高炉出铁沟用Al2O3-SiC-C浇注料流动性和流动性衰减的研究

通过调整氧化硅微粉加入量和活性氧化铝微粉的类型 ,研究了Al2 O3-SiC -C浇注料的流动性和流动性衰减以及可工作时间的变化。结果表明 :在浇注料流动性相近的情况下 ,随着氧化硅微粉加入量的增加 ,加水量显著降低 ;浇注料的流动性与所引入的活性氧化铝微粉的特性密切相关 ;氧化硅微粉加入量的增加有助于延长浇注料的可工作时间 ;浇注料流动性的衰减呈现出先缓慢后迅速降低直至凝结的特点 ,一般在可工作时间之后迅速凝结     

Inhibition of Bacillus cereus spore outgrowth and multiplication by chitosan

Bacillus cereus is an endospore-forming bacterium able to cause food-associated illness. Different treatment processes are used in the food industry to reduce the number of spores and thereby the potential of foodborne disease. Chitosan is a polysaccharide with well-documented antibacterial activity towards vegetative cells. The activity against bacterial spores, spore germination and subsequent outgrowth and growth (the latter two events hereafter denoted (out)growth), however, is poorly documented. By using six different chitosans with defined macromolecular properties, we evaluated the effect of chitosan on Bacillus cereus spore germination and (out)growth using optical density assays and a dipicolinic acid release assay. (Out)growth was inhibited by chitosan, but germination was not. The action of chitosan was found to be concentration-dependent and also closely related to weight average molecular weight (M_w) and fraction of acetylation (F_A) of the biopolymer. Chitosans of low acetylation (F_A = 0.01 or 0.16) inhibited (out)growth more effectively than higher acetylated chitosans (F_A = 0.48). For the F_A = 0.16 chitosans with medium (56.8 kDa) and higher M_w (98.3 kDa), a better (out)growth inhibition was observed compared to low M_w (10.6 kDa) chitosan. The same trend was not evident with chitosans of 0.48 acetylation, where the difference in activity between the low (19.6 kDa) and high M_w (163.0 kDa) chitosans was only minor. In a spore test concentration corresponding to 10²-10³ CFU/ml (spore numbers relevant to food), less chitosan was needed to suppress (out)growth compared to higher spore numbers (equivalent to 10⁸ CFU/ml), as expected. No major differences in chitosan susceptibility between three different strains of B. cereus were detected. Our results contribute to a better understanding of chitosan activity towards bacterial spore germination and (out)growth.     

The occurrence of organochlorines in marine avian top predators along a latitudinal gradient

The aim of this study was to determine the role of cold condensation and fractionation on the occurrence of organochlorine contaminants (OCs) in avian marine top predators along a latitudinal gradient. We measured 24 polychlorinated biphenyl (PCB) congeners and six pesticide OCs in blood of great black-backed gulls (Larus marinus) from the Norwegian Coast (58 degrees N-70 degrees N) and glaucous gulls (Larus hyperboreus) from Bjornoya in the Norwegian Arctic (74 degrees N). Glaucous gulls had up to 3 times higher sigmaOC concentrations compared to the great black-backed gulls, and a OC pattern dominated largely by persistent and low volatile compounds such as highly chlorinated PCBs and metabolites such as oxychlordane. This was not consistent with cold condensation and fractionation theory, but probably related to diet and elevated biomagnification. Among great black-backed gulls, however, there were indications of both cold condensation and fractionation. Higher and lower chlorinated PCBs had highest absolute concentrations in the south and in the north, respectively, except for one location at an intermediate latitude, where concentrations of most OCs exceeded all other locations. In terms of proportional contribution to sigmaOC (pattern), relatively volatile OCs such as HCB, oxychlordane and tri- to penta- PCB congeners were more important at northern latitudes, while hexa- to nona-PCBs made up a larger proportion of sigmaOC in the south. The results thus showed that differences in global distribution of compounds with different physicochemical properties could be detected in avian top predators such as large gulls, even if biomagnification and biotransformation influence both the absolute concentrations and the patterns of OCs.     

铝酸钙水泥、硅酸盐水泥和β-半水石膏混合物中钙矾石的膨胀性能

本文利用现场同步加速X-射线衍射、等温量热仪和膨胀测量等手段,研究了在20℃,100%相对湿度下,由25%(重量比)的铝酸钙水泥、12.5%的硅酸盐水泥、12.5%的β-半水石膏和50%的水组成的浆体的水化。水化伊始,首先形成了石膏和钙矾石,同时半水石膏也相应消耗(0-45min内)。随后石膏继续消耗,钙矾石持续形成,2h45min后石膏消耗完毕,铝酸盐-AFm开始形成,同时钙矾石的数量在7h内保持不变。热曲线的第一个峰源自机械搅拌、初始润湿和溶解,还有钙矾石和石膏的形成,第二个峰为石膏被钙矾石所替代,第三个对应于铝酸盐-AFm的形成。石膏被钙矾石替代伴随着0.7%平均线性膨胀。     

Single-channel blind estimation of arterial input function and tissue impulse response in DCE-MRI

Multipass dynamic MRI and pharmacokinetic modeling are used to estimate perfusion parameters of leaky capillaries. Curve fitting and nonblind deconvolution are the established methods to derive the perfusion estimates from the observed arterial input function (AIF) and tissue tracer concentration function. These nonblind methods are sensitive to errors in the AIF, measured in some nearby artery or estimated by multichannel blind deconvolution. Here, a single-channel blind deconvolution algorithm is presented, which only uses a single tissue tracer concentration function to estimate the corresponding AIF and tissue impulse response function. That way, many errors affecting these functions are reduced. The validity of the algorithm is supported by simulations and tests on real data from mouse. The corresponding nonblind and multichannel methods are also presented.     

Targeted heat treatment of additively manufactured Ti-6Al-4V for controlled formation of Bi-lamellar microstructures

Laser powder bed fusion (L-PBF) was utilized to produce specimens in Ti-6Al-4V,which were subjected to a bi-lamellar heat treatment,which produces microstructures consisting of primary α-lamellae and a fine secondary α-phase inside the inter-lamellar β-regions.The bi-lamellar microstructure was obtained as (i)a direct bi-lamellar heat treatment from the asbuilt condition or (ii) a bi-lamellar heat treatment preceded by a β-homogenization.For the bi-lamellar treatment with β-homogenization,cooling rates in the range 1-500 K/min were applied after homogenization in β-region followed by inter-critical annealing in the α + β region at various temperatures in the range 850-950 ℃.The microstructures were characterized using various microscopical techniques.Mechanical testing with Vickers hardness indentation and tensile testing was performed.The bi-lamellar microstructure was harder when compared to a soft fully lamellar microstructure,because of the presence of fine α-platelets inside the β-lamellae.Final low temperature ageing provided an additional hardness increase by precipitation hardening of the primary α-regions.The age hardened bi-lamellar microstructure shows a similar hardness as the very fine,as-built martensitic microstructure.The bi-lamellar microstructure has more favorable mechanical properties than the as-built condition,which has high strength,but poor ductility.After the bi-lamellar heat treatment,the elongation was improved by more than 250 ％.Due to the very high strength of the as-built condition,loss of tensile strength is unavoidable,resulting in a reduction of tensile strength of～18 ％.     

Borehole stability of multilateral junctions

The oil industry has increased its emphasis on multilateral technology to improve production. This new technology, however, introduces a number of challenges. Junction failure is critical and has resulted in well failures because borehole stability must be maintained to drill and complete these wells successfully.Analytical models that take the junction geometry into account to assess the stability of lateral wellbore branches are presented. The junction is classified into the three following geometries: circular, oval and two adjacent boreholes. A principal conclusion is that any geometry that deviates from a circle leads to less stability. The stability window at the junction itself is smaller than the borehole above or below. Both fracturing and collapse at the multilateral junction are analyzed. A field case is discussed to demonstrate the application of the models.     

Designers as the determinants of design innovations

Design innovations have become increasingly important appropriation mechanisms for firms. Since 2003, the number of applications for design rights (protecting design innovations) has tripled compared to a doubling in the numbers of both patent and trademark applications. However, despite the growing interest of firms in design innovations, knowledge of the determinants of design innovations is limited. Prior work on labour mobility within the innovation studies literature has focused primarily on the discussion of scientists as being crucial for the creation of technological innovations. The present paper expands on this discussion by drawing parallels with the relation between scientists and technological innovation and the relation between designers and design innovation. We explore whether a similar positive relationship exists between the labour mobility of designers and the generation of design innovations and which determinants influence this relation. We employ a unique Danish dataset containing information on firms, their hiring of designers, and their design innovation activity measured by design rights. Our findings show that hiring a designer does increase the likelihood of producing a design innovation. Hence, designers are a determinant of design innovations. However, in order for the firm to benefit fully from hiring a designer, prior experience in design innovation is required.