Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Finite element analysis of loaded structures at very high temperatures

At very high temperatures loaded metallic structures undergo creep deformations. The generated creep strains are connected with stress relaxations, stress redistributions and/or progressive deformations.In mainly load controlled situations the behaviour of the material can be described by a nonlinear viscous flow law (Norton power law).A stress-deformation analysis of complex structures can be carried out by finite element codes in which the mentioned constitutive equation is implemented. The code PERMAS-VISCOUS was used to analyse the stress state of a notched tension bar and the deformation behaviour of a tube under external pressure undergoing a creep collapse. The relation to experimental findings is also given.     

Density functional theory studies of Cu-zeolite de-NOx catalysts

Summary Recent progress in the modelling of exchanged Cu sites and their interactions with small molecules, based on DFT cluster calculations, is briefly reviewed.     

0.27-dB/km attenuation achieved by MSP preform process [opticalfibers]

Mechanically shaped preforms (MSP) have been demonstrated to combine economic non-CVD (chemical vapor deposition) processing and low loss, with a published value of 0.63 dB/km and a size of 30 fkm/preform. Improved processing is proposed which results in a minimum loss of 0.27 dB/km at 1550 nm. Preforms capable of yielding 150 fkm have been produced. Reboiling during preform stretching and fiber pulling is identified as the last remaining problem of the process     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

Stretching and deformation vibrations of CH2, C(CH3) and O(CH3) groups of poly(methyl methacrylate)

Infrared and Raman spectra of atactic PMMA and infrared spectra of stereoregular PMMA and of its four deuterated derivatives

, were measured. They were used to assign the bands of stretching and deformation vibrations of CH₂, CCH₃ and OCH₃ groups in the infrared and Raman spectra and to discuss the effect of stereoregularity on these bands in the infrared spectra.