Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Synthesis and characterization of functional gradient copolymers of glycidyl methacrylate and butyl acrylate

Epoxy-functional spontaneous gradient copolymers of glycidyl methacrylate (G) and n-butyl acrylate (B) were synthesized via atom transfer radical polymerization (ATRP). The copolymerization reactions were carried out in toluene solution at 70 °C, using methyl 2-bromopropionate (MBrP) as initiator and copper chloride with N,N,N′,N′′,N′′-pentamethyldiethylenetriamine (PMDETA) as the catalyst system. The kinetic behaviour of the statistical copolymerizations was studied in a wide composition interval with molar fractions of G ranging from 0.10 to 0.75. The synthesized copolymers were characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. ¹H NMR was employed to determine the copolymer composition, demonstrating the gradient character of the copolymers along the main chain in the whole monomer conversion interval. Apart from this, the sequence distribution and stereoregularity were analyzed. These microstructural experimental data agreed well with those calculated from Mayo-Lewis terminal model (MLTM) and a Bernoullian statistic with an isotacticity parameter of σ_G = 0.28 and a coisotacticity parameter of σ = 0.30.     

Composing RESTful Services and Collaborative Workflows: A Lightweight Approach

The use of RESTful Web services has gained momentum in the development of distributed applications based on traditional Web standards such as HTTP. In particular, these services can integrate easily into various applications, such as mashups. Composing RESTful services into Web-scale workflows requires a lightweight composition language that's capable of describing both the control and data flow that constitute a workflow. The authors address these issues with Bite, a lightweight and extensible composition language that enables the creation of Web-scale workflows and uses RESTful services as its main composable entities.     

Hull-less Barley Varieties: Storage Proteins and Amino Acid Distribution in Relation to Nutritional Quality

Barley (Hordeum vulgare L.) has had an important impact on human nutrition. Hull-less barley is a genetically improved type that has been widely used in recent years. Six Brazilian hull-less barley varieties (IAC-IBON 214-82; IAC 8612-421; IAC 8501-31; IAC 8501-12; IAPAR 39-ACUMAI; IAC 8501-22) were analyzed for storage protein constituents, amino acid contents, and similarity among the hull-less barley varieties. Albumins, globulins, prolamins I and II, and glutelins were extracted and separated by SDS-PAGE. The total protein amino acid contents of the flour were also determined for each variety by TLC and HPLC. Variations in intensity and appearance and disappearance of protein bands were observed among the varieties suggesting genetic variability. However, the amino acid profile did not indicate any major variations in the amino acid concentrations. The high lysine and threonine total concentrations detected in the seeds of the hull-less barley varieties encouraged an investigation into the regulation of amino acid metabolism and storage protein synthesis.     

Transport of chromium(VI) through a Cyanex 921‐supported liquid membrane from HCl solutions

The transport of chromium(VI) through a flat‐sheet supported liquid membrane containing Cyanex 921 as a carrier has been investigated. The permeation of the metal is investigated as a function of various experimental variables: hydrodynamic conditions, concentration of chromium(VI) and HCl in the feed phase, carrier concentration and diluent in the membrane and strippant concentration in the stripping phase. The mass transfer coefficient and the thickness of the aqueous boundary layer were calculated from the experimental data. Furthermore, the selectivity of Cyanex 921‐based flat‐sheet supported liquid membrane towards different metal ions and the behaviour of the system against other carriers are presented. Copyright © 2003 Society of Chemical Industry     

Epoxide polymerization

Summary Poly(propylene oxide), PPO, obtained using diphenylzinc, Ph₂Zn, and using the diphenylzinc-water system at various molar ratios H₂O/Ph₂Zn, were studied through ¹H NMR and IR spectroscopy establishing that the polymerization initiates by coordition of propylene oxide (PO) to a terminal zinc atom of the active species followed by consecutive insertions of PO units at this zinc atom. The PPO obtained showed Ph-and HO-, HO-and HO-end-groups depending on the molar ratio H₂O/Ph²Zn used, and also HO-and PhO-end-groups when oxygen was present in the polymerization system.     

Application of Romero García method to the degradation process of DGEBA/ETDA filled with ultra fine metallic copper

Summary The thermal properties of an epoxy resin (diglycidyl ether Bisphenol A, DGEBA) cured with a primary amine (ethylenediamine, ETDA) and filled with 10, 20 and 30 wt. % of ultra fine copper particles were analyzed. The thermal results were evaluated by means of the Romero-Garcia method, which allowed to obtain the resin degradation kinetic parameters, as well as the possible decomposition mechanism. From the obtained results is possible to infer that higger copper content strongly affects the degradation process of the epoxy resin, which causes a drop off on the composites thermal stability. This behavior could be attributed to water presence, being this effect less pronounced for the resin with 10 wt. % copper and unfilled resin. Regarding to decomposition mechanism, three way transport showed the best correlation for all samples.     

A Study of Ozone Generation by Negative Corona Discharge Through Different Plasma Chemistry Models

The Steady radial distribution of chemical species in a wire‐to‐cylinder ozone generator filled with pure oxygen has been computed by applying four different plasma chemistry models of increasing complexity. The most complete model considers ten species (e, O₂ ⁺, O₂ ^?, O₃ ^?, O^?, O₂, O₂(¹Δ_g), O₂(¹∑_g ⁺), O and O₃) and 79 reactions, including ionization by electron impact, electron attachment and detachment, electron-ion recombination, charge transfer, etc. The chemical model is coupled with the electrical model through Poisson's equation. The spatially averaged ozone density has been computed as a function of the current intensity and compared with the experimental values obtained by UV spectroscopy.     

Inhibition of sulfide on the simultaneous removal of nitrate and p‐cresol by a denitrifying sludge

BACKGROUND: Many industrial discharges, such as those generated from petrochemical refineries, contain large amounts of sulfurous, nitrogenous and organic contaminants. Denitrification has emerged as a suitable technology for the simultaneous removal of these pollutants in a single reactor unit; however, more evidence is demanded to clarify the limitations of denitrification on the simultaneous removal of sulfide and phenolic contaminants and to optimize the biological process. The aim of this study was to evaluate the capacity of a denitrifying sludge to simultaneously convert sulfide and p‐cresol via denitrification. RESULTS: Sulfide was the preferred electron donor over p‐cresol, imposing a 5 h lag phase (required for complete sulfide removal) on organotrophic denitrification. Addition of sulfide (20 mg S^2? L^?1) to p‐cresol‐amended denitrifying cultures also decreased the reduction rate of nitrate and nitrite, as well as the production rate of nitrogen gas. Nitrite reduction rate was the most affected step by sulfide, decreasing from 35 to 21 mg N (g VSS d)^?1. A synergistic inhibitory effect of nitrate and sulfide was also observed on nitrite reduction. Despite the effects of sulfide on the respiratory rates monitored, complete removal of nitrate, sulfide and p‐cresol could be achieved after 48 h of incubation. CONCLUSION: Our results suggest that simultaneous removal of sulfide and p‐cresol could be achieved in denitrifying reactors, but a large hydraulic residence time may be required to sustain an efficient process due to inhibitory effects of sulfide. Copyright © 2008 Society of Chemical Industry     

Mapping of Trellises Associated with General Encoders onto High-Performance VLSI Architectures

A rate 1/n binary generic convolutional encoder is a shift-register circuit where the inputs are information bits and the outputs are blocks of n bits generated as linear combinations on the appropriate shift register contents. The decoding of the outputs of a convolutional encoder can be carried out by the well-known Viterbi algorithm. The communication pattern of the Viterbi Algorithm is given as a graph, called trellis, associated to the state diagram of the corresponding encoder. In this paper we present a methodology that permits the efficient mapping of the Viterbi algorithm onto a column of an arbitrary number of processors. This is done through the representation of the data flow by using mathematical operators which present an inmediate hardware projection. A single operator string has been obtained to represent a generic encoder through the study of the data flow of free-forward encoders and feed-back encoders. The formal model developed is employed for the partitioning of the computations among an arbitrary number of processors in such a way that the data are recirculated opimizing the use of the processors and the communications. As a result, we obtain a highly regular and modular architecture suitable for VLSI implementation.