Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

The hydration phase and pore structure formation in the blends of sulfoaluminate-belite cement with Portland cement

Sulfoaluminate-belite (SAB) cements are an attractive class of low-energy cements from the viewpoint of saving energy and releasing less CO₂ into the atmosphere during their production. Their hydraulic activity, however, does not match that of the ordinary Portland cement (PC) and needs improvement before they can be used on their own. However, SAB cements when blended with PC have the potential to be used effectively in traditional applications as shown by this study. Mortars made with blends of SAB cements and PC, and a cement-to-sand ratio of 1:3 by weight and a water-to-cement ratio of 0.5, indicate a superior protection against corrosion of steel to those made with blends of PC and blast-furnace slag (BFSPC). The prepared mortars were stored at 20 °C for 90 days under either a 60% relative humidity (RH)-dry air, or 100% RH-wet air conditions. With further improvement in the SAB cement quality through better understanding of their characteristics, a genuine competition between SAB/PC and BFSPC can be expected in practice.     

Sphere Lower Bound for Rotated Lattice Constellations in Fading Channels

We study the error probability performance of rotated lattice constellations in frequency-flat Nakagami-m block-fading channels. In particular, we use the sphere lower bound on the underlying infinite lattice as a performance benchmark. We show that the sphere lower bound has full diversity. We observe that optimally rotated lattices with largest known minimum product distance perform very close to the lower bound, while the ensemble of random rotations is shown to lack diversity and perform far from it.     

Polyesterification and isomerization of maleic anhydride and 1,6-hexane diol as studied by 1H and 13C n.m.r.

The polyesterification and isomerization reaction of 1,6-hexane diol and maleic anydride in a melt without catalyst was studied by ¹³C and ¹H n.m.r. spectroscopy. The structure and concentration of oligoester species during the polyesterification and isomerization were determined depending on the reaction temperature and time. According to the number and configuration of repeating units determined from ¹H n.m.r. spectra kinetics of both reactions were also considered. The degree of isomerization is continuously increasing in the investigated reaction range.     

Experimental observation of temperature gradients occurring in a single zeolite pellet

An experimental study has been made of temperature profiles incident within a zeolite adsorbent particle in the course of adsorption of n-heptan. Using thermocouple wires 0.1 mm in diameter it has been possible to measure simultaneously the temperatures of the surface and in the centre. It was observed that temperature differences between center of the pellet and ambient stagnant gas may be more than 20°C. The results of this work indicate that the overheating of an adsorbent particle is a very rapid process which is followed by a slow cooling of the hot particle. Experimental data are compared with predictions calculated from the theoretical model.     

Solvent induced crystallization of syndiotactic poly(methyl methacrylate) relation to the formation of polymer aggregates in solution

Polymer Bulletin - Solutions of syndiotactic (s) poly (methyl methacrylate) (PMMA) and samples of solid s-PMMA prepared from these solutions were studied by NMR and infrared (IR) spectroscopy and...     

Study of rotational mobility of stable nitroxide radicals in solid polymers

The rotational mobility of stable nitroxide radicals in PS, PMMA, PVC, PP and PE has been studied over a wide temperature range by the e.s.r. method. At temperatures T lower than T_g, spin probes act as kinetically independent particles, the rotational frequency of which is deter mined mainly by the micropore dimensions of the polymer and depends indirectly on the mobility of segments or side groups.