ABS with 2.5, 5, 7.5, 10, 12.5, and 15 wt % of leather powder in corotating twin screw extruder. The extruded strands were cut into pellets and injection molded to make specimens. These specimens were tested for physicomechanical properties like tensile and flexural strengths, tensile and flexural modulus, Izod and charpy impact strength, abrasion resistance, Rockwell hardness, density, Heat deflection temperature (HDT) and Vicat softening point (VSP), water absorption, and thermal degradation analysis. The incorporation of leather waste powder does not affect the tensile, flexural strengths, Izod impact strength, abrasion resistance, Rockwell hardness, density, HDT and VSP values drastically. However, the tensile modulus, tensile elongation, and charpy impact strength values are reduced significantly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3062–3066, 2006     

Effect of single‐mineral filler and hybrid‐mineral filler additives on the properties of polypropylene composites

The present study was carried out to determine the filler characteristics and to investigate the effects of three types of mineral fillers (CaCO₃, silica, and mica) and filler loadings (10–40 wt%) on the properties of polypropylene (PP) composites. The characteristics of the particulate fillers, such as mean particle size, particle size distribution, aspect ratio, shape, and degree of crystallinity were identified. In terms of mechanical properties, for all of the filled PP composites, Young's modulus increased, whereas tensile strength and strain at break decreased as the filler loading increased. However, 10 wt% of mica in a PP composite showed a tensile strength comparable with that of unfilled PP. Greater tensile strength of mica/PP composites compared to that of the other composites was observed because of lower percentages of voids and a higher aspect ratio of the filler. Mica/PP also exhibited a lower coefficient of thermal expansion (CTE) compared to that of the other composites. This difference was due to a lower degree of crystallinity of the filler and the CTE value of the mica filler. Scanning electron microscopy was used to examine the structure of fracture surfaces, and there was a gradual change in tensile fracture behavior from ductile to brittle as the filler loading increased. The nucleating ability of the fillers was studied with differential scanning calorimetry, and a drop in crystallinity of the composites was observed with the addition of mineral filler. Studies on the hybridization effect of different (silica and mica) filler ratios on the properties of PP hybrid composites showed that the addition of mica to silica‐PP composites enhanced their tensile strength and modulus. J. VINYL ADDIT. TECHNOL., 2009. © 2009 Society of Plastics Engineers     

A comparative study on some properties of wood plastic composites using canola stalk,Paulownia, and nanoclay

In this research, the reinforcing effect of fillers including canola stalk, paulownia and nanoclay, in polypropylene (PP) has been investigated. In the sample preparation, 50 wt% of lignocellulosic materials and 0, 3, and 5 wt% of nanoclay particles were used. The results showed that while flexural and tensile properties were moderately enhanced by the addition of nanoclay in the matrix, notched Izod impact strengths decreased dramatically. However, with increase in the nanoclay content (5 wt%), the flexural and tensile properties decreased considerably. The mechanical properties of composites filled with paulownia are generally greater than canola stalk composites, due to the higher aspect ratio. The thickness swelling and water absorption of the composites significantly decreased with the increase in nanoclay loading. Except tensile modulus, the differences between the type of fibrous materials and nanoclay contents had significant influence on physicomechanical properties. Morphologies of the composites were analyzed using transmission electron microscopy (TEM) and X‐ray diffraction (XRD), and the results showed increased d‐spacing of clay layers indicating enhanced compatibility among PP, clay, and lignocellulosic material. TEM micrographs also confirmed that the composites containing 3 wt% nanoclay had uniform dispersion and distribution of clay layers in the polymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

A comparative analysis of woven jute/glass hybrid polymer composite with and without reinforcing of fly ash particles

The objective of this research article is to compare the mechanical and tribological properties of jute‐glass‐fiber‐reinforced epoxy (J‐G‐E) hybrid composites with and without fly ash particulate filler. A dry hand lay‐up technique is used to fabricate all the laminates. The properties including flexural strength, tensile strength, flexural modulus, and erosion behavior of all the composites are evaluated as per American Society for Testing and Materials (ASTM) standards. The fly ash particulate‐filled hybrid composite shows a better mechanical and tribological property. The maximum flexural strength and flexural modulus are obtained for GJGJ+ 5 wt% fly ash filler epoxy composites. Whereas the maximum tensile strength is obtained for GJJG+ 10 wt% fly ash filler epoxy composites. Scanning Electron Microscopy (SEM) analysis also has been carried out to categorize mechanical and tribological behavior of composites. POLYM. COMPOS. 37:658–665, 2016. © 2014 Society of Plastics Engineers     

Investigation on physicomechanical and wear properties of new green thermoplastic composites

This study was aimed at fabrication of green composites of polypropylene (PP) matrix 5, 10, 15, and 20 wt% of saw palmetto spent (SPS) (a spent of nutraceuticals) as filler material. Two wt% organically modified montmorillonite clay (MMT) was used as a co‐filler in all formulations and composites were fabricated by melt blending. The fabricated PP/SPS/MMT composites were characterized for physicomechanical and tribological properties. Improvement in tensile modulus of the composites was noticed with increase in SPS content. The tensile strength of composites was decreased by 14% with increase in filler content from 5 to 20 wt%. Flexural strength of the composites increased from 31.3 to 37.8 MPa (21% improvement) and also flexural modulus improved from 956 to 1383 MPa (45% improvement) with increased SPS content. Composites were subjected to three‐body abrasion with different loads and abrading distances. Scanning electron microscope (SEM) study revealed that the predominant wear mechanisms of composite material sliding against continuous flowing sand were microploughing and filler detachment from the polymer matrix. POLYM. COMPOS., 37:2306–2312, 2016. © 2015 Society of Plastics Engineers     

Performance of bamboo plastic composites with hybrid bamboo and precipitated calcium carbonate fillers

The influences of hybrid bamboo and precipitated calcium carbonate (PCC) fillers in a recycled polypropylene/polyethylene matrix on the properties of bamboo plastic composites were studied. Thermogravimetric and Fourier transform infrared analyses of both thermo‐mechanically refined bamboo fiber (RBF) and ground bamboo particle (GBP) showed relatively higher holocellulose content in RBF, and more effective silane grafting on the RBF surface. The raw PCC particles contained over 95% calcium carbonate, and had an agglomerated form consisting of particles with a mean diameter of about 1.2 microns. Compounding the PCC particles with the plastic resin helped separate and disperse them in the matrix. Measured flexural strength and modulus of PCC‐only‐filled composites increased significantly from 15 to 30% PCC content levels, while the tensile and impact strength of composites decreased with the addition of PCC. For composites with hybrid bamboo and PCC fillers, tensile and flexural moduli were improved with the increase of PCC content. After silane treatment, RBF‐filled composites showed noticeably increased mechanical properties compared with those of GBP‐filled composites. For modulus values, PCC–bamboo–polymer composites were 3–4 times higher than those of PCC–polymer composites at high PCC levels. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

矿物填料填充聚乙烯/麦秸杆复合材料性能比较

以麦秸杆纤维(WSF)和高密度聚乙烯(PE-HD)为原料,以白云石粉、硅灰石粉及滑石粉为填充料,通过熔融混炼及注射成型的方法制备了PE-HD/WSF/填料复合材料,并通过差示扫描量热仪、扫描电子显微镜和电子万能试验机等考察分析了填料种类及含量对复合材料结晶性能、微观形貌和力学性能等的影响.结果表明,在WSF的含量为40...     

Impact of delignification on mechanical,morphological, and thermal properties of wood sawdust reinforced unsaturated polyester composites

Mechanical, morphological, and thermal properties of the raw and delignified wood sawdust (DWS) reinforced unsaturated polyester (UP) composites were evaluated. Composites were prepared using Resin Transfer molding technique by changing filler loading (5, 10, 15, and 20 wt%) for both raw and DWS reinforced UP. Mechanical (tensile and flexural), Fourier transform infrared spectroscopy (FTIR), morphological (scanning electron microscopy [SEM]) and thermal (thermogravimetric analysis [TGA]) properties were successively characterized. FTIR confirmed the removal of lignin from wood sawdust during the delignification process. The tensile strength, Young's modulus, and flexural strength values increased only up to 15% filler loading then decreased with increasing the filler. DWS reinforced composites had better mechanical properties compared to raw composites. SEM micrographs reveal that DWS reinforced composites have good compatibility with UP resin. According to TGA results, DWS reinforced composites showed enhanced thermal stability at the final decomposition stage above 400°C. J. VINYL ADDIT. TECHNOL., 24:185–191, 2018. © 2016 Society of Plastics Engineers     

Studies on High Density Polyethylene Reinforced with Phosphate Ore Particles: Thermal,Rheological, Mechanical and Morphological Properties

Calcareous phosphate ore can be utilized as a cost-effective alternate to other inorganic fillers for polymer-based composites. In this study, composites of high-density polyethylene and phosphate rock ore particles were prepared by melt blending and injection-molding techniques. The thermomechanical, rheological, and mechanical properties of these composites were studied to investigate the effect of filler loading on their functionality. The reduction in the crystallinity of phosphate ore/high-density polyethylene composites was observed compared to that of the neat high-density polyethylene. The relative crystallinity of the neat high-density polyethylene decreases from 53 to 30% by the addition of 2.5–15 wt% of ore, respectively. Comparison of the linear dynamic viscoelasticity for the neat high-density polyethylene and the ore-filled composites shows t a monotonic increase in both storage modulus and loss modulus with the increasing frequency. The viscoelastic behavior at high frequencies remains unaffected. However, at lower frequencies, both G′ and G″ exhibit diminished frequency dependence. It was also observed that higher filler content decreased the tensile and impact strength, whereas the Young's modulus of the composites increased. The morphological analysis shows relatively weak interaction between the fillers and the matrix because of agglomeration which in turn adversely affects the mechanical properties of the composites.     

Injection molding of biodegradable polyester blends filled with mineral and sustainable fillers: Performance evaluation

This research focuses on the melt processing of biocomposites from a biodegradable polymer blend mixed with hybrid fillers through injection molding technique. An optimized blend ratio (60/40 wt%) poly(butylene succinate-co-butylene adipate) (PBSA) and poly(butylene adipate-co-terephthalate) (PBAT) demonstrated promising results after blending with a mixture of walnut shell powder (WSP), corn starch and talc in various proportions for use in rigid packaging. The addition of hybrid fillers (i) 10% WSP with 15% talc and (ii) 5% WSP with 5% starch and 15% talc to the polymer blend (60%PBSA/40%PBAT) improved tensile modulus (160% and 162%, respectively) and flexural modulus (147% and 153%, respectively) because of the dispersion of stiffer talc and WSP. Following the addition of fillers, tensile strength of the composites decreased. However, flexural strength improved significantly after filler introduction because of better stress transfer ability. Rheological analysis of filled composites with starch or WSP (25%) depicted similar characteristics of the polymer blend, indicating lower viscosity than hybrid composites. The abundant hydroxyl groups in starch explained the increased water absorption and decreased contact angle compared with other composites. This research's novelty encompasses utilizing low-cost biomasses with mineral filler into an under-researched biodegradable polymer blend suitable for single-use rigid packaging applications.     

Improved strength and toughness of polyketone composites using extremely small amount of polyamide 6 grafted graphene oxides

Polyketone (PK) composites were prepared by a solution casting method using 1,1,1,3,3,3-hexafluoro-2-propanol as a solvent and polyamide 6 grafted graphene oxides (PA 6-GOs) as filler materials. PA 6-GOs were obtained by in situ polymerization of ε-caprolactam using GOs having different amounts of oxygen functional groups. The PK composites containing only an extremely small amount of the PA 6-GOs (0.01 wt%) showed much improved mechanical properties compared to PK. This could be ascribed to the homogeneous dispersion of the graphene-based filler materials in the polymer and specific interactions such as dipole–dipole interactions and/or the hydrogen bonds between the fillers and the polymer matrix. For example, when 0.01 wt% of PA 6-GO having less oxygen functional groups was used as a filler for the composite, the tensile strength, Young’s modulus, and elongation at break of the composite increased by 35%, 26%, and 76%, respectively. When 0.01 wt% of PA 6-GO having larger content of oxygen functional groups and PA 6 was used, Young’s modulus decreased, while the tensile strength increased by 37%, and the elongation at break increased tremendously by 100 times, indicating that very tough polymeric materials could be prepared using a very small amount of the graphene-based fillers.     

The Physical Properties of Oil Palm Empty Fruit Bunch (EFB) Composites Made from Various Thermoplastics

Abstract

Oil palm empty fruit bunch (EFB)-based composites were produced using different types of thermoplastic as matrices. The composites were produced by using an internal mixer. The mechanical and water absorption properties of composites were investigated. Overall, the incorporation of EFB into the polymer matrix has resulted in the reduction of flexural strength. The poor performance has been attributed to the poor filler-matrix interaction. Both flexural and tensile modulus of PE and PP composites have been improved upon the addition of fillers, however, both PS and PVC composites showed a decreasing trend. Tensile strength and elongation at break results for all composites have been reduced as the result of incorporation of filler. This has been attributed to the poor filler-matrix interaction or compatibility, size irregularity and also decreased ductile deformation. Water absorption and thickness swelling increased as the filler loading is increased. This has been attributed to the presence of hyrophillic hydroxyl groups of the filler.     

Dynamic mechanical properties of some epoxy matrix composites

Dynamic mechanical properties of some epoxy matrix composites have been studied, comparing experimental data with theoretical models. The matrix in all composite samples was Shell Epon 828, a diglycidyl ether of bisphenol A, cured with meta-phenylenediamine. Fibrous composite samples were made with glass and graphite fibers. Particulate composite samples were made with glass microspheres, atomized aluminum, powdered silica, alumina, asbestos, mica, carbon black, and graphite. The dynamic elastic modulus and damping of these samples were measured at temperatures between 85° and 345°K by a free-free flexural resonance technique. The dynamic modulus of parallel fiber composites follows the linear rule of mixtures for low fiber volume fractions; deviations from linearity at higher volume fractions appear to be due to defects caused by the sample fabrication technique. Dynamic moduli of the particulate composites conform, within experimental error, to the static modulus theory of Wu up to filler volume fractions of 0.35 to 0.40. Deviations from Wu's theory at higher volume fractions may be due to agglomeration of filler particles. The damping of particulate composites with quasi-spherical filler particles appears to follow the rule of mixtures. In particulate composites with needle- and flake-type fillers, and in fibrous composites, the fillers are more highly stressed; with more of the strain energy in the low-damping fillers, overall damping is reduced. Damping greater than that attributable to the matrix and filler may be due to slippage at the interface between them. In addition to supporting Wu's theory of the elastic modulus of a particulate composite, this study demonstrates the utility of the nondestructive free-free flexural resonance techniques for obtaining a large body of reliable data in a short time from relatively few small samples. This greatly facilitates the experimental testing of theoretical models and the evaluation of fillers, matrix materials, and fabrication techniques.     

Tensile properties of carbon filled liquid crystal polymer composites

Electrically and thermally conductive resins can be produced by adding carbon fillers. Mechanical properties such as tensile modulus, ultimate tensile strength, and strain at ultimate tensile strength are vital to the composite performance in fuel cell bipolar plate applications. This research focused on performing compounding runs followed by injection molding and tensile testing of carbon filled Vectra A950RX liquid crystal polymer composites. The four carbon fillers investigated included an electrically conductive carbon black, thermocarb synthetic graphite particles, and two carbon fibers (Fortafil 243 and Panex 30). For each different filler type, resins were produced and tested that contained varying amounts of these single carbon fillers. The carbon fiber samples exhibited superior tensile properties, with a large increase in tensile modulus over the base polymer, and very low drop in the ultimate tensile strength as the filler volume fraction was increased. The strain at the ultimate tensile strength was least affected by the addition of the Panex carbon fiber but was significantly affected by the Fortafil carbon fiber. In general, composites containing synthetic graphite did not perform as well as carbon fiber composites. Carbon black composites exhibited poor tensile properties. POLYM. COMPOS., 29:15–21, 2008. © 2007 Society of Plastics Engineers     

Dynamic mechanical analysis and morphological studies of fly ash/mica reinforced poly(ether‐ether‐ketone)‐based hybrid composites

Hybrid composites based on poly(ether‐ether‐ketone) (PEEK) were fabricated with fly ash and mica. Nearly 5, 10, and 15 wt% of fly ash were replaced by mica of the optimized fly ash reinforced composites and were subjected to dynamical mechanical analysis to determine the dynamic properties as a function of temperature. The storage modulus E′ was found to decrease with the increase of weight fraction of mica. Loss modulus was also found to decrease with loading while the damping property was found to increase marginally. Peak height of tan δ for hybrid composites were decreased by varying combinations of fly ash with mica. It is probably due to improved crystallinity of PEEK and strong interaction between the fillers and PEEK matrix. Cole–Cole analysis was made to understand the phase behavior of the composite samples. Kubat parameter was calculated to study the adhesion between matrix and filler of the fabricated composites. Without surface modification for inorganic fillers, the distribution of two different shape filler particles appears to be reasonably uniform. The use and limitation of various theoretical equations to predict the tan δ and storage modulus of filler reinforced composites have been discussed. Addition of both fillers opens up new opportunities for development of high‐performance multifunctional materials suitable for industrial applications. Scanning electron micrographs of tensile fracture surfaces of composites demonstrated filler–matrix bonding. POLYM. COMPOS., 35:68–78, 2014. © 2013 Society of Plastics Engineers     

Tensile properties of polypropylene/kaolin composites

Tensile properties of isotactic polypropylene filled with particulate kaolin fillers were evaluated in the composition range 0–60 wt % kaolin. Tensile modulus increased with filler concentration while breaking elongation and tensile strength decreased. The modulus increase was attributed to the restriction on the molecular mobility of the polymer imposed by kaolin particles. The decrease in elongation was also an effect of this restriction coupled with interference to stress transfer by the filler particles. Generation of discontinuity in the composite structure through formation of stress concentration points accounted for the tensile strength decrease. Morphology studies by SEM also indicated the introduction of stress concentration points by the presence of bare and nonadherent kaolin particles and their agglomerates with sharp edges in these composites.     

Effects of graphite filler loading and heat treatment temperature on the properties of phenolic resin based carbon–carbon composites

Carbon/carbon composites (C/Cs) were prepared through polymer pyrolysis using PAN based carbon fabric (Panex^(R) 35) and resol type phenolic resin having 0, 10, 20, 30, and 40 wt% of graphite fillers. These precursor composites were heat treated at 600, 900, and 1200°C. The effects of filler loading on the precursor composites and their C/Cs were investigated through density, microstructure, and mechanical properties. Since, the precursor composites were prepared under similar processing conditions and technique, at any particular filler loading when the heat treatment temperature increases, the bulk density of the samples decreases. The filler addition accelerates the formation of the carbon basal planes in the matrix supported by X‐ray diffraction studies. The properties such as tensile strength and strain decrease continuously mainly due to change in the matrix structure and decrease of density, whereas, the interlaminar shear strength (ILSS) and interlaminar fracture toughness (ILFT) increase mainly because of improvement in the modulus of matrix. At any particular heat treatment temperature, depending on the filler content and matrix type, the density, tensile properties, ILSS, and ILFT of the samples show different trends. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

The effect of alkali treatment and filler size on the properties of sawdust/UPR composites based on recycled PET wastes

In this study, natural sawdust fillers from acacia were mixed with unsaturated polyester resin (UPR), which was prepared by recycling of polyethylene terephthalate (PET) waste bottles to prepare sawdust/UPR composite. PET wastes were recycled through glycolysis and depolymerized to produce a formulation for the resin. The effects of alkali treatment, filler content, and filler size on the tensile, flexural, hardness, and water absorption of the composites were investigated. The results show that the modulus of both tensile and flexural increased with increasing filler contents, but the tensile and flexural strength of composites decreased. The size of sawdust also played a significant role in the mechanical properties, with smaller size sawdust producing higher strength and modulus. This is due to the greater surface area for filler–matrix interaction. The results also show that alkali treatment causes a better adhesion between sawdust and UPR matrix and improves the mechanical properties of the composites. Furthermore, surface treatment reduced the water absorption of composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008