Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Purification of Ellagic Acid by UF Membranes

Ellagic acid (2, 3, 7, 8‐tetrahydroxy(1)benzopyrano(5, 4, 3‐cde)(1)benzopyran‐5, 10‐dione) was selected as a model pollutant which is present in the tannic fraction of cork processing wastewater. The ultrafiltration of aqueous ellagic acid solutions through three membranes was studied in tangential UF laboratory equipment. Two of the membranes were polyethersulfone (Biomax10K and Biomax5K, with MWCO of 10000 and 5000 Da, respectively), and the third made of regenerated cellulose (Ultracel5K, with MWCO of 5000 Da). The water hydraulic permeability was evaluated for each membrane. The evolution of the permeate flow rate with processing time was followed, and the influence of the main operating variables (feed flow rate, trans‐membrane pressure and nature of the membranes) on the permeate flux was also established. According to the hypothesis of the film theory, the intrinsic and apparent rejection coefficients, as well as the mass transfer coefficients, were also determined, and the values obtained were discussed as a function of the operating conditions used.     

Correlation between synthesis conditions, coherently diffracting domain size and cubic phase stabilization in barium titanate

The Constant Rate Thermal Analysis method has been used under different experimental conditions to obtain barium titanate powder of very small grain size. Both a crystallographic and a dielectric study ham been carried out on samples sintered at different temperatures. It is deduced that the formation of small coherently diffracting domains is improved by the generation of oxygen vacancies and the cubic phase stabilization depends on the coherently diffracting domain size rather than on the particle size.     

Stochastic stabilization of differential systems with general decay rate

Some sufficient conditions concerning stability of solutions of stochastic differential evolution equations with general decay rate are first proved. Then, these results are interpreted as suitable stabilization ones for deterministic and stochastic systems. Also, they permit us to construct appropriate linear stabilizers in some particular situations.     

A CMOS rectifier-integrator for amplitude detection in hard diskservo loops

In this paper a CMOS alternative amplitude detection system is presented. It is designed as an alternative for the, bipolar, amplitude detection in hard disk servo systems. The amplitude is detected by converting the input voltage to a current, rectifying the current, and integrating it on a capacitor. For this a new OTA topology and a rectifier cell are designed. This circuitry is expanded with a very linear current mirror and an automatic offset compensation system to cope with technology spread. The measured accuracy of the amplitude detector is 0.2% (9 b). This makes the circuit suitable for implementation in state-of-the art hard disk systems with very high track densities and very short access times. Because the circuit is realized in standard CMOS it is a further step toward CMOS only hard disk electronics. Because the circuit operates from a single 3 V power supply and has limited power consumption it can be used in battery powered systems     

Use of an environmental specimen bank for evaluating the impact of the Prestige oil spill on the levels of trace elements in two species of Fucus on the coast of Galicia (NW Spain)

In the present study we investigated possible contamination by trace elements due to the oil slick caused by the shipwreck of the Prestige oil tanker, in two species of brown macroalgae (Fucus vesiculosus and Fucus ceranoides) collected from the coastal area most severely affected by the spill (Galicia, NW Spain). The oil slick apparently did not cause significant increases in the concentrations of the trace elements studied, except vanadium. It appears that the magnitude of terrestrial inputs to coastal waters is sufficiently high to mask the inputs of trace elements from the fuel. The observed exception of V suggests that bioaccumulation of this element by the two species of Fucus may be used to indicate exposure to petrochemical products similar to the Prestige fuel. The findings of the study are another example of the importance of the existence of Environmental Specimen Banks for studies of this type.     

Observation of Exchange Interaction in Iron(II) Spin Crossover Molecules in Contact with Passivated Ferromagnetic Surface of Co/Au(111)

Spin crossover (SCO) complexes sensitively react on changes of the environment by a change in the spin of the central metallic ion making them ideal candidates for molecular spintronics. In particular, the composite of SCO complexes and ferromagnetic (FM) surfaces would allow spin-state switching of the molecules in combination with the magnetic exchange interaction to the magnetic substrate. Unfortunately, when depositing SCO complexes on ferromagnetic surfaces, spin-state switching is blocked by the relatively strong interaction between the adsorbed molecules and the surface. Here, the Fe(II) SCO complex [Fe^II(Pyrz)₂] (Pyrz = 3,5-dimethylpyrazolylborate) with sub-monolayer thickness in contact with a passivated FM film of Co on Au(111) is studied. In this case, the molecules preserve thermal spin crossover and at the same time the high-spin species show a sizable exchange interaction of > 0.9 T with the FM Co substrate. These observations provide a feasible design strategy in fabricating SCO-FM hybrid devices.     

Hydrogen production in fluidized bed by chemical-looping cycle

To investigate the feasibility of a chemical-looping hydrogen generation system, we investigated the reduction and water splitting reaction characteristics for three mediators and two reducing gas in a bubbling fluidized bed reactor (0.02 m I.D.). For three oxygen carrier particles (NiO/bentonite, Fe₂O₃/bentonite, (NiO:Fe₂O₃)/bentonite), hydrogen was used as a reduction gas and water was used as an oxidation gas. For (NiO: Fe₂O₃)/bentonite particle, carbon monoxide, which is the main component in the syngas from coal or heavy residue, was used as a reducing gas to check reactivity for the carbon containing fuels and carbon deposition characteristics. Based on the reactivity tests, (NiO: Fe₂O₃)/bentonite particle was selected as the best mediator for the chemical-looping hydrogen generation system to achieve stable continuous operation. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Kinetics of the Initial Stage of Sintering from Shrinkage Data: Simultaneous Determination of Activation Energy and Kinetic Model from a Single Nonisothermal Experiment

A new method for the kinetic analysis of the initial stage of sintering for constant-heating-rate data has been proposed. Unlike all of the methods previously reported in the literature, this new method proposed here allows the simultaneous determination of the activation energy and the kinetic model from a single dilatometric curve recorded under a linear-heating-rate program. The proposed method has been tested with simulated sintering curves and experimental results have been obtained for the sintering of a rutile sample.