Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

A novel InP/InGaAs TEBT for ultralow current operations

A novel InP/InGaAs tunneling emitter bipolar transistor (TEBT) is fabricated and demonstrated. The studied device exhibits a very small collector-emitter offset voltage of 40 mV and an extremely wide operation regime. The operation region is larger than 11 decades in magnitude of collector current (10/sup -12/ to 10/sup -1/A). A current gain of 3 is obtained even if the device is operated at an ultralow collector current of 3.9 /spl times/ 10/sup -12/A (1.56 /spl times/ 10/sup -7/A/cm/sup 2/). Furthermore, the common-emitter breakdown voltage of the studied device is higher than 2 V. Consequently, the studied device shows a promise for low supply voltage, and low-power consumption circuit applications.     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

An efficient mixed algorithm of L-MEI and DDM for the wavescattering by a concave cylinder

In this paper, a localized MEI method (L-MEI) is developed and combined with the domain decomposition method (DDM) for the simulation of scattering by a concave cylinder. In the L-MEI, the whole domain is decomposed into many subdomains. Different from the conventional MEI method, the MEI coefficients of the L-MEI method in each subdomain are only dependent on the localized metrons that are defined in the subdomain. The localization of metrons has the following advantages: (1) speeding up the calculation of MEI coefficients and saving memory, (2) making the MEI method available for concave structures, and (3) obtaining a band sparse matrix directly without any modification     

An EM‐based adaptive multiple target tracking filter

Tracking targets of interest is one of the major research areas in radar surveillance systems. We formulate the problem as incomplete data estimation and apply EM to the MAP estimate. The resulting filter has a recursive structure analogous to the Kalman filter. The advantage is that the measurement‐update deals with multiple measurements in parallel and the parameter‐update estimates the system parameters on the fly. Experiments tracking separate targets in parallel show that tracking maintenance ratio of the proposed system is better than that of NNF and RMS position error is smaller than that of PDAF. Also, the system parameters are correctly obtained even from incorrect initial values. Copyright © 2001 John Wiley & Sons, Ltd.     

A general framework for debugging

The state of the art of debugging is examined. A debugged process model that serves as the basis of a general debugging framework is described. The relationship of the model to traditional debugging processes and support tools is discussed. A minimal set of requirements for a general debugging framework is described in terms of both the theory behind debugging methodologies and the support tools. An execution monitor, Eden, that serves as a debugging tool within this general framework is described     

Direct adaptive control of nonminimum phase systems using integralaction

A direct adaptive control scheme is proposed for nonminimum-phase systems in which controller parameters are estimated from the recursive least-squares algorithm and additional auxiliary parameters are obtained from the proposed polynomial identity. A local convergence is guaranteed without any extra condition. Integral action is incorporated into the adaptive controller to eliminate the steady-state error and to satisfy a condition of the unique solution for the polynomial identity. The control law used in this scheme is based on the set-point-on-I-only proportional-integral-derivative (PID) structure     

Online and Offline Rotary Regression Analysis of Torque Estimator for Switched Reluctance Motor Drives

A new torque estimator for switched reluctance motor (SRM) drives based on 2-D rotary regression analysis is presented in this paper. The proposed torque estimator is composed of a bicubic regressive polynomial as a function of rotor position and input current. The regressive coefficients can be computed offline or online from the torque characteristics acquired either experimentally or from numerical computation. Furthermore, a torque estimation method by taking mutual coupling into consideration is proposed. It can be seen that the estimated and experimentally obtained self-coupling and mutual-coupling torque characteristics are in good agreement with each other. In addition, the dynamic torque waveforms with and without the mutual coupling, estimated by the proposed estimator, are found to be virtually the same as those obtained from the bicubic spline interpolation for SRM drives with single-pulse voltage, hysteresis current chopping, as well as with voltage pulse width modulation control. The success of all the case studies being reported is a good validation of the usefulness and accuracy of the proposed real-time torque estimator that, as described in this paper, can be used to quickly estimate the instantaneous output torque of SRM drives.     

Enhanced electron emission from phosphorus-doped diamond-cladsilicon field emitter arrays

Undoped and phosphorus (P)-doped diamond-clad Si field emitter arrays have been successfully fabricated using microwave plasma chemical vapor deposition (MPCVD) technology. The electron emission from the blunt diamond-clad microtips are much higher than those for the pure Si tips with sharp curvature due to a lower work function. Furthermore, the characteristics of emission current against applied voltage for the P-doped diamond-clad tips show superior emission at lower field to the undoped ones. After the examination of Auger electron spectroscopy (AES) and electrical characteristics of as-grown diamond, such a significant enhancement of the electron emission from the P-doped diamond-clad tips is attributed to a higher electron conductivity and defect densities