Kinetics of two-step anionic polymerization

This article deals with the kinetics of two-step anionic polymerization by way of a non-steady state method. Several molecular parameters can be evaluated using the formulae developed. A bimodal molecular weight distribution function for the resulting polymer is derived from the set of kinetic differential equations, which is in agreement with the experimental data reported.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

Modelling biological processes under anaerobic conditions through integrating titrimetric and off-gas measurements-applied to EBPR systems.

An innovative method for modelling biological processes under anaerobic conditions is presented and discussed. The method is based on titrimetric and off-gas measurements. Titrimetric data is recorded as the addition rate of hydroxyl ions or protons that is required to maintain pH in a bioreactor at a constant level. An off-gas analysis arrangement measures, among other things, the transfer rate of carbon dioxide. The integration of these signals results in a continuous signal which is solely related to the biological reactions. When coupled with a mathematical model of the biological reactions, the signal allows a detailed characterisation of these reactions, which would otherwise be difficult to achieve. Two applications of the method to the enhanced biological phosphorus removal processes are presented and discussed to demonstrate the principle and effectiveness of the method.     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

Microstructure study of Sm,Mn-modified PbTiO3 piezoelectric ceramics by XRD profile-fitting technique

By using the X-ray diffraction profile-fitting technique, the microstructures of Sm, Mn-modified PbTiO₃ piezoelectric ceramic discs, including ferroelectric domain sizes, microstrains, and their variations with the poling strength have been quantitatively investigated. The results manifest that the modified PbTiO₃ ceramics contain a high density of domain walls due to the presence of finely-divided coherent domain structures (tens of nanometres in dimension). The poling treament can evidently influence the domain-size distribution, with a more homogeneous microstructure being developed; however, it simultaneously causes high anisotropic microstrains within the structure which, together with the high density of domain walls, is expected to be responsible for the unusual high electromechanical coupling properties possessed by this material.     

Surface charge accumulation and decay on a spacer stressed with DC voltages at atmospheric conditions

Contents Surface charge accumulation and its decay at a GIS spacer are studied at atmospheric conditions employing a two step-calibration method. The results show that the accumulation saturates within 30 minutes; the dominant mechanism of surface charge accumulation is the drift of charged particles via air, while that of the decay is surface conduction. The characteristics are similar at both polarities.

---

Sättigungskonzentration und Abklingverhalten der Oberflächenladung an einem mit Gleichspannung beanspruchten Abstandshalter unter atmosphärischen Bedingungen

Übersicht Die Konzentration und das Abklingen von Oberflächenladungen an einem GIS Abstandshalter wurden unter atmosphärischen Bedingungen mit Hilfe eines zweistufigen Kalibrierungsverfahrens untersucht. Die Ergebnisse zeigen eine Sättigung der Ladungskonzentration innerhalb von 30 Minuten. Als Hauptursache der Ladungskonzentration ist die Drift geladener Teilchen in Luft anzusehen, während das Abklingen auf die Oberflächenleitung zurückzuführen ist. Ähnliche Charakteristiken ergeben sich mit beiden Polaritäten.

     

Effective sludge solubilization treatment by simultaneous use of ultrasonic and electrochemical processes.

Sludge disintegration treatment by using simultaneously ultrasonic irradiation and electrolysis was investigated experimentally. A lab-scale diaphragm cell irradiated with ultrasound at a constant oscillating frequency of 20 kHz was used as a reactor. The batch experiments were carried out under different conditions of electric outputs of the ultrasonic generator, electric current for the electrolysis and different initial SS concentrations. A simultaneous treatment in the cathodic compartment without any chemical doses considerably facilitated the sludge solubilization, compared to the sonication alone. An increase in the electric current up to 400 mA under a constant ultrasonic density decreased the specific energy by 55% within the experimental range. The specific energy consumption was also reduced when the initial SS concentration increased. In addition, before carrying out the simultaneous treatment, a brief electrolysis was effective for further reduction of the specific energy and the acceleration of soluble COD generation.     

Evaluation of Soybean Seedcoat Cracking During Drying:PART II. Using MRI

MRI techniques were developed and employed for non-destructive and noninvasive study of seedcoat cracking in low moisture soybean kernels during heated air drying. Proton density image and transient moisture distribution profile of a single soybean kernel can be obtained using MRI. These MRI techniques proved to be particularly useful for the continuous observation of initiation and propagation of seedcoat cracking during the entire period of drying process without interruption.

The proton density images of soybean kernels showed that seedcoat cracking was initiated perpendicular to the long axis of the kernel near the hilum. The transient moisture distribution profiles in soybean kernels during drying indicate that moisture gradient developed during drying was higher in the seedcoat than in the cotyledon. Drying temperature and initial average moisture content were positively correlated with the soyhean seedcoat crackig. The location of the