Effects of genotype and treatment on the antioxidant activity of sweet potato in Taiwan

Six genotypes of sweet potato commercially available in Taiwan, including TNG57, TNG66, TNG68, TYY1, RP and WP, were used as samples in this study of the effects of steaming and kneading with pre-steaming treatments on the antioxidant components and antioxidant properties of methanolic extracts. Steam treatment increased the total phenols contents of all genotypes (2–13 times), flavonoids content of RP (1.3 times) and anthocyanins contents of RP and WP (5–6 times). Steam treatment also increased the reducing power and scavenging DPPH radical effect of sweet potato flours. For the methanolic extracts of steamed and kneaded flours, reducing powers were 0.02–1.70 at 5.0 mg ml⁻¹ and the scavenging effects on DPPH radicals were 19–92% at 2.5 mg ml⁻¹. Both showed the order of RP > WP > TYY1 and TNG66 > TNG57 and TNG68. However, the chelating effect of the six genotypes at 1.0 mg ml⁻¹ ranged from 50% to 73%. Contents of total phenols, flavonoids, and anthocyanins of sweet potato flours were significantly positively correlated with the reducing power and scavenging DPPH radical effects. After steaming and kneading treatments, RP showed the highest increase in the contents of total phenols, flavonoids and anthocyanins among the six genotypes studied.     

Influence of ethyl methacrylate content on the volume‐phase transition of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] microgels

A novel series of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] (p(NIPAM‐co‐EMA)) microgels was prepared by the surfactant‐free radical polymerization of N‐isopropylacrylamide (NIPAM) with ethyl methacrylate (EMA). The shape, size dispersity and volume‐phase transition behavior of the microgels were investigated by transmission electron microscopy (TEM), ultraviolet–visible (UV–Vis) spectroscopy, dynamic light scattering (DLS) and differential scanning calorimetry (DSC). The transmission electron micrographs and DLS results showed that microgels with narrow distributions were prepared. It was shown from UV–Vis, DLS and DSC measurements that the volume‐phase transition temperature (VPTT) of the p(NIPAM‐co‐EMA) microgels decreased with increasing incorporation of EMA, but the temperature‐sensitivity was impaired when more EMA was incorporated, causing the volume‐phase transition of the microgels to become more continuous. It is noteworthy that incorporation of moderate amounts of EMA could not only lower the VPTT but also enhance the temperature‐sensitivity of the microgels. The reason for this phenomenon could be attributed to changes in the complicated interactions between the various molecules. Copyright © 2004 Society of Chemical Industry     

Feasibility analysis of membrane reactors – discovery of reactive arheotropes

A feasibility analysis methodology adopted from reactive distillation is applied to membrane reactors. A model is formulated to depict the reactive liquid phase composition on the retentate side of a continuous type membrane reactor. The effects of both the chemical reaction kinetics and the membrane mass transfer kinetics on the feasible products are elucidated by means of retentate phase diagrams and bifurcation analysis. The proposed method can be applied to various membrane processes, independent of the specific structure of the membrane. Two quaternary reaction systems are considered to illustrate the methodology. In the first hypothetical system, it is shown how selective membranes can influence the sequence of effective volatilities which in turn affects the feasible products of the system. In the second example of practical importance, i.e. the heterogeneously catalysed synthesis of propyl acetate coupled with permeation through a porous polycarbonate membrane, the dusty gas model is applied to describe the component fluxes through the membrane. For the latter reaction system, the existence of reactive arheotrope is demonstrated. Arheotropes represent mass transfer controlled feasible products of membrane separation process.     

Treatment of low turbidity water by sweep coagulation using bentonite

A novel strategy of sweep coagulation to treat low turbidity water is presented herein. Study findings demonstrated that an Na⁺‐saturated bentonite with medium cation exchange capacity (CEC) resulted in significant turbidity removal at a bentonite dosage of 30 mg dm^?3. Bentonite dispersion with fully delaminated platelets tended to undergo a more porous type of coagulation with intense face‐to‐face interactions of platelets and effectively entrapped TiO₂ particles in band‐type structures. This type of coagulation usually results in a large volume of settled flocs with a fluffy structure and excellent turbidity removal efficiency for sweep coagulation. The sign and magnitude of electrical charge on TiO₂ particles has a minor effect on the efficiency of sweep coagulation. Copyright © 2005 Society of Chemical Industry     

Preirradiation grafting of acrylic and methacrylic acid onto polyethylene films: Preparation and properties

The method of preirradiation grafting of acrylic acid and methacrylic acid onto polyethylene films was studied. The trapped radicals and hydroperoxides or diperoxides appeared to be able to induce graft polymerization. Mohr's salt was added to depress homopolymerization. The influences of crystallinity, dosage, and storage period on the grafting behavior were investigated from the viewpoint of practical application. At elevated temperature, the degree of grafting increased rapidly with reaction time initially, and then leveled off to the value of final percent grafting. Dosage and storage periods had greater extent of influence on the final percent grafting of LDPE than on that of HDPE. Electrical properties, transport properties, and mechanical properties were measured to compare the differences between acrylic-acid-and methacrylic-acid-grafted copolymer films. It was found that the properties of methacrylic-acid-grafted copolymer film was superior to those of acrylic-acid-grafted copolymer film, especially in electrical conductivity. The KOH diffusion test confirmed that grafting occurred not only on the surface but also in the interior of the polymer matrix, and the grafting is believed to proceed from the surface to the interior of the matrix.     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

Exact evaluation of laser linewidth requirements for optical PSKhomodyne communication systems with balanced PLL receivers

The power penalty induced by imperfect phase recovery in PSK homodyne communication systems with balanced phase-locked loop receivers are exactly evaluated. Optimum phase deviations between the mark-state and the space-state bits are used in this study. This study for the first time shows the imperfect-phase-recovery-induced power penalty as a function of laser linewidth with optimum phase deviations considered. It can be estimated from the theoretical result that an optimal balanced PLL receiver requires the laser linewidth as Δν⩽1.15×10^-6× (bit rate) in contrast to the previous reported one Δν⩽5.88×10^-6× (bit rate). We also point out here that the previously reported laser linewidth requirement was wrongly estimated     

Towards a generalized TLM algorithm for solving arbitraryreciprocal and nonreciprocal planar structures

A generalized transmission line matrix (TLM) algorithm is developed in the frequency domain to tackle arbitrary both reciprocal and nonreciprocal anisotropic waveguiding problems. In particular, the modeling issue for arbitrary planar structures is stressed in this work. A new three-dimensional (3-D) condensed node is used to consider the effect of both electric and magnetic constitutive tensors. Various results indicate how the modal dispersive behavior can be manipulated by changing not only the anisotropic characteristics of the substrate, but also the strip/slot geometry as well as the magnitude and orientation of the applied static magnetic field. The present algorithm is useful for CAD and simulation of a large class of gyrotropic waveguide-based microwave and millimeter-wave circuits