Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

Heat and Mass Transfer Analogy Studies of Binary Liquid Mixture in Comparison with Eteanol-n-Heptane Evaporating to Air

An expenmental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 mls. An illustrative example of the use of the theory for industrial ventilation is presented.     

Nanowire encapsulation with polymer for electrical isolation and enhanced optical properties

Light management and electrical isolation are essential for the majority of optoelectronic nanowire (NW) devices.Here,we present a cost-effective technique,based on vapor-phase deposition of parylene-C and subsequent annealing,that provides conformal encapsulation,anti-reflective coating,improved optical properties,and electrical insulation for GaAs nanowires.The process presented allows facile encapsulation and insulation that is suitable for any nanowire structure.In particular,the parylene-C encapsulation functions as an efficient antireflection coating for the nanowires,with reflectivity down to ＜1％ in the visible spectrum.Furthermore,the parylene-C coating increases photoluminescence intensity,suggesting improved light guiding to the NWs.Finally,based on this process,a NW LED was fabricated,which showed good diode performance and a clear electroluminescence signal.We believe the process can expand the fabrication possibilities and improve the performance of optoelectronic nanowire devices.     

Concerted utility review of VVER-440 safety research needs (VERSAFE)

There are twelve operating VVER-440/213 reactors in the Czech Republic, Hungary and Slovakia. The plant owners have carried out extensive safety enhancement programmes, which have included measures to improve prevention, mitigation and control of design basis accidents. Recently, there have been a number of projects to study the Severe Accident Management aspects of these plants. The plant owners have also initiated Plant Life Management programmes. The objective of the VERSAFE Concerted Action is to create a network of the VVER-440/213 plant owners and operators, which aims at definition of the further research needs of severe accidents and plant ageing from the utilities’ viewpoint. The starting point is to formulate a general approach to severe accident management and plant life management and then proceed to define the needs for the additional information expected from the safety research. The role of national research institutes and organisations of the partner countries is of crucial importance in performing such research and, thus, creating and maintaining the expertise on the national level. The successful completion of the project will assist in establishing well-defined research projects that are oriented to the needs of the end-users and provide information that can be used to facilitate and support the negotiations of the EU applicant countries operating VVER-440 reactors.     

Perceptions of the health and convenience characteristics of fresh and dried fruits

Dried fruits consumption has not received much research attention, although these foods are associated with potential health benefits. Therefore, the aim of this study was to compare fresh fruits and dried fruits on measures of health, convenience and consumer feelings.An on-line questionnaire that measured consumers' perceptions of the health benefits and convenience characteristics and their feelings about the consumption of both fresh fruits (apples and plums) and dried fruits (e.g., raisins, dates, and apricots) was completed by 693 respondents (Polish, French, and Dutch).Generally, fresh fruits were perceived to be healthier and less convenient than dried fruits. Consumers also reported more positive feelings about the consumption of fresh fruits compared to dried fruits. The more that the respondents were willing to sacrifice for their health, the more positively they rated the health aspects of both fresh and dried fruits, as well as several perceptions of convenience of both fresh and dried fruits. Health preoccupation was unrelated to most of the convenience perceptions and was associated with lower scores on several perceptions of healthiness. Recommendations for the consumer-oriented development of dried fruits are also provided.     

Challenges of manufacturability and product data management in bending

Effective production in a networking environment of sheet metal products needs accurate and relevant PDM (product data management) data, appropriate modeling of components supported by local and global network solutions, and utilization of advantages of feature-based modeling. To enable these aspects of effective production in sheet metal production, it is necessary to evaluate the integration of DFMA (design for manufacturing and assembly) and PDM. This paper aims at identifying the challenges of DFMA and PDM integration through recognizing possible malfunctioning parts of their integration. The observations are based on sheet metal specimens in which the DFMA and PDM aspects are visible in punching and bending. This study will focus on five issues that are included either in DFMA or PDM, or both: the effects of different calculation methods for the flattened length, utilization viewpoints of global or local manufacturability guidelines, assembly conditions, options to tune the manufacturing process instead of changing the product geometry, and possible additional requirements given by the customers. Based on practical design and manufacturing tests, it has become evident that one option to improve the quality of analyzed sheet metal parts is to further develop the integration of DFMA features with the workshop’s cutting and punching parameters. As one possible improvement to these kinds of integration tasks of DFMA and PDM, it is suggested that the responsibilities for developing DMFA and PDM applications with proper design parameters could be analyzed more deeply between persons working with information exchange, product design, software design, or production machine design.     

Development and application of an automated subcatchment generator for SWMM using open data

An open source subcatchment generator program was developed for the Stormwater Management Model (SWMM) to automate tedious stages in the model construction process. The generator divides the investigated area into subcatchments using a uniform computation grid and connects the grid cells together and to the underlying stormwater network. The system was tested by applying it to two small urban catchments with different fractions of impervious surfaces in Helsinki, Finland, using mostly openly available data. The simulated discharge results were compared to measured data and to results obtained from manually built models. The proposed system significantly accelerated the setup of a SWMM modelling project, as the routing between the subcatchments as well as the subcatchment slopes and flow widths were directly derived from the computation grid. Automatically generated and manually constructed SWMM models produced discharge results that differed only slightly from each other.     

On the asymptotic behaviour of shells of revolution in free vibration

We consider the free vibration problem of thin shells of revolution of constant type of geometry, focusing on the asymptotic behaviour of the lowest eigenfrequency, as the thickness tends to zero. Numerical experiments are computed using two discretization methods, collocation and finite elements, each corresponding to a different shell model. Our results are in agreement with theoretical results obtained using interpolation theory and cited in literature.     

Strength retention of drawn self-reinforced polyglycolide rods and fixation properties of the distal femoral osteotomies with these rods. An experimental study on rats

Drawn self-reinforced polyglycolide (SR-PGA) rods, Ø 2 mm and 26 mm long, were implanted in the dorsal subcutaneus tissue of 16 rats. Osteotomies of the distal femur were fixed with SR-PGA rods (2 mm by 15 mm) in another 38 rats. The follow-up times varied from one week to one year. After sacrifice, three-point bending and shear tests were performed for subcutaneously placed rods. Radiological, histological, histomorphometrical, microradiographic, and oxytetracycline-fluorescence studies of osteotomized and intact control femora were also performed. At three weeks the flexural strength of the rods was 50% of the initial value, and the flexural modulus was 46% of the initial value. Five osteotomy specimens had to be excluded due to dislocation or non-union. One of the 33 evaluated osteotomy specimens showed signs of postoperative infection. Thirty-two osteotomies healed uneventfully. No gross signs of inflammatory or foreign-body reaction were observed. The amount of osteoid surface and active osteoid formation surface reached their highest value in the histomorphometrical analysis at 24 weeks. The present investigation demonstrated that the mechanical strength and fixation properties of the drawn SR-PGA rods are suitable for fixation of cancellous bone osteotomies in rats. The present article is the first report on the successful application of drawn SR-PGA rods for fixation of cancellous bone osteotomies.